Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine emission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Experimental clean combustor program: Diesel no. 2 fuel addendum, phase 3

A CF6-50 engine equipped with an advanced, low emission, double annular combustor was operated 4.8 hours with No. 2 diesel fuel. Fourteen steady-state operating conditions ranging from idle to full power were investigated. Engine/combustor performance and exhaust emissions were obtained and compared to JF-5 fueled test results. With one exception, fuel effects were very small and in agreement with previously obtained combustor test rig results. At high power operating condition, the two fuels produced virtually the same peak metal temperatures and exhaust emission levels. At low power operating conditions, where only the pilot stage was fueled, smoke levels tended to be significantly higher with No. 2 diesel fuel. Additional development of this combustor concept is needed in the areas of exit temperature distribution, engine fuel control, and exhaust emission levels before it can be considered for production engine use.

Gleason, C. C.↗

HIGH-RESOLUTION CHANDRA HETG SPECTROSCOPY OF V404 CYGNI IN OUTBURST

As one of the best-characterized stellar-mass black holes, with good measurements of its mass, distance, and inclination, V404 Cyg is the ideal candidate to study Eddington-limited accretion episodes. After a long quiescent period, V404 Cyg underwent a new outburst in 2015 June. We obtained two Chandra HETG exposures of 20 and 25 ks. Many strong emission lines are observed; the ratio of Si He-like triplet lines gives an estimate for the formation region distance of 4 × 10{sup 11} cm. A narrow Fe Kα line is detected with an equivalent width greater than 1 keV in many epochs, signaling that we do not directly observe the central engine. Obscuration of the central engine and strong narrow emission lines signal that the outer disk may be illuminated, and its structure may help to drive the strong variability observed in V404 Cyg. In the highest flux phases, strong P-Cygni profiles consistent with a strong disk wind are observed, likely radiation or thermally driven as V404 Cyg approaches its Eddington limit. The kinetic power of this wind may be extremely high at >0.1 L{sub Bol}.

79 ASTRONOMY AND ASTROPHYSICS↗

Comparison of RCCI Operation with and without EGR over the Full Operating Map ofa Heavy-Duty Diesel Engine

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection of a higher reactivity fuel, otherwise known as Reactivity Controlled Compression Ignition (RCCI), has been shown as a method to achieve high efficiency combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions. A key requirement for extending to high-load operation is reduce the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and direct injection of diesel fuel. Natural gas/diesel RCCI engine operation is compared over the EPA Heavy-Duty 13 mode supplemental emissions test with and without EGR. Emissions and efficiency metrics were examined over the entire engine map for both operating modes. It was found that the use of EGR lowered combustion noise to less than 97 dBa and lowered the cycle averaged NOx emissions by 48%, with only a slight increase in soot and 0.5 point decrease in brake thermal efficiency. Thus, operation with EGR offered the lowest total fluid consumption when considering the use of a selective catalytic reduction system for NOx aftertreatment.

Hanson, Reed↗

Energy dissipation via acoustic emission in ductile crack initiation

In this article, we present a modeling approach to estimate the energy release due to ductile crack initiation in conjunction to the energy dissipation associated with the formation and propagation of transient stress waves typically referred to as acoustic emission. To achieve this goal, a ductile fracture problem is investigated computationally using the finite element method based on a compact tension geometry under Mode I loading conditions. To quantify the energy dissipation associated with acoustic emission, a crack increment is produced given a pre-determined notch size in a 3D cohesive-based extended finite element model. The computational modeling methodology consists of defining a damage initiation state from static simulations and linking such state to a dynamic formulation used to evaluate wave propagation and related energy redistribution effects. The model relies on a custom traction separation law constructed using full field deformation measurements obtained experimentally using the digital image correlation method. The amount of energy release due to the investigated first crack increment is evaluated through three different approaches both for verification purposes and to produce an estimate of the portion of the energy that radiates away from the crack source in the form of transient waves. The results presented herein propose an upper bound for the energy dissipation associated to acoustic emission, which could assist the interpretation and implementation of relevant nondestructive evaluation methods and the further enrichment of the understanding of effects associated with fracture.

42 ENGINEERING↗

Furniture wood wastes: Experimental property characterisation and burning tests

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CFD assessment of the carbon monoxide and nitric oxide formation from RD-170 hot-fire testing at MSFC

Computational Fluid Dynamics (CFD) technology has been used to assess the exhaust plume pollutant environment of the RD-170 engine hot-firing on the F1 Test Stand at Marshall Space Flight Center. Researchers know that rocket engine hot-firing has the potential for forming thermal nitric oxides (NOx), as well as producing carbon monoxide (CO) when hydrocarbon fuels are used. Because of the complicated physics involved, however, little attempt has been made to predict the pollutant emissions from ground-based engine testing, except for simplified methods which can grossly underpredict and/or overpredict the pollutant formations in a test environment. The objective of this work, therefore, has been to develop a technology using CFD to describe the underlying pollutant emission physics from ground-based rocket engine testing. This resultant technology is based on a three-dimensional, viscous flow, pressure-based CFD formulation, where wet CO and thermal NOx finite-rate chemistry mechanisms are solved with a Penalty function method.

Wang, Ten-See↗

Surrogate Model Development for Fuels for Advanced Combustion Engines

The fuels used in internal-combustion engines are complex mixtures of a multitude of different types of hydrocarbon species. Attempting numerical simulations of combustion of real fuels with all of the hydrocarbon species included is highly unrealistic. Thus, a surrogate model approach is generally adopted, which involves choosing a few representative hydrocarbon species whose overall behavior mimics the characteristics of the target fuel. The present study proposes surrogate models for the ninefuels for advanced combustion engines (FACE) that have been developed for studying low-emission, high-efficiency advanced diesel engine concepts. The surrogate compositions for the fuels are arrived at by simulating their distillation profiles to within a maximum absolute error of ~4% using a discrete multi-component (DMC) fuel model that has been incorporated in the multi-dimensional computational fluid dynamics (CFD) code, KIVA-ERC-CHEMKIN. The simulated surrogate compositions cover the range and measured concentrations of the various hydrocarbon classes present in the fuels. The fidelity of the surrogate fuel models is judged on the basis of matching their specific gravity, lower heating value, hydrogen/carbon (H/C) ratio, cetane number, and cetane index with the measured data for all nine FACE fuels.

33 ADVANCED PROPULSION SYSTEMS↗

The Engineering of Climate Engineering

While reducing anthropogenic greenhouse gas emissions remains the most essential element of any strategy to manage climate change risk, it is also in principle possible to directly cool the climate by reflecting some sunlight back to space. Possible such \climate engineering" approaches include adding aerosols to the stratosphere or marine cloud brightening. Assessing whether these ideas could reduce risk requires a broad multidisciplinary research eort spanning climate science, social sciences, and governance. However, if such strategies were ever used, the effort would also constitute one of the most critical engineering design and control challenges ever considered: making real-time decisions for a highly uncertain and nonlinear dynamic system with many input variables, many measurements, and vastly more internal degrees of freedom whose dynamics span a wide range of timescales. We provide a review of the engineering and design aspects of climate engineering, discussing both progress to date and remaining challenges that will need to be addressed.

climate engineering, climate modeling, geoengineer↗

DME-Propane Ignition Delay Time Measurements at Mixing Controlled Compression Ignition Engine-Relevant Conditions

The blend of dimethyl ether (DME, CH 3 OCH 3 ) and propane (C 3 H 8 ) is a potentially renewable fuel mixture that has the potential to replace diesel in compression ignition engines. The combination can potentially reduce particulate and greenhouse gas emissions compared to a conventional diesel engine operating under similar conditions. However, detailed conceptual and simulation studies must be conducted before adopting a new fuel on a compression ignition engine. For these simulations, accurate chemical kinetic models are necessary. However, the validity of chemical kinetic mechanisms in the literature is unknown for mixing controlled compression ignition (MCCI) engine operating conditions. Hence, in this work, we studied the ignition of dimethyl ether (DME) and propane blends in a shock tube at MCCI engine conditions. Ignition delay time (IDT) data was collected behind the reflected shock for DME-propane mixtures for heavy-duty compression ignition (CI) engine parameters. Undiluted experiments spanning temperatures of 700 to 1100 K and pressures of 55 to 84 bar for various blends (100% CH 3 OCH 3 / 0% C 3 H 8, 100% C 3 H 8 / 0% CH 3 OCH 3 , 60% CH 3 OCH 3 / 40% C 3 H 8 ) of DME and propane were combusted in synthetic air (21% O 2 / 79% N 2 ). Some experiments were conducted at higher pressures (90-120 bar) to understand model performance at these conditions. Comparisons of IDT were made with the predictions of recent chemical kinetic mechanisms for DME-propane mixture, including the Aramco3.0, NUIG, and Dames et al. mechanisms. All mechanisms overpredicted IDT compared to experimental values. Sensitivity analysis was conducted with Dames et al. model, and critical reactions sensitive to IDT of DME-propane mixture near 100 bar are outlined.

Mohammed, Zuhayr Pasha↗

Quiet Clean Short-haul Experimental Engine (QCSEE). Double-annular clean combustor technology development report

A sector combustor technology development program was conducted to define an advanced double annular dome combustor sized for use in the quiet clean short haul experimental engine (QCSEE). A design which meets the emission goals, and combustor performance goals of the QCSEE engine program was developed. Key design features were identified which resulted in substantial reduction in carbon monoxide and unburned hydrocarbon emission levels at ground idle operating conditions, in addition to very low nitric oxide emission levels at high power operating conditions. Their significant results are reported.

Bahr, D. W.↗

Highly Efficient Pure‐Blue Light‐Emitting Diodes Based on Rubidium and Chlorine Alloyed Metal Halide Perovskite

Abstract Perovskite light‐emitting diodes (PeLEDs) are promising candidates for display and solid‐state lighting, due to their tunable colors, high conversion efficiencies, and low cost. However, the performance of blue PeLEDs is far inferior to that of the near‐infrared, red, and green counterparts. Here, the fabrication of pure‐blue PeLEDs with an emission peak at 475 nm, a peak external quantum efficiency of 10.1%, and a maximum luminance of 14 000 cd m −2 is demonstrated by tailoring the compositions of perovskites. The pure‐blue electroluminescence is achieved by simultaneous addition of rubidium and chlorine ions into CsPbBr 3 and incorporation of phenylethylammonium chloride forms quasi‐2D hybrid perovskites. The combination of these composition engineering results in blueshifted emissions without reducing the quantum yield. The judicious alloying is shown to be critical to result in the better morphology with suppressed current leakage and enhanced light outcoupling.

Yang, Yang↗

Trends in Unconventional Well Development—Methane Emissions Associated with the Use of Dual Fuel and Dedicated Natural Gas Engines

Abstract The process of unconventional natural gas recovery is becoming increasingly popular as the world’s demand for alternative fuels continues to grow. Natural gas has the potential to be a widely used fuel in the near future due to its availability and potential to displace petroleum‐based liquid fuels. As energy companies extract natural gas, current fuels, such as diesel, are consumed in mass quantities for drilling and hydraulic fracturing operations. To save on costs, and in an attempt to reduce emissions, many companies are investing in dual fuel and dedicated natural gas engines to power these operations. This trend results in new sources of methane emissions, which can contribute significantly to global warming. We are aware of the potential impact of these emissions and are conducting research funded by the Department of Energy to assess methane emissions from dual fuel and dedicated natural gas technologies, as industry moves towards more extensive use of natural gas as a fuel for onsite power production.

Johnson, Derek↗

Advanced Natural Gas Reciprocating Engine(s)

Energy independence and fuel savings are hallmarks of the nation’s energy strategy. The advancement of natural gas reciprocating engine power generation technology is critical to the nation’s future. A new engine platform that meets the efficiency, emissions, fuel flexibility, cost and reliability/maintainability targets will enable American manufacturers to have highly competitive products that provide substantial environmental and economic benefits in the US and in international markets. Along with Cummins and Waukesha, Caterpillar participated in a multiyear cooperative agreement with the Department of Energy to create a 50% efficiency natural gas powered reciprocating engine system with a 95% reduction in NOx emissions by the year 2013. This platform developed under this agreement will be a significant contributor to the US energy strategy and will enable gas engine technology to remain a highly competitive choice, meeting customer cost of electricity targets, and regulatory environmental standard. Engine development under the Advanced Reciprocating Engine System (ARES) program was divided into phases, with the ultimate goal being approached in a series of incremental steps. This incremental approach would promote the commercialization of ARES technologies as soon as they emerged from development and would provide a technical and commercial foundation of later-developing technologies. Demonstrations of the Phase I and Phase II technology were completed in 2004 and 2008, respectively. Program tasks in Phase III included component and system development and testing from 2009-2012. Two advanced ignition technology evaluations were investigated under the ARES program: laser ignition and distributed ignition (DIGN). In collaboration with Colorado State University (CSU), a laser ignition system was developed to provide ignition at lean burn and high boost conditions. Much work has been performed in Caterpillar’s DIGN program under the ARES program. This work has consisted of both modeling and single cylinder engine experiments to quantify DIGN performance. The air handling systems of natural gas engines dissipate a percentage of available energy as a result of both flow losses and turbomachinery inefficiencies. An analytical study was initiated to increase compressor efficiency by employing a 2-stage inter-cooled compressor. Caterpillar also studied a turbo-compound system that employs a power turbine to recover energy from the exhaust gases for improved engine efficiency. Several other component and system investigations were undertaken during the final phase of the program to reach the ultimate ARES goals. An intake valve actuation system was developed and tested to improve engine efficiency, durability and load acceptance. Analytical modeling and materials testing were performed to evaluate the performance of steel pistons and compacted graphite iron cylinder head. Effort was made to improve the detonation sensing system by studying and comparing the performance of different pressure sensors. To reduce unburned hydrocarbon emissions, different camshafts were designed and built to investigate the effect of exhaust valve opening timing and value overlap. 1-D & 3-D coupled simulation was used to study intake and exhaust manifold dynamics with the goal of reducing load in-balance between cylinders. Selective catalytic reduction with on-board reductant generation to reduce NOx emissions was also engine tested. An effective mean to successfully deploy ARES technologies into the energy markets is to deploy demonstration projects in the field. In 2010, NETL and Caterpillar agreed to include a new “opportunity fuel” deliverable and two field demonstrations in the ARES program. An Organic Rankine Cycle system was designed with production intent incorporating lessons learned from the Phase II demonstration. Unfortunately, business conditions caused Caterpillar to cancel this demonstration in 2011. Nonetheless, Caterpillar partnered with a local dealer to deploy an ARES class engine using syngas from a biomass gasifier as the DE-FC26-01CH11079 primary combustion fuel in Gleason, TN. Upon the successful start-up and commissioning of the demonstration unit, ownership of the system was transferred to the dealer. In order to further our understanding of syngas combustion, a fundamental combustion study on syngas combustion at high pressure and lean condition was conducted through the collaboration with University of Southern California. A Methane program was also developed to rate engine performance for various compositions of syngas using empirical data obtained at CSU. While much work remains in terms of extending and integrating these developments into commercial products, it is evident that engine manufacturers on our own or through private consortium efforts could not have overcome the financial hurdles to drive these improvements into reciprocating engine and system capabilities, helping maintain the natural gas reciprocating engine power generation technology as a strong option for electric power markets, both in the United States and worldwide.

20 FOSSIL-FUELED POWER PLANTS↗

Effects of blending C3-C4 alcohols on motor gasoline properties and performance of spark ignition engines: A review

Supplementing petroleum fuels with sustainable and renewable alternatives is a good option for increasing the sustainability of transportation fuels. Alcohols are particularly attractive blendstocks for spark ignition engines, mainly due to their desirable fuel properties including high octane, evaporative cooling, and reduced sooting propensity. Although the use of SI engines is widespread around the world, predominately for light duty vehicles, concerns about CO2 emissions and other sustainability issues necessitate increased engine efficiencies, reduced tailpipe pollutants, and lower lifecycle carbon emissions. The intelligent blending of C2-C4 alcohols into motor gasoline is a viable method for achieving these goals. There are a multitude of ways to produce renewable alcohols such as through fermentation from first-generation feedstocks (sugar and corn) and second-generation feedstocks (lignocellulosic biomass), or by gasification and mixed alcohol fuel synthesis routes from lignocellulosic biomass. Currently ethanol is extensively used in motor gasoline fuels worldwide and although many have proposed the use of C3 and C4 alcohols in motor gasoline as an improvement over ethanol, the higher cost of production and lack of clear definition as to their benefit over ethanol when blended into motor gasoline have led to slow acceptance into the market. In this review, special emphasis is placed on the effects of blending C3 and C4 alcohols into motor gasoline in terms of physicochemical properties, volatility behavior, and engine performance when compared to ethanol blends. Furthermore, the impact of blending C3 and C4 alcohols with gasoline on emission (particulate matter, nitrogen oxides, carbon monoxide, hydrocarbons, and unregulated oxygenates) and combustion (volumetric efficiency, thermal efficiency, fuel consumption, and cold performance) characteristics is discussed. Although there are some disagreements in the literature over the effect of alcohols predominately around the type of SI engine, i.e., port fuel injected versus direct fuel injected and engine operating mode, generally it is stated that alcohols can potentially reduce soot, unburned hydrocarbons and CO emissions while increasing thermal efficiency when proper engine configuration/calibration is used. Lastly, research that must be conducted to find the optimum combination of alcohol blends and engine configurations is highlighted and discussed.

09 BIOMASS FUELS↗

Performance and emissions characteristics of bio-diesel (B100)-ignited methane and propane combustion in a four cylinder turbocharged compression ignition engine

Different combustion strategies and fuel sources are needed to deal with increasing fuel efficiency demands and emission restrictions. One possible strategy is dual fueling using readily available resources. Propane and natural gas are readily available with the current infrastructure and biodiesel is growing in popularity as a renewable fuel. This paper presents experimental results from dual fuel combustion of methane (as a surrogate for natural gas) and propane as primary fuels with biodiesel pilots in a 1.9 liter, turbocharged, 4 cylinder diesel engine at 1800 rev/min. Experiments were performed with different percentage energy substitutions (PES) of propane and methane and at different brake mean effective pressures (BMEP/bmep). Brake thermal efficiency (BTE) and emissions (NOx, HC, CO, CO2, O2 and smoke) were also measured. Maximum PES levels for B100-methane dual fuelling were limited to 70% at 2.5 bar bmep and 48% at 10 bar bmep, and corresponding values for B100-propane dual fuelling were 64% and 43%, respectively. Maximum PES was limited by misfire at 2.5 bar bmep and the onset of engine knock at 10 bar bmep. Dual fuel BTEs approached straight B100 values at 10 bar bmep while they were significantly lower than B100 values at 2.5 bar bmep. In general dual fuelling was beneficial in reducing NOx and smoke emissions by 33% and 50%, respectively from baseline B100 levels; however, both CO and THC emissions were significantly higher than baseline B100 levels at all PES and loads.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Evaluation of Propulsion Systems for Mach 2.4 and 3.2 High Speed Civil Transports

Advanced technology high speed civil transport (HSCT) engine cycles equipped with low emissions combustors and low noise exhaust nozzles were investigated. The objectives were as follows: (1) evaluate a range of cycle variables for engine types appropriate for Mach 2.4 and 3.2 HSCT; (2) select the most promising propulsion systems; and (3) identify and define the critical/key technology development and demonstration programs needed to be conducted prior to initiation of the product engine development and certification program. Two types of variable engines were studied: turbine bypass engines (TBE) and variable stream control engines (VSCE). This study identified payoffs in terms of aircraft gross weight, airline economics, stratospheric cruise emissions, and airport noise improvements. Comparison between the the TBE and VSCE showed the TBE to be clearly superior for Mach 2.4 and 3.2 cruise cruise operation. Critical technology areas were also identified which included the following: (1) Low emissions combustor; (2) Low noise exhaust system; (3) High temperature materials and coatings; (4) Advanced turbine cooling and aerodynamics; (5) Integrated propulsion system (inlet/engine/nozzle) and airframe controls; (6) Advanced fan/compressor aerodynamics; and (7) Magnetic bearings.

Turbine Bypass Engine (TBE)↗

2000 NASA Seal/Secondary Air System Workshop

The 2000 NASA Seal/Secondary Air System Workshop covered four main areas: (1) overviews of NASA-sponsored Ultra-Efficient Engine Technology (UEET) and Access to Space Programs, with emphasis on program goals and seal needs; (2) review of turbine engine seal issues from the perspective of end users such as United Airlines; (3) reviews of sealing concepts, test results, experimental facilities, and numerical predictions; and (4) reviews of material development programs relevant to advanced seals development. The NASA UEET overview illustrates for the reader the importance of advanced technologies, including seals, in meeting future engine system efficiency and emission goals. GE, Pratt & Whitney, and Honeywell presented advanced seal development work being performed within their organizations. The NASA-funded GE/Stein Seal team has successfully demonstrated a large (3-ft. diam) aspirating seal that can withstand all anticipated pressures, speeds, and rotor runouts anticipated for a GE90 L.P. turbine balance piston location. GE/Stein Seal are fabricating a full-scale seal to be tested in a GE-90 ground test engine in early 2002. Pratt & Whitney and Stein Seal are investigating carbon seals to accommodate large radial movements anticipated in future geared-fan gearbox locations. Honeywell presented a finger seal design being considered for a high-temperature static combustor location incorporating ceramic finger elements. Successful demonstration of the braided carbon rope thermal barriers to extreme temperatures (5500 F) for short durations provide a new form of very high temperature thermal barrier for future Shuttle solid rocket motor nozzle joints. The X-37, X-38, and future highly reusable launch vehicles pose challenging control surface seal demands that require new seal concepts made from emerging high temperature ceramics and other materials.

Steinetz, Bruce M.↗