Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CASTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Interface Analyses Between a Case-Hardened Ingot Casting Steel and Carbon-Containing and Carbon-Free Refractories

Corrosion tests of carbon-free and carbon-containing refractories were performed. The carbon-free crucibles corroded, whereas the carbon-containing crucibles were negligibly attacked. On them, inclusions were attached. This study investigates melt oxygen contents, interface properties, and steel compositions with their non-metallic inclusions in order to explore the inclusion formation and deposition mechanisms. The carbon-free crucibles were based on alumina, mullite, and zirconia- and titania-doped alumina (AZT). The carbon-containing (-C) ones were alumina-C and AZT-C. Furthermore, nanoscaled carbon and alumina additives (-n) were applied in an AZT-C-n material. In the crucibles, the case-hardened steel 17CrNiMo7-6 was remelted at 1580 °C. It was observed that the melt and steel oxygen contents were higher for the tests in the carbon-free crucibles. Into these crucibles, the deoxidizing alloying elements Mn and Si diffused. Reducing contents of deoxidizing elements resulted in higher steel oxygen levels and less inclusions, mainly of the inclusion group SiO 2 -core-MnS-shell (2.5 to 8 μm). These developed from smaller SiO 2 nuclei. The inclusion amount in the steel was highest after remelting in AZT-C-n for 30 minutes but decreased strongly with increasing remelting time (60 minutes) due to inclusions’ deposition on the refractory surface. The Ti from the AZT and the nanoadditives supported inclusion growth and deposition. Other inclusion groups were alumina and calcium aluminate inclusions. Their contents were high after remelting in carbon- or AZT-containing crucibles but generally decreased during remelting. On the AZT-C-n crucible, a dense layer formed from vitreous compositions including Al, Ca, Mg, Si, and Ti. To summarize, for reducing forming inclusion amounts, mullite is recommended as refractory material. For capturing formed inclusions, AZT-C-n showed a high potential.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Analysis of Meniscus Fluctuation in a Continuous Casting Slab Mold

A water model of slab mold was established to analyze the microscopic and macroscopic fluctuation of meniscus. The fast Fourier transform and wavelet entropy were adopted to analyze the wave amplitude, frequency, and components of fluctuation. The flow patterns under the meniscus were measured by using particle image velocimetry measurement and then the mechanisms of meniscus fluctuation were discussed. The results reflected that wavelet entropy had multi-scale and statistical properties, and it was suitable for the study of meniscus fluctuation details both in time and frequency domain. The basic wave, frequency of which exceeding 1 Hz in the condition of no mold oscillation, was demonstrated in this work. In fact, three basic waves were found: long-wave with low frequency, middle-wave with middle frequency, and short-wave with high frequency. In addition, the upper roll flow in mold had significant effect on meniscus fluctuation. When the position of flow impinged was far from the meniscus, long-wave dominated the fluctuation and the stability of meniscus was enhanced. However, when the velocity of flow was increased, the short-wave dominated the meniscus fluctuation and the meniscus stability was decreased.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Size Distribution of Graphite Nodules in Hypereutectic Cast Irons of Varying Nodularity

An SGI was machined into 400 g cylindrical pieces and remelted in an electrical resistance furnace protected by Ar gas to produce materials ranging from SGI to CGI. The graphite morphology was controlled by varying the holding time at 1723 K (1450 °C) between 10 and 60 minutes. The discrete sectional size distribution of nodules by number density was measured on cross sections of the specimens and translated to volumetric distribution by volume fraction. Subpopulations of nodules were distinguished by fitting Gaussian distribution functions to the measured distribution. Primary and eutectic graphite, were found to account for most of the volume of nodular graphite in all cases. For holding times of 40 minutes and greater, corresponding to nodularity roughly below 40 pct, the primary subpopulation was very small and difficult to distinguish, leaving eutectic nodules as the dominant subpopulation. The mode and standard deviation of the two subpopulations were roughly independent of nodularity. Moreover, the nodular and vermicular graphite were segregated in the microstructure. In conclusion, the results suggest that the parallel development of the vermicular eutectic had small influence on the size distribution of eutectic graphite nodules.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Similarity Criteria for the Study of Removal of Spherical Non-metallic Inclusions in Physical Models of Continuous Casting Tundishes: A More Fundamental Approach

Physical modeling is widely used for studying steelmaking processes. The accuracy of this technique depends on the use of appropriate similarity criteria during experimental design. The present work deduced rigorously the similarity criteria for the study of spherical non-metallic inclusions in isothermal physical models of tundishes. Initially, macroscopic quantities were used to simplify the multiphase problem. Then, the similarity criteria were obtained from the dimensionless form of the exact equation of motion for an inclusion in Stokes regime. The validity range of these criteria was discussed and they were compared with common literature practice. Some practical considerations were also presented. This work clarifies various implicit assumptions usually adopted in literature. Additionally, a restrictive criterion to choose the density of the inclusion simulating particles was obtained, which can be satisfied, for example, by hollow glass particles in water models. This criterion is necessary to adequately describe the inclusion motion in regions where fluid elements suffer strong acceleration (e.g., inside nozzles, near flow controllers or in the entering fluid jet). Moreover, it was established an upper limit for the concentration of particles injected in the inlet nozzle of physical models, which do not simulate the phenomenon of inclusion aggregation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

High Chromium Cast Irons: Destabilized-Subcritical Secondary Carbide Precipitation and Its Effect on Hardness and Wear Properties

This work evaluates the effect of a destabilization treatment combined with a subcritical diffusion (SCD) and a subsequent quenching (Q) steps on precipitation of secondary carbides and their influence on the wear properties of HCCI (16%Cr). The destabilization of the austenite at high temperature leads to a final microstructure composed of eutectic and secondary carbides, with an M{sub 7}C{sub 3} nature, embedded in a martensitic matrix. An improved wear resistance was observed in the SCD + Q samples in comparison with the Q one, which was attributed to the size of secondary carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Solidification Characteristics of Silicon-Alloyed Ductile Cast Irons

Solidification pattern of three ductile iron compositions [I-2.5%Si; II-4%Si, and III-4%Si-1.6%Mo] is studied, to evaluate the effects of high Si and Mo contents. Inoculation compensates for the negative effect of Mo on eutectic undercooling. The deviation using a sphere as reference of graphite particles is noticeably increased by silicon alloying, when a characteristic of the graphite particles appears have a larger perimeter, resulting in a large category [IV, V and VI forms, ISO 945]. The sphericity shape factor (SSF) considering the real perimeter of particle is recommended in the nodularity evaluation in high-Si ductile iron, instead of the roundness shape factor, involving maximum ferret, presently incorporated in the ISO 945 standard. The higher the minimum acceptable SSF is, the greater difference in nodularity, between conventional and Si-alloyed ductile irons. For more than 4%Si, ductile irons are characterized by a medium-quality graphite phase, with prevalent form V-ISO 945 graphite. A specific inoculant, with a powerful action on the graphite particle compactness, especially to promote VI graphite form, is necessary.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Nano-scale orientation mapping of graphite in cast irons

A diametrical section of a graphite spheroid from a ductile iron sample was prepared using the focused ion beam-lift out technique. Characterization of this section was carried out through automated crystal orientation mapping in a transmission electron microscope. This new technique automatically collects electron diffraction patterns and matches them with precalculated templates. The results of this investigation are crystal orientation and phase maps of the specimen, which bring new light to the understanding of growth mechanisms of this peculiar graphite morphology. This article shows that mapping the orientation of carbon-based materials such as graphite, which is difficult to achieve with conventional techniques, can be performed automatically and at high spatial resolution using automated crystal orientation mapping in a transmission electron microscope. - Highlights: • ACOM/TEM can be used to study the crystal orientation of carbon-based materials. • A spheroid is formed by conical sectors radiating from a central nuclei. • Misorientations exist within the conical sectors, defining various orientation domains.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of boron addition on the morphology of silicon phases in Al-Si casting alloys

Highlights: • The influence of boron on Si phase was studied. • Boron addition reduces the length of eutectic Si plates in Al-11Si alloys. • Boron addition promotes the nucleation temperature of primary Si phases in Al-14Si alloys. • Boron addition increases the twin density in the <112>{sub Si} growth direction of eutectic Si in Al-11Si and Al-14Si alloys. - Abstract: The influence of B elements on the morphology of Si phases in Al-11Si and Al-14Si alloys has been investigated employing Optical Microscope, Scanning Electron Microscopy, Transmission Electron Microscopy and Differential Scanning Calorimetry. In Al-11Si alloy, the addition of B element not only refines the primary Al dendrites, but also reduces the length of eutectic Si plates. In Al-14Si alloys, the addition of B element promotes the nucleation temperature of primary Si phases, but shows weak influence on the nucleation temperature of eutectics. The effects of B element on the morphologies of both primary Si particle and eutectics can be attributed to the interaction between B and Si elements during the solidification process.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Freeze-casting as a Novel Manufacturing Process for Fast Reactor Fuels. Final Report

Advanced burner reactors are designed to reduce the amount of long-lived radioactive isotopes that need to be disposed of as waste. The input feedstock for creating advanced fuel forms comes from either recycle of used light water reactor fuel or recycle of fuel from a fast burner reactor. Fuel for burner reactors requires novel fuel types based on new materials and designs that can achieve higher performance requirements (higher burn up, higher power, and greater margins to fuel melting) then yet achieved. One promising strategy to improved fuel performance is the manufacture of metal or ceramic scaffolds which are designed to allow for a well-defined placement of the fuel into the host, and this in a manner that permits greater control than that possible in the production of typical CERMET fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Feasibility Study for Electrical Discharge Machining of Large DU-Mo Castings

U-10 wt. % Mo (U-10Mo) alloys are being developed as low enrichment monolithic fuel for the CONVERT program. Optimization of processing for the monolithic fuel is being pursued with the use of electrical discharge machining (EDM) under CONVERT HPRR WBS 1.2.4.5 Optimization of Coupon Preparation. The process is applicable to manufacturing experimental fuel plate specimens for the Mini-Plate-1 (MP-1) irradiation campaign. The benefits of EDM are reduced machining costs, ability to achieve higher tolerances, stress-free, burr-free surfaces eliminating the need for milling, and the ability to machine complex shapes. Kerf losses are much smaller with EDM (tenths of mm) compared to conventional machining (mm). Reliable repeatability is achievable with EDM due to its computer-generated machining programs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗