Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Andreev reflection of quantum Hall states through a quantum point contact

Here, we investigate the interplay between the quantum Hall (QH) effect and superconductivity in InAs surface quantum well (SQW)/NbTiN heterostructures using a quantum point contact (QPC). We use QPC to control the proximity of the edge states to the superconductor. By measuring the upstream and downstream resistances of the device, we investigate the efficiency of Andreev conversion at the InAs/NbTiN interface. Our experimental data is analyzed using the Landauer Büttiker formalism, generalized to allow for Andreev reflection processes. We show that by varying the voltage of the QPC, V QPC , the average Andreev reflection, A, at the QH-SC interface can be tuned from 50% to ~ 10%. The evolution of A with V QPC extracted from the measurements exhibits plateaus separated by regions for which A varies continuously with V QPC . The presence of plateaus suggests that for some ranges of V QPC the QPC might be pinching off almost completely from the QH-SC interface some of the edge modes. Our work shows a new experimental setup to control and advance the understanding of the complex interplay between superconductivity and QH effect in two-dimensional gas systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Communication—Reduction of DC Resistance of Ni-Rich Lithium Transition Metal Oxide Cathode by Atomic Layer Deposition

A coating using Atomic layer deposition (ALD) of Al 2 O 3 was applied to Ni-rich lithium transition metal oxide cathode material. This ALD coating reduces the DC resistance (DCR) and increases the cycling performance of the Ni-rich cathode. Additionally, the reduced DCR comes from decreased solid electrolyte interphase (SEI) resistance on the anode, which is attributed to reduced transition metal deposition. This is due to the ALD coating preventing the direct contact between the cathode and the electrolyte, and therefore inhibits transition metal dissolution. This study suggests the promise of using ALD coating to reduce the DCR of Ni-rich cathode materials.

25 ENERGY STORAGE↗
NASA NTRS1989

The Pv product required for the frictional ignition of alloys

NASA-White Sands has developed a frictional heating tester capable of evaluating the ignition properties of alloys in oxygen under friction conditions which involve rubbing. Sixteen alloys have been thus evaluated, yielding determinations of the product of the contact pressure and surface speed required for ignition in oxygen at 6.9 MPa; those which contained large Ni fractions manifested the greatest resistance to rubbing-induced ignition. The effect of the coefficient of friction is noted to be a major influence on ignition, and the results obtained indicate the value of frictional heating tests for environments involving frictional heating.

Stoltzfus, Joel M.↗
NASA NTRS1993

Powder-Metallurgical Bearings For Turbopumps

Bearings fabricated by powder metallurgy developed for use in machines subjected to extremes of temperature, rolling-contact cyclic stresses, and oxidizing or otherwise corrosive fluids. Bearings also extend operating lives of other machines in which bearings required to resist extreme thermal, mechanical, and chemical stresses. One alloy exhibiting outstanding properties was MRC-2001. Resistance to fatigue, stress corrosion cracking, and wear found superior to that of 440C stainless steel.

Bhat, B. N.↗
NASA NTRS2003

Ceramic Strain Gages for Use at Temperatures up to 1500 Celsius

Indium-tin-oxide (ITO) thin film strain gages were successfully demonstrated at temperatures beyond 1500 C. High temperature static strain tests revealed that the piezoresistive response and electrical stability of the ceramic sensors depended on the thickness of the ITO films comprising the active strain elements. When 2.5 microns-thick ITO films were employed as the active strain elements, the piezoresistive response became unstable at temperatures above 1225 C. In contrast to this, ceramic sensors prepared with 5 microns-thick ITO were stable beyond 1430 C and sensors prepared with 8 microns-thick ITO survived more than 20 hr of operation at 1481 C. Very thick (10 microns) ITo strain gages were extremely stable and responsive at 1528 C. ESCA depth profiles confirmed that an interfacial reaction between the ITO strain gage and alumina substrate was responsible for the high temperature electrical stability observed. Similar improvements in high temperature stability were achieved by doping the active ITO strain elements with aluminum. Several Sic-Sic CMC constant strain beams were instrumented with ITO strain gages and delivered to NASA for testing. Due to the extreme surface roughness of the CMC substrates, new lithography techniques and surface preparation methods were developed. These techniques relied heavily on a combination of Sic and A12O3 cement layers to provide the necessary surface finish for efficient pattern transfer. Micro-contact printing using soft lithography and PDMS stamps was also used to successfully transfer the thin film strain gage patterns to the resist coated CMC substrates. This latter approach has considerable potential for transferring the thin film strain gage patterns to the extremely rough surfaces associated with the CMC's.

Gregory, Otto↗
DOE OSTI2020

Microstructure, hardness and cavitation erosion resistance of different cold spray coatings on stainless steel 316 for hydropower applications

There is an urgent need for repair of hydropower components that have undergone damage due to cavitation. Conventional repair methods involve melting of materials and can deteriorate material properties and cause distortion. This study investigated the relevant properties of different materials using solid phase processing—cold spray technology. Stainless steel (SS) 316, Inconel 625 and CrC-NiCr materials were cold spray deposited onto base metal SS 316, respectively. Cold spray achieved dense uniform deposits with low level porosity, and intimate contact between the deposit and the base metal was observed. Severe plastic deformation imparted during the cold spray process resulted in significant grain size refinement, nanostructured regions were observed in the deposits across the interfacial area. Cold sprayed deposits exhibited elevated hardness in contrast to that of the base metal SS 316. The cavitation erosion resistance of the deposits was evaluated with a cavitation erosion jet adhering to ASTM G134. Both SS 316 and Inconel 625 achieved better cavitation erosion resistance when compared to that of the SS 316 base metal, with the former exhibiting close to a 4 times improvement.

Jiang, Xiujuan↗
NASA NTRS1985

Impact wear of iron rich superalloys

The impact-sliding wear resistance of chill cast and aligned eutectic Fe-base superalloys against M42 and 17-4 PH steel counterface materials is examined. The aligned material tests were run with carbide fibers perpendicular to the counterface contact surface and the characterization focused on fracture processes as observed in the subsurface microstructure of the worn materials. Metallographic analyses were performed on specimens exposed to various numbers of repetitive impact load cycles, and for comparison, two other aligned composites were tested with the same fiber orientation under identical test conditions against hardened M42 tool steel. A strong improvement was found in wear resistance of an aligned eutectic structure as compared to the corresponding randomized chill cast structure. Experiments with the softer 17-4 counterface were characterized by transfer onto the Fe-base superalloy, and the cracks formed were oriented transverse to the relative sliding direction and occurred in a periodic fashion. Observations in subsurface regions of the worn materials indicated crack intergranularity with an occasional transgranular fracture of the M7C3 carbide phase.

Wayne, S. F.↗
DOE OSTI2022

Explanation and Application of the Evolving Contact Traction Fields in Shallow Foundation Systems

The present paper provides a qualitative discussion of the evolution of contact traction fields beneath rigid shallow foundations resting on granular materials. A phenomenological similarity is recognized in the measured contact traction fields of rigid footings and at the bases of sandpiles. This observation leads to the hypothesis that the stress distributions are brought about by the same physical phenomena, namely the development of arching effects through force chains and mobilized intergranular friction. A set of semi-empirical equations are suggested for the normal and tangential components of this contact traction based on past experimental measurements and phenomenological assumptions of frictional behaviors at the foundation system scale. These equations are then applied to the prescribed boundary conditions for the analysis of the settlement, resistance, and stress fields in supporting granular materials beneath the footing. A parametric sensitivity study is performed on the proposed modelling method, highlighting solutions to the boundary-value problems in an isotropic, homogeneous elastic half-space.

42 ENGINEERING↗
DOE OSTI2022

Avoiding CO 2 Improves Thermal Stability at the Interface of Li 7 La 3 Zr 2 O 12 Electrolyte with Layered Oxide Cathodes

Abstract Solid‐state batteries promise higher energy densities and better safety than Li‐ion batteries with liquid electrolytes. However, the interface between solid electrolyte and cathode is unstable at the elevated temperatures that are needed while sintering to achieve good bonding between ceramic components. Here, the hypothesis is that, the gas environment, especially the presence of CO 2, is critical in determining the stability of the solid electrolyte–cathode interface. The effect of gas species on the interface is systematically probed, by a using Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte with a thin film LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode as a model system to enable interface sensitivity. Detrimental phases formed at the interface and their onset conditions are identified by X‐ray absorption spectroscopy, X‐ray diffraction, and Gibbs free energy analysis. As a result, removing CO 2 and minimizing H 2 O(g) during sintering is necessary to obtain good contact at the LLZO|cathode interface without forming secondary phases. Sintering in O 2 is ideal, yielding excellent chemical stability and low interfacial resistance. Secondary phases also do not form in N 2, but oxygen loss occurs at elevated temperatures. The interfacial resistance obtained upon sintering in pure O 2 is comparable to the lowest values at LLZO interfaces with protective coatings, but here without the need for interface coatings.

25 ENERGY STORAGE↗
DOE OSTI2023

Reaction Current Heterogeneity at the Interface between a Lithium Electrode and Polymer/Ceramic Composite Electrolytes

Although lithium metal anodes are expected to increase the energy density of next-generation batteries, dendrite growth during charge remains a major bottleneck preventing widespread implementation. Composite solid electrolytes with ceramic particles embedded in a polymer matrix have the potential to prevent dendrites owing to the higher mechanical stiffness while also possessing the flexibility to maintain contact with the electrode. However, microscopically, the different mechanical and electrochemical properties of the polymer and ceramic domains can cause inhomogeneous charge transfer at the Li/electrolyte interface, which can lead to nonuniform Li deposition and propagation of dendrites. Here, we computationally examine the coupled electrochemical, transport, and mechanical processes at the interface to determine the propensity for dendrite formation and possible approaches to mitigate this issue. Predictions of two possible microstructures at the interface, namely, (i) where both the polymer and ceramic come in contact with Li metal and (ii) when only the polymer comes in contact with Li metal, suggest that the former has a greater tendency for nonuniform plating. In addition, predictions suggest that minimizing the interfacial resistance between polymers and ceramics and incorporating interlayers between the electrode and electrolyte help mitigate current heterogeneity. In conclusion, these predictions provide guidance for experimental approaches to prevent dendrites in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Size-Controlled Nanoparticles Embedded in a Mesoporous Architecture Leading to Efficient and Selective Hydrogenolysis of Polyolefins

A catalytic architecture, comprising a mesoporous silica shell surrounding platinum nanoparticles (NPs) supported on a solid silica sphere (mSiO2/Pt-X/SiO2; X is the mean NP diameter), catalyzes hydrogenolysis of melt-phase polyethylene (PE) into a narrow C23-centered distribution of hydrocarbons in high yield using very low Pt loadings (~10 -5 g Pt/g PE). During catalysis, a polymer chain enters a pore and contacts a Pt NP where the C–C bond cleavage occurs and then the smaller fragment exits the pore. mSiO 2 /Pt/SiO 2 resists sintering or leaching of Pt and provides high yields of liquids; however, many structural and chemical effects on catalysis are not yet resolved. Here, we report the effects of Pt NP size on activity and selectivity in PE hydrogenolysis. Time-dependent conversion and yields and a lumped kinetics model based on the competitive adsorption of long vs short chains reveal that the activity of catalytic material is highest with the smallest NPs, consistent with a structure-sensitive reaction. Remarkably, the three mSiO 2 /Pt-X/SiO 2 catalysts give equivalent selectivity. We propose that mesoscale pores in the catalytic architecture template the C 23 -centered distribution, whereas the active Pt sites influence the carbon–carbon bond cleavage rate. This conclusion provides a framework for catalyst design by separating the C–C bond cleavage activity at catalytic sites from selectivity for chain lengths of the products influenced by the structure of the catalytic architecture. The increased activity, selectivity, efficiency, and lifetime obtained using this architecture highlight the benefits of localized and confined environments for isolated catalytic particles under condensed-phase reaction conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1975

Advances in the theory and application of BSF cells

The characteristics and behavior of p(+), p solar cells were investigated. The p(+), p cells were made by the removal of the n(+) surface layers from n(+), p p(+), BSF cells followed by application of a suitable contact to the resultant p(+), p structures. The open circuit voltage of p(+), p cells was found to increase with increasing 'p' bulk resistivity. The measured open circuit velocity-temperature coefficients were positive and increased with increasing resistivity. An outline of prior limitations in solar cell design is presented, and the removal of these limitations through use of BSF effects is pointed out. The study of BSF effects made feasible production of very thin high efficiency silicon cells as well as high resistivity-high efficiency cells, two desirable types of silicon cells which were previously impossible to make.

Mandelkorn, J.↗
NASA NTRS1979

Limiting process in shallow junction solar cells

In extending the violet and nonreflective cell technology to lower resistivities, several processes limiting output power were encountered. The most important was the dark diffusion current due to recombination at the front grid contacts. After removal of this problem by reduction of the silicon metal contact area (to 0.14 percent of the total area), the electric field enhanced junction recombination current J sub r was the main limitation. Alteration of the diffusion profile to reduce the junction field is shown to be an effective means of influencing J sub r. The remaining problems are the bulk recombination in the n+ layer and the surface recombination at the oxide-silicon interface; both of these problems are aggravated by band-narrowing resulting from heavy doping in the diffused layer. Experimental evidence for the main limitations is shown, where increased diffusion temperature is seen to reduce both the influence of the front grid contacts and the junction electric field by increasing the junction depth. The potential for further significant improvement in efficiency appears to be high.

Meulenberg, A.↗
NASA NTRS1989

Sequentially evaporated thin Y-Ba-Co-O superconducting films on microwave substrates

The development of high T sub c superconducting thin films on various microwave substrates is of major interest in space electronic systems. Thin films of YBa2Cu3O(7-Delta) were formed on SrTiO3, MgO, ZrO2 coated Al2O3, and LaAlO3 substrates by multi-layer sequential evaporation and subsequent annealing in oxygen. The technique allows controlled deposition of Cu, BaF2 and Y layers, as well as the ZrO buffer layers, to achieve reproducibility for microwave circuit fabrication. The three layer structure of Cu/BaF2/Y is repeated a minimum of four times. The films were annealed in an ambient of oxygen bubbled through water at temperatures between 850 C and 900 C followed by slow cooling (-2 C/minute) to 450 C, a low temperature anneal, and slow cooling to room temperature. Annealing times ranged from 15 minutes to 5 hrs. at high temperature and 0 to 6 hr. at 450 C. Silver contacts for four probe electrical measurements were formed by evaporation followed with an anneal at 500 C. The films were characterized by resistance-temperature measurements, energy dispersive X-ray spectroscopy, X-ray diffraction, and scanning electron microscopy. Critical transition temperatures ranged from 30 K to 87 K as a function of the substrate, composition of the film, thicknesses of the layers, and annealing conditions. Microwave ring resonator circuits were also patterned on these MgO and LaAlO3 substrates.

Valco, G. J.↗
NASA NTRSDate not supplied

Using Holey Graphene for Improved Interfacial Contact in Solid Electrolyte Ionic Conductivity Measurements

Solid-state batteries (SSBs) are poised to become the batteries of the future with advantages such as higher energy density, lighter weight, versatile geometry, and greater safety due to low flammability risk. An important parameter of the solid electrolyte (SE) used is its ionic conductivity. The ionic conductivity is generally calculated from the bulk resistance of a SE pellet, measured from the electrochemical impedance spectroscopy data. The SE pellet is typically prepared from the electrolyte powder by dry compression and is sandwiched between two blocking current collectors to obtain the impedance spectroscopy data. One of the challenges in conducting this measurement is poor interfacial contacts between the SE pellet and the current collector surfaces. Therefore, measurements reported in the literature may underestimate the true ionic conductivity of a given electrolyte. Holey graphene is a carbon nanomaterial with high electrical conductivity and unique dry compressibility, which is unusual for carbon materials but similar to many oxide and sulfide SEs. In this work, it is demonstrated that adding a thin layer of holey graphene between the electrolyte and the stainless steel current collectors significantly improves the interfacial contact. The ionic conductivity values obtained in the effort were sometimes several times higher than the data measured for SEs without the holey graphene layers. This work calls for more standardized measurement procedures to reduce the discrepancies in reported ionic conductivity values.

Solid state battery↗
NASA NTRS1993

Stability of the Halley cometosheath with resistivity and plasma motion

The MHD stability of the cometary inner sheath determined by the balance between the inward Lorentz body force and the outward ion-neutral drag force is investigated by numerically solving the wave equations which include resistivity, plasma motion and plasma pressure with the help of two-point boundary value method. The eigenvalues and the eigenfunctions are obtained numerically by treating the cometary inner sheath as a layer of finite thickness, bounded by the contact surface, that is, the diamagnetic cavity boundary. To gain insight into the problem, certain limiting cases of the wave equations are also discussed. The diamagnetic cavity boundary and the adjacent layer of about 100-km thickness of Comet Halley is found to be unstable. The effects of finite plasma pressure, dissociative recombination, mass loading due to photoionization, resistivity, and plasma motion are found to be stabilizing but are unable to quench the instability completely. Motion of the Halley ionopause has been confirmed by observations.

Srivastava, Krishna M.↗
DOE OSTI2020

Isolating p- and n-Doped Fingers With Intrinsic Poly-Si in Passivated Interdigitated Back Contact Silicon Solar Cells

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts enable ultra high efficiency interdigitated back contact silicon solar cells. To prevent shunt between n- and p-type doped fingers, an insulating region is required between them. We evaluate the use of intrinsic poly Si for this isolation region. Interdigitated fingers were formed by plasma deposition of doped hydrogenated amorphous silicon through mechanically aligned shadow masks, on top of a full-area intrinsic amorphous silicon layer. High temperature annealing then crystallized the a-Si:H to poly Si and drove in the dopants. Two mechanisms were identified which cause contamination of the intrinsic poly Si gap during processing. During deposition of doped fingers, we show using secondary ion mass spectrometry and conductivity measurements that the intrinsic gap becomes contaminated by doped a-Si:H tails several nanometers thick to concentrations of ~10 20 cm -3 . Another source of contamination occurs during high-temperature annealing, where dopants desorb from doped regions and readsorb onto intrinsic a Si:H. Both pathways reduce the resistivity of the intrinsic gap from ~10 5 Ω·cm to ~10 -1 Ω·cm. We show that plasma etching of the a-Si:H surface before crystallizing with a capping layer can eliminate the contamination of the intrinsic poly-Si, maintaining a resistivity of ~10 5 Ω·cm. Lastly, this demonstrates masked plasma deposition as a dopant patterning method for Si solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Near-Field Corrosion Interactions between Glass and Corrosion Resistant Alloys

This study explores the corrosion interactions between model nuclear waste glass materials and corrosion resistant alloys, under conditions that simulate the near field of a nuclear waste repository. The interactions between the corrosion of stainless steel (SS) 316, alloy G30, or alloy 625, and international simple glass or soda-lime silica glass are systematically studied. The dissimilar materials were exposed in close proximity to each other in different electrolytes at 90 oC. After exposure, the glass surface exposed near metals showed different regimes of corrosion, with distinct surface morphologies and chemistries that were likely affected by the local environment created by the localized corrosion of metals. Surface and solution analyses showed that the corrosion rate of glass was enhanced by the presence of metals. Infrared spectroscopy data suggested the local build-up of stresses in the contact area of glass, which may lead to the mechanical instability of the glass alteration layer. On the other hand, the effect of glass on metal corrosion is strongly dependent on the leaching solution. In electrolytes containing abundant aggressive anions such as Cl-, glass seems to suppress the localized corrosion of SS by the precipitation of a Si-rich surface film that protects the SS substrate from solutions. However, in less aggressive electrolytes, the corrosion rate of SS was increased by the presence of glass corrosion products. Overall, our study showed that the hidden and localized damage on glass in contact with metals may enhance the release of incorporated radionuclides compared to typical uniform glass corrosion. Therefore, more attention should be paid to the corrosion interactions between metals and glass under repository conditions.

Guo, Xiaolei↗