Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cleaned”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Extraction of a Clean Charge-Density-Wave Gap for 2H-Na(X)TaS(2)

We develop a novel decomposition method to extract a clean charge-density-wave (CDW) gap of sodium doped 2H-TaS{sub 2} from its partially suppressed photoemission spectra in the CDW state. We find that about 1/3 of the spectrum is fully gapped, while the other 2/3 is ungapped. Our results are contrary to a recent theoretical proposal based on the band picture that divides the system into three decoupled sublattices, with two being distorted due to the CDW formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solvent cleaning system and method for removing contaminants from solvent used in resin recycling

A two step solvent and carbon dioxide based system that produces essentially contaminant-free synthetic resin material and which further includes a solvent cleaning system for periodically removing the contaminants from the solvent so that the solvent can be reused and the contaminants can be collected and safely discarded in an environmentally safe manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Implications of Low Particulate Matter Emissions on System Fuel Efficiency for High Efficiency Clean Combustion

Advanced diesel combustion regimes such as High Efficiency Clean Combustion (HECC) offer the benefits of reduced engine out NOX and particulate matter (PM) emissions. Lower PM emissions during advanced combustion reduce the demand on diesel particulate filters (DPFs) and can, thereby, reduce the fuel penalty associated with DPF regeneration. In this study, a SiC DPF was loaded and regenerated on a 1.7-liter 4-cylinder diesel engine operated in conventional and advanced combustion modes at different speed and load conditions. A diesel oxidation catalyst (DOC) and a lean NOX trap (LNT) were also installed in the exhaust stream. Five steady-state speed and load conditions were weighted to estimate Federal Test Procedure (FTP) fuel efficiency. The DPF was loaded using lean-rich cycling with frequencies that resulted in similar levels of NOX emissions downstream of the LNT. The pressure drop across the DPF was measured at a standard point (1500 rpm, 5.0 bar) before and after loading, and a P rise rate was determined for comparison between conventional and advanced combustion modes. Higher PM emissions in conventional combustion resulted in a higher rate of backpressure rise across the DPF at all of the load points leading to more frequent DPF regenerations and higher fuel penalty. The fuel penalty during conventional combustion was 4.2% compared with 3.1% for a mixture of conventional and advanced modes.

33 ADVANCED PROPULSION SYSTEMS↗

Carbon Smackdown: Visualizing Clean Energy (LBNL Summer Lecture Series)

The final Carbon Smackdown match took place Aug. 9, 2010. Juan Meza of the Computational Research Division revealed how scientists use computer visualizations to accelerate climate research and discuss the development of next-generation clean energy technologies such as wind turbines and solar cells.

54 ENVIRONMENTAL SCIENCES↗

Investing in Clean, Safe Nuclear Energy

President Obama announces more than $8 billion in loan guarantees for two new nuclear reactors as part of the Administration's commitment to providing clean energy and creating new jobs.

Nuclear Energy, DOE, Steven Chu, Obama Administrat↗

Manufacturing in the Clean Energy Race

There is an energy and manufacturing revolution in the world today. Here is what the United States Department of Energy has done through collaborations in pursuit of American prosperity in the energy and manufacturing industry of tomorrow.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Cleaning of Wastewater from Total Coliform Using Chitosan–Grafted–Poly(2-methylaniline)

The preparation and characterization of a low-cost solid materials chitosan–graft–poly(2-methylaniline) as anti-coliform present in wastewater are confirmed by FTIR, TGA, XRD and SEM. The preparation is performed using ammonium persulphate as an oxidant. The data reveals that the grafting process enhances the efficiency of both chitosan and homo-poly(2-methylaniline) to remove coliform present in wastewater. The used wastewater contains 1600 colonies on testing total coliform using classical membrane filter techniques. The total coliform present in wastewater becomes zero by using 50 ppm of the graft, 100 ppm of chitosan and 1000 ppm of poly(2-methylaniline).

36 MATERIALS SCIENCE↗

Olivine, dolomite and ceramic filters in one vessel to produce clean gas from biomass

Highlights: • Syngas free of particles and with very low amount of tar is produced from biomass gasification. • Combination is tested of primary catalyst in the gasifier fluidized bed with catalytic ceramic candles in its freeboard. • Remarkable process intensification and thermal integration is obtained. • The adoption of catalytic filter candles doesn’t increase the required standard filtration surface in practical applications. - Abstract: Heavy organic compounds produced during almond shells gasification in a steam and/or air atmosphere, usually called tar, are drastically reduced in the product gas by using simultaneously in one vessel a ceramic filter placed in the freeboard and a mixture of olivine and dolomite particles in the fluidized bed of the gasifier. The content of tar in the product gas during a reference gasification test with air, in presence of fresh olivine particles only, was 8600 mg/Nm{sup 3} of dry gas. By gasifying biomass with steam at the same temperature level of 820 °C in a bed of olivine and dolomite (20% by weight), and in the presence of a catalytic ceramic filter inserted in the freeboard of the fluidized bed gasifier, the level of tar was brought down to 57 mg/Nm{sup 3} of dry producct gas, with a decrease of more than two orders of magnitude.

09 BIOMASS FUELS↗

Regeneration of Sulfur Deactivated Ni-based Biomass Syngas Cleaning Catalysts

Nickel-based catalysts have been widely tested in decomposing tar and methane in hot biomass syngas cleanup researches. However these catalysts can be easily deactivated by the sulfur compounds in syngas due to the strong sulfur adsorption effect on the Ni surface. Here we report on a new regeneration process, which can effectively and efficiently regenerate the sulfur-poisoned Ni reforming catalysts. This process consists of four sequential treatments: 1) controlled oxidation at 750oC in 1% O2, 2) decomposition at 900oC in Ar, 3) reduction at 900oC in 2% H2, and 4) reaction at 900oC under reforming condition. The duration of this 4-step regeneration process is only about 8 hours, which is shorter than that of the conventional steaming regeneration treatment.

03 NATURAL GAS↗

Depth-dependent magnetism in epitaxial MnSb thin films: effects of surface passivation and cleaning

Depth-dependent magnetism in MnSb(0001) epitaxial films has been studied by combining experimental methods with different surface specificities: polarized neutron reflectivity, x-ray magnetic circular dichroism (XMCD), x-ray resonant magnetic scattering and spin-polarized low energy electron microscopy (SPLEEM). A native oxide {approx}4.5 nm thick covers air-exposed samples which increases the film's coercivity. HCl etching efficiently removes this oxide and in situ surface treatment of etched samples enables surface magnetic contrast to be observed in SPLEEM. A thin Sb capping layer prevents oxidation and preserves ferromagnetism throughout the MnSb film. The interpretation of Mn L{sub 3,2} edge XMCD data is discussed.

36 MATERIALS SCIENCE↗

JET EROSION OF PARTICLE BEDS: PROJECTING CRITICAL SUSPENSION VELOCITIES FROM EFFECTIVE CLEARING / CLEANING RADII

Here we explore the relationship between effective cleaning/clearing radii, ECR, and critical suspension velocities, Ucs. Although one set of physics controls both the radial extent of erosion (i.e., the ECR) and the velocity needed to erode from the center of jet impingement to any given location (i.e., Ucs, typically defined from nozzle center to the vessel center), the relationship between these two remains unexplored quantitatively. Here we advance the model of Kuhn, et al., (PNNL-22816, 2013) as described by Pease, et al. (FEDSM2017-69444, 2017) to evaluate the relationship between the effective clearing/cleaning radius and the nozzle velocity on flat surfaces including flat bottomed vessels. Two governing dimensionless groups are identified. We present both a closed form analytical but transcendental solution and a non-iterative approximation modeled after the Serghides approximation of Colebrook’s nonlinear equation for both ECR versus nozzle velocity and Ucs. Comparison of the model to data from flume testing on a flat surface finds reasonable agreement.

jet, erosion, critical suspension velocity, effect↗

Surface cleaning for enhanced adhesion to packaging surfaces: Effect of oxygen and ammonia plasma

The effects of direct plasma chemistries on carbon removal from silicon nitride (SiN{sub x}) and oxynitride (SiO{sub x}N{sub y}) surfaces have been studied by in-situ x-ray photoelectron spectroscopy (XPS) and ex-situ contact angle measurements. The data indicate that O{sub 2} and NH{sub 3} capacitively coupled plasmas are effective at removing adventitious carbon from silicon nitride (SiN{sub x}) and Si oxynitride (SiO{sub x}N{sub y}) surfaces. O{sub 2} plasma treatment results in the formation of a silica overlayer. In contrast, the exposure to NH{sub 3} plasma results in negligible additional oxidation of the SiN{sub x} or SiO{sub x}N{sub y} surface. Ex-situ contact angle measurements show that SiN{sub x} and SiO{sub x}N{sub y} surfaces exposed to oxygen plasma are initially more hydrophilic than surfaces exposed to NH{sub 3} plasma, indicating that the O{sub 2} plasma-induced SiO{sub 2} overlayer is highly reactive toward ambient. At longer ambient exposures (≳10 h), however, surfaces treated by either O{sub 2} or NH{sub 3} plasma exhibit similar steady state contact angles, correlated with rapid uptake of adventitious carbon, as determined by XPS. Surface passivation by exposure to molecular hydrogen prior to ambient exposure significantly retards the increase in contact angle upon exposure to ambient. The results suggest a practical route to enhancing the time available for effective bonding to surfaces in microelectronics packaging applications.

36 MATERIALS SCIENCE↗

EDIN-USVI Clean Energy Quarterly: Volume 1, Issue 2, March 2011, Energy Development in Island Nations, U.S. Virgin Islands (Newsletter)

This quarterly newsletter provides timely news and information about the plans and progress of the Energy Development in Island Nations U.S. Virgin Islands pilot project, including significant events and milestones, work undertaken by each of the five working groups, and project-related renewable energy and energy efficiency projects.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗