SEARCH · Engineering Papers

Results for “shape analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Analysis and design of a cantilever-mounted resilient-pad gas-lubricated thrust bearing

A thrust bearing consisting of pads mounted on resilient, metallic, cantilever beams is described and analyzed. Compliance and stiffness of the bearing assembly are discussed, and the effects of bearing design parameters on performance are shown. After the general analysis, a design example is presented for a flat sector-shaped gas bearing. A special case where zero axial movement of the runner can be obtained is pointed out.

Etsion, I.↗

NASA NTRS1976

Some aspects on unsteady flow past airfoils and cascades

The unsteady boundary layer due to a gust propagating past an isolated airfoil and on airfoils in cascade was measured with a hot wire anemometer in a low speed gust tunnel. Coherent signals were obtained by a phase lock averaging technique that was implemented in an on-line analysis using a PDP 12 computer. Changes in a boundary layer shape factor, noise level, and pressure gradient were correlated over a complete gust cycle. It is concluded that the character of the boundary layer changes from laminar to turbulent and back to laminar during the course of a gust cycle at certain chordwise positions. These measurements help explain certain anomalies that were observed during a previous study of the pressure fluctuations due to gust loadings on airfoils and cascades.

Satyanarayana, B.↗

NASA NTRS1974

Low speed aerodynamic characteristics of an 0.075-scale F-15 airplane model at high angles of attack and sideslip

An 0.075 scale model representative of the F-15 airplane was tested in the Ames 12 foot pressure wind tunnel at a Mach number of 0.16 to determine static longitudinal and lateral directional characteristics at spin attitudes for Reynolds numbers from 1.48 to 16.4 million per meter (0.45 to 5.0 million per foot). Angles of attack ranged from 0 to +90 deg and from -40 deg to -80 deg while angles of sideslip were varied from -20 deg to +30 deg. Data were obtained for nacelle inlet ramp angles of 0 to 11 deg with the left and right stabilators deflected 0, -25 deg, and differentially 5 deg and -5 deg. The normal pointed nose and two alternate nose shapes were also tested along with several configurations of external stores. Analysis of the results indicate that at higher Reynolds numbers there is a slightly greater tendency to spin inverted than at lower Reynolds numbers. Use of a hemispherical nose in place of the normal pointed nose provided an over correction in simulating yawing moment effects at high Reynolds numbers.

Petroff, D. N.↗

NASA NTRS1978

Aerothermodynamic assessment of corrugated panel thermal protection systems

The results of an analysis of wind-tunnel data for the effect of wave shape on local boundary layer flows and heat transfer are used to assess the feasibility of using corrugated panels on a Single-Stage-To-Orbit (SSTO) vehicle. In the flight assessment, available engineering design procedures are used to compute the inviscid and boundary layer flow for a given flight trajectory. The flight vehicle flow field calculations are then used in conjunction with wind-tunnel corrugated panel heating data correlations to examine the heating penalties associated with using corrugated panels at a number of locations on the vehicle. Severe heating penalties, as a result of the corrugations, were found over large areas of the windward surface. Maximum surface temperature penalties ranged from 100K to 500K and very large structural advantages for the corrugations would be required to override the heating penalties. Computed peak corrugation temperatures were within allowable limits of the equivalent smooth wall material for most leeward and side fuselage locations and corrugated panels will be most likely limited to these locations.

Brandon, H. J.↗

NASA NTRS1979

A model for the noise radiated by turbulent boundary layers and its interaction with laminar layers in supersonic flow

Motivated by the noise-boundary layer transition problem in supersonic flow, the interaction between incoming aerodynamic noise and the laminar boundary layer was studied. The noise field was modeled as a Mach wave radiation field consisting of discrete waves emanating from coherent turbulent entities moving downstream within the supersonic turbulent boundary layer. The individual disturbances are likened to miniature sonic booms and the laminar boundary layer is strafed by the waves as the sources move downstream. The mean, autocorrelation, and power spectral density of the field are expressed in terms of the wave shapes and their average arrival rates. The emphasis in the interaction analysis is on the behavior of the shocklets in the noise field. The shocklets are shown to be focused by the laminar boundary layer in its outer region. Borrowing wave-propagation terminology, this region is termed the caustic region. Using scaling laws from sonic boom work, focus factors at the caustic are estimated to vary from 2 to 6 for incoming shocklet strengths of 1 to .01 percent of the free stream pressure level. The situation regarding experimental evidence of the caustic region is reviewed. It is not clear whether the focusing effectively promotes early transition. Additional observations concerning the interaction problem are presented.

Schopper, M. R.↗

NASA NTRS1979

A model for the noise radiated by turbulent boundary layers and its interaction with laminar layers in supersonic flow

Motivated by the noise-boundary layer transition problem in supersonic flow, the interaction between incoming aerodynamic noise and the laminar boundary layer has been studied. The noise field has been modeled as a Mach wave radiation field consisting of discrete waves emanating from coherent turbulent entities moving downstream within the supersonic turbulent boundary layer. The individual disturbances are likened to miniature sonic booms and the laminar boundary layer is strafed by the waves as the sources move downstream. The mean, autocorrelation, and power spectral density of the field are expressed in terms of the wave shapes and their average arrival rates. The emphasis in the interaction analysis is on the behavior of the shocklets in the noise field. The shocklets are shown to be focused by the laminar boundary layer in its outer region. Borrowing wave-propagation terminology, this region is termed the caustic region. Using scaling laws from sonic boom work, focus factors at the caustic are estimated to vary from 2 to 6 for incoming shocklet strengths of 1 to .01 percent of the free stream pressure level.

Schopper, M. R.↗

NASA NTRS1983

Scatter of elastic waves by a thin flat elliptical inhomogeneity

Elastodynamic fields of a single, flat, elliptical inhomogeneity embedded in an infinite elastic medium subjected to plane time harmonic waves are studied. Scattered displacement amplitudes and stress intensities are obtained in series form for an incident wave in an arbitrary direction. The cases of a penny shaped crack and an elliptical crack are given as examples. The analysis is valid for alpha a up to about two, where alpha is longitudinal wave number and a is a typical geometric parameter.

Fu, L. S.↗

NASA NTRS1983

Time dependence of solid-particle impingement erosion of an aluminum alloy

Erosion studies were conducted on 6061-T6511 aluminum alloy by using jet impingement of glass beads and crushed glass particles to investigate the influence of exposure time on volume loss rate at different pressures. The results indicate a direct relationship between erosion-versus-time curves and pitmorphology (width, depth, and width-depth ratio)-versus-time curves for both glass forms. Extensive erosion data from the literature were analyzed to find the variations of erosion-rate-versus-time curves with respect to the type of device, the size and shape of erodent particles, the abrasive charge, the impact velocity, etc. Analysis of the experimental data, obtained with two forms of glass, resulted in three types of erosion-rate-versus-time curves: (1) curves with incubation, acceleration, and steadystate periods (type 1); (2) curves with incubation, acceleration, decleration, and steady-state periods (type 3); and (3) curves with incubation, acceleration, peak rate, and deceleration periods (type 4). The type 4 curve is a less frequently seen curve and was not reported in the literature. Analysis of extensive literature data generally indicated three types of erosion-rate-versus-time curves. Two types (types 1 and 3) were observed in the present study; the third type involves incubation (and deposition), acceleration, and steady-state periods (type 2). Examination of the extensive literature data indicated that it is absolutely necessary to consider the corresponding stages or periods of erosion in correlating and characterizing erosion resistance of a wide spectrum of ductile materials.

Veerabhadrarao, P.↗

NASA NTRS1983

Vibration characteristics of hexagonal radial rib and hoop platforms

Experiment and analysis have been used to characterize the modes of vibration of planar radial rib and hoop hexagonal platforms. Finite element analysis correlated very well with experimental results. The sensitivity of mode shapes and frequencies to cable stiffness and initial tension is presented. Threshold values have been identified, above which changes in cable stiffness do not affect the first few platform vibration modes. Primary vibration modes of the radial rib platform involve beam bending. Vibration modes of the hoop platform exhibit both beam bending and frame bending and torsion. Results indicate for low order polygonal structures, the radial rib concept produced a higher fundamental frequency. For high order polygonal structures, the hoop concept has the potential to achieve a higher fundamental frequency than the radial rib concept.

Belvin, W. K.↗

NASA NTRS1986

Structure of the southern Rio Grande rift from gravity interpretation

Regional Bouguer gravity anomalies in southern New Mexico have been analyzed by two-dimensional wave number filtering and poly-nomial trend surface analysis of the observed gravity field. A prominent, regional oval-shaped positive gravity anomaly was found to be associated with the southern Rio Grande rift. Computer modeling of three regional gravity profiles suggests that this anomaly is due to crustal thinning beneath the southern Rio Grande rift. These models indicate a 25 to 26-km minimum crustal thickness within the rift and suggest that the rift is underlain by a broad zone of anomalously low-density upper mantle. The southern terminus of the anomalous zone is approximately 50 km southwest of El Paso, Texas. A thinning of the rifted crust of 2-3 km relative to the adjacent Basin and Range province indicates an extension of about 9 percent during the formation of the modern southern Rio Grande rift. This extension estimate is consistent with estimates from other data sources. The crustal thinning and anomalous mantle is thought to result from magmatic activity related to surface volcanism and high heat flow in this area.

Daggett, P. H.↗

NASA NTRS1988

Adaptive computational methods for aerothermal heating analysis

The development of adaptive gridding techniques for finite-element analysis of fluid dynamics equations is described. The developmental work was done with the Euler equations with concentration on shock and inviscid flow field capturing. Ultimately this methodology is to be applied to a viscous analysis for the purpose of predicting accurate aerothermal loads on complex shapes subjected to high speed flow environments. The development of local error estimate strategies as a basis for refinement strategies is discussed, as well as the refinement strategies themselves. The application of the strategies to triangular elements and a finite-element flux-corrected-transport numerical scheme are presented. The implementation of these strategies in the GIM/PAGE code for 2-D and 3-D applications is documented and demonstrated.

Price, John M.↗

NASA NTRS1991

BEST3D user's manual: Boundary Element Solution Technology, 3-Dimensional Version 3.0

The theoretical basis and programming strategy utilized in the construction of the computer program BEST3D (boundary element solution technology - three dimensional) and detailed input instructions are provided for the use of the program. An extensive set of test cases and sample problems is included in the manual and is also available for distribution with the program. The BEST3D program was developed under the 3-D Inelastic Analysis Methods for Hot Section Components contract (NAS3-23697). The overall objective of this program was the development of new computer programs allowing more accurate and efficient three-dimensional thermal and stress analysis of hot section components, i.e., combustor liners, turbine blades, and turbine vanes. The BEST3D program allows both linear and nonlinear analysis of static and quasi-static elastic problems and transient dynamic analysis for elastic problems. Calculation of elastic natural frequencies and mode shapes is also provided.

Source record↗

NASA NTRS1989

Linear estimation and control studies of vibration suppression of SCOLE flexible mast

A Kalman filter and a controller are presented for vibration suppression of the Spacecraft Control Laboratory Experiment flexible mast mounted in the cantilevered configuration. Mode shapes and frequencies of the structure obtained from a finite element analysis are used to compute the controller and filter gains. The paper presents results and discussion from simulation and experimental studies. Comparison of experimental results with those obtained by simulation show close agreement.

Ghosh, D.↗

NASA NTRS1991

Aerodynamic shape optimization of arbitrary hypersonic vehicles

A new method was developed to optimize, in terms of aerodynamic wave drag minimization, arbitrary (nonaxisymmetric) hypersonic vehicles in modified Newtonian flow, while maintaining the initial volume and length of the vehicle. This new method uses either a surface fitted Fourier series to represent the vehicle's geometry or an independent point motion algorithm. In either case, the coefficients of the Fourier series or the spatial locations of the points defining each cross section were varied and a numerical optimization algorithm based on a quasi-Newton gradient search concept was used to determine the new optimal configuration. Results indicate a significant decrease in aerodynamic wave drag for simple and complex geometries at relatively low CPU costs. In the case of a cone, the results agreed well with known analytical optimum ogive shapes. The procedure is capable of accepting more complex flow field analysis codes.

Dulikravich, George S.↗

NASA NTRS1993

Synthesis of polycrystalline chalcopyrite semiconductors by microwave irradiation

Polycrystalline samples of the chalcopyrites CuInS2, CuInSe2, and CuInSSe were prepared from stoichiometric mixtures of the pure elements by microwave irradiation. The reactions were performed in sealed quartz tubes in as few as 3 minutes. The products were analyzed by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, and X-ray photoelectron spectroscopy. The surface morphology and shape of the particles produced by this method suggest that the products are formed from liquid melts. This method could be applied to the production of bulk chalcopyrite as sources for thin film growth.

Landry, Christopher C.↗

NASA NTRS1993

A reciprocity formulation for the EM scattering by an obstacle within a large open cavity

A formulation based on a generalized reciprocity theorem is developed for analyzing the external high frequency EM scattering by a complex obstacle inside a relatively arbitrary open-ended waveguide cavity when it is illuminated by an external source. This formulation is also extended to include EM fields whose time dependence may be nonperiodic. A significant advantage of this formulation is that it allows one to break up the analysis into two independent parts; one deals with the waveguide cavity shape alone and the other with the obstacle alone. The external scattered field produced by the obstacle (in the presence of the waveguide cavity structure) is given in terms of a generalized reciprocity integral over a surface S(T) corresponding to the interior waveguide cavity cross section located conveniently but sufficiently close to the obstacle. Furthermore, the fields coupled into the cavity from the source in the exterior region generally need to propagate only one-way via the open front end (which is directly illuminated) to the interior surface S(T) in this approach, and not back, in order to find the external field scattered by the obstacle.

Pathak, Prabhakar H.↗

NASA NTRS1941

Tests of a Gust-Alleviating Wing in the Gust Tunnel

Tests were made in the NACA gust tunnel to determine the effectiveness of a torsionally flexible wing with the torsion axis ahead of the locus of the section aerodynamic centers in reducing airplane accelerations due to atmospheric gusts. For three gust shapes, a series of flights was made with the airplane model equipped with either a torsionally flexible or a rigid wing. The results indicated that the torsionally flexible wing reduced the maximum acceleration increment 5 percent for the sharp-edge gust and about 17 percent for gust shapes with gradient distances of 6.8 and 15 chord lengths. The analysis indicated that the effectiveness of this method of gust alleviation was independent of the gust velocity and that, for the same total load increment, the torsionally flexible wing would have 10 percent less bending-moment increment at the root section of the wing than a rigid wing in all but the sharpest gusts. The results also indicated that the torsionally flexible wing slightly increased the longitudinal stability of the airplane model in a gust.

Shufflebarger, C C↗

NASA NTRS1945

Propellers in yaw

It was realized as early as 1909 that a propeller in yaw develops a side force like that of a fin. In 1917, R. G. Harris expressed this force in terms of the torque coefficient for the unyawed propeller. Of several attempts to express the side force directly in terms of the shape of the blades, however, none has been completely satisfactory. An analysis that incorporates induction effects not adequately covered in previous work and that gives good agreement with experiment over a wide range of operating conditions is presented. The present analysis shows that the fin analogy may be extended to the form of the side-force expression and that the effective fin area may be taken as the projected side area of the propeller.

Ribner, Herbert S↗