Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal spray”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

854 records · Page 48

Recent Ground Hold and Rapid Depressurization Testing of Multilayer Systems

In the development of flight insulation systems for large cryogenic orbital storage (spray on foam and multilayer insulation), testing need include all environments that are experienced during flight. While large efforts have been expended on studying, bounding, and modeling the orbital performance of the insulation systems, little effort has been expended on the ground hold and ascent phases of a mission. Historical cryogenic in-space systems that have flown have been able to ignore these phases of flight due to the insulation system being within a vacuum jacket. In the development phase of the Nuclear Mars Vehicle and the Shuttle Nuclear Vehicle, several insulation systems were evaluated for the full mission cycle. Since that time there had been minimal work on these phases of flight until the Constellation program began investigating cryogenic service modules and long duration upper stages. With the inception of the Cryogenic Propellant Storage and Transfer Technology Demonstration Mission, a specific need was seen for the data and as such, several tests were added to the Cryogenic Boil-off Reduction System liquid hydrogen test matrix to provide more data on a insulation system. Testing was attempted with both gaseous nitrogen (GN2) and gaseous helium (GHe) backfills. The initial tests with nitrogen backfill were not successfully completed due to nitrogen liquefaction and solidification preventing the rapid pumpdown of the vacuum chamber. Subsequent helium backfill tests were successful and showed minimal degradation. The results are compared to the historical data.

Space Environment Simulation↗

Analysis of the Honeywell Uncertified Research Engine (HURE) with Ice Crystal Cloud Ingestion at Simulated Altitudes: Public Version

The Honeywell Uncertified Research Engine (HURE), a research version of a turbofan engine that never entered production, was tested in the NASA Propulsion System Laboratory (PSL), an altitude test facility at the NASA Glenn Research Center. The PSL is a facility that is equipped with water spray bars capable of producing an ice cloud consisting of ice particles, having a controlled particle diameter and concentration in the air flow. In preparation for testing of the HURE, numerical analysis of flow and ice particle thermodynamics was performed on the compression system of the turbofan engine to predict operating conditions that could potentially result in a risk of ice accretion due to ice crystal ingestion. The results of those analyses formed the basis of the test matrix. The goal of the test matrix was to have ice accrete in two regions of the compression system: region one, which consists of the fan-stator through the inlet guide vane (IGV), and region two which is the first stator within the high pressure compressor. The predictive analyses were performed with the mean line compressor flow modeling code (COMDES-MELT) which includes an ice particle model. Together these comprise a one-dimensional icing tool. The HURE engine was tested in PSL with the ice cloud over the range of operating conditions of altitude, ambient temperature, simulated flight Mach number, and fan speed with guidance from the analytical predictions. The engine was fitted with video cameras at strategic locations within the engine compression system flow path where ice was predicted to accrete, in order to visually confirm ice accretion when it occurred. In addition, traditional compressor instrumentation such as total pressure and temperature probes, static pressure taps, and metal temperature thermocouples were installed in targeted areas where the risk of ice accretion was expected. The current research focuses on the analysis of the data that was obtained after testing the HURE engine in PSL with ice crystal ingestion. The computational method was enhanced by computing key parameters through the fan-stator at multiple spanwise locations, in order to increase the fidelity with the current mean-line method. In addition, other sources of heat (non-adiabatic walls) were suspected to be the cause of accretion near the splitter-lip and shroud. Since there were no thermocouples near the splitter, a simple order of magnitude heat transfer model was implemented to estimate the wall temperature. Future analyses will require a higher fidelity thermal analysis of the compression system metal walls to accurately calculate the total heat flux to the ice particle. For many data points analyzed, there were differences between the thermodynamic system model and the measured test data that may partially be responsible for uncertainties with the results of the current analyses.

Turbomachinery↗

Recent Advancements in the PATO Material Response Code

Introduction: Predicting the complicated multiphysics phenomena during atmospheric entry requires high-fidelity modeling tools to refine estimates of mission risks during entry. To this end, new capabilities are being added to the Porous-material Analysis Toolbox based on OpenFOAM (PATO) [1,2,3]. PATO is an open-source software for Computational Material Response (CMR) of reactive porous materials submitted to high-temperature environments. The objective of this work is to highlight current efforts to add to and improve upon the modeling capabilities of PATO. These include efforts to loosely couple PATO with other discipline specialized codes including hypersonic Computational Fluid Dynamics (CFD), to assess the interaction effects between pyrolysis gas blowing and the boundary layer, and Computational Solid Mechanics (CSM), to address modeling of mechanical erosion. Other refinements include surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation, and a unified multiphase solver for a mixed porous-material and plain-fluid domain. Coupling CMR with CFD (CMR/CFD): A loose coupling between PATO and the Data Parallel Line Relaxation (DPLR) [4] CFD code has been achieved by making use of a blowing boundary condition at the heatshield surface available in DPLR. Starting with heat flux estimates with no pyrolysis gas blowing at the surface, blowing gases are computed by the CMR and passed to the CFD such that aerothermal properties of the environment can be recomputed for a new CMR computation. This leads to an iterative process which is supplemented with an estimate of the radiative heat flux using the Nonequilibrium air radiation (NEQAIR) [5] program. The entire iterative process is illustrated in Figure 1. This coupling strategy has been utilized in computing the MSL material response. The goal is to compare the coupled CMR/CFD results with material response results obtained using traditional blowing corrections. Coupling CMS with CMR: A mechanical erosion model is currently being implemented in PATO to account for the additional mass removal induced by high shear conditions. The modeling process at each timestep consists of updating the mechanical properties as a function of temperature and computing the stress tensor and displacement fields of the material. Then, a failure criteria model determines the regions in which the stress exceeds the ultimate strength values resulting in mesh movement to account for mass removal. This model allows the material response simulation to compute the recession due to both oxidation and shear-induced erosion. The model is demonstrated by computing material response of sphere-cone arc jet samples. Surface Modeling Capabilities: NuSil, a silicone-based coating, was sprayed onto the MSL and Mars 2020 heatshields to mitigate shedding of phenolic dust. To better understand the effects of the NuSil coating on the material response, a novel model has been implemented in PATO. In this model, the equilibrium of the charred NuSil surface is modeled as pure silica, and a constant offset, inspired by the classical spallation model, is added to the the char blowing rate and wall enthalpy to reproduce HyMETS experimental results. The model has also been used to estimate the 3D material response of the MSL heatshield [6]. Unified Solver: In addition to the iterative loose coupling approach mentioned above, a multiphase unified solver is being developed to couple the environment (plain-fluid phase) and the porous-material phase. The solver is based on the volume averaged conservation of mass, momentum, and energy for the macroscale with closure models which include microscale effects through effective physicochemical properties. The unified solver has been used to compute flow through a porous plug and solve the Beavers and Joseph problem [7]. Since the strong coupling between phases is inherent to this solver, modeling assumptions present in other coupling methods of material response are mitigated. This strategy also makes it feasible to capture the competition between surface and volume ablation in the same computational domain, which is usually not possible with other coupling approaches.

Thermal Protection Systems↗

Recent Advancements in the PATO Material Response Code

Introduction: Predicting the complicated multiphysics phenomena during atmospheric entry requires high-fidelity modeling tools to refine estimates of mission risks during entry. To this end, new capabilities are being added to the Porous-material Analysis Toolbox based on OpenFOAM (PATO). PATO is an open-source software for Computational Material Response (CMR) of reactive porous materials submitted to high-temperature environments. The objective of this work is to highlight current efforts to add to and improve upon the modeling capabilities of PATO. These include efforts to loosely couple PATO with other discipline specialized codes including hypersonic Computational Fluid Dynamics (CFD), to assess the interaction effects between pyrolysis gas blowing and the boundary layer, and Computational Solid Mechanics (CSM), to address modeling of mechanical erosion. Other refinements include surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation, and a unified multiphase solver for a mixed porous-material and plain-fluid domain. Coupling CMR with CFD (CMR/CFD): A loose coupling between PATO and the Data Parallel Line Relaxation (DPLR) CFD code has been achieved by making use of a blowing boundary condition at the heatshield surface available in DPLR. Starting with heat flux estimates with no pyrolysis gas blowing at the surface, blowing gases are computed by the CMR and passed to the CFD such that aerothermal properties of the environment can be recomputed for a new CMR computation. This leads to an iterative process which is supplemented with an estimate of the radiative heat flux using the Nonequilibrium air radiation (NEQAIR) program. The entire iterative process is illustrated in Figure 1. This coupling strategy has been utilized in computing the MSL material response. The goal is to compare the coupled CMR/CFD results with material response results obtained using traditional blowing corrections. Coupling CMS with CMR: A mechanical erosion model is currently being implemented in PATO to account for the additional mass removal induced by high shear conditions. The modeling process at each timestep consists of updating the mechanical properties as a function of temperature and computing the stress tensor and displacement fields of the material. Then, a failure criteria model determines the regions in which the stress exceeds the ultimate strength values resulting in mesh movement to account for mass removal. This model allows the material response simulation to compute the recession due to both oxidation and shear-induced erosion. The model is demonstrated by computing material response of sphere-cone arc jet samples. Surface Modeling Capabilities: NuSil, a silicone-based coating, was sprayed onto the MSL and Mars 2020 heatshields to mitigate shedding of phenolic dust. To better understand the effects of the NuSil coating on the material response, a novel model has been implemented in PATO. In this model, the equilibrium of the charred NuSil surface is modeled as pure silica, and a constant offset, inspired by the classical spallation model, is added to the the char blowing rate and wall enthalpy to reproduce HyMETS experimental results. The model has also been used to estimate the 3D material response of the MSL heatshield. Unified Solver: In addition to the iterative loose coupling approach mentioned above, a multiphase unified solver is being developed to couple the environment (plain-fluid phase) and the porous-material phase. The solver is based on the volume averaged conservation of mass, momentum, and energy for the macroscale with closure models which include microscale effects through effective physicochemical properties. The unified solver has been used to compute flow through a porous plug and solve the Beavers and Joseph problem. Since the strong coupling between phases is inherent to this solver, modeling assumptions present in other coupling methods of material response are mitigated. This strategy also makes it feasible to capture the competition between surface and volume ablation in the same computational domain, which is usually not possible with other coupling approaches.

Material Response↗

Sulfur and Moisture Effects on Alumina Scale and TBC Spallation

It has been well established that a few ppmw sulfur impurity may segregate to the interface of thermally grown alumina scales and the underlying substrate, resulting in bond degradation and premature spallation. This has been shown for NiAl and NiCrAl-based alloys, bare single crystal superalloys, or coated superalloys. The role of reactive elements (especially Y) has been to getter the sulfur in the bulk and preclude interfacial segregation. Pt additions are also very beneficial, however a similar thermodynamic explanation does not apply. The purpose of the present discussion is to highlight some observations of these effects on Rene'142, Rene'N5, PWA1480, and PWA1484. For PWA1480, we have mapped cyclic oxidation and spallation in terms of potential sulfur interfacial layers and found that a cumulative amount of about one monolayer is sufficient to degrade long term adhesion. Depending on substrate thickness, optimum performance occurs if sulfur is reduced below about 0.2-0.5 ppmw. This is accomplished in the laboratory by hydrogen annealing or commercially by melt-fluxing. Excellent 1150 C cyclic oxidation is thus demonstrated for desulfurized Rene'142, Rene'N5, and PWA1484. Alternatively, a series of N5 alloys provided by GE-AE have shown that as little as 15 ppmw of Y dopant was effective in providing remarkable scale adhesion. In support of a Y-S gettering mechanism, hydrogen annealing was unable to desulfurize these alloys from their initial level of 5 ppmw S. This impurity and critical doping level corresponds closely to YS or Y2S3 stoichiometry. In many cases, Y-doped alloys or alloys with marginal sulfur levels exhibit an oxidative sensitivity to the ambient humidity called Moisture-Induced Delayed Spallation (MIDS). After substantial scale growth, coupled with damage from repeated cycling, cold samples may spall after a period of time, breathing on them, or immersing them in water. While stress corrosion arguments may apply, we propose that the underlying cause is related to a hydrogen embrittlement reaction: Al alloy + 3 H2O = Al(OH)3 + 3H(+) + 3e(-). This mechanism is derived from an analogous moisture-induced hydrogen embrittlement mechanism originally shown for Ni3Al and FeAl intermetallics. Consequently, a cathodic hydrogen charging technique was used to demonstrate that electrolytic de-scaling occurs for these otherwise adherent alumina scales formed on Y-doped Rene'N5, in support of hydrogen effects. Finally, some TBC observations are discussed in light of all of the above. Plasma sprayed 8YSZ coatings, produced on PWA1484 without a bond coat, were found to survive more than 1000 1-hr cycles at 1100 C when desulfurized to below 0.1 ppmw. At higher sulfur (1.2 ppmw) levels, moisture sensitivity and delayed TBC failure, referred to as Desk Top Spallation, occurred at just 200 hr. Despite a large degree of scatter, a factor of 5 in life improvement is indicated for desulfurized samples in cyclic furnace tests, confirming the beneficial effect of low sulfur alloys on model TBC systems. (DTS and moisture effects are also observed on commercially applied PVD 7YSZ coatings on Rene'N5+Y with Pt-aluminide bond coats). These types of catastrophic failure were subverted on the model system by segmenting the substrate into a network of 0.010 high ribs, spaced in. apart, prior to plasma spraying. No failures occurred after 1000 cycles at 1150 C or after 2000 cycles at 1100 C, even after water immersion. The benefit is described in terms of elasticity models and a critical buckling stress.

Smialek, James L.↗

Tracking Radioactive Isotopes in HVAC and Application for Hot Cell Analyses - 20155

In recent years, the surge in the number of isotope production facilities under design has increased the need to analyze isotope migration in facility Heating, Ventilation, and Air Conditioning (HVAC) during normal operations and accident scenarios. These facilities are used to produce isotopes for medical, security, and industrial applications and as such are subject to license and regulatory requirements 10CFR20, 10CFR30, 10CFR50, and 10CFR70. GOTHIC, a general-purpose thermal-hydraulics software package, includes the ability to model isotopic tracers, radioactive decay and isotope migration as well as HEPA and charcoal filters for isotope retention. A GOTHIC model was developed by Zachry Nuclear Engineering (ZNE) to examine the effect of negative room pressure, HEPA filtration, and HVAC fluctuations on radiation areas, hot cells and gloveboxes. Radioactive tracers were used to simulate the concentration of spills within contaminated areas, track the migration of isotopes of interest, and determine the isotopic retention and buildup on facility HEPA filters. A variety of isotopes with concern to dose (e.g., Kr-85, Sr-90, I-131, etc.), including their decay and progeny, are included in the analysis. Negative pressures are maintained in the regions of interest by a representative central HVAC system equipped with a volumetric fan that exhausts to the environment after a series of isolation valves and HEPA filters. GOTHIC is an industry trusted tool for providing engineering solutions for a variety of applications, including fission product tracking, aerosol and particulate transport and ventilation assessments. The software provides an integrated analysis environment that includes a graphical user interface (GUI) for constructing analysis models, a numerical solver that includes parallel processing capabilities and a post-processor for evaluating simulation results. It solves the conservation equations for mass, momentum and energy for multicomponent, multi-phase flow in lumped parameter and multi-dimensional geometries (1, 2, or full 3D), including the effects of turbulence, diffusion and buoyancy. It has been developed and maintained under a Quality Assurance program in compliance with the requirements of 10CFR50 Appendix B and applicable portions of ASME NQA-1 since 1995. GOTHIC has been used for assessing both forced and natural convection conditions for a wide range of applications, including: - Tracking concentration of hazardous gases and chemicals for habitability and safety assessments - Determining ventilation and filtration requirements and optimizing location and arrangement of these systems - Room heat-up, including diverse and Flexible coping strategies for Extended Loss of AC Power (FLEX/ELAP) - Equipment Qualification (EQ) A distinctive feature of GOTHIC is the ability to track many different fields/substances in a simulation, including user defined tracer elements, in the liquid, vapor and droplet fields as well as surfaces and filters. This capability allows GOTHIC to model fission product transport and release or the removal of particulates or harmful toxins from exhaust gases using a spray scrubber or other types of filtration systems. GOTHIC also includes models for engineered equipment, such as fans, filters, charcoal filters, dryers/demisters, dampers, etc. The aerosols and other filtered material are removed or accumulated in these components. The range of aerosol and radiological applications that GOTHIC has been used for includes: - Source Term: Primary Coolant (Equilibrium) Activity; Non-Water Coolant Source/Leakage. - Conditions for Iodine Re-evolution: Sump/Suppression Pool Conditions and pH; - RWST Conditions and pH. - Isotope Removal Mechanisms: Containment Sprayed and Unsprayed Region Mixing; Charcoal Filter Heating due to Iodine decay. - Radionuclide Transport and Decay: Post-LOCA Release in containment; Transport between connected Compartments and vent systems; Groundwater transport of radionuclides. - Non-Newtonian Fluid modeling for sludge, waste tanks, etc. ADAMS ML071581053 (titled 'Best Practice Guidelines for the use of CFD in Nuclear Reactor Safety Applications') poses guidelines for applying single phase CFD codes in nuclear reactor safety problems and GOTHIC is listed as a 'tool for 3D flows' and 'dispersal and deposition of radionuclides.' The Nuclear Quality Assurance (NQA) pedigree of GOTHIC is an important aspect for applications in the nuclear industry. The fundamental tracer models (convective transport, molecular and turbulent diffusion, removal mechanisms, etc.) have been verified using analytical solutions and validated against applicable separate effects tests. Also, GOTHIC has been benchmarked to many integrated effects tests, including Phebus FP (Fission Product). GOTHIC gives good agreement for the buildup and decay of fission products in Phebus Test 3. The model developed by ZNE demonstrates GOTHIC's applicability and acceptability for use in analyzing the migration and retention of radioactive isotopes and their progeny in normal operation and accident scenario analyses for isotope production facilities, hot cells, and gloveboxes. The tracer activities calculated by GOTHIC can then be used in downstream radiation transport and shielding codes like RADTRAD-NAI{sup C}, MCNP{sup R}, and MicroShield{sup R} to determine on-site and of-site doses. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

"Dust Devils": Gardening Agents on the Surface of Mars, and Hidden Hazards to Human Exploration?

Dust devils are familiar sites in the and regions of the world: they can produce quite spectacular displays of dust lofting when the vortices scavenge very loose dust from a dry lake bed or from recently disturbed agricultural fields. If one were to arrive at the center of an arid region, take one photograph, or even a series of photographs over a period of several days, then return the images for laboratory analysis, it would be most likely concluded that the region was inactive from an aeolian perspective. No images of general dust movement were obtained, nor were any dust devils "caught on camera" owing to their ephemeral and unpredictable appearance, and the fact that there was deceptively little residue of their actions. If, however, a camera were to take a 360 degree continuous recording over a period of a year, and the film were then to be shown at high speed over a period a several minutes, the impression might be that of a region ravaged by air vorticity and dust movement. Extrapolate this over geological time, and it is possible to visualize dust devils as prime aeolian agents, rather than insignificant vagaries of nature, On Mars, the thin atmosphere permits the surface of the planet to be heated but it does not itself retain heat with the capacity of the earth's atmosphere. This gives rise to greater thermal instability near the surface of Mars as "warm" air pockets diapiritically inject themselves into higher atmospheric layers. Resulting boundary-layer vorticity on Mars might therefore be expected to produce dust devils in abundance, if only seasonally. The spectacular images of dust devils obtained by Pathfinder within its brief functional period on the planet testify to the probability of highly frequent surface vorticity in light of the above reasoning about observational probability. Notably, the Pathfinder devils appeared to be at least a kilometer in height. There are several consequences for the geology of Mars, and for human exploration, if dust devils are to be expected in reasonable abundance. First, from a geological perspective, the vortices will act as "gardening" agents for the top few centimeters of entrainable material. Over time (hundreds of millions, or billions of years being available), they will cover the surface with scouring paths, and the grain sizes that can be lofted by a vortex probably extends over the whole sand to dust range. The depositional paths are, of course, much larger, so that vortex-induced deposition is more widespread than vortex-induced erosion, and will without doubt, affect the whole region in which the dust devils occur (this might explain why rocks at the Viking site seemed oddly capped with dust in a region apparently subject to general aeolian scouring). On Mars, the lift forces in dust devils might be less than on earth owing to the much thinner atmosphere, but this may be counterbalanced by lower gravity and greater vortex velocities. Certainly, when active, other aeolian phenomena on Mars --sand motion and dust storms, seem no less energetic and no less capable of lofting sediments than equivalent terrestrial aeolian phenomena. Every several years, within the current climatic regime, the surface of Mars is subject to light dust fall from global dust storms. Over time, this should develop a very uniform surface layer, with commensurate uniformity in grain size, mineralogy, albedo, color, and general spectroscopic properties. Dust devils will disturb this situation by continually mixing the surface dust with underlying layers, perhaps composed of silt and sand. This size mixing will also involve compositional mixing. After some years, the thin layer of dust that may be difficult to entrain alone, becomes progressively mixed with coarser materials that could reduce the general aeolian threshold of the soil. Certainly the continual disturbance by vorticity will prevent surface stabilization that may bind or indurate grains (caused by slow cementation or ice welding at grain boundaries). If dust devils continually loft dust to kilometer heights, and the dust is sprayed into many cubic kilometers of atmosphere each time, could the devils produce a continual background of atmospheric dust that might be mistaken for the fallout of a distant large-scale dust storm? From a human exploration perspective, dust devils are unlikely to pose any, life- threatening situation for an astronaut unfortunate enough to encounter a momentary swirling cloud of loose soil. However, it is noted that pervasive dust is probably one of the greatest long-term hazards for a human encampment. The fineness and penetration capabilities of the dust, its electrostatic adhesive properties, and its complete ubiquity, render the material a persistent nuisance at best, but at worst, over a period of many months it is possible that space suits, machinery, habitat interiors, air filters, and so forth, could become jeopardized. Owing to dust penetration, the space suits used in the Apollo landings were rendered unusable after a few EVA activities. There will be a definite attempt to situate a human colony on Mars in an area that is far removed from the regions of the planet known for being the centers of major dust storms. At the heart of these storm systems, the dust lofting mechanics are unknown, but they are energetic and perhaps potentially life-threatening for an astronaut. Locating a colony in a region that appears from space to be meteorologically benign may lead to colony placement in a region prone to dust devils, but dust devils are not (or have not been) detectable from orbital observations: the region surveyed for placement will appear like the apparently inactive and area referred to earlier. The region may be spared from highly energetic weather systems, but it may not be necessarily immune from continual dust disturbance. Additional information is contained in the original.

Marshall, J.↗

Adhesion Capabilities of Permanent Foaming Fixatives

DOE-EM have identified an operational requirement for a fixative that can immobilize and/or encapsulate residual contamination in 3D void volumes (pipes, gloveboxes, waste containers, etc.) during D and D activities. Failure to safely and effectively immobilize residual contamination can: Put workers at risk; Contaminate the public and environment; Drive up costs. Commercial-off-the-shelf (COTS) polyurethane (PU) foams is one possible solution and is currently being investigated by Savannah River National Lab (SRNL). Adhesion testing will dictate how well PU foams will adhere and immobilize residual contamination onto a substrate. Results can provide a performance criteria for Section 5 of ASTM E3191: Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination. Initial mechanical testing showed intumescent rigid PU foams were best in class (tensile, compression, TGA/DSC) Application of intumescent rigid PU foam in pipe scenario with 'contamination' showed excellent adhesion capabilities as long as foam had contact with pipe. The foam, however, was not able to penetrate 'contamination' but created pockets where the contamination interacted with the substrate. Pretreatment options of pipe were considered to produce better immobilization capabilities. Pretreatment options included COTS products like baking spray, rubber cement, and soap. Foam was still able to immobilize on a global sense, but not a local sense. Essentially acted as a mechanical plug. A tensile tester (MTS Criterion Series 43) was utilized to evaluate the tensile adhesion strength of 6 COTS PU foams. ASTM D1623: Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics. Procedures: PU foams were cured between two smooth 2'' x 2'' 304 stainless steel coupons with hinges glued on plates for gripping support. Parameters Used: Pull rate of 0.1 in/min. Calculations: Tensile adhesion strength, elongation, and ImageJ analysis of how PU foam is left on substrate. Outcome: The PU foam with the best adhesion capabilities would be downselected for further evaluation to be used as a permanent foaming fixative. The rigid PU foams had the best adhesion capabilities with the R1 foam having a max load of 236 N. One of the I-R2 samples reached almost 450 N and another sample reached 2500 N before slipping. The other intumescent foam, I-F4, had the most coverage on the stainless steel coupon's surface from the ImageJ results (61.43% surface coverage). The intumescent foam, I-R2, will be the foam of choice for future testing due its fire retardant and adhesion capabilities. Future directions: Conduct the following experiment in a pipe scenario with the down-selected PU foam. Procedures: PU foam will be cured between in a 304 stainless steel pipe (ID: 4'', OD: 4.5'', Height: 4''). Parameters Used: Compression testing results will be referenced to determine if foam's adhesion strength would be greater its compression strength as its being compressed. Calculations: Compression strength, shear stress, total time elapsed. Conduct further adhesion testing with the down-selected PU foam (I-R2) to be treated as a permanent foaming fixative (PFF). Determine the minimum contact the PFF should have with the substrate for adequate results. Evaluate if PFF's adhesion capabilities is time dependent (3.1.5 of ASTM E3911). Subject PFF to seismic stressors addressed in Safety Basis of Interim Operation documents (SBIO) to further evaluate adhesion capabilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗