SEARCH · Engineering Papers

Results for “microstructure control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Additive Manufacture of Multi-Functional, Large-Scale Components

The poster summarizes the main results for a LDRD focused on developing a arc-based additive manufacturing (AM) system capable of fabricating large components with a composition gradient otherwise known as functionally graded materials (FGMs). FGMs are capable of addressing local extreme conditions in an optimal and cost-effective manner. The AM system (referred to as multi-Wire Arc Additive Manufacturing or m-WAAM) consisted of modifying a standard automated gas tungsten arc welding system to deliver multiple welding wires to the weld pool at controlled rates to deposit desired alloy compositions at critical locations. Numerous shapes and composition gradients were fabricated with the system and the effect of various deposition parameters on the nature of the composition profile were evaluated. Additionally, heat treatment of the FGM was performed to develop graded microstructures which should enhance dynamic impact performance of inexpensive steels. The project highlights the potential of m-WAAM to efficiently fabricate FGMs. However, this project only explored the science behind the technique and additional development work will be required to develop a fully-functional system that can build more complex components.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Interfacial-Strain-Controlled Ferroelectricity in Self-Assembled BiFeO 3 Nanostructures

Self-assembled BiFeO 3 -CoFe 2 O 4 (BFO-CFO) vertically aligned nanocomposites are promising for logic, memory, and multiferroic applications, primarily due to the tunability enabled by strain engineering at the prodigious epitaxial vertical interfaces. However, local investigations directly revealing functional properties in the vicinity of such critical interfaces are often hampered by the size, geometry, microstructure, and concomitant experimental artifacts. Ferroelectric switching in the presence of lateral distributions of vertical strain thus remains relatively unexplored, with broader implications for all strain-engineered functional devices. Additionally, by implementing tomographic atomic force microscopy, 3D domain orientation mapping, and spatially-resolved ferroelectric switching movies, local tensile strain significantly impacts the ferroelectric switching, principally by retarding domain nucleation in the BFO nearest to the vertically epitaxial tensile-strained interfaces. The relaxed centers of the BFO pillars become preferred domain nucleation and growth sites for low biases, with up to an order of magnitude change in the edge:center switching ratio for high biases. The new, multi-dimensional imaging approach—and its corresponding insights especially for directly strained interface effects on local properties—thereby advances the fundamental understanding of polarization switching and provides design principles for optimizing functional response in confined nanoferroic systems.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Exploring Domain-Wall Pinning in Ferroelectrics via Automated High-Throughput Atomic Force Microscopy

Domain-wall dynamics in ferroelectric materials are strongly position-dependent, since each polar interface is locked into a unique local microstructure. This necessitates spatially resolved studies of wall pinning using scanning-probe microscopy techniques. The pinning centers and pre-existing domain walls are usually sparse within the image plane, precluding the use of dense hyperspectral imaging modes and requiring time-consuming human experimentation. Here, a large-area epitaxial PbTiO 3 film on cubic KTaO 3 was investigated to quantify the electric-field-driven dynamics of the polar–strain domain structures using ML-controlled automated piezoresponse force microscopy. Analysis of 1500 switching events reveals that domain-wall displacement depends not only on field parameters but also on the local ferroelectric–ferroelastic configuration. For example, twin boundaries in polydomains regions, like a 1 – /c+ ∥ a 2 – /c – , stay pinned up to a certain level of bias magnitude and change only marginally as the bias increases from 20 to 30 V, whereas single-variant boundaries, like the a 2 + /c + ∥ a 2 – /c – stack, are already activated at 20 V. These statistics on the possible ferroelectric and ferroelastic wall orientations, together with the automated high-throughput AFM workflow, can be distilled into a predictive map that links domain configurations to pulse parameters. Here, this microstructure-specific rule set forms the foundation for the design of ferroelectric memories.

automated scanning probe microscopy↗

DOE OSTI2025

Coupled THM modeling of bentonite heating and hydration in tank tests with a new temperature-dependent water retention model

This study presents a coupled thermo-hydro-mechanical (THM) model for simulating the heating and hydration behavior of bentonite, a buffer material in deep geological repositories (DGRs). The model incorporates a new temperature-dependent soil water retention curve which captures the thermal-induced shift in water retention behavior. It also distinguishes between liquid and gas permeability, modeling intrinsic gas permeability as a function of accessible porosity to improve vapor transport and desaturation predictions. The model was validated against two large-scale tank tests, demonstrating good agreement with measured temperature, relative humidity, and water inflow data. It revealed a complex porosity evolution driven by thermal expansion, vapor movement, vapor condensation, and hydration-induced swelling during heating and hydration processes. The simulation results also suggest that the permeability of the hydration layer plays a critical role in controlling water intake. Clogging of this layer can significantly reduce the volume of water inflow during the hydration phase. Furthermore, while the model effectively captures key THM behavior, further development of the mechanical constitutive law is required to account for possible thermo-elasto-plastic volume changes and microstructural effects. Overall, the model provides a robust tool for evaluating the evolution of bentonite-based barrier material in DGRs.

Guo, Guanlong [Lawrence Berkeley National Laborato↗

DOE OSTI2023

Metallurgical and mechanical characterization of ATP-5 aluminum alloys for minimizing machining distortion

ATP-5 aluminum alloy was considered as an alternative to 6061-T651 aluminum alloy to minimize machining distortion. ATP-5 is a proprietary cast alloy that is compositionally similar to 5083 aluminum and is purported to have excellent machinability, stability, and corrosion response. Dimensional stability tests, mechanical testing, chemical analysis, microstructural analysis, and fractography were completed to understand the metallurgy of the ATP-5 alloy and assess its potential as a 6061-T651 alloy alternative. Ultimately, the ATP-5 was found to retain dimensional stability issues, albeit to a lesser extent, relative to the 6061-T651 alloy. Combined with the residual cast structure observed microstructurally and lot-to-lot mechanical property variation, the alloy was deemed not suitable for a structural application. Alternative uses of ATP-5 include tooling, molds, vacuum chucks, fixtures, and jigs, where the material can shine in non-load bearing applications with a need for dimensional control and machinability.

36 MATERIALS SCIENCE↗

NASA NTRS1982

Interrelation of material microstructure, ultrasonic factors, and fracture toughness of two phase titanium alloy

The pivotal role of an alpha-beta phase microstructure in governing fracture toughness in a titanium alloy, Ti-662, is demonstrated. The interrelation of microstructure and fracture toughness is demonstrated using ultrasonic measurement techniques originally developed for nondestructive evaluation and material property characterization. It is shown that the findings determined from ultrasonic measurements agree with conclusions based on metallurgical, metallographic, and fractographic observations concerning the importance of alpha-beta morphology in controlling fracture toughness in two phase titanium alloys.

Vary, A.↗

DOE OSTI2025

Elucidation of Local Ordering and Atomic-Scale Structure in Polymer-Derived SiOC

Silicon oxycarbide (SiOC) is a versatile ceramic material with tunable microstructure and compositions that can be modulated through precursor chemistry and processing conditions. Though there are several noteworthy uses of SiOC across a range of application spaces, the difficulties in elucidating the short- to medium-range order within these materials have limited the maturation of strategies to precisely control SiC x O 4–x compositions for user-tailored applications. In this contribution, we implement a range of synchrotron scattering and spectroscopy methods coupled with stochastic modeling techniques to elucidate changes in local chemistry and structure associated with the pyrolysis of a commercially available SiOC polymer precursor. Stochastic modeling approaches provide valuable insights into decoupling local Si–O and Si–C environments while confirming predominate heterogeneous phases in materials. Using pyrolysis temperatures between 250 to 800 °C results in a heterogeneous material predominately composed of SiOC and amorphous SiO 2 domains. At 1100 °C, redistribution of Si–C pairs in the SiOC network and Si–O from the SiO 2 domains create a more ordered SiOC phase with local cubic SiC-like ordering. In addition, residual carbon leads to a detectable carbon phases at 1100 °C that persist at higher temperatures. These efforts address the difficulties of obtaining atomic-scale insights into the local structure and nanoscale heterogeneities in SiOC, providing pathways toward establishing structure–property relationships for future materials development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2003

Flight Planning for the International Space Station - Levitation Observation of Dendrite Evolution in Steel Ternary Alloy Rapid Solidification (LODESTARS)

During rapid solidification, a molten sample is cooled below its equilibrium solidification temperature to form a metastable liquid. Once nucleation is initiated, growth of the solid phase proceeds and can be seen as a sudden rise in temperature. The heat of fusion is rejected ahead of the growing dendrites into the undercooled liquid in a process known as recalescence. Fe-Cr-Ni alloys may form several equilibrium phases and the hypoeutectic alloys, with compositions near the commercially important 316 stainless steel alloy, are observed to solidify by way of a two-step process known as double recalescence. During double recalescence, the first temperature rise is associated with formation of the metastable ferritic solid phase with subsequent conversion to the stable austenitic phase during the second temperature rise. Selection of which phase grows into the undercooled melt during primary solidification may be accomplished by choice of the appropriate nucleation trigger material or by control of the processing parameters during rapid solidification. Due to the highly reactive nature of the molten sample material and in order to avoid contamination of the undercooled melt, a containerless electromagnetic levitation (EML) processing technique is used. In ground-based EML, the same forces that support the weight of the sample against gravity also drive convection in the liquid sample. However, in microgravity, the force required to position the sample is greatly reduced, so convection may be controlled over a wide range of internal flows. Space Shuttle experiments have shown that the double recalescence behavior of Fe-Cr-Ni alloys changes between ground and space EML experiments. This program is aimed at understanding how melt convection influences phase selection and the evolution of rapid solidification microstructures.

Flemings, Merton C.↗

DOE OSTI2026

Temperature dependent interfacial microstructure in HIP-bonded Al6061/Zr joints

Pressing (HIP) at 450 °C and 560 °C under 103 MPa for 90 minutes to evaluate interfacial diffusion and microstructural evolution. Sound metallurgical bonding was achieved at both temperatures, with Zr serving as an effective diffusion barrier. Microstructural analysis revealed the the formation of a (Al,Si)3Zr intermetallic layer at the Al/Zr interface, whose thickness increased from ~100 nm at 450 °C to ~2100 nm at 560 °C, consistent with temperature-driven diffusion kinetics. The thin and continuous reaction layer observed at 450 °C indicates controlled interdiffusion and minimal reaction zone growth, favorable for maintaining interface stability and ductility. At 560 °C, enhanced atomic mobility led to pronounced intermetallic development, confirming diffusion-controlled growth behavior. These results provide valuable insights for optimizing Al/Zr interface design and diffusion barrier performance in advanced structural and energy systems.

Al/Zr interface↗

NASA NTRS1988

On the cyclic stress-strain behaviour of a Ni-base superalloy at room temperature

The cyclic stress-strain behavior of Nimonic alloy PE16 was studied at room temperature and at different aging conditions to determine whether the plateau in the cyclic stress-strain curve (CSSC) reported by Arbuthnot (1982) is typical of the room temperature behavior and/or some specific initial microstructural states. Specimen blanks were heat-treated in batches in Ar/H2 (98/2) atmosphere to produce gamma-prime precipitates of different average sizes, but with the volume fraction of gamma-prime precipitates kept constant at about 7 percent at all the heat-treatment conditions. Total axial strain controlled LCF tests were conducted under fully reversed loading (R = -1) at a constant strain rate of 0.004/s, using a servohydraulic machine. The load response in tension and compression was recorded continually, and stress-strain hysteresis loops were recorded at frequent intervals. In the present investigation, the CSSCs of the P16 alloy at room temperature did not display the plateaus reported by Arbuthnot.

Singh, Vakil↗

NASA NTRS1991

Pathophysiology of spontaneous venous gas embolism

The use of controllable degrees and durations of continuous isobaric counterdiffusion venous gas embolism to investigate effects of venous gas embolism upon blood, cardiovascular, and respiratory gas exchange function, as well as pathological effects upon the lung and its microcirculation is discussed. Use of N2O/He counterdiffusion permitted performance of the pathophysiologic and pulmonary microstructural effects at one ATA without hyperbaric or hypobaric exposures.

Lambertsen, C. J.↗

NASA NTRS1993

A study of fiber volume fraction effects in notched unidirectional SCS-6/Ti-15V-3Cr-3Al-3Sn composite

Notched unidirectional SCS-6/Ti-15-3 composite of three different fiber volume fractions (vf = 0.15, 0.37, and 0.41) was investigated for various room temperature microstructural and material properties including: fatigue crack initiation, fatigue crack growth, and fracture toughness. While the matrix hardness is similar for all fiber volume fractions, the fiber/matrix interfacial shear strength and matrix residual stress increases with fiber volume fraction. The composite fatigue crack initiation stress is shown to be matrix controlled and occurs when the net maximum matrix stress approaches the endurance limit stress of the matrix. A model is presented which includes residual stresses and presents the composite initiation stress as a function of fiber volume fraction. This model predicts a maximum composite initiation stress at vf approximately 0.15 which agrees with the experimental data. The applied composite stress levels were increased as necessary for continued crack growth. The applied Delta(K) values at crack arrest increase with fiber volume fraction by an amount better approximated using an energy based formulation rather than when scaled linear with modulus. After crack arrest, the crack growth rate exponents for vf37 and vf41 were much lower and toughness much higher, when compared to the unreinforced matrix, because of the bridged region which parades with the propagating fatigue crack. However, the vf15 material exhibited a higher crack growth rate exponent and lower toughness than the unreinforced matrix because once the bridged fibers nearest the crack mouth broke, the stress redistribution broke all bridged fibers, leaving an unbridged crack. Degraded, unbridged behavior is modeled using the residual stress state in the matrix ahead of the crack tip. Plastic zone sizes were directly measured using a metallographic technique and allow prediction of an effective matrix stress intensity which agrees with the fiber pressure model if residual stresses are considered. The sophisticated macro/micro finite element models of the 0.15 and 0.37 fiber volume fractions presented show good agreement with experimental data and the fiber pressure model when an estimated effective fiber/matrix debond length is used.

Covey, Steven J.↗

DOE OSTI2025

HPC for Optimizing Process Parameters to Control Material Evolution in Seamless Induction Hardening of Wind Turbine Main Shaft Bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2025

HPC for optimizing process parameters to control material evolution in seamless induction hardening of wind turbine main shaft bearings

17 WIND ENERGY↗

DOE OSTI2023

Controlling the Plastic Anisotropy of Magnesium Alloy by Tailoring the Grain Size and Yttrium Content

Hexagonal close-packed (HCP) magnesium alloys are widely used in automotive and aerospace industries due to their low density and high specific-strength. Their applicability is mainly restricted due to poor formability and pronounced plastic anisotropy. The formability is usually improved by altering the chemistry (adding rare-earth elements like Y) or modulating the microstructure (e.g., grain refinement). However, grain refinement alone cannot yield the desired ductility, and the scarcity of rare-earth elements also limits the extent to which the alloying strategy can be used. To overcome these issues, in this work, it is proposed that the formability of Mg alloys can be improved by combining the grain refinement and alloying approaches. To quantitively explore this possibility, a crystal-plasticity-based constitutive model, which is sensitive to both alloying concentration and grain sizes, is developed. To demonstrate, the model is applied to study the combined effect of Y content and grain size on the mechanical responses of Mg alloy. The calculations are used to build maps of plastic anisotropy measures, such as tension–compression asymmetry ratio and Lankford coefficients, for a wide range of Y content and grain sizes. From these maps, the grain size that would yield the desired performance of Mg alloy for a fixed Y content can be identified. This work provides an accelerated pathway to optimize both the microstructure and chemistry simultaneously to achieve formability and to reduce the dependence on alloying.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Spatially resolved phase transformation mapping in 410 stainless steel during additive manufacturing visualized via real-time infrared data

Here, in this study, we demonstrate that spatially resolved cooling curves derived from real-time infrared (IR) thermography during additive manufacturing (AM) can capture spatial variations in phase transformation temperatures through cooling curve analysis (CCA). Using this approach, we show that during laser hot-wire deposition of 410 stainless steel (410SS), the martensite start temperature (M s ) evolves dynamically throughout the build. The M s temperature is spatially nonuniform, ranging from 185 °C to 348 °C, with the lowest values toward the build center and higher values toward the upper region of the deposit. In the lower portion of the build, no M s inflection is detected via CCA, consistent with transformation occurring earlier during thermal cycling followed by tempering during subsequent thermal cycles. These trends in M s are corroborated by characterizing the microstructure by electron backscatter diffraction (EBSD). Traditionally, M s is assumed to be constant, and a single interpass temperature is applied during both deposition and residual stress modeling. Our results demonstrate that IR-derived cooling curves provide a route to spatially and temporally resolved transformation temperature tracking for dynamic interpass control and improved residual-stress modeling.

Additive manufacturing↗

DOE OSTI2020

Dynamic phase transformations in additively manufactured Ti-6Al-4V during thermo-mechanical gyrations

A complex interaction of process parameters, geometry and scan strategies in Additive Manufacturing (AM), can bring about spatial and temporal transients, i.e., Σ T ( x, y, z, time ), within a part. Published literature focusses on fluctuating thermal cycles on the microstructure evolution. However, the microstructural variations have not been correlated to dynamic flow behavior due to the macro- and micro-scale phenomena, i.e., accumulated plastic strains brought about by large thermal gradients, transformational strains and crystallographic misfit strains. Therefore, here we studied the mechanical response of Ti6Al4V alloys produced by AM under externally imposed controlled thermo-mechanical reversals in a Gleeble® thermo-mechanical simulator. The stress-strain behaviors were correlated to phase fractions, lattice strains, and also limited information on crystallographic texture using neutron diffraction techniques at the VULCAN Beamline at SNS, ORNL and also metallographic studies. The results are discussed and rationalized based on theories of static and dynamic phase transformations.

36 MATERIALS SCIENCE↗