Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Deposit”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

High-reliability passivation of hydrogen-terminated diamond surface by atomic layer deposition of Al{sub 2}O{sub 3}

Although the two-dimensional hole gas (2DHG) of a hydrogen-terminated diamond surface provides a unique p-type conducting layer for high-performance transistors, the conductivity is highly sensitive to its environment. Therefore, the surface must be passivated to preserve the 2DHG, especially at high temperature. We passivated the surface at high temperature (450 °C) without the loss of C-H surface bonds by atomic layer deposition (ALD) and investigated the thermal reliability of the Al{sub 2}O{sub 3} film. As a result, C-H bonds were preserved, and the hole accumulation effect appeared after the Al{sub 2}O{sub 3} deposition by ALD with H{sub 2}O as an oxidant. The sheet resistivity and hole density were almost constant between room temperature and 500 °C by the passivation with thick Al{sub 2}O{sub 3} film thicker than 38 nm deposited by ALD at 450 °C. After the annealing at 550 °C in air The sheet resistivity and hole density were preserved. These results indicate the possibility of high-temperature application of the C-H surface diamond device in air. In the case of lower deposition temperatures, the sheet resistivity increased after air annealing, suggesting an insufficient protection capability of these films. Given the result of sheet resistivity after annealing, the increase in the sheet resistivity of these samples was not greatly significant. However, bubble like patterns were observed in the Al{sub 2}O{sub 3} films formed from 200 to 400 °C by air annealing at 550 °C for 1 h. On the other hand, the patterns were no longer observed at 450 °C deposition. Thus, this 450 °C deposition is the sole solution to enabling power device application, which requires high reliability at high temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Selective deposition of a crystalline Si film by a chemical sputtering process in a high pressure hydrogen plasma

The selective deposition of Si films was demonstrated using a chemical sputtering process induced by a high pressure hydrogen plasma at 52.6 kPa (400 Torr). In this chemical sputtering process, the initial deposition rate (R{sub d}) is dependent upon the substrate type. At the initial stage of Si film formation, R{sub d} on glass substrates increased with elapsed time and reached to a constant value. In contrast, R{sub d} on Si substrates remained constant during the deposition. The selective deposition of Si films can be achieved by adjusting the substrate temperature (T{sub sub}) and hydrogen concentration (C{sub H2}) in the process atmosphere. For any given deposition time, it was found that an optimum C{sub H2} exists for a given T{sub sub} to realize the selective deposition of a Si film, and the optimum T{sub sub} value tends to increase with decreasing C{sub H2}. According to electron diffraction patterns obtained from the samples, the selectively prepared Si films showed epitaxial-like growth, although the Si films contained many defects. It was revealed by Raman scattering spectroscopy that some of the defects in the Si films were platelet defects induced by excess hydrogen incorporated during Si film formation. Raman spectrum also suggested that Si related radicals (SiH{sub 2}, SiH, Si) with high reactivity contribute to the Si film formation. Simple model was derived as the guideline for achieving the selective growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Finding evidence for density fluctuation effects on electron cyclotron heating deposition profiles on DIII-D

Theoretical work, computation, and results from TCV [J. Decker “Effect of density fluctuations on ECCD in ITER and TCV,” EPJ Web of Conf. 32, 01016 (2012)] suggest that density fluctuations in the edge region of a tokamak plasma can cause broadening of the ECH deposition profile. In this paper, a GUI tool is presented which is used for analysis of ECH deposition as a first step towards looking for this broadening, which could explain effects seen in previous DIII-D ECH transport studies [K.W. Gentle “Electron energy transport inferences from modulated electron cyclotron heating in DIII-D,” Phys. Plasmas 13, 012311 (2006)]. By applying an FFT to the T{sub e} measurements from the University of Texas’s 40-channel ECE Radiometer, and using a simplified thermal transport equation, the flux surface extent of ECH deposition is determined. The Fourier method analysis is compared with a Break-In-Slope (BIS) analysis and predictions from the ray-tracing code TORAY. Examination of multiple Fourier harmonics and BIS fitting methods allow an estimation of modulated transport coefficients and thereby the true ECH deposition profile. Correlations between edge fluctuations and ECH deposition in legacy data are also explored as a step towards establishing a link between fluctuations and deposition broadening in DIII-D.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Disilane as a growth rate catalyst of plasma deposited microcrystalline silicon thin films

The effect of small disilane addition on the gas phase properties of silane-hydrogen plasmas and the microcrystalline silicon thin films growth is presented. The investigation was conducted in the high pressure regime and for constant power dissipation in the discharge with the support of plasma diagnostics, thin film studies and calculations of discharge microscopic parameters and gas dissociation rates. The experimental data and the calculations show a strong effect of disilane on the electrical properties of the discharge in the pressure window from 2 to 3 Torr that is followed by significant raise of the electron number density and the drop of the sheaths electric field intensity. Deposition rate measurements show an important four to six times increase even for disilane mole fractions as low as 0.3 %. The deposition rate enhancement was followed by a drop of the material crystalline volume fraction but films with crystallinity above 40 % were deposited with different combinations of total gas pressure, disilane and silane molar ratios. The enhancement was partly explained by the increase of the electron impact dissociation rate of silane which rises by 40% even for 0.1% disilane mole fraction. The calculations of the gas usage, the dissociation and the deposition efficiencies show that the beneficial effect on the growth rate is not just the result of the increase of Si-containing molecules density but significant changes on the species participating to the deposition and the mechanism of the film growth are caused by the disilane addition. The enhanced participation of the highly sticking to the surface radical such as disilylene, which is the main product of disilane dissociation, was considered as the most probable reason for the significant raise of the deposition efficiency. The catalytic effect of such type of radical on the surface reactivity of species with lower sticking probability is further discussed, while it is also used to explain the restricted and sensitive process window where the disilane effect appears.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Vapor deposition rate modifies anisotropic glassy structure of an anthracene-based organic semiconductor

We control the anisotropic molecular packing of vapor-deposited glasses of ABH113, a deuterated anthracene derivative with promise for future organic light emitting diode materials, by changing the deposition rate and substrate temperature at which they are prepared. We find that at substrate temperatures from 0.65 T g to 0.92 T g , the deposition rate significantly modifies the orientational order in the vapor-deposited glasses as characterized by x-ray scattering and birefringence. Both measures of anisotropic order can be described by a single deposition rate–substrate temperature superposition (RTS). This supports the applicability of the surface equilibration mechanism and generalizes the RTS principle from previous model systems with liquid crystalline order to non-mesogenic organic semiconductors. We find that vapordeposited glasses of ABH113 have significantly enhanced density and thermal stability compared to their counterparts prepared by liquidcooling. For organic semiconductors, the results of this study provide an efficient guide for using the deposition rate to prepare stable glasses with controlled molecular packing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Particle deposition onto people in a transit venue

Following the release of an aerosolized biological agent in a transit venue, material deposited on waiting passengers and subsequently shed from their clothing may significantly magnify the scope and consequences of such an attack. Published estimates of the relevant particle deposition and resuspension parameters for complex, real-world environments such as a transit facility are non-existent. In this study, measurements of particle deposition velocity onto cotton fabric samples affixed to stationary and walking persons in a large multimodal transit facility were obtained for tracer particle releases carried out as part of a larger study of subway airflows and particulate transport. Deposition velocities onto cotton and wool were also obtained using a novel automated sampling mechanism deployed at locations in the transit facility and throughout the subway. The data revealed higher deposition velocities than have been previously reported for people exposed in test chambers or office environments. Furthermore, the relatively high rates of deposition onto people in a transit venue obtained in this study suggest it is possible that fomite transport by subway and commuter/regional rail passengers could present a significant mechanism for rapidly dispersing a biological agent throughout a metropolitan area and beyond.

59 BASIC BIOLOGICAL SCIENCES↗

Atomic layer deposition-based functionalization of materials for medical and environmental health applications

Nanoporous alumina membranes exhibit high pore densities, well-controlled and uniform pore sizes, as well as straight pores. Owing to these unusual properties, nanoporous alumina membranes are currently being considered for use in implantable sensor membranes and water purification membranes. Atomic layer deposition is a thin-film growth process that may be used to modify the pore size in a nanoporous alumina membrane while retaining a narrow pore distribution. In addition, films deposited by means of atomic layer deposition may impart improved biological functionality to nanoporous alumina membranes. In this study, zinc oxide coatings and platinum coatings were deposited on nanoporous alumina membranes by means of atomic layer deposition. PEGylated nanoporous alumina membranes were prepared by self-assembly of 1-mercaptoundec-11-yl hexa(ethylene glycol) on platinum-coated nanoporous alumina membranes. The pores of the PEGylated nanoporous alumina membranes remained free of fouling after exposure to human platelet-rich plasma; protein adsorption, fibrin networks and platelet aggregation were not observed on the coated membrane surface. Zinc oxide-coated nanoporous alumina membranes demonstrated activity against two waterborne pathogens, Escherichia coli and Staphylococcus aureus. The results of this work indicate that nanoporous alumina membranes may be modified using atomic layer deposition for use in a variety of medical and environmental health applications.

antimicrobial↗

Effects of temperature and particle size on deposition in land based turbines - article no. 051503

Four series of tests were performed in an accelerated deposition test facility to study the independent effects of particle size, gas temperature, and metal temperature on ash deposits from two candidate power turbine synfuels (coal and petcoke). The facility matches the gas temperature and velocity of modern first stage high pressure turbine vanes while accelerating the deposition process. Particle size was found to have a significant effect on capture efficiency with larger particles causing significant thermal barrier coating (TBC) spallation during a 4 h accelerated test. In the second series of tests, particle deposition rate was found to decrease with decreasing gas temperature. The threshold gas temperature for deposition was approximately 960{sup o}C. In the third and fourth test series, impingement cooling was applied to the back side of the target coupon to simulate internal vane cooling. Capture efficiency was reduced with increasing mass flow of coolant air; however, at low levels of cooling, the deposits attached more tenaciously to the TBC layer. Postexposure analyses of the third test series (scanning electron microscopy and X-ray spectroscopy) show decreasing TBC damage with increased cooling levels.

20 FOSSIL-FUELED POWER PLANTS↗

Mechanical properties of amorphous hydrogenated carbon films fabricated on polyethylene terephthalate foils by plasma immersion ion implantation and deposition

Amorphous hydrogenated carbon (a-C:H) films have been deposited on polyethylene terephthalate by plasma immersion ion implantation and deposition. The influence of deposition parameters such as gas pressure, bias voltage, and nitrogen incorporation on the mechanical properties of the a-C:H films are investigated. X-ray photoelectron spectroscopy reveals that the ratio of sp{sup 3} to sp{sup 2} is 0.24 indicating that the film is mainly composed of graphitelike carbon. Nanoindentation tests disclose enhanced surface hardness of {approx}6 GPa. The friction coefficient of the film deposited at higher gas pressure, for instance, 2.0 Pa, is lower than that of the film deposited at a lower pressure such as 0.5 Pa. The films deposited using a low bias voltage tend to fail easily in the friction tests and nitrogen incorporation into the a-C:H films decreases the friction coefficient. Mechanical folding tests show that deformation failure is worse on a thinner a-C:H film.

36 MATERIALS SCIENCE↗

Compositional analysis of lead telluride films deposited via pulsed electron-beam ablation

Pulsed electron deposition (PED) is a novel thin film growth technique with unique advantages for industrial-scale manufacturing. Previously, no investigations into local deviations in stoichiometry have been carried out. The authors report the first analysis of large-scale compositional variations in thin films deposited via PED. Ablated lead telluride (PbTe) was deposited at various target-substrate distances on 5 cm{sup 2} substrates. Rutherford backscattering was employed to systematically analyze compositional variation at different positions within the deposition. Stoichiometry is reported as a function of both distance and angular displacement. Deposition rates for the center of the ablated plume are reported. The authors show PED to be capable of uniform deposition over areas of moderate (0.5-1 cm{sup 2}) size, with an enrichment of heavier elements in the center of the film. The results are explained within the context of expanding plasma behavior.

36 MATERIALS SCIENCE↗

Growth and interface of HfO{sub 2} films on H-terminated Si from a TDMAH and H{sub 2}O atomic layer deposition process

HfO{sub 2} thin films have been deposited by an atomic layer deposition (ALD) process using alternating pulses of tetrakis(dimethyl)amino hafnium and H{sub 2}O precursors at a substrate temperature of 200-325 deg. C. The initial stage of film growth on OH- and H-terminated Si(100) surfaces is investigated using Rutherford backscattering spectrometry (RBS), x-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). The authors observe an initial growth barrier on the Si-H surface for the first approximately four process cycles, where film growth is more efficient on the OH-terminated surface. Both starting surfaces require about 15 cycles to reach a steady growth rate per cycle, with the OH-terminated surface displaying a slightly higher growth rate of 2.7x10{sup 14} Hf/cm{sup 2} compared to 2.4x10{sup 14} Hf/cm{sup 2} for Si-H. Combining the RBS and SE data we conclude that the films deposited on the OH-terminated surface are denser than those deposited on the Si-H surface. Angle-resolved XPS measurements reveal the formation of an {approx}8 A interfacial layer after four ALD cycles on the H-terminated surface for a deposition temperature of 250 deg. C, and transmission electron microscopy verifies that the thickness of the interfacial layer does not change substantially between the 4th and the 25th process cycles. The interfacial layer appears to depend weakly on the deposition temperature from 200 to 325 deg. C, ranging from 6.9 to 8.4 A.

36 MATERIALS SCIENCE↗

Microstructure and chemical wet etching characteristics of AlN films deposited by ac reactive magnetron sputtering

The influence of the surface morphology of a molybdenum underlayer on the crystallinity and etchability of reactively sputtered c-axis oriented aluminum nitride thin films was investigated. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, high resolution x-ray diffraction, and defect selective chemical etching were used to characterize the microstructure of the Mo and AlN films. 1000 nm thick films of AlN with a full width at half maximum (FWHM) of the x-ray rocking curve ranging from 1.1 deg. to 1.9 deg. were deposited on 300 nm thick Mo underlayers with a FWHM of around 1.5 deg. The Ar pressure during the Mo deposition had a critical effect on the Mo film surface morphology, affecting the structure of the subsequently deposited AlN films and, hence, their wet etching characteristics. AlN films deposited on Mo sputtered at a relatively high pressure could not be etched completely, while AlN films deposited on low pressure Mo etched more easily. Postdeposition etching of the Mo surface in Ar rf discharge prior to deposition of the AlN film was found to influence the formation of AlN residuals that were difficult to etch. Optimal rf plasma etching conditions were found, which minimized the formation of these residuals.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electrical resistivity change in Al:ZnO thin films dynamically deposited by bipolar pulsed direct-current sputtering and a remote plasma source

The Al-doped ZnO (AZO) thin films for a transparent conducting oxide in solar cell devices were deposited by bipolar pulsed dc magnetron sputtering. This work was performed in an in-line type system and investigated AZO films in a static deposition mode and dynamic one, which is more important in the practical fields. Because of this dynamic deposition process, the zigzagged columnar structure was observed. This resulted in the decreasing electrical property, optical properties, and surface roughness. As a deposition in the dynamic mode, the resistivity increased from 1.64x10{sup -3} to 2.50x10{sup -3} {Omega} cm, as compared to that in the static mode, and the transmittance also decreased from 83.9% to 78.3%. To recover the disadvantage, a remote plasma source (RPS) was supported between the substrate and target for reducing zigzagged formation during the deposition. The deposition rate decreased by using RPS, but the electrical and optical properties of films got better than only dynamic mode. The resistivity and transmittance in the dynamic mode using RPS were 2.1x10{sup -3} {Omega} cm and 85.5%, respectively. In this study, the authors found the possibility to advance the electrical and optical properties of AZO thin films in the industry mode.

36 MATERIALS SCIENCE↗

Influence of temperature on the hydrogenated amorphous carbon films prepared by plasma-enhanced chemical vapor deposition

Hydrogenated amorphous carbon (a-C:H) films were deposited in a plasma-enhanced chemical vapor deposition (PECVD) system. The substrate temperature at deposition was found to have significant effects on the film stoichiometry, sp{sup 2} phase, and optical properties. Raman spectroscopy reveals an increase in sp{sup 2}-bonded carbon and a continual structure ordering of the sp{sup 2} phase with increasing substrate temperature at deposition. Thermal desorption spectroscopy analysis revealed that the onset temperature of CH{sub 4} effusion of PECVD a-C:H films increase with increasing substrate temperatures, implicating enhanced structural stability via elevating the substrate temperature at deposition. The extinction coefficient k measured from spectroscopic ellipsometry gradually increases with increasing substrate temperature at deposition, due possibly to the graphitization effect which decreases the optical gap resulting in higher k.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scalability of plasma enhanced atomic layer deposited ruthenium films for interconnect applications

Ru thin films were deposited by plasma enhanced atomic layer deposition using MethylCyclopentadienylPyrrolylRuthenium (MeCpPy)Ru and N{sub 2}/NH{sub 3} plasma. The growth characteristics have been studied on titanium nitride or tantalum nitride substrates of various thicknesses. On SiO{sub 2}, a large incubation period has been observed, which can be resolved by the use of a metal nitride layer of {approx} 0.8 nm. The growth characteristics of Ru layers deposited on ultra-thin metal nitride layers are similar to those on thick metal nitride substrates despite the fact that the metal nitride layers are not fully closed. Scaled Ru/metal nitride stacks were deposited in narrow lines down to 25 nm width. Thinning of the metal nitride does not impact the conformality of the Ru layer in the narrow lines. For the thinnest lines the Ru deposited on the side wall showed a more granular structure when compared to the bottom of the trench, which is attributed to the plasma directionality during the deposition process.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diffusion and interface evolution during the atomic layer deposition of TiO{sub 2} on GaAs(100) and InAs(100) surfaces

Atomic layer deposition is used to form TiO{sub 2} films from tetrakis dimethyl amino titanium and H{sub 2}O on native oxide GaAs(100) and InAs(100) surfaces. The evolution of the film/substrate interface is examined as a function of the deposition temperature (100–325 °C) using ex situ x-ray photoelectron spectroscopy. An increase in the deposition temperature up to 250 °C leads to enhancement of the native oxide removal. For depositions at 300 °C and above, interface reoxidation is observed during the initial deposition cycles but when the films are thicker than 3 nm, the surface oxides are removed steadily. Based on these observations, two distinct film growth regimes are identified; up to 250 °C, layer-by-layer dominates while at higher temperatures island growth takes over. Angle resolved x-ray photoelectron spectroscopy measurements performed on 3 nm TiO{sub 2} film deposited at 325 °C on both surfaces demonstrates a very important difference between the two substrates: for GaAs the native oxides remaining in the stack are localized at the interface, while for InAs(100), the indium oxides are mixed in the TiO{sub 2} film.

36 MATERIALS SCIENCE↗

Native oxide transport and removal during the atomic layer deposition of Ta{sub 2}O{sub 5} on InAs(100) surfaces

Atomic layer deposition (ALD) was used to deposit Ta{sub 2}O{sub 5} on etched and native oxide-covered InAs(100) using pentakis dimethyl amino tantalum and H{sub 2}O at 200–300 °C. The transport and removal of the native oxides during the ALD process was investigated using x-ray photoelectron spectroscopy (XPS). Depositions above 200 °C on etched surfaces protected the interface from reoxidation. On native oxide-covered surfaces, depositions resulted in enhanced native oxide removal at higher temperatures. The arsenic oxides were completely removed above 250 °C after 3 nm of film growth, but some of the As{sub 2}O{sub 3} remained in the film at lower temperatures. Angle-resolved and sputter depth profiling XPS confirmed indium and arsenic oxide migration into the Ta{sub 2}O{sub 5} film at deposition temperatures as low as 200 °C. Continuous removal of both arsenic and indium oxides was confirmed even after the deposition of several monolayers of a coalesced Ta{sub 2}O{sub 5} film, and it was demonstrated that native oxide transport is a prevalent component of the interface “clean-up” mechanism.

36 MATERIALS SCIENCE↗

Magnetized, radiofrequency-driven hollow cathode chemical-vapor deposition of ultrathick hydrogenated amorphous carbon

Amorphous carbon is an attractive material for next-generation inertial confinement fusion (ICF) ablators due to its amorphous structure, tunable density, compatibility with dopants, chemical inertness, and mechanical robustness. Ablators are typically deposited as ultrathick (10–200 μm) coatings on removable spherical templates. The deposition of such thick amorphous carbon films is challenging due to high intrinsic compressive stress, which causes film buckling and delamination. Here, we study the deposition of amorphous carbon films by magnetized, radiofrequency-driven hollow cathode chemical vapor deposition with a custom-designed source in Ne plasmas. Emphasis is on the hollow-cathode source design and effects of the plasma discharge power and the precursor flow rate on film properties. We demonstrate deposition rates of >1 μm/h for films with hydrogen content of ∼40 at. %, densities of 1.1–1.7 g/cm 3 , and trace quantities of oxygen impurities. In conclusion, we also demonstrate the feasibility of depositing thick hydrogenated amorphous carbon films (∼30 μm) for ICF applications.

Carbon based materials↗