Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOLE MOBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Dual-pilot tone calibration technique

Pilot-based calibration techniques are used to reduce the effects of multipath fading in mobile satellite receivers. One of the more recent of these techniques, namely the tone calibration technique (TCT), suggests transmitting double sideband modulation with the pilot tone located at the center of its spectrum where the amplitude and phase characteristics of the channel are most stable. To 'make room' for the pilot in the presence of the Doppler shift, the equivalent low-pass data sidebands must be shaped so as to have zero response in the neighborhood of dc. Other techniques such as transparent tone-in-band (TTIB) similarly 'notch out' a hole in the center of the data spectrum for location of the pilot. An alternate possibility which is at the same time much more bandwidth efficient than TCT is a dual-pilot tone calibration technique (DPTCT) that symmetrically locates a pair of pilots outside the data spectrum near the band edges of the channel. The operation and performance of DPTCT are analyzed, and its effectiveness is compared to that of the single tone TCT technique.

Simon, Marvin K.↗

Studies of photoconductivity and field effect transistor behavior in examining drift mobility, surface depletion, and transient effects in Si-doped GaN nanowires in vacuum and air

Variable intensity photoconductivity (PC) performed under vacuum at 325 nm was used to estimate drift mobility ({mu}) and density ({sigma}{sub s}) of negative surface charge for c-axis oriented Si-doped GaN nanowires (NWs). In this approach, we assumed that {sigma}{sub s} was responsible for the equilibrium surface band bending ( Empty-Set ) and surface depletion in the absence of illumination. The NWs were grown by molecular beam epitaxy to a length of approximately 10 {mu}m and exhibited negligible taper. The free carrier concentration (N) was separately measured using Raman scattering which yielded N = (2.5 {+-} 0.3) Multiplication-Sign 10{sup 17} cm{sup -3} for the growth batch studied under 325 nm excitation. Saturation of the PC was interpreted as a flatband condition whereby Empty-Set was eliminated via the injection of photogenerated holes. Measurements of dark and saturated photocurrents, N, NW dimensions, and dimensional uncertainties, were used as input to a temperature-dependent cylindrical Poisson equation based model, yielding {sigma}{sub s} in the range of (3.5 to 7.5) Multiplication-Sign 10{sup 11} cm{sup -2} and {mu} in the range of (850 to 2100) cm{sup 2}/(V s) across the (75 to 194) nm span of individual NW diameters examined. Data illustrating the spectral dependence and polarization dependence of the PC are also presented. Back-gating these devices, and devices from other growth batches, as field effect transistors (FETs) was found to not be a reliable means to estimate transport parameters (e.g., {mu} and {sigma}{sub s}) due to long-term current drift. The current drift was ascribed to screening of the FET back gate by injected positive charge. We describe how these gate charging effects can be exploited as a means to hasten the otherwise long recovery time of NW devices used as photoconductive detectors. Additionally, we present data illustrating comparative drift effects under vacuum, room air, and dry air for both back-gated NW FETs and top-gated NW MESFETs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

M.I.N.G., Mars Investment for a New Generation: Robotic construction of a permanently manned Mars base

A basic procedure for robotically constructing a manned Mars base is outlined. The research procedure was divided into three areas: environment, robotics, and habitat. The base as designed will consist of these components: two power plants, communication facilities, a habitat complex, and a hangar, a garage, recreation and manufacturing facilities. The power plants will be self-contained nuclear fission reactors placed approx. 1 km from the base for safety considerations. The base communication system will use a combination of orbiting satellites and surface relay stations. This system is necessary for robotic contact with Phobos and any future communication requirements. The habitat complex will consist of six self-contained modules: core, biosphere, science, living quarters, galley/storage, and a sick bay which will be brought from Phobos. The complex will be set into an excavated hole and covered with approximately 0.5 m of sandbags to provide radiation protection for the astronauts. The recreation, hangar, garage, and manufacturing facilities will each be transformed from the four one-way landers. The complete complex will be built by autonomous, artificially intelligent robots. Robots incorporated into the design are as follows: Large Modular Construction Robots with detachable arms capable of large scale construction activities; Small Maneuverable Robotic Servicers capable of performing delicate tasks normally requiring a suited astronaut; and a trailer vehicle with modular type attachments to complete specific tasks; and finally, Mobile Autonomous Rechargeable Transporters capable of transferring air and water from the manufacturing facility to the habitat complex.

Amos, Jeff↗

Failure Analysis Results and Corrective Actions Implemented for the Extravehicular Mobility Unit 3011 Water in the Helmet Mishap

Water entered the Extravehicular Mobility Unit (EMU) helmet during extravehicular activity (EVA) no. 23 aboard the International Space Station on July 16, 2013, resulting in the termination of the EVA approximately 1 hour after it began. It was estimated that 1.5 liters of water had migrated up the ventilation loop into the helmet, adversely impacting the astronaut's hearing, vision, and verbal communication. Subsequent on-board testing and ground-based test, tear-down, and evaluation of the affected EMU hardware components determined that the proximate cause of the mishap was blockage of all water separator drum holes with a mixture of silica and silicates. The blockages caused a failure of the water separator degassing function, which resulted in EMU cooling water spilling into the ventilation loop, migrating around the circulating fan, and ultimately pushing into the helmet. The root cause of the failure was determined to be ground-processing shortcomings of the Airlock Cooling Loop Recovery (ALCLR) Ion Filter Beds, which led to various levels of contaminants being introduced into the filters before they left the ground. Those contaminants were thereafter introduced into the EMU hardware on-orbit during ALCLR scrubbing operations. This paper summarizes the failure analysis results along with identified process, hardware, and operational corrective actions that were implemented as a result of findings from this investigation.

Steele, John↗

Phase-field Simulation of Void Migration in a Temperature Gradient

We present a phase-field model that simulates vacancy diffusion in a solid with a strong inhomogeneity of vacancy mobility, which is used to study void migration via bulk and surface diffusion in a temperature gradient. The simulation results demonstrate that voids migrate up the temperature gradient and the migration velocity varies inversely with the void size in agreement with theory. The simulations also show the capability of the developed model for investigating the effect of surface diffusion, temperature gradient, and vacancy concentration on the void migration velocity and which are shown in this study. A potential application of the model is shown in studying the kinetics of the void migration and the formation of central hole in the nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Structural, Optical and Electrical Properties of PbSe Nanocrystal Solids Treated Thermally or with Simple Amines

We describe the structural, optical, and electrical properties of films of spin-cast, oleate-capped PbSe nanocrystals that are treated thermally or chemically in solutions of hydrazine, methylamine, or pyridine to produce electronically coupled nanocrystal solids. Postdeposition heat treatments trigger nanocrystal sintering at {approx}200 C, before a substantial fraction of the oleate capping group evaporates or pyrolyzes. The sintered nanocrystal films have a large hole density and are highly conductive. Most of the amine treatments preserve the size of the nanocrystals and remove much of the oleate, decreasing the separation between nanocrystals and yielding conductive films. X-ray scattering, X-ray photoelectron and optical spectroscopy, electron microscopy, and field-effect transistor electrical measurements are used to compare the impact of these chemical treatments. We find that the concentration of amines adsorbed to the NC films is very low in all cases. Treatments in hydrazine in acetonitrile remove only 2-7% of the oleate yet result in high-mobility n-type transistors. In contrast, ethanol-based hydrazine treatments remove 85-90% of the original oleate load. Treatments in pure ethanol strip 20% of the oleate and create conductive p-type transistors. Methylamine- and pyridine-treated films are also p-type. These chemically treated films oxidize rapidly in air to yield, after short air exposures, highly conductive p-type nanocrystal solids. Our results aid in the rational development of solar cells based on colloidal nanocrystal films.

36 MATERIALS SCIENCE↗

Influence of Gaussian disorder and exponential traps on charge carriers transport and recombination in single layer polymer light-emitting diodes based on PFO as emitting layer

In this paper, we study the transport and recombination mechanisms of charge carriers in a single layer PLED device based on PFO as emitting layer with considering Gaussian disorder, exponential distribution of traps, Poole–Frankel type field dependent hopping mobility and field independent effective transport hopping energy models. For this purpose, we use the one-dimensional and time-independent drift–diffusion model for simulation of electrical and optical characteristics of the PFO based PLED devices such as current density–luminance–voltage (J–L–V), recombination rate and singlet exciton density profile in steady-state and room temperature conditions. Also, we study the influence of the characteristic temperature and density of electron traps on the performance of devices at different voltages. Another topic is analyzing the current density–voltage characteristics of uni-polar devices (hole only or electron only) by using the well known expressions for trap-limited current and space charge-limited current and comparing them with simulation results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Critical review of electrical conductivity measurements and charge distribution analysis of magnesium oxide

The electrical conductivity sigma of MgO single crystals shows a sharp increase at 500-800 C, in particular of sigma surface, generally attributed to surface contamination. Charge Distribution Analysis (CDA), a new technique providing information on fundamental properties that was previously unavailable, allows for the determination of surface charges, their sign and associated internal electric field. Data on 99.99% purity, arc-fusion grown MgO crystals show that mobile charge carriers start to appear in the bulk of the MgO crystals between 200 and 400 C when sigma (measured by conventional techniques) is in t he 10(exp -14) to 10(exp -16) /omega/cm range. Above 500 C, as sigma increases to 10(exp -6) to 10(exp -7)/omega/cm, more charges appear giving rise to a strong positive surface charge supported by a strong internal field. This indicates that charges are generated in the bulk and diffuse to the surface by an internally controlled process. On the basis of their positive sign they are identified as holes (defect electrons). Because of the low cation content of these very pure MgO crystals, theses holes cannnot be associated with transition metal impurties. Instead, they are associated with the O(2-) sublattice, e.g. consist of O(-) states or positive holes. This conclusion is supported by magnetic susceptibility data showing the appearance of 1000 +/- 500 ppm paramagnetic species between 200-500 C. The magnetic data are consistent with strongly coupled, diamagnetic O(-) pairs below 200-500 C, chemically equivalent to peroxy anions, O2(2-), and probably associated with cation vacancies in the MgO matrix. The formation of O2(2-) in arc-fusion grown MgO crystals is very unexpected because of the highly reducing growth conditions. Their presence implies an internal redox reaction involving dissolved 'water' by which OH(-) pairs convert to O2(2-) plus H2 molecules. This redox conversion is supported by mass spectroscopic measurements of the H2 release from highly OH(-)-doped, finely divided MgO and by wet-chemical analysis of its oxidant concentration.

Freund, Friedemann↗

Incorporating Electrochemical Halide Oxidation into Drift-Diffusion Models to Explain Performance Losses in Perovskite Solar Cells under Prolonged Reverse Bias

Partial shading of a solar module can induce a set of cells within the module to operate under reverse bias. Studies have shown that metal halide perovskite solar cells with a wide variety of compositions and contacts exhibit interesting behavior in reverse bias that includes both reversible performance loss and non-reversible degradation. In this paper, an advanced drift-diffusion approach incorporating an electrochemical term to explain the short-circuit, open circuit and fill factor losses that are experimentally measured after prolonged reverse bias is used. It is shown that holes can tunnel into the perovskite due to sharp band bending near the contact, accumulate within the bulk of the perovskite absorber, and trigger the oxidation of halides to form neutral halogens. The density of neutral halogens is much higher in reverse bias because there are hardly any electrons available to reduce the iodine. The resulting halogens act as bulk recombination centers. While the interstitial halogen density does decay when the cell is operated in forward bias, permanent degradation can occur if the iodine diffuses out of the perovskite layer. Finally, the ways in which changing parameters such as the mobile ion density or the series resistance at the contact can influence device performance and stability are discussed.

degradation↗

The Locus of Free Charge-Carrier Generation in Solution-Cast Zn1–xMgxO/Poly(3-hexylthiophene) Bilayers for Photovoltaic Applications

The photoconductivity of solution-cast Zn 1–x Mg x O (x=0-0.4) and poly(3-hexylthiophene) (P3HT) thin films, and Zn 1-x Mg x O/P3HT bilayers is investigated using Time-Resolved Microwave Conductivity (TRMC) with the aim of determining the locus of free charge carrier generation in the bilayer system. The photoconductivity of Zn 1-x Mg x O thin films, under illumination with 300 nm laser pulses, is limited by the formation of stable excitons and by scattering of the carriers at grain boundaries. The electron mobility in Zn 1–x Mg x O films decreases exponentially with Mg concentration, up to x=0.4. In agreement with previous work, free carriers are observed in the P3HT film under illumination with 500 nm pulses in the absence of an acceptor. Under illumination with 500 nm pulses, where only the polymer absorbs, the TRMC signal for the Zn 1-x Mg x O/P3HT bilayers for x≥0.2 is the same as that of pure P3HT, indicating that free carrier generation in these bilayers occurs predominately by exciton dissociation in the polymer bulk, and not at the interface between the polymer and the solution-cast oxide. At lower Mg concentrations (x<0.2) the TRMC signal increases with decreasing x following the dependence of the electron mobility in the oxide but its light intensity dependence remains consistent with free carrier generation in the polymer bulk. To explain these results and previously published photovoltaic device data (Adv. Funct. Mater. 2007, 17, 264) we propose that free carrier generation in the bilayers predominantly occurs in the bulk of P3HT, and is followed by electron injection to the oxide to yield photocurrent in photovoltaic cells. The dependence of the TRMC signal of the bilayers on Mg concentration is explained in terms of the yield for free carrier generation in the polymer and the relative contributions of electrons in the oxide and holes in the polymer.

14 SOLAR ENERGY↗

Revealing the intrinsic transport properties of antiperovskite Sr 3 SnO thin films

A topologically non-trivial band structure and reports of superconductivity have motivated significant investigation into the transport properties of the antiperovskite oxide Sr 3 SnO. Phase-pure films of Sr 3 SnO can be grown by molecular beam epitaxy, but they do not have the required extremely high hole-doping densities (>1 × 10 21 cm –3 ) for which superconductivity has been observed in bulk materials. To date, high hole-doping densities have been achieved via inducing strontium deficiency, which inevitably results in impurity phases. Here, we show that indium acts as an effective hole dopant in Sr 3 SnO and can be used to achieve high hole doping densities in stoichiometric films. Films with carrier densities as high as 1.5 × 10 21 cm –3 remain non-superconducting. We, therefore, suggest that Sr 3 SnO is probably not an intrinsic superconductor. A second question addressed in this work is the measurement of the intrinsic electrical transport properties of Sr 3 SnO, given its rapid degradation in air. We show that even in inert atmospheres, reducing the time needed for establishing electrical contacts and protecting the Sr 3 SnO film result in improved electrical properties. Here, we demonstrate low carrier density films (4 × 10 18 cm –3 ) with carrier mobilities of 400 cm 2 V –1 s –1 at 10 K.

36 MATERIALS SCIENCE↗

The Characterization and Optimization of GaN Cap Layers and SiN Cap Layers on AlGaN/GaN HEMT Structures Grown on 200 mm GaN on Silicon

We have studied capping layers for AlGaN‐based high electron mobility transistor (HEMT) structures, looking at different thicknesses of GaN, SiN, and GaN + SiN caps. SiN capping has no effect on the sheet resistance of the layers, as expected from a high quality amorphous passivation layer. GaN cap layers increase the sheet resistance whether combined with a SiN cap or not, a consequence of the polarisation charge present at the GaN/AlGaN interface. For both GaN and SiN caps on their own, we get excellent morphology from only 2 nm thickness, with no degradation for layers up to 10 nm thick. For GaN + SiN caps, we have a speckled morphology with lots of small holes, which transmission electron microscopy (TEM) analysis showed to be linked to holes created in the GaN layers before the deposition of SiN layers. We attribute this to the roughening effect of silane on GaN layers, known in the literature. Upon processing SiN capped and GaN + SiN capped layers into HEMT based heterojunction diode devices, the two have equivalent forward current, but GaN + SiN capping has greatly increased reverse current. We conclude that GaN + SiN is not an appropriate capping layer for AlGaN HEMT based diodes, compared with high quality in situ SiN passivation directly grown on the AlGaN.

Charles, Matthew↗

Improved hybrid solar cells via in situ UV-polymerization.

One approach for making inexpensive inorganic-organic hybrid photovoltaic (PV) cells is to fill highly ordered TiO{sub 2} nanotube (NT) arrays with solid organic hole conductors such as conjugated polymers. Here, a new in situ UV polymerization method for growing polythiophene (UV-PT) inside TiO{sub 2} NTs is presented and compared to the conventional approach of infiltrating NTs with pre-synthesized polymer. A nanotubular TiO{sub 2} substrate is immersed in a 2,5-diiodothiophene (DIT) monomer precursor solution and then irradiated with UV light. The selective UV photodissociation of the C-I bond produces monomer radicals with intact {pi}-ring structure that further produce longer oligothiophene/PT molecules. Complete photoluminescence quenching upon UV irradiation suggests coupling between radicals created from DIT and at the TiO{sub 2} surface via a charge transfer complex. Coupling with the TiO{sub 2} surface improves UV-PT crystallinity and {pi}-{pi} stacking; flat photocurrent values show that charge recombination during hole transport through the polymer is negligible. A non-ideal, backside-illuminated setup under illumination of 620-nm light yields a photocurrent density of {approx} 5 {micro}A cm{sup -2} - surprisingly much stronger than with comparable devices fabricated with polymer synthesized ex situ. Since in this backside architecture setup we illuminate the cell through the Ag top electrode, there is a possibility for Ag plasmon-enhanced solar energy conversion. By using this simple in situ UV polymerization method that couples the conjugated polymer to the TiO{sub 2} surface, the absorption of sunlight can be improved and the charge carrier mobility of the photoactive layer can be enhanced.

14 SOLAR ENERGY↗

Modeling the Charge and Exciton Distributions in Phosphorescent White Organic Light-Emitting Diodes

A comprehensive numerical model is developed to quantitatively analyze the charge and exciton distributions in phosphorescent white organic light emitting diodes (WOLEDs). The model encompasses bipolar charge drift-diffusion transport with doping-dependent charge mobilities, field-dependent charge hopping across multiple interfaces, exciton generation, diffusion, energy transfer, radiative decay, and non-radiative exciton annihilation. The model is validated by direct measurement of the exciton distribution in monochromatic phosphorescent OLEDs. It is then applied to complex, multilayer WOLEDs where it is used to accurately predict their intensity and current-dependent spectral shifts. The magnitudes of different exciton loss channels in WOLEDs are calculated and quantitatively compared. This model provides an alternative for the many experimental iterations commonly used to optimize the color balance of complex OLEDs. In this context, the model inspired the addition of a hole blocking layer in the WOLED to balance the charge conduction and reduce spectral shifts – a design that is verified by experiment.

42 ENGINEERING↗

Space Suit Electrocardiographic Electrode Selection: Are commercial electrodes better than the old Apollo technology?

The NASA Manned Space Program uses an electrocardiograph (ECG) system to monitor astronauts during extravehicular activity (EVA). This ECG system, called the Operational Bioinstrumentation System (OBS), was developed during the Apollo era. Throughout the Shuttle program these electrodes experienced failures during several EVAs performed from the Space Shuttle and International Space Station (ISS) airlocks. An attempt during Shuttle Flight STS-109 to replace the old electrodes with new commercial off-the-shelf (COTS) disposable electrodes proved unsuccessful. One assumption for failure of the STS-109 COTS electrodes was the expansion of trapped gases under the foam electrode pad, causing the electrode to be displaced from the skin. Given that our current electrodes provide insufficient reliability, a number of COTS ECG electrodes were tested at the NASA Altitude Manned Chamber Test Facility. Methods: OBS disposable electrodes were tested on human test subjects in an altitude chamber simulating an Extravehicular Mobility Unit (EMU) operating pressure of 4.3 psia with the following goals: (1) to confirm the root cause of the flight certified, disposable electrode failure during flight STS-109. (2) to identify an adequate COTS replacement electrode and determine if further modifications to the electrodes are required. (3) to evaluate the adhesion of each disposable electrode without preparation of the skin with isopropyl alcohol. Results: There were several electrodes that failed the pressure testing at 4.3psia, including the electrodes used during flight STS-109. Two electrodes functioned well throughout all testing and were selected for further testing in an EMU at altitude. A vent hole placed in all electrodes was also tested as a possible solution to prevent gas expansion from causing electrode failures. Conclusions: Two failure modes were identified: (1) foam-based porous electrodes entrapped air bubbles under the pad (2) poor adhesion caused some electrodes to fail

Redmond, M.↗

Polaron Stabilization by Cooperative Lattice Distortion and Cation Rotations in Hybrid Perovskite Materials

Solution-processed organometallic perovskites have rapidly developed into a top candidate for the active layer of photovoltaic devices. In spite of the remarkable progress associated with perovskite materials, many questions about the fundamental photophysical processes taking place in these devices, remain open. High on the list of unexplained phenomena are very modest mobilities despite low charge carrier effective masses. Moreover, experiments elucidate unique degradation of photocurrent affecting stable operation of perovskite solar cells. These puzzles suggest that, while ionic hybrid perovskite devices may have efficiencies on par with conventional Si and GaAs devices, they exhibit more complicated charge transport phenomena. We report the results from an in-depth computational study of small polaron formation, electronic structure, charge density, and reorganization energies using both periodic boundary conditions and isolated structures. Using the hybrid density functional theory, we found that volumetric strain in a CsPbI 3 cluster creates a polaron with binding energy of around 300 and 900 meV for holes and electrons, respectively. In the MAPbI 3 (MA = CH 3 NH 3 ) cluster, both volumetric strain and MA reorientation effects lead to larger binding energies at around 600 and 1300 meV for holes and electrons, respectively. Such large reorganization energies suggest appearance of small polarons in organometallic perovskite materials. Furthermore, the fact that both volumetric lattice strain and MA molecular rotational degrees of freedom can cooperate to create and stabilize polarons indicates that in order to mitigate this problem, formamidinium (FA = HC(NH 2 ) 2 ) and cesium (Cs) based crystals and alloys, are potentially better materials for solar cell and other optoelectronic applications.

36 MATERIALS SCIENCE↗

Aggregation control in natural brush-printed conjugated polymer films and implications for enhancing charge transport

Shear-printing of electroactive polymers using natural brushes is a promising film deposition technique for printed electronics capable of microstructure control and electrical properties enhancement over large areas. Nevertheless, the interplay between film printing parameters, microstructure development, and charge transport is not well-understood. We report that natural brush-printing greatly enhances charge transport by as much as 5.7× through control of polymer nanofibril aggregate growth and backbone alignment, attributable to the oriented squamae of the natural hair. However, while brush shear-induced aggregation enhances charge transport, we show that backbone alignment alone does not guarantee charge transport anisotropy. These results provide additional understanding of shear-induced enhanced charge transport and set processing guidelines for high-performance printed organic circuitry.

natural brush-printing↗

Robotic Ankle for Omnidirectional Rock Anchors

Future robotic exploration of near-Earth asteroids and the vertical and inverted rock walls of lava caves and cliff faces on Mars and other planetary bodies would require a method of gripping their rocky surfaces to allow mobility without gravitational assistance. In order to successfully navigate this terrain and drill for samples, the grippers must be able to produce anchoring forces in excess of 100 N. Additionally, the grippers must be able to support the inertial forces of a moving robot, as well gravitational forces for demonstrations on Earth. One possible solution would be to use microspine arrays to anchor to rock surfaces and provide the necessary load-bearing abilities for robotic exploration of asteroids. Microspine arrays comprise dozens of small steel hooks supported on individual suspensions. When these arrays are dragged along a rock surface, the steel hooks engage with asperities and holes on the surface. The suspensions allow for individual hooks to engage with asperities while the remaining hooks continue to drag along the surface. This ensures that the maximum possible number of hooks engage with the surface, thereby increasing the load-bearing abilities of the gripper. Using the microspine array grippers described above as the end-effectors of a robot would allow it to traverse terrain previously unreachable by traditional wheeled robots. Furthermore, microspine-gripping robots that can perch on cliffs or rocky walls could enable a new class of persistent surveillance devices for military applications. In order to interface these microspine grippers with a legged robot, an ankle is needed that can robotically actuate the gripper, as well as allow it to conform to the large-scale irregularities in the rock. The anchor serves three main purposes: deploy and release the anchor, conform to roughness or misalignment with the surface, and cancel out any moments about the anchor that could cause unintentional detachment. The ankle design contains a rotary DC motor that can drag the microspine arrays across the surface to engage them with asperities, as well as a linear actuator to disengage the hooks from the surface. Additionally, the ankle allows the gripper to rotate freely about all three axes so that when the robot takes a step, the gripper may optimally orient itself with respect to the wall or ground. Finally, the ankle contains some minimal elasticity, so that between steps, the gripper returns to a default position that is roughly parallel to the wall.

Parness, Aaron↗