Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Casting Designs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗

Preliminary design study of solar probe heat shields

The requirements, constraints, design guidelines, and expected performances of heat-shield systems for a solar probe are analyzed. A multiple-stage, asymmetric, right-angle radiation cascade configuration is used as the basis for comparison. Output-to-input radiative flux ratios are first calculated for a system employing gray surfaces. Assuming that the temperature of the inner surface of the payload bus is allowed to reach 400 K, it is shown that four- and five-stage cascade systems employing graphite can approach, respectively, to within about 5.5 and 4 solar radii of the sun. The systems using slip-cast silica and tungsten are then analyzed accounting for the degradation of surface-optical performance caused by the solar wind. It is shown that two- and three-stage silica-tungsten systems can approach, respectively, to within 4 and 3 solar radii of the sun.

Park, C.↗

Methodology for sensitivity analysis, approximate analysis, and design optimization in CFD for multidisciplinary applications

In this study involving advanced fluid flow codes, an incremental iterative formulation (also known as the delta or correction form) together with the well-known spatially-split approximate factorization algorithm, is presented for solving the very large sparse systems of linear equations which are associated with aerodynamic sensitivity analysis. For smaller 2D problems, a direct method can be applied to solve these linear equations in either the standard or the incremental form, in which case the two are equivalent. Iterative methods are needed for larger 2D and future 3D applications, however, because direct methods require much more computer memory than is currently available. Iterative methods for solving these equations in the standard form are generally unsatisfactory due to an ill-conditioning of the coefficient matrix; this problem can be overcome when these equations are cast in the incremental form. These and other benefits are discussed. The methodology is successfully implemented and tested in 2D using an upwind, cell-centered, finite volume formulation applied to the thin-layer Navier-Stokes equations. Results are presented for two sample airfoil problems: (1) subsonic low Reynolds number laminar flow; and (2) transonic high Reynolds number turbulent flow.

Taylor, Arthur C., III↗

Monolayer Plasmonic Nanoframes as Large‐Area, Broadband Metasurface Absorbers

Abstract Broadband absorbers are useful ultraviolet protection, energy harvesting, sensing, and thermal imaging. The thinner these structures are, the more device‐relevant they become. However, it is difficult to synthesize ultrathin absorbers in a scalable and straightforward manner. A general and straightforward synthetic strategy for preparing ultrathin, broadband metasurface absorbers that do not rely on cumbersome lithographic steps is reported. These materials are prepared through the surface‐assembly of plasmonic octahedral nanoframes (NFs) into large‐area ordered monolayers via drop‐casting with subsequent air‐drying at room temperature. This strategy is used to produce three types of ultrathin broadband absorbers with thicknesses of ≈200 nm and different lattice symmetries (loose hexagonal, twisted hexagonal, dense hexagonal), all of which exhibit efficient light absorption (≈90%) across wavelengths ranging from 400–800 nm. Their broadband absorption is attributed to the hollow morphologies of the NFs, the incorporation of a high‐loss material (i.e., Pt), and the strong field enhancement resulting from surface assembly. The broadband absorption is found to be polarization‐independent and maintained for a wide range of incidence angles (±45°). The ability to design and fabricate broadband metasurface absorbers using this high‐throughput surface‐based assembly strategy is a significant step toward the large‐scale, rapid manufacturing of nanophotonic structures and devices.

36 MATERIALS SCIENCE↗

An AC modulated near infrared gain calibration system for a “Violin-Mode” transimpedance amplifier, intended for advanced LIGO suspensions

The background to this work was a prototype shadow sensor, which was designed for retro-fitting to an advanced LIGO (Laser Interferometer Gravitational wave Observatory) test-mass/mirror suspension, in which a 40 kg test-mass/mirror is suspended by four approximately 600 mm long by 0.4 mm diameter fused-silica suspension fibres. The shadow sensor comprised a LED source of Near InfraRed (NIR) radiation, and a “tall-thin” rectangular silicon photodiode detector, which together were to bracket the fibre under test. The photodiode was positioned so as to be sensitive (primarily) to transverse “Violin-Mode” vibrations of such a fibre, via the oscillatory movement of the shadow cast by the fibre, as this moved across the face of the detector. In this prototype shadow sensing system the photodiode was interfaced to a purpose-built transimpedance amplifier, this having both AC and DC outputs. A quasi-static calibration was made of the sensor’s DC responsivity, i.e., incremental rate of change of output voltage versus fibre position, by slowly scanning a fused-silica fibre sample transversely through the illuminating beam. The work reported here concerns the determination of the sensor’s more important AC (Violin-Mode) responsivity. Recognition of the correspondence between direct AC modulation of the source, and actual Violin-Mode signals, and of the transformative role of the AC/DC gain ratio for the amplifier, at any modulation frequency, f, resulted in the construction of the AC/DC calibration source described here. A method for determining in practice the transimpedance AC/DC gain ratio of the photodiode and amplifier, using this source, is illustrated by a specific numerical example, and the gain ratio for the prototype sensing system is reported over the frequency range 1 Hz–300 kHz. In fact, a maximum DC responsivity of 1.26 kV.m{sup −1} was measured using the prototype photodiode sensor and amplifier discussed here. Therefore, the measured AC/DC transimpedance gain ratio of 922.5 for this sensor, at 500 Hz, translated into a maximum Violin-Mode (AC) responsivity of (1.16 ± 0.05) MV m{sup −1}, at that frequency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cosmology with liquid mirror telescopes

Liquid mirrors provide an exciting means to obtain large optical telescopes for substantially lower costs than conventional technologies. The liquid mirror concept has been demonstrated in the lab with the construction of a diffraction limited 1.5 m mirror. The mirror surface, using liquid mercury, forms a perfect parabolic shape when the mirror cell is rotated at a uniform velocity. A liquid mirror must be able to support a heavy mercury load with minimal flexure and have a fundamental resonant frequency that is as high as possible, to suppress the amplitude of surface waves caused by small vibrations transmitted to the mirror. To minimize the transmission of vibrations to the liquid surface, the entire mirror rests on an air bearing. This necessitates the mirror cell being lightweight, due to the limited load capabilities of the air bearing. The mirror components must also have physical characteristics which minimize the effects of thermal expansion with ambient temperature fluctuations in the observatory. In addition, the 2.7 m mirror construction is designed so that the techniques used may be readily extended to the construction of large mirrors. To attain the goals of a lightweight, rigid mirror, a composite laminant construction was used. The mirror consists of a foam core cut to the desired parabolic shape, with an accuracy of a few mm. An aluminum hub serves as an anchor for the foam and skin, and allows precise centering of the mirror on the air bearing and drive system. Several plys of Kevlar, covered in an epoxy matrix, are then applied to the foam. A final layer of pure epoxy is formed by spin casting. This final layer is parabolic to within a fraction of a mm. An aluminum ring bonded to the circumference of the mirror retains the mercury, and incorporates stainless-steel hard-points for the attachment of balance weights.

Hogg, David W.↗

Atmospheric chemistry of the reaction ClO + O2 reversible reaction ClO (center dot) O2: Where it stands, what needs to be done, and why?

Possible existence and chemistry of ClO (center dot) O2 was originally proposed to explain the Norrish-Neville effect that O2 suppresses chlorine photosensitized loss of ozone. It was also thought that ClO (center dot) O2 might have some atmospheric chemistry significance. Recently, doubts have been cast on this proposal, because certain laboratory data seem to imply that the equilibrium constant of the title reaction is so small that ClO (center dot) O2 may be too unstable to matter. However, those data create only a superficial illusion to that effect, because on a closer analysis they do not disprove a moderately stable and chemically significant ClO (center dot) O2. Furthermore, our state-of-the-science accurate computational chemistry calculations also suggest that ClO (center dot) O2 may be a weakly bound ClOOO radical with a reactive (2)A ground electronic state. There is therefore a need to design and perform definitive experimental tests of the existence and chemistry of the ClO (center dot) O2 species, which we discuss and which have the potential to mediate the chlorine-catalyzed stratospheric ozone depletion.

Prasad, Sheo S.↗

Microstructure and Mechanical Properties of Low-Activation Fe-Cr-V Multicomponent Single-Phase Alloys

A ternary equiatomic and nearly equiatomic alloy composed of the low-activation elements Fe, Cr, and V was designed for potential application as low-activation structural materials for the first wall of fusion reactors. The optimal composition of the multicomponent alloy was determined by minimizing the Gibbs free energy for solid-solution formation. The microstructure, phase stability, and mechanical properties of the equiatomic and optimized Fe-Cr-V alloys were studied. The equiatomic alloy consisted of a body-centered-cubic (BCC) solid-solution phase with a small amount of a face-centered-cubic (FCC) solid-solution phase, whereas the optimized alloy consisted of a single BCC solid-solution phase in the as-cast state. The crystal grains of both alloys were equiaxial. No phase transition was observed in the optimized alloy after homogenization; however, for the equiatomic alloy, the FCC solid-solution phase disappeared and surface relief was observed. The Vickers microhardness and yield strength of the Fe-Cr-V alloys increased after homogenization compared with those of the as-cast alloys.

36 MATERIALS SCIENCE↗

Fracture Analysis of Particulate Reinforced Metal Matrix Composites

A fracture analysis of highly loaded particulate reinforced composites was performed using laser moire interferometry to measure the displacements within the plastic zone at the tip of an advancing crack. Ten castings were made of five different particulate reinforcement-aluminum alloy combinations. Each casting included net-shape specimens which were used for the evaluation of fracture toughness, tensile properties, and flexure properties resulting in an extensive materials properties data. Measured fracture toughness range from 14.1 MPa for an alumina reinforced 356 aluminum alloy to 23.9 MPa for a silicon carbide reinforced 2214 aluminum alloy. For the combination of these K(sub Ic) values and the measured tensile strengths, the compact tension specimens were too thin to yield true plane strain K(sub Ic) values. All materials exhibited brittle behavior characterized by very small tensile ductility suggesting that successful application of these materials requires that the design stresses be below the elastic limit. Probabilistic design principles similar to those used with ceramics are recommended when using these materials. Such principles would include the use of experimentally determined design allowables. In the absence of thorough testing, a design allowable stress of 60 percent of the measured ultimate tensile stress is recommended.

Min, James B.↗

Evolution of the role of molybdenum in duplex stainless steels during thermal aging: From enhancing spinodal decomposition to forming heterogeneous precipitates

Thermal aging of ferrite in duplex stainless steels leads to a complex microstructural evolution that can give way to large deleterious changes in mechanical properties. The microstructural evolution mechanisms that happen concurrently are strongly linked to minor changes in composition. By characterizing duplex stainless steels with various compositions over a range of aging conditions, it was revealed that adding a modest amount of Mo to cast austenitic stainless steel (such as changing from grade CF3 to grade CF3M) not only increases the kinetics of spinodal decomposition and Ni-Si-Mn-rich G-phase precipitation, but it also forms a separate Mo-rich phase. At shorter equivalent aging times, Mo segregates from Fe and towards Cr accelerating spinodal decomposition. At longer aging times, Mo enriches in the Ni-Si-Mn clusters before phase separating into an adjoined Mo-rich cluster. We found that these phase changes and precipitation events result in a rather steep drop in fracture and impact toughness. These results will inform the design of similar alloys for use at high temperatures.

36 MATERIALS SCIENCE↗

Final Report on Developing Microstructure-Property Correlation in Reactor Materials using in situ High-Energy X-rays

This report provides a summary of research activities on understanding microstructure – property correlation in reactor materials using in situ high-energy X-rays. The report is a Level 2 deliverable in FY16 (M2CA-13-IL-AN_-0403-0111), under the Work Package CA-13-IL-AN_- 0403-01, “Microstructure-Property Correlation in Reactor Materials using in situ High Energy Xrays”, as part of the DOE-NE NEET Program. The objective of this project is to demonstrate the application of in situ high energy X-ray measurements of nuclear reactor materials under thermal-mechanical loading, to understand their microstructure-property relationships. The gained knowledge is expected to enable accurate predictions of mechanical performance of these materials subjected to extreme environments, and to further facilitate development of advanced reactor materials. The report provides detailed description of the in situ X-ray Radiated Materials (iRadMat) apparatus designed to interface with a servo-hydraulic load frame at beamline 1-ID at the Advanced Photon Source. This new capability allows in situ studies of radioactive specimens subject to thermal-mechanical loading using a suite of high-energy X-ray scattering and imaging techniques. We conducted several case studies using the iRadMat to obtain a better understanding of deformation and fracture mechanisms of irradiated materials. In situ X-ray measurements on neutron-irradiated pure metal and model alloy and several representative reactor materials, e.g. pure Fe, Fe-9Cr model alloy, 316 SS, HT-UPS, and duplex cast austenitic stainless steels (CASS) CF-8 were performed under tensile loading at temperatures of 20-400°C in vacuum. A combination of wide-angle X-ray scattering (WAXS), small-angle X-ray scattering (SAXS), and imaging techniques were utilized to interrogate microstructure at different length scales in real time while the specimen was subject to thermal-mechanical loading. In addition, in situ X-ray studies were complemented and benchmarked by ex situ characterization using advanced electron microscopy, atom probe tomography (APT) and micro/nano-indentation. The report presented in situ tensile test results on neutron-irradiated pure Fe, Fe-9Cr model alloy, 316 SS and CASS CF-8. These in situ experiments demonstrate the broad applications of the new capability in understanding several outstanding issues related to irradiated materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effects of Texture and Silica Content on Crack Growth in Boron Nitrides

Boron nitride is used in applications such as crucibles for melting and casting glasses and metals, insulators for furnaces, molds for hot pressing, and neutron absorbers. Historically, various grades of hot pressed hexagonal boron nitride (BN) have been used. This study investigates the fracture toughness and slow crack growth parameters of several commercially available BN grades. Prior work revealed that some grades of BN absorb water and change strength, thus presenting a philosophical conundrum on crack growth test methods. The grades selected for this study are of interest because their available billet size is sufficient for large components, or because they have heritage in specific applications. Ultimately, the data will be used to perform material selection, system design and reliability analyses of components of interest. Boron nitrides exhibit limited slow crack growth in humidity, with an orientation dependence due to crystallographic texture: orientations with van der Waal bonds are insensitive to water whereas those with covalent bonds are sensitive. Fracture toughness is low, around that of glass, and is also a function of orientation (bond type), with fracture occurring more readily along van der Waal bonds between hexagonal BN platelets than at covalent bonds across platelets. Silica additions toughen BN, but increase slow crack growth susceptibility.

Salem, Jonathan A.↗

High-entropy Al 0.3 CoCrFeNi alloy fibers with high tensile strength and ductility at ambient and cryogenic temperatures

High-entropy alloys (HEAs) are multi-component systems based on novel alloy composition designs with entropy maximization. They feature an array of unique mechanical properties when compared with traditional alloys. In this study, HEA fibers with diameters ranging from 1 to 3.15 mm in diameter, with the composition of Al 0.3 CoCrFeNi (atomic percent, at.%), were successfully fabricated by hot-drawing, followed by microstructural characterization using scanning-electron microscopy (SEM) and transmission-electron microscopy (TEM). The compositional variations within and between fibers were determined using energy-dispersive X-ray spectroscopy in TEM along with atomic-probe tomography (APT). These analyses revealed a homogeneous face-centered cubic (FCC) structure in the as-cast material, while post processing (e.g., forging and wire drawing) produced nanosized B2 particles in an FCC matrix. Electron back-scatter diffraction (EBSD) was used to determine the evolution of the texture and grain boundary character after processing of the fibers. The tensile strength and plasticity of the fibers were determined at both 298 K (1207 MPa/7.8%) and 77 K (1600 MPa/17.5%). Detailed TEM analyses revealed that the improvement of mechanical properties at 77 K (i.e. increased strength and ductility) is due to a change in deformation mechanisms from the planar slip of dislocations to nano-twinning. Such properties could be beneficial for cryogenic applications.

36 MATERIALS SCIENCE↗

Kinetics of photogenerated carbon dangling bonds in organic photovoltaic thin Films: An EPR study

Here, we report an investigation of the early kinetics of photogenerated carbon dangling bond (CDB) formation and annealing in organic photovoltaic bulk heterojunction (BHJ) thin film blends under oxygen- and moisture-free conditions, using X-band electron paramagnetic resonance (EPR) spectroscopy. The study focuses on donor:acceptor BHJ blends of PCE12:PCBM and PCE12:ITIC films, where PCE12 is PBDB-T. The time evolution of CDBs in such drop-cast BHJ films irradiated at 300 nm is monitored. The early kinetics of CDB formation, critical for understanding OPV degradation mechanisms, is studied. Theoretical analysis of the defect growth mechanism suggests a monomolecular defect creation model where the defect count follows a power-law t β with irradiation time t, where β ∼ 0.55–0.58, in excellent agreement with the theoretically expected value of β = 1/2. This model is compatible with CDB formation by the holes in donor sites adjacent to acceptors, likely assisted by energy released from quenching of nearby excitons by the holes, elucidating the physical mechanism underlying CDB formation. This is significant for designing improved materials, which mitigate defect creation, and consequently advancing the development of stable OPV systems.

42 ENGINEERING↗

Side Chain Engineering of Near-IR Aza-BODIPY Dyes Enables Processable Films with High Hole Mobility in Diodes

Boron chelated azadipyrromethene (Aza-BODIPY) derivatives are promising candidates for near-infrared optoelectronic applications due to their tunable absorption, electron-deficient core, and strong π-conjugation. Here, in this work, we synthesized and studied a series of 1-naphthylethynyl-substituted aza-BODIPY molecules featuring hexyl or hexyloxy solubilizing groups at either the proximal or the distal phenyl positions. These substitutions were designed to improve the solubility, film formation, and optoelectronic properties. We found that solubilizing groups not only enabled uniform solution-processed films but also fine-tuned key properties, such as absorption onset, oxidation potential, and energy levels. Charge transport analysis showed consistently high hole mobilities (∼10 –3 cm 2 /V s) across all substituted derivatives when CuI was used as the hole transport layer, regardless of film morphology. In contrast, electron mobilities tended to be low and inconsistent, partly because of the relatively poor-quality films on the ZnO electron transport layer. Overall, we have shown that solubilizing groups enable film solution-casting and can fine-tune the properties of these near-infrared aza-BODIPY derivatives.

36 MATERIALS SCIENCE↗

Modeling and simulation framework for dynamic strain localization in elasto-viscoplastic metallic materials subject to large deformations

This study describes a theoretical and computational framework for the treatment of adiabatic shear band formation in rate-sensitive polycrystalline metallic materials. From a computational perspective, accurate representation of strain localization behavior has been a long-standing challenge. In addition, the underlying physical mechanisms leading to the localization of plastic deformation are still not fully understood. The proposed framework is built around an enhanced-strain finite element formulation, designed to alleviate numerical pathologies known to arise in localization problems, by allowing a localization band of given finite width (weak discontinuity) to be embedded within individual elements. The mechanical threshold strength (MTS) model is used to represent the temperature and strain rate-dependent viscoplastic response of the material. This classical flow stress model employs an internal state variable to quantify the effect of dislocation structure evolution (work hardening and recovery). In light of growing evidence suggesting that the softening effect of dynamic recrystallization may play a significant role, alongside thermal softening, in the process of shear band formation and growth, a simple dynamic recrystallization model is proposed and cast within the context of the MTS model with the aid of the aforementioned internal state variable. An initiation criterion for shear localization in rate and temperature-sensitive materials is introduced and used in the present context of high-rate loading, where material rate-dependence is pronounced and substantial temperature increases are achieved due to the dissipative nature of viscoplastic processes. In addition, explicit time integration is adopted to facilitate treatment of the dynamic problems under consideration, where strain rates in excess of 10 4 s –1 are typically attained. Two series of experiments are conducted on AISI 316L stainless steel, employing the commonly used top-hat sample geometry and the Split-Hopkinson Pressure Bar dynamic test system. Axi-symmetric finite element simulation results are compared to cross-sectional micrographs of recovered samples and experimental load–displacement results, in order to examine the performance of the proposed framework and demonstrate its effectiveness in treating the initiation and growth of adiabatic shear banding in dynamically loaded metallic materials. These comparisons demonstrate that thermal softening alone is insufficient to induce shear localization behaviors observed in some materials, such as stainless steel, and support the hypothesis that dynamic recrystallization and/or other softening mechanisms play an essential role in this process.

36 MATERIALS SCIENCE↗

Affinity of LDR Organics to Cementitious Materials: Sorption and Leaching Tests

SRNL is working to identify and test the physiochemical interactions of organic contaminants of potential concern with minerals in grout/cementitious materials. Organic species may interact with cementitious minerals including slag, fly ash, cement, and other components/dopants like carbon in fly ash. The identification of such interactions will support the solidification process design, performance assessments for the chemicals of concern, and a proposed Resource Conservation and Recovery Act (RCRA) treatment variance the technology-based treatment standard specified for the Land Disposal Restriction (LDR) organics associated with Hanford tank waste. In FY24, a list of the 132 reasonably expected to be present LDR organics associated with Hanford tank waste (RPP-RPT-63493, Rev 1a) was screened by functional groups, octanol-water partitioning coefficients, and detection frequency in Hanford tank waste samples. A subset of 10 compounds spanning the identified properties were tested using sorption and leachate tests. These compounds were subject to traditional batch sorption tests and leaching tests on/from Cast Stone cementitious material with and without activated carbon (a potential organic adsorption additive). The tests have been completed and analysis is underway but as yet currently unavailable. The analytical results (and conclusions) will be included in a forthcoming revision to this report as soon as they are available

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

SYNTHESIS OF NOVEL ALL-DIELECTRIC GRATING FILTERS USING GENETIC ALGORITHMS

We are concerned with the design of inhomogeneous, all dielectric (lossless) periodic structures which act as filters. Dielectric filters made as stacks of inhomogeneous gratings and layers of materials are being used in optical technology, but are not common at microwave frequencies. The problem is then finding the periodic cell's geometric configuration and permittivity values which correspond to a specified reflectivity/transmittivity response as a function of frequency/illumination angle. This type of design can be thought of as an inverse-source problem, since it entails finding a distribution of sources which produce fields (or quantities derived from them) of given characteristics. Electromagnetic sources (electric and magnetic current densities) in a volume are related to the outside fields by a well known linear integral equation. Additionally, the sources are related to the fields inside the volume by a constitutive equation, involving the material properties. Then, the relationship linking the fields outside the source region to those inside is non-linear, in terms of material properties such as permittivity, permeability and conductivity. The solution of the non-linear inverse problem is cast here as a combination of two linear steps, by explicitly introducing the electromagnetic sources in the computational volume as a set of unknowns in addition to the material unknowns. This allows to solve for material parameters and related electric fields in the source volume which are consistent with Maxwell's equations. Solutions are obtained iteratively by decoupling the two steps. First, we invert for the permittivity only in the minimization of a cost function and second, given the materials, we find the corresponding electric fields through direct solution of the integral equation in the source volume. The sources thus computed are used to generate the far fields and the synthesized triter response. The cost function is obtained by calculating the deviation between the synthesized value of reflectivity/transmittivity and the desired one. Solution geometries for the periodic cell are sought as gratings (ensembles of columns of different heights and widths), or combinations of homogeneous layers of different dielectric materials and gratings. Hence the explicit unknowns of the inversion step are the material permittivities and the relative boundaries separating homogeneous parcels of the periodic cell.

Zuffada, Cinzia↗