Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GPS data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

High-Altitude MMIC Sounding Radiometer for the Global Hawk Unmanned Aerial Vehicle

Microwave imaging radiometers operating in the 50-183 GHz range for retrieving atmospheric temperature and water vapor profiles from airborne platforms have been limited in the spatial scales of atmospheric structures that are resolved not because of antenna aperture size, but because of high receiver noise masking the small variations that occur on small spatial scales. Atmospheric variability on short spatial and temporal scales (second/ km scale) is completely unresolved by existing microwave profilers. The solution was to integrate JPL-designed, high-frequency, low-noise-amplifier (LNA) technology into the High-Altitude MMIC Sounding Radiometer (HAMSR), which is an airborne microwave sounding radiometer, to lower the system noise by an order of magnitude to enable the instrument to resolve atmospheric variability on small spatial and temporal scales. HAMSR has eight sounding channels near the 60-GHz oxygen line complex, ten channels near the 118.75-GHz oxygen line, and seven channels near the 183.31-GHz water vapor line. The HAMSR receiver system consists of three heterodyne spectrometers covering the three bands. The antenna system consists of two back-to-back reflectors that rotate together at a programmable scan rate via a stepper motor. A single full rotation includes the swath below the aircraft followed by observations of ambient (roughly 0 C in flight) and heated (70 C) blackbody calibration targets located at the top of the rotation. A field-programmable gate array (FPGA) is used to read the digitized radiometer counts and receive the reflector position from the scan motor encoder, which are then sent to a microprocessor and packed into data files. The microprocessor additionally reads telemetry data from 40 onboard housekeeping channels (containing instrument temperatures), and receives packets from an onboard navigation unit, which provides GPS time and position as well as independent attitude information (e.g., heading, roll, pitch, and yaw). The raw data files are accessed through an Ethernet port. The HAMSR data rate is relatively low at 75 kbps, allowing for real-time access over the Global Hawk high-data-rate downlink. Once on the ground, the raw data are unpacked and processed through two levels of processing. The Level 1 product contains geo-located, time-stamped, calibrated brightness temperatures for the Earth scan. These data are then input to a lD variational retrieval algorithm to produce temperature, water vapor, and cloud liquid water profiles, as well as several derived products such as potential temperature and relative humidity.

Brown, Shannon T.↗
DOE OSTI2025

An Open-Access Repository of Synchrophasor Data Quality Examples: Curation and Example Applications

Synchrophasor measurements are critical in providing wide-area situational awareness to power system operators. However, data artifacts may be introduced due to various issues such as loss of communication, loss of GPS signal, internal clock error, and vendor-specific implementation of phasor estimation algorithms. Tools designed to provide actionable insights from synchrophasor data, hence, must be designed to be robust to these data quality issues. In this work, two years of synchrophasor data sourced from multiple electric utilities in the United States were analyzed to identify examples of data quality problems. These examples were then labeled and published in the Grid Event Signature Library, a publicly available repository of power system measurements hosted by the Oak Ridge National Laboratory. This paper describes the data curation process, and illustrates two application use cases where the dataset can be valuable to the research community. In the first use case, a random forest classifier is trained to distinguish power system disturbance signatures from data anomalies introduced in synchrophasor measurements due to clock errors. The second use case studies the impact of data quality issues on an example synchrophasor application (specifically, event start time determination). The choice of data quality problems investigated is informed by the examples in the repository curated in this work.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2016

Navigation Architecture for a Space Mobile Network

The Tracking and Data Relay Satellite System (TDRSS) Augmentation Service for Satellites (TASS) is a proposed beacon service to provide a global, space based GPS augmentation service based on the NASA Global Differential GPS (GDGPS) System. The TASS signal will be tied to the GPS time system and usable as an additional ranging and Doppler radiometric source. Additionally, it will provide data vital to autonomous navigation in the near Earth regime, including space weather information, TDRS ephemerides, Earth Orientation Parameters (EOP), and forward commanding capability. TASS benefits include enhancing situational awareness, enabling increased autonomy, and providing near real-time command access for user platforms. As NASA Headquarters' Space Communication and Navigation Office (SCaN) begins to move away from a centralized network architecture and towards a Space Mobile Network (SMN) that allows for user initiated services, autonomous navigation will be a key part of such a system. This paper explores how a TASS beacon service enables the Space Mobile Networking paradigm, what a typical user platform would require, and provides an in-depth analysis of several navigation scenarios and operations concepts. This paper provides an overview of the TASS beacon and its role within the SMN and user community. Supporting navigation analysis is presented for two user mission scenarios: an Earth observing spacecraft in low earth orbit (LEO), and a highly elliptical spacecraft in a lunar resonance orbit. These diverse flight scenarios indicate the breadth of applicability of the TASS beacon for upcoming users within the current network architecture and in the SMN.

Data Relay↗
NASA NTRS2022

Searching for Quasi-periodic Oscillations in Astrophysical Transients Using Gaussian Processes

Analyses of quasi-periodic oscillations(QPOs)are important to understanding the dynamic behavior in manyastrophysical objects during transient events like gamma-ray bursts, solarflares, magnetarflares, and fast radiobursts. Astrophysicists often search for QPOs with frequency-domain methods such as(Lomb–Scargle)periodograms, which generally assume power-law models plus some excess around the QPO frequency. Time-series data can alternatively be investigated directly in the time domain using Gaussian process(GP)regression.While GP regression is computationally expensive in the general case, the properties of astrophysical data andmodels allow fast likelihood strategies. Heteroscedasticity and nonstationarity in data have been shown to causebias in periodogram-based analyses. GPs can take account of these properties. Using GPs, we model QPOs as astochastic process on top of a deterministicflare shape. Using Bayesian inference, we demonstrate how to infer GPhyperparameters and assign them physical meaning, such as the QPO frequency. We also perform model selectionbetween QPOs and alternative models such as red noise and show that this can be used to reliablyfind QPOs. Thismethod is easily applicable to a variety of different astrophysical data sets. We demonstrate the use of this methodon a range of short transients: a gamma-ray burst, a magnetarflare, a magnetar giantflare, and simulated solarflare data.

Moritz Hubner↗
NASA NTRS1990

Towards GPS orbit accuracy of tens of centimeters

In this paper, CASA Uno orbit results are presented utilizing data from four continents. Refinements in orbit modeling, combined with the availability of a worldwide tracking network and the dense distribution of tracking sites in North and South America, have improved orbit determination precision to about 60 cm (per component) for four of the seven GPS satellites tracked in CASA Uno. The orbit results are consistent with California baseline repeatabilities, which are at the few mm level in horizontal and length, and 1-2 cm in the vertical. Baseline comparisons with VLBI provide a measure of orbit accuracy, showing sub-cm agreement in length and 1.5 cm agreement in the horizontal.

Lichten, Stephen M.↗
NASA NTRS2000

Using Airborne Laser Altimetry to Detect Topographic Change at Long Valley Caldera California

The topography of the Long Valley caldera, California, was sampled using airborne laser altimetry in 1993, 1995, and 1997 to test the feasibility of using airborne laser altimetry for monitoring deformation of volcanic origin. Results show the laser altimeters are able to resolve subtle topographic features such as a gradual slope and to detect small transient changes in lake elevation. Crossover and repeat pass analyses of laser tracks indicate decimeter-level vertical precision is obtained over flat and low-sloped terrain for altimeter systems performing waveform digitization. Comparisons with complementary, ground-based CPS data at a site close to Bishop airport indicate that the laser and GPS-derived elevations agree to within the error inherent in the measurement and that horizontal locations agree to within the radius of the laser footprint. A comparison of the data at two sites, one where no change and the other where the maximum amount of vertical uplift is expected, indicates approximately 10 cm of relative uplift occurred 1993-1997, in line with predictions from continuous CPS measurements in the region. Extensive terrain mapping flights during the 1995 and 1997 missions demonstrate some of the unique abilities of laser altimetry; the straightforward creation of high resolution, high accuracy digital elevation models of overflown terrain, and the ability to determine ground topography in the presence of significant ground cover such as dense tree canopies. These capabilities make laser altimetry an attractive technique for quantifying topographic change of volcanic origin, especially in forested regions of the world where other remote sensing instruments have difficulty detecting the underlying topography.

Hofton, M. A.↗
NASA NTRSDate not supplied

Topographic Quintet: Comparing Five Methods for Measuring Ultra-High Resolution Topography

We compare different methods for collecting ultra-high resolution topography data within an analog planetary, human landing site scale area. Our aim is to investigate the cost and benefits of different 3D terrain mapping techniques, their associated data collection methods, and how their different specifications (e.g., range, spatial resolution, scanning-time, mobility, operating constraints, GPS-Denied operation, etc.) might be applied to landing-site characterization and mission operations. We compare 3D terrain data collected during a field campaign in November 2021 from an outcrop at Kilbourne Hole in southern New Mexico using different Light Detection and Ranging (LiDAR) sensors on the ground and stereo-derived 3D data from framing cameras mounted on small uncrewed aerial systems (sUAS).Our foci for this experiment are ground-based, surveying, and autonomous vehicle-type 3D scanning sensors that might be used for planetary surface exploration from landed assets (e.g., lander, rover, astronaut-mounted sensors, decent imaging, hoppers, or drones).[e.g. 1]This test is not meant to benchmark these scanners against one another, nor provide a recommendation for a specific make or model. Rather, our goal is to quantify time, effort, resolution, and operational trade-offs that are important for selecting a topographic instrument/methodology for a given scope of terrain characterization. Our results indicate that each technique is capable of exceptional quality terrain characterization for planetary exploration and scientific inquiry, but we hypothesize the appropriate technique is highly dependent on the scope of operational specifications and science requirements.

P Whelley↗
NASA NTRS1995

TOPEX/Poseidon Precision Orbit Determination Using Combined GPS, SLR, and DORIS

TOPEX/Poseidon (T/P) is a joint spaceborne oceanographic mission of U.W. NASA and France CNES design launched August 10, 1992. The satellite has a variety tracking systems for both operational and precision orbit determination. Three precise tracking systems: Satellite Laser Ranging (SLR), Doppler Orbitography and Radiopositioning Integrated by Satellite (DORIS), and Global Positioning System (GPS) provide high quality measurements essential for reconstructing the T/P orbital height with centimeter precision. This paper presents results of simultaneously processing all three data types to exploit the inherent strength of each in a combined solution. SLR and DORIS are routinely combined to provide orbit solutions for the T/P science team. GPS orbit solutions are produced as part of the first demonstration flight of a high quality spaceborne GPS receiver. Coordinate frame and software system differences between the combined SLR/DORIS orbits and the GPS orbits induce orbital height differences of 2 to 3 centimeters. Combining the three data types within a single software system permits removal of software system differences while obtaining coordinate frame calibration information. These calibrations will aid future spaceborne GPS missions that are not complemented with SLR and/or DORIS.

TOPEX/Poseidon↗
NASA NTRS1994

Time and position accuracy using codeless GPS

The Global Positioning System has allowed scientists and engineers to make measurements having accuracy far beyond the original 15 meter goal of the system. Using global networks of P-Code capable receivers and extensive post-processing, geodesists have achieved baseline precision of a few parts per billion, and clock offsets have been measured at the nanosecond level over intercontinental distances. A cloud hangs over this picture, however. The Department of Defense plans to encrypt the P-Code (called Anti-Spoofing, or AS) in the fall of 1993. After this event, geodetic and time measurements will have to be made using codeless GPS receivers. However, there appears to be a silver lining to the cloud. In response to the anticipated encryption of the P-Code, the geodetic and GPS receiver community has developed some remarkably effective means of coping with AS without classified information. We will discuss various codeless techniques currently available and the data noise resulting from each. We will review some geodetic results obtained using only codeless data, and discuss the implications for time measurements. Finally, we will present the status of GPS research at JPL in relation to codeless clock measurements.

Dunn, C. E.↗
DOE OSTI2026

Outdoor Deployment Data for a Four-Terminal GaAs//Si Tandem Solar Mini-Module

This dataset contains the complete outdoor measurement and analysis data for a mechanically stacked, four-terminal (4T) gallium arsenide (GaAs)//silicon (Si) tandem solar mini-module deployed from October 2019 to January 2021 at the Solar Radiation Research Laboratory (SRRL) in Golden, Colorado, USA. The data support a performance modeling and degradation analysis framework for tandem photovoltaic devices, as described in the accompanying publication. The dataset includes: (1) current–voltage (J–V) characteristics of each sub-cell measured approximately every five minutes, with extracted performance parameters; (2) spectral irradiance from an EKO MS-710 WISER spectroradiometer, along with derived spectral mismatch ratios (SMR) and average photon energy (APE); (3) one-minute resolution meteorological data from the co-located SRRL weather station and GPS-derived precipitable water vapor (PWV); (4) pre-deployment laboratory characterization (external quantum efficiency, J–V curves, standard test conditions parameters); (5) outdoor-extracted temperature and PWV correction coefficients; and (6) PVcircuit equivalent-circuit simulation outputs used for model validation. Degradation rates of −4.1 ± 0.2 %/year (GaAs) and −2.5 ± 0.9 %/year (Si) were determined using a filtering and normalization methodology adapted for fixed-tilt tandem modules. All data are provided in open, portable formats (Apache Parquet, CSV, JSON) to enable full reproducibility of the published analysis.

14 SOLAR ENERGY↗
NASA NTRS2016

Navigation Architecture For A Space Mobile Network

The Tracking and Data Relay Satellite System (TDRSS) Augmentation Service for Satellites (TASS) is a proposed beacon service to provide a global, space-based GPS augmentation service based on the NASA Global Differential GPS (GDGPS) System. The TASS signal will be tied to the GPS time system and usable as an additional ranging and Doppler radiometric source. Additionally, it will provide data vital to autonomous navigation in the near Earth regime, including space weather information, TDRS ephemerides, Earth Orientation Parameters (EOP), and forward commanding capability. TASS benefits include enhancing situational awareness, enabling increased autonomy, and providing near real-time command access for user platforms. As NASA Headquarters Space Communication and Navigation Office (SCaN) begins to move away from a centralized network architecture and towards a Space Mobile Network (SMN) that allows for user initiated services, autonomous navigation will be a key part of such a system. This paper explores how a TASS beacon service enables the Space Mobile Networking paradigm, what a typical user platform would require, and provides an in-depth analysis of several navigation scenarios and operations concepts.

Satellite↗
DOE OSTI2021

A Deterministic Multivariate Clustering Method for Drive Cycle Generation from In-Use Vehicle Data

Accurately characterizing vehicle drive cycles plays a fundamental role in assessing the performance of new vehicle technologies. Repeatable, short duration representative drive cycles facilitate more informed decision making, resulting in improved test procedures and more successful vehicle designs. With continued growth in the deployment of onboard telematics systems employing global positioning systems (GPS), large scale, low cost collection of real-world vehicle drive cycle data has become a reality. As a result of these technological advances, researchers, designers, and engineers are no longer constrained by lack of operating data when developing and optimizing technology, but rather by resources available for testing and simulation. Experimental testing is expensive and time consuming, therefore the need exists for a fast and accurate means of generating representative cycles from large volumes of real-world driving data. This paper explores the development and initial validation of a method of generating representative drive cycles from large collections of real-world vehicle data using a deterministic multivariate clustering approach. Starting with theory and diving into the methodology behind representative cycle generation, the paper aims to also present graphical and tabular results of initial validation via vehicle simulation and chassis dynamometer testing. Additional topics for further research and areas for ongoing development will also be presented.

47 OTHER INSTRUMENTATION↗
NASA NTRS2002

Preliminary Results of the GPS Flight Experiment on the High Earth Orbit AMSAT-OSCAR 40 Spacecraft

The GPS flight experiment on the High Earth Orbit (HEO) AMSAT-OSCAR 40 (AO-40) spacecraft was activated for a period of approximately six weeks between 25 September and 2 November, 2001, and the initial results have exciting implications for using GPS as a low-cost orbit determination sensor for future HEO missions. AO-40, an amateur radio satellite launched November 16, 2000, is currently in a low inclination, 1000 by 58,800 km altitude orbit. Although the GPS receiver was not initialized in any way, it regularly returned GPS observations from points all around the orbit. Raw signal to noise levels as high as 9 AMUs (Trimble Amplitude Measurement Units) or approximately 48 dB-Hz have been recorded at apogee, when the spacecraft was close to 60,000 km in altitude. On several occasions when the receiver was below the GPS constellation (below 20,000 krn altitude), observations were reported for GPS satellites tracked through side lobe transmissions. Although the receiver has not returned any point solutions, there has been at least one occasion when four satellites were tracked simultaneously, and this short arc of data was used to compute point solutions after the fact. These results are encouraging, especially considering the spacecraft is currently in a spin-stabilized attitude mode that narrows the effective field of view of the receiving antennas and adversely affects GPS tracking. Already AO-40 has demonstrated the feasibility of recording GPS observations in HEO using an unaided receiver. Furthermore, it is providing important information about the characteristics of GPS signals received by a spacecraft in a HEO, which has long been of interest to many in the GPS community. Based on the data returned so far, the tracking performance is expected to improve when the spacecraft is transitioned to a three axis stabilized, nadir pointing attitude in Summer, 2002.

Moreau, Michael C.↗
DOE OSTI2025

Compactly‐Supported Nonstationary Kernels for Computing Exact Gaussian Processes on Big Data

The Gaussian process (GP) is a widely used method for analyzing large-scale data sets, including spatio-temporal measurements of nonlinear processes that are now commonplace in the environmental sciences. Traditional implementations of GPs involve stationary kernels (also termed covariance functions) that limit their flexibility, and exact methods for inference that prevent application to data sets with more than about 10,000 points. Modern approaches to address stationarity assumptions generally fail to accommodate large data sets, while all attempts to address scalability focus on approximating the Gaussian likelihood, which can involve subjectivity and lead to inaccuracies. In this work, we explicitly derive an alternative kernel that can discover and encode both sparsity and nonstationarity. We embed the kernel within a fully Bayesian GP model and leverage high-performance computing resources to enable the analysis of massive data sets. We demonstrate the favorable performance of our novel kernel relative to existing exact and approximate GP methods across a variety of synthetic data examples. Furthermore, we conduct space–time prediction based on more than 1 million measurements of daily maximum temperature and verify that our results outperform state-of-the-art methods in the Earth sciences. More broadly, having access to exact GPs that use ultra-scalable, sparsity-discovering, nonstationary kernels allows GP methods to truly compete with a wide variety of machine learning methods.

Gaussian processes↗
NASA NTRS2004

Evaluation of Mobile Phone Interference With Aircraft GPS Navigation Systems

This report compiles and analyzes tests that were conducted to measure cell phone spurious emissions in the Global Positioning System (GPS) radio frequency band that could affect the navigation system of an aircraft. The cell phone in question had, as reported to the FAA (Federal Aviation Administration), caused interference to several GPS receivers on-board a small single engine aircraft despite being compliant with data filed at the time with the FCC by the manufacturer. NASA (National Aeronautics and Space Administration) and industry tests show that while there is an emission in the 1575 MHz GPS band due to a specific combination of amplifier output impedance and load impedance that induces instability in the power amplifier, these spurious emissions (i.e., not the intentional transmit signal) are similar to those measured on non-intentionally transmitting devices such as, for example, laptop computers. Additional testing on a wide sample of different commercial cell phones did not result in any emission in the 1575 MHz GPS Band above the noise floor of the measurement receiver.

Pace, Scott↗
DOE OSTI2023

Empirical evidence that mean soil contaminant concentration is not a conservative indicator of external exposure to wildlife

Adequate information on external exposure is often a limiting factor in ecological risk assessments because of a lack of exposure data for free-ranging animals as they interact with a heterogeneous distribution of contaminants. Instead, most wildlife exposure data are estimated from model simulations. However, empirical exposure data are rarely available to verify model results, or to test fundamental assumptions inherent in exposure assessments. We used novel, GPS-coupled radiation dosimeters on reindeer (Rangifer tarandus) to quantify their external exposure for five months in a Chernobyl fallout affected mountainous area of Norway. The exposure data were then used to test a fundamental assumption in screening-level risk assessments: Mean soil contaminant concentrations can be used to conservatively estimate chronic external exposures to representative animals. External exposure and GPS coordinates were obtained hourly and compared to model simulations of exposure based on airborne surveys of 137 Cs soil contamination. Our objectives were to determine 1) if modelled dose estimates based on mean 137 Cs soil concentrations were conservative, and 2) if modelled dose estimates could be improved by adjusting for spatial–temporal heterogeneity of contaminants using 137 Cs concentrations within reindeers’ GPS-defined home ranges and core areas. We found that external exposure modelled from mean soil contaminant concentrations underestimated exposure by 70% compared to empirical measurements from GPS-dosimeter collars worn on individual animals. Using area-weighted mean contaminant levels within the animals’ home range improved the model estimates, but still underestimated the field dosimeter data by 53%. The best estimate of external exposure was obtained when high-use areas within their home range, along with spatial heterogeneity of the contaminant, was accounted for by using area-weighted mean soil contaminant levels within GPS-derived core areas. Accounting for temporal use of core areas within animals’ home range provided a 24% improvement. Here, a comparison of our analyses to similar work performed on Chernobyl wolves found the two studies concur that risk assessors should be cautious in relying on the paradigm of using averaged soil contaminant levels to provide conservative estimates of external exposure to representative individuals. Results of modelled external exposure based on mean soil contaminant concentrations could misguide assessors and cause inappropriate management decisions.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2021

Libpanda: A High Performance Library for Vehicle Data Collection

Cyber-Physical Systems (CPS) generally involve time-critical components due to physical dynamics, therefore necessitating high-performance subsystems. This is also true in data collection scenarios to infer physical phenomena. This paper covers Libpanda as an example of a component that has been designed to address performance issues in CPS implementations. Libpanda is a C++ library that interfaces software with a Comma.ai Panda device. Pandas are used for installation in modern vehicles to read the vehicle CAN bus, providing rich sensor data and limited vehicle control through message injection. The motivation to design lib-panda stems from the lack of performance in Python-based code that runs on inexpensive hardware like a Raspberry Pi. In such situations, Python code would result in utilizing 92% CPU while also dropping around 40% of the CAN packet due to bottlenecks. Without using different tools, inconsistent data collection means a loss of time-based vehicle state interpretation. Libpanda addresses these issues through implementation in a different language and implementation of different design paradigms involving asynchronous calls and multithreading. The Panda also features a GPS module that allows multiple instances to synchronize clocks for large-scale data collection scenarios. Libpanda has been designed with time-synchronization in mind to aid in the measurement of inter-vehicle dynamics. The performance improvements of libpanda have resulted in it becoming an important component in automotive dynamics research that requires a higher technical performance in large-scale experiments.

Bunting, Matthew↗
NASA NTRS1980

ESTL RF communication simulators for orbiter payloads and GPS satellites

The simulator contains a transponder compatible with the NASA Spaceflight Tracking and Data Network, a transponder compatible with the DOD Space Ground Link System, and associated command detector units and telemetry multiplexer/modulators. It is pointed out that during selected ESTL tests, the actual payload transponder will be configured with the Payload Communications Simulator (PCS) telemetry multiplexer and modulators to form a complete payload communication system. A block diagram of the PCS is included.

Schmidt, O. L.↗