Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aerodynamic Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Computational Aeroheating Predictions for Mars Lander Configurations

The proposed Mars Science Laboratory (MSL) mission is intended to deliver a large rover to the Martian surface within 10 km of the target site. This paper presents computational fluid dynamics (CFD) predictions of forebody heating rates for two MSL entry configurations with fixed aerodynamic trim tabs. Results are compared to heating on a 70-deg sphere-cone reference geometry. All three heatshield geometries are designed to trim hypersonically at a 16 deg angle of attack in order to generate the lift-to-drag ratio (LID) required for precision landing. Comparisons between CFD and tunnel data are generally in good agreement for each configuration, but the computations predict more flow separation and higher heating on a trim tab inclined 10 deg relative to the surface. CFD solutions at flight conditions were obtained using an 8-species Mars gas in chemical and thermal non-equilibrium. Laminar and Baldwin-Lomax solutions were used to estimate the effects of the trim tabs and turbulence on heating. A tab extending smoothly from the heatshield flank is not predicted to increase laminar or turbulent heating rates above the reference levels. Laminar heating on a tab deflected 10 deg from the conical heatshield is influenced by flow separation and is up to 35% above the baseline heating rate. The turbulent solution on the inclined tab configuration predicts attached flow and a 43% heating increase above the reference level.

Edquist, Karl T.↗
NASA NTRS2003

Computational Aeroheating Predictions for Mars Lander Configurations

The proposed Mars Science Laboratory (MSL) mission is intended to deliver a large rover to the Martian surface within 10 km of the target site. This paper presents computational fluid dynamics (CFD) predictions of forebody heating rates for two MSL entry configurations with fixed aerodynamic trim tabs. Results are compared to heating on a 70-deg sphere-cone reference geometry. All three heatshield geometries are designed to trim hypersonically at a 16 deg angle of attack in order to generate the lift-to-drag ratio (L/D) required for precision landing. Comparisons between CFD and tunnel data are generally in good agreement for each configuration, but the computations predict more flow separation and higher heating on a trim tab inclined 10 deg relative to the surface. CFD solutions at flight conditions were obtained using an 8-species Mars gas in chemical and thermal nonequilibrium. Laminar and Baldwin-Lomax solutions were used to estimate the effects of the trim tabs and turbulence on heating. A tab extending smoothly from the heatshield flank is not predicted to increase laminar or turbulent heating rates above the reference levels. Laminar heating on a tab deflected 10 deg from the conical heatshield is influenced by flow separation and is up to 35% above the baseline heating rate. The turbulent solution on the inclined tab configuration predicts attached flow and a 43% heating increase above the reference level.

Edquist, Karl T.↗
NASA NTRS1986

Application of program LAURA to three-dimensional AOTV flowfields

Program LAURA (Langley Aerothermodynamic Upwind Relaxation Algorithm) is a robust, finite volume, single-level storage, implicit upwind differencing algorithm which has been documented and tested on several three-dimensional blunt-body flows. The algorithm can run at unlimited Courant numbers (relaxing the steady-state equations) but requires the inversion of only a 5 x 5 matrix per computational cell. An alternating directional sweep Gauss-Seidel substitution strategy is used to relax the governing equations. At present, the Euler and thin-layer Navier-Stokes equations using Sutherland's law for viscosity have been modeled for a perfect gas, equilibrium air, and nonequilibrium air chemistry neglecting diffusion. The equilibrium and nonequilibrium air chemistry options have been described in a companion paper. Good comparisons with experimental data and another calculation method for pressure distributions, aerodynamic coefficients, and heat-transfer distributions have been demonstrated for three-dimensional blunt-body flows.

Gnoffo, P. A.↗
NASA NTRS1987

Utilization of Global Reference Atmosphere Model (GRAM) for shuttle entry

At high latitudes, dispersions in values of density for the middle atmosphere from the Global Reference Atmosphere Model (GRAM) are observed to be large, particularly in the winter. Trajectories have been run from 28.5 deg to 98 deg. The critical part of the atmosphere for reentry is 250,000 to 270,000 ft. 250,000 ft is the altitude where the shuttle trajectory levels out. For ascending passes the critical region occurs near the equator. For descending entries the critical region is in northern latitudes. The computed trajectory is input to the GRAM, which computes means and deviations of atmospheric parameters at each point along the trajectory. There is little latitude dispersion for the ascending passes; the strongest source of deviations is seasonal; however, very wide seasonal and latitudinal deviations are exhibited for the descending passes at all orbital inclinations. For shuttle operations the problem is control to maintain the correct entry corridor and avoid either aerodynamic skipping or excessive heat loads.

Joosten, Kent↗
NASA NTRS1986

Boundary layer measurements using hot-film sensors

Measurements in the aerodynamic boundary layer using heat transfer, hot-film sensors are receiving a significant amount of effort at the Langley Research Center. A description of the basic sensor, the signal conditioning employed, and several manifestations of the sensor are given. Results of a flow reversal sensor development are presented, and future work areas are outlined.

Holmes, Harlan K.↗
NASA NTRS1988

Application of integrated fluid-thermal-structural analysis methods

Hypersonic vehicles operate in a hostile aerothermal environment which has a significant impact on their aerothermostructural performance. Significant coupling occurs between the aerodynamic flow field, structural heat transfer, and structural response creating a multidisciplinary interaction. Interfacing state-of-the-art disciplinary analysis methods is not efficient, hence interdisciplinary analysis methods integrated into a single aerothermostructural analyzer are needed. The NASA Langley Research Center is developing such methods in an analyzer called LIFTS (Langley Integrated Fluid-Thermal-Structural) analyzer. The evolution and status of LIFTS is reviewed and illustrated through applications.

Wieting, Allan R.↗
NASA NTRS1988

Application of integrated fluid-thermal structural analysis methods

Hypersonic vehicles operate in a hostile aerothermal environment which has a significant impact on their aerothermostructural performance. Significant coupling occurs between the aerodynamic flow field, structural heat transfer, and structural response creating a multidisciplinary interaction. Interfacing state-of-the-art disciplinary analysis methods are not efficient, hence interdisciplinary analysis methods integrated into a single aerothermostructural analyzer are needed. The NASA Langley Research Center is developing such methods in an analyzer called LIFTS (Langley Integrated Fluid-Thermal-Structural) analyzer. The evolution and status of LIFTS is reviewed and illustrated through applications.

Wieting, Allan R.↗
NASA NTRS1991

Three-dimensional rarefied flow simulations for the Aeroassist Flight Experiment vehicle

Hypersonic rarefied flow about the Aeroassist Flight Experiment vehicle has been investigated using a three-dimensional direct simulation Monte Carlo method. Calculations are performed for the transitional flows encountered during the vehicle's atmospheric entry for altitudes of 110 and 100 km with an entry velocity of 9.9 km/s. The simulations are performed using a five-species reacting gas model that account for rotational and vibrational internal energies. The solutions indicate that dissociation is important at altitudes of 110 km and below. Results are presented for surface pressures, convective heating, flowfield structure, and aerodynamic coefficient variations with altitude.

Celenligil, M. Cevdet↗
NASA NTRS1991

Hypersonic rarefied flow about a delta wing - Direct simulation and comparison with experiment

Three-dimensional simulations of hypersonic rarefied flow about a delta wing are made using the direct simulation Monte Carlo (DSMC) method of Bird, and the results of the computations are compared with recent experimental data obtained in a vacuum wind tunnel at the DLR in Gottingen, Germany. The present study considers Mach 8.89 nitrogen flow for a range of conditions that include Knudsen numbers of 0.016 to 3.505 for an incidence angle of 30 deg, and angles of incidence of 15 to 60 deg for a constant Knudsen number of 0.389. The calculations provide details concerning the flowfield structure and surface quantities. Comparisons between the calculations and the available experimental measurements are made for aerodynamic and overall heat-transfer coefficients and recovery temperature. The agreement between the measured and calculated data are very good, well within the estimated measurement uncertainty. Comparisons are also made with modified Newtonian and free-molecule theories.

Celenligil, M. C.↗
NASA NTRS1992

Postflight aerothermodynamic analysis of Pegasus(tm) using computational fluid dynamic techniques

The objective was to validate the computational capability of the NASA Ames Navier-Stokes code, F3D, for flows at high Mach numbers using comparison flight test data from the Pegasus (tm) air launched, winged space booster. Comparisons were made with temperature and heat fluxes estimated from measurements on the wing surfaces and wing-fuselage fairings. Tests were conducted for solution convergence, sensitivity to grid density, and effects of distributing grid points to provide high density near temperature and heat flux sensors. The measured temperatures were from sensors embedded in the ablating thermal protection system. Surface heat fluxes were from plugs fabricated of highly insulative, nonablating material, and mounted level with the surface of the surrounding ablative material. As a preflight design tool, the F3D code produces accurate predictions of heat transfer and other aerodynamic properties, and it can provide detailed data for assessment of boundary layer separation, shock waves, and vortex formation. As a postflight analysis tool, the code provides a way to clarify and interpret the measured results.

Kuhn, Gary D.↗
NASA NTRS1991

Aerobrake aerothermodynamic environment predictions in support of the Aeroassist Flight Experiment

A computational fluid dynamic (CFD) simulation of the flow past an Aeroassist Flight Experiment (AFE) aerobrake under wind tunnel test conditions has been made. The Navier-Stokes equations in three dimensions were solved numerically using a finite-volume, implicit approach. Comparisons with experimental data include surface pressures and heat transfer rates and aerodynamic coefficients. Agreement with experiment is shown to be excellent. The dependence of the solution on the computational grid is explored. The present work is preliminary to simulation of the flow past the AFE under flight conditions, which at present cannot be duplicated with ground-based experimental facilities.

Fay, John F.↗
NASA NTRS1993

Simulated rarefied aerodynamics of the Magellan spacecraft during aerobraking

Aerodynamic loads upon the Magellan spacecraft during aerobraking through the atmosphere of Venus are computed at off-design attitudes with a direct simulation Monte Carlo (DSMC) particle method. Simulated rarefied flows at nominal altitudes near 140 km and an entry speed of 8.6 km/s were compared to simulated and analytic free molecular results. Aerodynamic moments, forces, and heating for rarefied entry at all attitudes were 7-10 percent below free molecular results. All moments acted to restore the vehicle to its nominal zero-pitch, zero-yaw attitude. Suggested canting of the solar panels is an innovative configuration to assess gas-surface interaction during aerobraking. The resulting roll torques about the central body-axis as predicted in rarefied flow simulations were nearly twice that predicted for free molecular flow, although differences became less distinct for thermal accommodation coefficients well below unity. Roll torques increased dramatically with reduced accommodation coefficients employed in the simulation. In the DSMC code, periodic free-molecule boundary conditions and a coarse computational grid and body resolution served to minimize the simulation size and cost while retaining solution validity.

Haas, Brian L.↗
NASA NTRS1953

Pressure Distributions About Finite Wedges in Bounded and Unbounded Subsonic Streams

An analytical investigation of incompressible flow about wedges was made to determine effects of tunnel-wedge ratio and wedge angle on the wedge pressure distributions. The region of applicability of infinite wedge-type velocity distribution was examined for finite wedges. Theoretical and experimental pressure coefficients for various tunnel-wedge ratios, wedge angles, and subsonic Mach numbers were compared.

FLOW, LAMINAR↗
NASA NTRS1957

Theory and Apparatus for Measurement of Emissivity for Radiative Cooling of Hypersonic Aircraft with Data for Inconel and Inconel X

The importance of radiation as a means of cooling high-supersonic- and hypersonic-speed aircraft is discussed to show the need for measurements of the total hemispherical emissivity of surfaces. The theory underlying the measurement of the total hemispherical emissivity of surfaces is presented, readily duplicable apparatus for performing the measurements is described, and measurements for stably oxidized Inconel and Inconel X are given for the temperature range from 600 F to 2,000 F.

MATERIALS, PROPERTIES - THERMAL↗
NASA NTRS1950

Preliminary analysis of problem of determining experimental performance of air-cooled turbine II : methods for determining cooling-air-flow characteristics

In the determination of the performance of an air-cooled turbine, the cooling-air-flow characteristics between the root and the tip of the blades must be evaluated. The methods, which must be verified and the unknown functions evaluated, that are expected to permit the determination of pressure, temperature, and velocity through the blade cooling-air passages from specific investigation are presented.

FLOW, COMPRESSIBLE↗