Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Hall effect study of electron irradiated Si(Li)

Measurement of the Hall coefficient as a function of temperature between 15 and 300 K allows the separate determination of donor and acceptor concentrations in silicon samples which were irradiated at 240 K by 1-MeV electrons and then thermally annealed at 300 K. In both lithium- and phosphorus-doped silicon irradiation increased the acceptor concentration and decreased the donor concentration due to the formation of vacancy donor pairs. Annealing did not change either concentration in phosphorus-doped silicon and caused both concentrations to decrease in silicon doped with moderate amounts of lithium. In addition to this, in both lithium- and phosphorus-doped silicon the concentration and energy level of the A center were measured at each point in the sample's history. This experiment was limited to float-zoned silicon doped with less than 6 x 10 to the 14th power donors per cu cm.

Stannard, J.↗
NASA NTRS1971

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations. Phase 5A: Effects of torsional blade flexibility on single blade random gust response statistics

Quasi-steady aerodynamics were assumed, as well as a torsion mode where the amplitude is proportional to the distance from the rotor center. Aerodynamic torsional moment inputs are limited to the region of reverse flow where the aerodynamic center and the section center of gravity are separated by half the blade chord. Thus negligible effects of blade torsional flexibility are obtained for rotor conditions with negligible reverse flow effects. Numerical examples refer to conditions with 1.6 rotor advance ratio. It was found that the random flapping response is only moderately affected by torsional flexibility. However large random torsional loads and deflections occur even if flapping is completely suppressed. The coupling of the actual flapping motion into the blade torsional motion produces a substantial increase in the random torsional loads or deflections.

Hohenemser, K. H.↗
NASA NTRS1971

Analytic evaluation of display requirements for approach to landing

A computerized analysis procedure, based on a control theoretic model of the human pilot, is used to evaluate display requirements for longitudinal control in the landing approach. The display employed a digitally generated, perspective runway image with a superimposed artificial horizon for pitch indication. System performance measures are obtained for the approach phase of a light aircraft and a DC-8; predictions are made as to the effects of several display modifications. It is found that augmenting the basic display with glide slope reference bars and a velocity aim point yields adequate performance in calm air. Under moderate turbulence, the augmented display appears to be adequate for a DC-8 approach but not for a light aircraft.

Kleinman, D. L.↗
NASA NTRS1970

Remote detection of insect epidemics in conifers

With properly exposed color or infrared color film, discolored foliage caused by insect infestations in ponderosa pine is detectable on moderately small-scale photographs with acceptable accuracies. Black and white photographs which matched the wavebands of the ERTS multispectral scanner were combined into one additive color photo. This imagery was not as useful as photographs taken on color, color infrared, or color film with a minus blue filter. Based on the high-altitude color and color infrared photos obtained, it is concluded that only insect infestations larger than 100 meters in diameter are detectable on ERTS imagery.

Heller, R. C.↗
NASA NTRS1971

Mini gas-core propulsion concept

A propulsion concept is presented that can achieve specific impulses of 1000 to 2000 seconds for thrust levels on the order of 100 pounds (445 N) and maintain a small (1.22 m) reactor diameter for a total power-plant weight of approximately 10,000 kg. The concept combines a small (0.61 m) diameter spherical gas core centrally located, followed by a moderator (BeO-15 cm), surrounded by a driver fuel region and contained in a pressure vessel (ID of 1.22 m). Best results (i.e., highest ratio of cavity power to total power) occur with U-233 isotope as the fuel in both the cavity and the driver, although U-235 can also be used. Concept may also have application in the testing of a gas-core reactor and MHD devices and in high temperature-pressure materials research.

Hyland, R. E.↗
NASA NTRS1971

Design and preliminary testing of a Brayton space radiator concept

A low-temperature radiator has been designed to reject 17.62 kW of thermal power from an isotope Brayton power system. This power system has an electrical output of 7.1 kW. The total radiator consists of two radiators connected in series. Both radiators have a redundant coolant loop, shared fins, and are close to flight configuration. A silicone oil is used as the working fluid. Low flow rates and moderate pressure drop in the radiator required a small hydraulic diameter with large heat transfer area and large flow area. To obtain these characteristics and meet schedule limitations, an expanded tube configuration (with an approximately trapezoidal cross section) was selected. Because of the low flow rates and unconventional tube shape, small scale tests were performed to evaluate the validity of existing heat transfer and pressure drop correlations to this case. The results of these tests were in good agreement with predictions.

Miller, T. J.↗
NASA NTRS1971

Development of a space activity suit

The development of a series of prototype space activity suit (SAS) assemblies is discussed. The SAS is a new type of pressure suit designed especially for extravehicular activity. It consists of a set of carefully tailored elastic fabric garments which have been engineered to supply sufficient counterpressure to the body to permit subjects to breath O2 at pressures up to 200 mm Hg without circulatory difficulty. A closed, positive pressure breathing system (PPBS) and a full bubble helmet were also developed to complete the system. The ultimate goal of the SAS is to improve the range of activity and decrease the energy cost of work associated with wearing conventional gas filled pressure suits. Results are presented from both laboratory (1 atmosphere) and altitude chamber tests with subjects wearing various SAS assemblies. In laboratory tests lasting up to three hours, the SAS was worn while subjects breathed O2 at pressures up to 170 mm Hg without developing physiological problems. The only physiological symptoms apparent were a moderate tachycardia related to breathing pressures above 130 mm Hg, and a small collection of edema fluid in the hands. Both problems were considered to be related to areas of under-pressurization by the garments. These problems, it is suggested, can ultimately be corrected by the development of new elastic fabrics and tailoring techniques. Energy cost of activity, and mobility and dexterity of subjects in the SAS, were found to be superior to those in comparable tests on subjects in full pressure suits.

Annis, J. F.↗
NASA NTRS1971

Millimeter-wave generation with spiraling electron beams

The feasibility of using the interaction between a thin, solid, spiraling electron beam of 10 to 20 kV energy and a microwave cavity to generate watts of CW millimeter-wave power was investigated. Experimental results are given for several prototype devices operating at 9.4 GHz and at 94 GHz. Power outputs of 5 W, and electronic efficiencies near 3%, were obtained at X band, and moderate gain was obtained at 94 GHz. The small-signal theory gives a good fit to the X-band data, and the device behavior at 94 GHz is as expected from the given beam characteristics. The performance is limited chiefly by the velocity spread in the spiraling electron beam, and once this can be brought under control, high-power generation of millimeter waves appears quite feasible with this type of device.

Kulke, B.↗
NASA NTRS1972

Effect of environmental torques on short-term attitude prediction for a rolling-wheel spacecraft in a sun-synchronous orbit

A numerical evaluation and an analysis of the effects of environmental disturbance torques on the attitude of a hexagonal cylinder rolling wheel spacecraft were performed. The resulting perturbations caused by five such torques were found to be very small and exhibited linearity such that linearized equations of motion yielded accurate results over short periods and the separate perturbations contributed by each torque were additive in the sense of superposition. Linearity of the torque perturbations was not affected by moderate system design changes and persisted for torque-to-angular momentum ratios up to 100 times the nominal expected value. As these conditions include many possible applications, similar linear behavior might be anticipated for other rolling-wheel spacecraft.

Hodge, W. F.↗
NASA NTRS1971

An experimental study of the strength and stability of thin monocoque shells with reinforced and unreinforced rectangular cutouts

Axial compression tests were run on eleven thin-walled aluminum cylinders having rectangular cutouts. Various types of reinforcement were used around the cutouts, and some tests were run with no reinforcement. The test results are compared with the cylinder buckling loads prior to installation of the cutouts (obtained without damaging the cylinder by using a buckle-capture technique), and correlated with computer-predicted failure loads. The latter were based on the use of the STAGS computer program. For thin cylinders such as these, the test and computer-based analysis shows that for small to moderate size cutouts, reinforcement of the cutout is of no benefit unless the cylinder is of extremely high (geometrical) quality. For cylinder quality and cutout size where reinforcement is beneficial, the relative merits of the various reinforcement configurations are discussed, and an empirical basis for design is proposed.

Holmes, A. M. C.↗
NASA NTRS1971

Theoretical buckling loads of boron/aluminum and graphite/resin fiber composite anisotropic plates

Theoretical results are presented for the buckling of anisotropic plates. The plates are subjected to simple and combined in-plane loading. The plates are made from fiber composite material of boron/aluminum or high-modulus graphite/resin. The results are presented in nondimensional form as buckling load against fiber orientation angle for various plate aspect ratios. The results indicate that buckling loads of boron/aluminum plates are independent of fiber direction if the plate aspect ratios are greater than about 1, and moderately dependent when this ratio is less than about 1. In addition, the results indicate that the buckling loads are independent of aspect ratio for plates with aspect ratios greater than about 2. Boron/ aluminum composite plates can resist buckling loads more efficiently than graphite/resin composites on a specific buckling stress basis. The numerical algorithm and a listing of the computer code used to obtain the results are included.

Chamis, C. C.↗
NASA NTRS1971

Space shuttle staging simulation

The overall capability is described and delineated of a new digital computer program for simulation of space shuttle vehicle staging maneuvers. The important distinctive feature of the program is that it enables simulation of linkage-type separation devices (as well as all the more usual types) and includes the effects of interference aerodynamics and thrust impingement. A general flow description and a moderately detailed description of the major simulation components are presented. Some typical simulation results are shown, and the flexibility and growth potential of the basic simulation are discussed.

Hall, C. E.↗
NASA NTRS1971

The Advanced On-board Processor (AOP)

The goal of the Advanced On-Board Processor (AOP) development program is to design, build, and flight qualify a highly reliable, moderately priced, digital computer for application on a variety of spacecraft. Included in this development program is the preparation of a complete support software package which consists of an assembler, simulator, loader, system diagnostic, operational executive, and many useful subroutines. The AOP hardware/software system is an extension of the On-Board Processor (OBP) which was developed for general purpose use on earth orbiting spacecraft with its initial application being on-board the fourth Orbiting Astronomical Observatory (OAO-C). Although the OBP possesses the significant features that are required for space application, however, when operating at 100% duty cycle the OBP is too power-consuming for use on many smaller spacecraft. Computer volume will be minimized by implementing the processor and input/output portions of the machine with large scale integrated circuits. Power consumption will be reduced through the use of plated wire and, in some cases, semiconductor memory elements.

Hartenstein, R. G.↗
NASA NTRS1971

A Numerical Study of Displacement Body and Curvature Effects on Incompressible and Compressible Laminar Boundary Layers

This technique has been applied to study such effects on incompressible flow around cylinders at moderate to low Reynolds numbers and for compression ramps at hypersonic Mach numbers by employing a finite difference method to obtain numerical solutions. The results indicate that the technique can be applied successfully in both regimes and does predict the correct trend in regions of large curvature and displacement body effects. It was concluded that curvature corrections should only be attempted in cases where all displacement effects can be fully accounted for.

Wornom, S. F.↗
NASA NTRS1972

Electric field variations during substorms: OGO-6 measurements

The OGO-6 electric field measurements make it clear that the general pattern of high latitude electric fields in magnetic time-invariant latitude coordinates is not highly variable and that when unusual variations, or field distributions, occur they are relatively isolated in time and spatial extent. Thus, electric field changes on a global scale cannot, in general, be evoked as a direct cause of substorms. Polar traverses along the 18(h) to 6(h) magnetic time meridian show that the sum of potential drops across the evening auroral belt and morning auroral belt approximately equals the potential drop across the polar cap. The integrated polar cap potential drop ranges from 20 to 100 keV and values in the center of this range are most common under conditions of moderate magnetic disturbance. Roughly near 18(h) magnetic local time, a latitudinally narrow strip at the transition between auroral belt and polar cap fields exhibits unusually large field fluctuations immediately following the sudden onset of a negative bay at later magnetic local times. It appears likely that this spatially isolated correlation is related to an effect rather than a cause of substorm enhancement.

Heppner, J. P.↗
NASA NTRS1971

Conceptual design study of a nuclear Brayton turboalternator-compressor

A comprehensive analysis and conceptual design study of the turboalternator-compressor components using HeXe as the working fluid was performed. The study was conducted in three phases: general configuration analysis (Phase 1), design variations (Phase 2), and conceptual design study (Phase 3). During the Phase 1 analysis, individual turbine, alternator, compressor, and bearing and seal designs were evaluated. Six turboalternator-compressor (TAC) configurations were completed. Phase 2 consisted of evaluating one selected Phase 1 TAC configuration to calculate its performance when operating under new cycle conditions, namely, one higher and one lower turbine inlet temperature and one case with krypton as the working fluid. Based on the Phase 1 and 2 results, a TAC configuration that incorporated a radial compressor, a radial turbine, a Lundell alternator, and gas bearings was selected. During Phase 3 a new layout of the TAC was prepared that reflects the cycle state points necessary to accommodate a zirconium hydride moderated reactor and a 400 Hz alternator. The final TAC design rotates at 24,000 rpm and produces 160 kWe, 480 V, 3-phase, 400 hertz power.

Source record↗
NASA NTRS1971

Analysis of transient, linear wave propagation in shells by the finite difference method

The applicability of the finite difference method to propagation problems in shells, and the response of a cylindrical shell with cutouts to both longitudinal and radial transient excitations are investigated. It is found that the only inherent limitation of the finite difference method is its inability to reproduce accurately response discontinuities. The short wave length limitations of thin shell theory create significant convergence difficulties may often be overcome through proper selection of finite difference mesh dimensions and temporal or spatial smoothing of the excitation. Cutouts produce moderate changes in early and intermediate time response of a cylindrical shell to axisymmetric pulse loads applied at one end. The cutouts may facilitate the undesirable late-time transfer of load-injected extensional energy into nonaxisymmetric flexural response.

Geers, T. L.↗
NASA NTRS1972

Bleed Cycle Propellant Pumping in a Gas-Core Nuclear Rocket Engine System

The performance of ideal and real staged primary propellant pumps and bleed-powered turbines was calculated for gas-core nuclear rocket engines over a range of operating pressures from 500 to 5000 atm. This study showed that for a required engine operating pressure of 1000 atm the pump work was about 0.8 hp/(lb/sec), the specific impulse penalty resulting from the turbine propellant bleed flow as about 10 percent; and the heat required to preheat the propellant was about 7.8 MW/(lb/sec). For a specific impulse above 2400 sec, there is an excess of energy available in the moderator due to the gamma and neutron heating that occurs there. Possible alternative pumping cycles are the Rankine or Brayton cycles.

Gas-core↗