Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zirconium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Fundamental Studies of Tritium Formation and Diffusivity in Pure and Defective Zircaloy-4 Getters

Zirconium (Zr) and its alloys are used as fuel cladding in nuclear reactors. These materials have their low absorption cross-section for thermal neutrons and have good mechanical and thermal properties. In addition, they are used as tritium getters in tritium-producing burnable absorber rods (TPBARs), in the form of nickel-plated Zircaloy-4 tubes. To produce 3 H, the breading blankets such as lithium aluminate are irradiated in pressurized water. 3 H produced in this process is captured by the getter and 3 H reacts chemically with Zr to form metal hydride (ZrTx). The precipitation of metal hydride results in not only the volume increase and hydrogen embrittlement of zircaloy but also changes in getter’s chemical properties. This degrades the getter’s performance. Therefore, understanding the behavior of 3 H (such as diffusion and solubility) in zircaloy is important to understand getter performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Development of a Castable High Strength Secondary Aluminum Alloy from Recycled Wrought Aluminum Scrap

A new process for recycling scrap AA7075 aerospace alloys directly into a high strength castable secondary alloy is demonstrated. The process involves enhancing the castability of the utilized primary wrought aluminum scrap feedstock by scrap alloy chemistry optimization and zirconium additions in order to mitigate the inherent hot tearing tendency of 7075 alloys. By utilizing the new process, the hot tearing index of scrap AA7075 was reduced from 26 to 4. Defect-free castings were obtained in pilot-scale castings trials. The developed secondary 7075 alloy also satisfied preset target mechanical properties with strength levels exceeding 250 MPa and elongation levels higher than 3%. The validity of the new approach and its readiness for transition to commercial practice was demonstrated by casting cylinder heads directly from the modified 7075 scrap.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fuel Performance Analysis of Chromium-Coated Cladding under Burst Conditions

To reduce the oxidation of zirconium-based alloy cladding at high temperatures, accident tolerant fuel systems have been proposed. Of the concepts identified, chromium-coated cladding has been shown to slow oxidation without greatly impacting the fuel system geometry or neutronic performance. To determine how coated-cladding tubes will perform under high-temperature accident conditions, pressurized-tube burst tests have been performed using the Severe Accident Test Station at Oak Ridge National Laboratory. To begin modeling these tubes to better understand how the coating will impact cladding behavior, these burst tests were simulated with the BISON fuel performance code. Cladding tube surface temperatures for the burst test were developed by fitting thermocouple data into axial and azimuthal profiles, while pressure data were compared until cladding failure. The temperatures at failure and the pressure evolution show relatively good agreement between the simulation and experiment results. This is the first step of a larger effort to simulate the cladding deformation process under high-temperature transient conditions and assess the cladding margin to failure more accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Casting and Characterization of U-50Zr

Uranium alloyed with 50 wt% zirconium (U-50Zr) is a proposed light water reactor (LWR) nuclear fuel by Lightbridge Corporation (LTBR). The proposed method for making the U-50Zr alloy is to arc-melt master alloys and then remelt in a vacuum induction melter (VIM) to consolidate the material and cast into an intermediate shape. After casting, the material will eventually need to be formed into a desired fuel shape. The work discussed in this report resulted from a joint effort between Ltbr and Pacific Northwest National Laboratory (PNN) to investigate a 500g – 1kg scale casting process to produce the U-50Zr alloy in the desired δ-UZr 2 phase and characterize the impurities and microstructure that result from the casting process. Master alloys were fabricated in an arc melter, then five castings were carried out in a VIM with multiple inert coating and crucible materials to find an appropriate combination. Both ZrO 2 and graphite crucibles were used and different combinations of Y 2 O 3 , CaZrO 3 , and TiC to identify which would contain the molten metal with the least reaction. On each casting, the C, O, N, H impurities were analyzed as well as the phase by x-ray diffraction and microstructure. Of the five castings, two resulted in majority of δ-UZr 2 phase-pure material and had impurity levels within acceptable ranges. The two most successful castings utilized a graphite crucible with a TiC undercoating and a Y 2 O 3 overcoat. The O and N levels were below 1000 ppm and the C content was variable but did not result in measurable carbide formation. The highest success casting resulted in an average of 282 ppm C, 567 ppm O, 217 ppm N and 79 ppm H. This casting's crucible and inert coating material was repeated with slightly different casting parameters and resulted in higher C numbers but similar phase identification. The differences between each casting are discussed and recommendations are made for future experiments to better decide on a casting process to go forward with.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Pressure Composition Temperature Curves of Hydride Moderators

Microreactors are compact and mobile reactors which operate at low power and high temperatures. These reactors generate heat which is then converted to electricity for use in a variety of special purpose applications. Microreactors are of interest due to their light weight, compact size and the ability to meet the needs for high energy in difficult or remote areas. Metal hydrides have been studied for nuclear and aviation applications. The emergence of microreactors the interest in metal hydrides is significant due to their ability to moderate neutrons in a light weight and solid form. In case of an off normal event, more accurate data is needed for the absorption/desorption rates of the hydrides due to the high uncertainties on hydrogen redistribution in the moderator. The literature shows considerable discrepancies in the PCT curves for yttrium and zirconium. The uncertainty is much more notable at higher stoichiometries of the hydride phase at high temperature. To understand the in-pile performance, a detailed understating of the impurities and microstructure is needed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Development of Hydrogen Permeation Barrier and Matrix Interaction Protection Coatings for TZM Enclosure of Hydride Moderators (Microreactor Program M3 Report)

It is important to develop a high-performance enclosure solution for hydride-based microreactor moderation components to effectively suppress hydride thermal decomposition and prevent hydrogen loss in harsh in-reactor environments. Currently, the DOE-NE Microreactor Program (MR program) is investigating the titanium-zirconium-molybdenum (TZM) canned yttrium hydride (YH 2-x ) solution, which provides acceptable hydrogen retainment performance up to ~700 °C. However, improvements in the enclosure are necessary for increasing long-term operation temperature beyond 700 °C and enhancing short-term survivability at even higher temperatures during power transients. One potential solution is the addition of a dedicated hydrogen permeation barrier, which can potentially improve the enclosure's performance. Furthermore, the hydride moderator components will be inserted into the microreactor matrix, which may consist of materials that are not chemically inert against TZM. Therefore, the TZM might need to be protected from the external environment through the application of another surface protection coating. To address these critical issues, two types of barrier coatings optimized for TZM-based moderator enclosure has been developed. A multilayer coating approach has been used to identify TZM-compatible barrier materials. Behavior of these coating designs against H 2 permeation and long-term high-temperature graphite matrix interactions has been examined in detail. Additionally, the developed coatings' behavior when exposed to both high-temperature thermal cycling and heavy-ion irradiation has also been investigated. Overall, the development of these barrier coatings is essential for achieving maturity for the metal hydride moderator technology. The results in this report will provide crucial insights into the behavior of the developed coatings and their potential for improving the long-term performance of TZM-based moderator enclosures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Degradation and Failure Phenomena of Accident Tolerant Fuel Concepts: FeCrAl Alloy Cladding

The U.S. Nuclear Regulatory Commission (NRC) is anticipating licensing applications and commercial use of accident tolerant fuel (ATF) in United States commercial nuclear power reactors. Pacific Northwest National Laboratory is providing technical assistance to the NRC related to the newly proposed nuclear fuel and cladding designs. This report focuses specifically on the iron-chromium-aluminum (FeCrAl) alloys being investigated to replace zirconium-based alloys for fuel cladding and provides current state-of-the-industry information on material properties and fuel performance considerations under reactor operating conditions and design basis accident conditions. Currently, Global Nuclear Fuels (GNF) is the only U.S.-based fuel vendor considering FeCrAl cladding as a near-term ATF design. GNF has tested several different FeCrAl alloys including Kanthal APMT, C26M, and MA956; fueled C26M rods and unfueled Kanthal APMT, C26M, and MA956 rods have been inserted in lead test assemblies at Plants Hatch and Clinton. This report will focus on those three alloys specifically, with broader information given regarding in-reactor and ex-reactor testing of FeCrAl alloys. To support the NRC’s readiness efforts, this report will identify and discuss degradation and failure modes of FeCrAl cladding concepts, including fuel performance characteristics that may not be addressed within existing regulatory documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

ORNL Analysis of Leach-Burn-Leach Round-Robin Test Samples

An international round-robin test to examine the consistency in leach-burn-leach (LBL) analysis of tristructural-isotropic- (TRISO-) coated particle fuel was conducted by three research organizations from the Generation IV International Forum member countries of the People’s Republic of China, the Republic of Korea, and the United States of America. Two sets of round-robin test samples were exchanged for analysis. One set of samples consisted of a series of nonuranium-bearing, TRISO-coated zirconium dioxide particles seeded with up to four depleted uranium-bearing, TRISO-coated uranium dioxide (UO 2 ) particles, which had intentionally damaged coating layers to simulate either particles with either exposed-kernel defects (i.e., particles with a cracked TRISO coating that should be detected during preburn leaching) or particles with silicon carbide (SiC) defects (i.e., particles with an intact pyrocarbon coating and a hole in the SiC layer that should be detected during postburn leaching). These simulated samples also contained added powder with known quantities of impurities from a coal standard. The other sample set consisted of representative sublots of UO 2 -TRISO particles fabricated in a production-scale coater, except they all contained depleted uranium instead of enriched uranium. In this report, the methodology used at Oak Ridge National Laboratory to conduct LBL analysis of the round-robin samples is presented, and the general results are summarized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Studies of Reactive Amorphous Compounds and Surfaces: Their Pathways to Crystallinity and Surface Functionality

This project was originally headed by Dr. Abraham Clearfield (Texas A&M University, ret.) and focused on developing structural models of zirconium phosphate (ZrP) based materials at different stages of crystalline order using PDF techniques developed by co-PI Dr. Simon Billinge (Columbia University). When Dr. Clearfield retired, the project was taken over by Dr. Hong-Cai Zhou (Texas A&M University). The project proposed looking at defective metal-organic frameworks (MOFs) supported on the surface of the ZrP materials. During the project, the personnel conducted studies of the dispersion of different phosphate ligands in mixed organic phosphonates, and how they could be utilized to incorporate different metals within the ZrP interlayer spacing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

AFC FY 2023 HFIR Irradiation Test Matrix – Supported by the Design of a Ring Specimen Irradiation Vehicle

The development and deployment of accident-tolerant cladding materials in light water nuclear reactors requires the collection of neutron-irradiated properties of these materials with specific consideration to the material properties orientation (i.e., tube geometry). To that end, a test plan to irradiate several cladding tube and ring specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) was proposed, along with the development of a new capsule design that features ring specimens with a preexisting gauge section. This ring specimen geometry removes the need to machine a gauge section on the irradiated specimen and thus allows for direct application of a ring-pull test post-irradiation. The test matrix includes uncoated and chromium-coated Zircaloy-4 and advanced zirconium alloy cladding specimens, pre-characterized at ORNL. Plans are to irradiate the specimens at about 4 and 10 dpa—corresponding to two and five cycles at the HFIR centerline—with a target specimen gauge section temperature of 330°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

First-Principles Studies of Tritium Species Dissociability & Diffusivity Across the Interface of Nickel-Plated Zircaloy-4

Zirconium (Zr) and its alloys (Zircaloy-4) are widely used in nuclear reactors due to their low neutron adsorption cross-section and excellent corrosion resistance. In tritium-producing burnable absorber rods (TPBARs), the metal getter tube located between the cladding and the γ-LiAlO 2 pellets is composed of nickel (Ni)-plated Zircaloy-4, which is used to capture tritium ( 3 H) species (mainly 3 H 2 and 3 H 2 O) generated from γ-LiAlO 2 pellets during irradiation. The 3 H-related products transfer to the surface of metal Ni upon adsorption and dissociation to form new 3 H species and diffuse into the Zircaloy-4 getters to form metal hydrides (Zr 3 H x ). Therefore, exploring 3 H species ( 3 H 2 , 3 H 2 O) dissociation on the surface of Ni and diffusion across the interface of Ni-plated Zircaloy-4 getters can provide a better understanding of 3H species formation and transport from pellets into the getters.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Irradiation creep model for α-Fe: Dislocation climb in the presence of stress fields (Final Report)

Irradiation creep is known to be an important process for structural materials in nuclear environments, potentially leading to creep failure at temperatures where thermal creep is generally negligible. While there is a great deal of data for irradiation creep in steels and zirconium alloys in light water reactor conditions, much less is known for first wall materials under fusion energy conditions. Lacking suitable fusion neutron sources for detailed experimentation, modeling, and simulation can help bridge the dose-rate and spectral-effects gap and produce quantifiable expectations for creep deformation of first wall materials under standard fusion conditions. In this work, we present a comprehensive model for irradiation creep created from merging a crystal plasticity representation of the dislocation microstructure and a defect evolution simulator that accounts for the entire cluster dimensionality space. Both approaches are linked by way of a climb velocity that captures dislocation-biased defect absorption and a dislocation strengthening term that reflects the accumulation of defect clusters in the system. We carry out our study in Fe under first wall fusion reactor conditions, characterized by a fusion neutron spectrum at temperatures between 300 and 800°K.

36 MATERIALS SCIENCE↗
DOE OSTI2024

NASA: Structure and Thermophysical Properties of Delta and Epsilon Zry4H x

Small-modular and micro-reactors are part of an emerging nuclear technology aimed to provide power to decentralized grids in civilian, industrial, and defense energy sectors. Resurgence in microreactor research is partly driven by demands for a mobile, safe, and compact energy platform for remote and strategic locations. The defining characteristics of the microreactor include its high-power density on a small footprint, its highly transportable design, and the use of high-assay low-enriched uranium (HALEU) fuel. Solid-state metal hydride neutron moderator components are considered for microreactor designs where the moderator functions to thermalize neutrons into lower energies for the fuel to achieve high fission rates. Zirconium hydride (ZrH x where x denotes the atomic hydrogen-to-metal ratio) is a leading moderator candidate material due to the combination of its low neutron absorption cross section, irradiation resistance, high hydrogen atomic density (upwards of 7.5 x 10 22 H atoms/cm 3 at low temperatures), and high hydrogen desorption (dissociation) temperature around 600 °C (873 K) compared to other metal hydrides. Its high-temperature stability enables operation of fuel temperatures into several hundred degrees Celsius for overall increased efficiency.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

New dynamic diamond anvil cell for time-resolved radial x-ray diffraction

The dynamic diamond anvil cell (dDAC) is a recently developed experimental platform that has shown promise for studying the behavior of materials at strain rates ranging from intermediate to quasi-static and shock compression regimes. Combining dDAC with time-resolved x-ray diffraction (XRD) in the radial geometry (i.e., with incident x-rays perpendicular to the axis of compression) enables the study of material properties such as strength, texture evolution, and deformation mechanisms. This work describes a radial XRD dDAC setup at beamline P02.2 (Extreme Conditions Beamline) at DESY’s PETRA III synchrotron. Time-resolved radial XRD data are collected for titanium, zirconium, and zircon samples, demonstrating the ability to study the strength and texture of materials at compression rates above 300 GPa/s. In addition, the simultaneous optical imaging of the DAC sample chamber is demonstrated. The ability to conduct simultaneous radial XRD and optical imaging provides the opportunity to characterize plastic strain and deviatoric strain rates in the DAC at intermediate rates, exploring the strength and deformation mechanisms of materials in this regime.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Bench-Scale Electrolytic Dissolution of Quarter-Scale FCA Cans

In 2016, the Savannah River National Laboratory (SRNL) led, in support of and under sponsorship of the Department of Energy’s National Nuclear Security Administration (DOE/NNSA) Office of Material Management and Minimization (M3), the removal and transfer of the plutonium based Fast Critical Assembly (FCA) fuel from the Japan Atomic Energy Agency (JAEA) Tokai facility to the Savannah River Site (SRS). The team also included JAEA, multiple organizations in Savannah River Nuclear Solutions (SRNS), International Nuclear Services, and many other entities. The FCA fuel removal project completion was a key deliverable for M3 to the 2016 Nuclear Security Summit and constituted the largest inventory of weapons-usable plutonium removed under the nonproliferation program. The FCA materials consist of thousands of stainless steel (SS) clad plates and hundreds of SS clad rods. The FCA fuel elements were packaged in a carrier can and stored at SRS pending disposition of the fuel. Following an assessment of candidate disposition options, SRNS identified electrolytic dissolution (ED) as the most promising disposition option for the FCA plates and their preferred option was endorsed by DOE. This option entails electrochemically dissolving the entire FCA carrier can with fuel elements and was based on bench-scale laboratory testing and historical work on processing SS-clad and zirconium-clad uranium-based fuel in the H-Canyon electrolytic dissolver (last operated in 1980). The FCA plate consists of a plutonium-aluminum metal alloy core hermitically sealed in SS cladding.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Irradiation of Mo-100 Targets and Testing Fe(ll)CI 2 Precipitation for Tc-99 Removal

The production of molybdenum-99 (Mo-99) is a critical step in the generation of technetium-99m (Tc-99m), a radioisotope widely used in medical imaging. NorthStar Medical Radioisotopes, LLC is planning to produce the important medical radioisotope Mo-99 through a photonuclear reaction on molybdenum-100 (Mo-100). Accelerator production of Mo-99 using enriched Mo-100 targets yields undesirable isotopes, such as niobium-95 (Nb-95) and zirconium-95 (Zr-95). Previous studies reported that Nb and Zr isotopes can be effectively removed from Mo-99 products through coprecipitation with Fe(III). To enable the potential utilization of the first milking of Tc-99m from a Mo-99/Tc-99m generator, it is desirable to remove long-lived Tc-99. This can be accomplished by substituting Fe(III) with Fe(II) during the precipitation step, without affecting the removal of Zr and Nb isotopes. Previous experiments demonstrated up to 99+% removal of Tc using this method. It was also observed that the presence of hydrogen peroxide significantly impacts Tc removal. This was evident in the processing of enriched Mo-100 targets, where only 25% of Tc was removed. To further investigate this, another irradiation of enriched Mo-100 disks was conducted, followed by Tc-99 removal using Fe(II). Prior to irradiation, experimental conditions for Tc removal were optimized through several test runs using Mo-100 disks spiked with Tc-99. The results of these tests are discussed in this report.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Analysis of the Surface Morphology and Chemical Composition of Zr-Nb3Sn Alloys with Zr Different Concentrations

The inclusion of zirconium (Zr) in niobium-tin (Nb3Sn) significantly enhances the performance of Nb3Sn radiofrequency cavities in high magnetic fields. This research project is dedicated to characterizing the surface properties and chemical composition of Zr-doped Nb3Sn. Two different concentrations of Zr were used for doping: approximately 0.5% and 24%. Various spectroscopy techniques were employed to analyze how the surface morphology and chemical composition of Nb3Sn change with increasing Zr content. The findings of this study indicate that the grain size decreases as the Zr concentration increases. In samples with 24% Zr, nanometer-sized particles, likely oxides, were observed. X-ray photoelectron spectroscopy (XPS) data revealed that the thickness of niobium oxides (NbOx) decreases with increasing Zr, while the thickness of tin oxides (SnOx) increases. Additionally, grain size distribution analysis showed that the average grain size is around 5300 nm , with a grain area density of about 165 grains/μm .

Sue, Micah↗