Results for “laser processing” — Page 48

DOE OSTI2023

Photoinduced modification of optical properties of ferroelectric PZT thin films

This study investigates ultrafast photoinduced changes in optical properties of ferroelectrics (PZT) on femtosecond to nanosecond timescales, using broadband transient reflectivity studies. Surprisingly, spectral features were observed below the bandgap, which could not be attributed to ground state bleaching, excited state absorption, and/or stimulated emission. A model based on probe energy independent changes in refractive index and extinction coefficient showed good agreement with experimental results. Three relaxation processes were phenomenologically considered for the temporal evolution. Laser-induced heating was ruled out as the cause of short timescale behavior and photorefractive effect was suggested as a potential mechanism for changes in the optical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Exploring innovative pathway for SRF cavity fabrication

This article shows a study on an alternative pathway for the fabrication of a complete 1.3 GHz SRF cavity, aiming at improving production reliability, reducing the use of chemical polishing (EP or BCP) which is a costly and safety-critical step, and preserving surface quality after forming. Unlike the conventional pathway, the fabrication process is performed after polishing. This point is crucial as the used polishing technology could be applied only to flat geometries. The performed investigation demonstrates that damages during the fabrication process are considered minor, localized, and limited to the near-surface. Moreover, these studies confirm that the damaged layer (100-200 µm) is mainly caused by the rolling process, and not by the subsequent fabrication steps. A laser confocal microscope and SEM-EBSD technique were used to compare samples before and after forming. The preliminary results are discussed and presented in this paper.

Hryhorenko, O.↗

DOE OSTI2023

Molecules Functionalized with Cycling Centers for Quantum Information Science

The ability for a single molecule to produce enough laser-induced fluorescence to control and detect its quantum state is known as optical cycling. This property has been used to great effect in atoms, where the relatively small number of states promotes their ability to repeatedly fluoresce, for applications such as laser cooling, precision measurement, atomic clocks, and quantum information processing. The extension of this capability to molecular species, however, has been difficult, primarily due to their propensity to become vibrationally excited during illumination. This project brought together experts from atomic physics, physical chemistry, and computational quantum chemistry to develop means to create molecules capable of optical cycling. In particular, this program sought to produce an optical cycling center (OCC), a quantum functional group capable of chemical attachment to a wide variety of molecular hosts while retaining (and thereby furnishing to its host) the ability to optically cycle. Following our team’s theoretical identification of promising species, including alkaline-earth phenoxides, we then created these species and in many cases confirmed their optical cycle closure. We now not only know of the existence of a handful of large, molecular species that can be deployed for applications in quantum technologies and measurement, but have improved our knowledge of the molecular mechanisms leading to this discovery, which will enable generalization in the future. The extension of these ideas for informed chemical design of cycling molecules with bespoke properties is now being pursued by multiple groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Evaluation of LPBF Steels for Nuclear Applications

This report provides an update on the prioritization of existing reactor materials for advanced manufacturing. This report is a Milestone 3 deliverable in FY2023, under work package CT-23AN130401 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program here at Argonne National Laboratory (ANL). The focus of FY23 for ANL included the determination of a decision criteria matrix for the prioritization of existing materials, the literature review of a select few Fe-based alloys, and working with vendors to obtain customized powders. The work package also includes fabricating test samples in a Renishaw AM400 Laser Powder Bed Fusion (LPBF) system and optimizing the process parameters. The major outcomes of this work package are: With collaborations from PNNL, ORNL, and INL, we were able to establish a decision criteria matrix containing a total of 6 categories and 31 different criteria. These will be used to downselect alloys for further evaluation; As part of that, 6 different Fe-based alloys were selected, 3 austenitic stainless steels (A709, D9, AFA) and 3 ferritic/martensitic steels (HT9, Grade 91, Grade 92). Customized powders were obtained from vendors in small quantities to fabricate initial prints to check printability of these specific alloys; A total of 72 single track experiments were performed on two alloy systems, 1 austenitic stainless steel (A709) and 1 ferritic/martensitic steel (Grade 91) in order to optimize the process parameters for the full 3d prints. The optimization led to the selection of 20 different processing conditions, 10 for each class of alloys; D9 and AFA alloys showed extensive cracking and porosity in the samples. This was due to less-than-ideal conditions present in the chamber during the deposition. A709 printed using the same process parameters showed almost fully dense samples with no noticeable porosity or any other defects. SEM and EBSD analysis revealed single phase FCC microstructure with cellular structure within the grains; HT9, Grade 91, Grade 92 alloys also showed no noticeable signs of cracking and ImageJ analysis showed porosity <0.5% in all conditions. While Grade 91 and Grade 92 showed single phase BCC microstructures, the presence of martensite laths was noted in HT9 alloy; Future work will include further characterization of these alloys to better understand the microstructural evolution during the 3d printing process.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Recycling and Reuse of Tungsten-Rhenium Refractory Alloy Powder for Additive Manufacturing (Quarterly Progress Report - 01 April 2023-30 June 2023)

Savannah River National Laboratory in partnership with 6K Inc is working on demonstrating laser and electron-beam powder bed additive manufacturing processes of W-24Re alloy and developing powder reconditioning (deoxidation) technology via plasma spheroidization and investigating the properties and performance of additively manufactured W-24Re components produced using both virgin and recycled powders.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Exploring innovative pathway for SRF cavity fabrication

This article shows a study on an alternative pathway for the fabrication of a complete 1.3 GHz SRF cavity, aiming at improving production reliability, reducing the use of chemical polishing (EP or BCP) which is a costly and safety-critical step, and preserving surface quality after forming. Unlike the conventional pathway, the fabrication process is performed after polishing. This point is crucial as the used polishing technology could be applied only to flat geometries. The performed investigation demonstrates that damages during the fabrication process are considered minor, localized, and limited to the near-surface. Moreover, these studies confirm that the damaged layer (100-200 µm) is mainly caused by the rolling process, and not by the subsequent fabrication steps. A laser confocal microscope and SEM-EBSD technique were used to compare samples before and after forming. The preliminary results are discussed and presented in this paper.

Hryhorenko, O.↗

DOE OSTI2024

Schema Elements for Granta Annual Report: FY2024

Granta: Materials Intelligence (Granta: MI) is a commercial database software distributed by Ansys, Inc. that is utilized by the Nuclear Security Enterprise (NSE) to organize and store relevant materials data. Lack of standard and well-documented database schema is the primary obstacle to an NSE materials data management solution, so the objective of this project is to create and document such a schema. In FY21, an approach for designing, documenting, and managing a standard database schema was described based on the creation of schema elements (collections of attributes used to describe particular aspects of the data) to be used as building blocks for creating various database tables without duplication. In FY22, these methods were applied through a multi-site collaboration to create and document the schema elements necessary to build a thermogravimetric analysis (TGA) testing table. In FY23 the schema was expanded to include elements for a differential scanning calorimetry (DSC) table, along with schema for supporting metadata tables including Instruments, Projects, Documents, and Testing Series. In FY24 the following progress was made, again through multi-site collaboration: • The existing schema elements were modified to accommodate thermomechanical analysis (TMA) data, and a table, Test Data: TMA, was created for managing TMA data. • The elements necessary for the following additive manufacturing (AM) data tables (directed at data specific to selective laser sintering AM technology) were created: • AM Builds • AM Processes • AM Part Designs • Built AM Parts • AM Feedstock Materials • AM Feedstock Material Batches • The elements necessary for creating a Calibrated Material Models table were created, and the Calibrated Material Models table was created. In FY25 the existing schema will be deployed on the production enterprise Granta instance on the enterprise secure network. Schema elements will be appended, and new elements created as necessary, to allow the creation of tables specifically to support materials testing, AM process development, and design and analysis for modernization programs.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Design and Fabrication of a Temperature-Controlled Fueled Molten Salt Capsule Irradiation Experiment

Idaho National Laboratory (INL) is developing a Molten salt Research Temperature-controlled Irradiation (MRTI) experimental capsule for the Neutron Radiography (NRAD) reactor. The experiment is envisaged to be versatile and able to host a variety of salt-wall material combinations. The first test is designed to contain actinide-bearing chloride salt, which previously has not been subjected to a neutron field. The main objectives of the experiment are to produce irradiated salt samples for Post Irradiation Examination (PIE), to evaluate salt behavior under irradiation, and to test in-situ sensors/instrumentation. The final design for the experiment completed in 2022, and fabrication of the experiment is underway. The salt is double encapsulated providing insulation and redundancy in the case of leakage. A gas-gap between the inner capsule and the outer container enables tuning of thermal conduction to the NRAD coolant by altering its thickness and its gas-mixture. An inert gas mixture ratio in the gas-gap ensures the configurations reached a targeted average salt temperature of 600oC, while avoiding salt freezing or exceeding material limits. A resistive heater placed within a thermowell and controls the temperature of the experiment (both when the reactor is on or off). The selected configurations can contain over 10 cm3 of fuel-bearing chloride salt, which is sufficient for the purposes of the post-irradiation examination (PIE) and provides sufficient volume for two submerged thermocouple probes to monitor salt temperature. The capsule wall material is Inconel 625, and weld qualifications for the assembly have been developed. A glove-box laser weld technique was refined as part of this process to ensure a leak-tight assembly for the salt-bearing assembly and reduce the risks of impurities permeating into the salt. This work was supported through the INL Laboratory Directed Research & Development (LDRD) Program under DOE Idaho Operations Office Contract DE-AC07-05ID14517.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

ENYGF 2023 - Design of Temperature-controlled Fuel-salt Irradiation Experiment

Idaho National Laboratory (INL) is developing a Molten salt Research Temperature-controlled Irradiation (MRTI) experimental capsule for the Neutron Radiography (NRAD) reactor. The experiment is envisaged to be versatile and able to host a variety of salt-wall material combinations. The first test is designed to contain actinide-bearing chloride salt, which previously has not been subjected to a neutron field. The main objectives of the experiment are to produce irradiated salt samples for Post Irradiation Examination (PIE), to evaluate salt behavior under irradiation, and to test in-situ sensors/instrumentation. The final design for the experiment completed in 2022, and fabrication of the experiment is underway. The salt is double encapsulated providing insulation and redundancy in the case of leakage. A gas-gap between the inner capsule and the outer container enables tuning of thermal conduction to the NRAD coolant by altering its thickness and its gas-mixture. An inert gas mixture ratio in the gas-gap ensures the configurations reached a targeted average salt temperature of 600oC, while avoiding salt freezing or exceeding material limits. A resistive heater placed within a thermowell and controls the temperature of the experiment (both when the reactor is on or off). The selected configurations can contain over 10 cm3 of fuel-bearing chloride salt, which is sufficient for the purposes of the post-irradiation examination (PIE) and provides sufficient volume for two submerged thermocouple probes to monitor salt temperature. The capsule wall material is Inconel 625, and weld qualifications for the assembly have been developed. A glove-box laser weld technique was refined as part of this process to ensure a leak-tight assembly for the salt-bearing assembly and reduce the risks of impurities permeating into the salt. This work was supported through the INL Laboratory Directed Research & Development (LDRD) Program under DOE Idaho Operations Office Contract DE-AC07-05ID14517.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

X-ray tomography of damage dynamics in advanced materials using a laser wakefield accelerator

Additively manufactured (AM) metals offer the potential for customizable, cost-effective components, but qualification and certification are crucial. Key to this process is understanding pore dynamics under stress, typically analyzed using micro-computed tomography. This study introduces laboratory-scale “betatron” x-rays from laser wakefield acceleration as a high-throughput alternative for x-ray tomography of advanced materials, such as AM AlSi10Mg alloys. Coupled with 3D finite element modeling, this method provides detailed insights into stress-porosity interactions. The approach delivers high-resolution scans, revealing that pore shape and local triaxiality significantly influence fracture dynamics, supporting advanced material characterization. This work also demonstrates the potential and versatility of laser-betatron x-ray μCT for generating large datasets to accelerate our understanding of the stochastic, process-specific nature of pore formation in AM alloys.

Senthilkumaran, Vigneshvar↗

DOE OSTI2020

Femtosecond Laser Additive Manufacturing of Multi-Material Layered Structures

Laser additive manufacturing (LAM) of a multi-material multi-layer structure was investigated using femtosecond fiber lasers. A thin layer of yttria-stabilized zirconia (YSZ) and a Ni–YSZ layer were additively manufactured to form the electrolyte and anode support of a solid oxide fuel cell (SOFC). A lanthanum strontium manganite (LSM) layer was then added to form a basic three layer cell. This single step process eliminates the need for binders and post treatment. Parameters including laser power, scan speed, scan pattern, and hatching space were systematically evaluated to obtain optimal density and porosity. This is the first report to build a complete and functional fuel cell by using the LAM approach.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Unveiling the Mechanism of Photodamage to Sphingolipid Molecules via Laser Flash Photolysis and EPR

Abstract Sphingolipids are involved in the maintenance of the skin barrier function and regulate cellular processes of keratinocytes. The work reported here is designed to uncover details of the mechanism of damage to such lipids by UV radiation. Our approach employs laser flash photolysis and electron paramagnetic resonance (EPR) spectrometry to explore the mechanism of the decay reactions, and to determine the associated kinetic parameters. To interpret our experiments, we computed both excitation energies and EPR parameters of radicals formed during photolysis. Employing the spin‐trap EPR method confirmed the formation of both carbon‐ and nitrogen‐centered radicals. Thus, we can conclude that the photodecomposition of sphingolipids and their analogues proceeds by Norrish type I reactions with the formation of both nitrogen‐centered and alkyl radicals.

Biochemistry & Molecular Biology↗

DOE OSTI2021

Understanding Weld Formation and Microstructure Evolution in Laser Welded Stainless Steels and Ti-6Al-4V

High energy density welding processes are used for many industrial applications, such as aerospace and defense, and certain joint configurations and welding situations render post-weld inspection techniques difficult. Due to the inability to confirm penetration, there is a continual industrial need to improve prediction capabilities to aid in parameter selection. It is also necessary to understand the microstructural evolution to modify phase fractions and mitigate weldability related concerns such as solidification cracking or reduced corrosion performance.

42 ENGINEERING↗

DOE OSTI2022

Cross-beam energy transfer in direct-drive ICF. II. Theory and simulation of mitigation through increased laser bandwidth

The response of the cross-beam energy transfer instability (CBET) to laser bandwidth is investigated through a combination of theory and simulation. Existing linear theory is generalized to treat broadband lasers, demonstrating that CBET is most effectively suppressed when the bandwidth exceeds the ion-acoustic wave (IAW) frequency. It is shown that for such bandwidths, reverse (seed to pump) transfer becomes possible, which reduces the net energy transfer rapidly as bandwidth is increased. The CBET gain exponent in this regime scales with bandwidth (Δω) as Δω−3 for Gaussian or Lorentzian laser spectra with different scalings possible for other spectra. Comparison of our theory with linearized fluid and particle-in-cell simulations, performed with the laser-plasma simulation environment (LPSE) and vector particle in cell (VPIC) codes, respectively, finds that the model is accurate in the absence of nonlinear processes. However, linear analysis also finds that the IAW energy density scales as Δω−1, implying that nonlinear effects may be more difficult to control than the CBET scaling would suggest. Indeed, nonlinear effects are found to be present in VPIC simulations with high-intensity lasers, despite minimal apparent CBET. Nonlinear processes in the VPIC cases include particle trapping, the two-ion wave decay, and ion wave self-focusing. In some high intensity VPIC cases, these effects lead to net energy transfer from seed to pump and increases to backscatter stimulated Brillouin scattering reflectivities. Finally, for a given bandwidth, we show that improved control of nonlinear processes can be achieved via smoothing by spectral dispersion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Local prediction of Laser Powder Bed Fusion porosity by short-wave infrared imaging thermal feature porosity probability maps

We report that local thermal history can significantly vary in parts during metal Additive Manufacturing (AM), leading to local defects. However, the sequential layer-by-layer nature of AM facilitates in-situ part voxelmetric observations that can be used to detect and correct these defects for part qualification and quality control. The challenge is to relate this local radiometric data with local defect information to estimate process error likelihood in future builds. This paper uses a Short-Wave Infrared (SWIR) camera to record the temperature history for parts manufactured with Laser Powder Bed Fusion (LPBF) processes. The porosity from a cylindrical specimen is measured by ex-situ micro-computed tomography (μCT). Specimen data from the SWIR camera, combined with the μCT data, are used to generate thermal feature-based porosity probability maps. The porosity predictions made by various SWIR thermal feature-porosity probability maps of a specimen with a complex geometry are scored against the true porosity obtained via μCT. The receiver operating characteristic curves constructed from the predictions for the complex sample demonstrate the porosity probability mapping methodology’s potential for in-situ based porosity detection.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Effect of laser melt schedule on the microstructure of additively manufactured IN718 Superalloy

Laser powder bed fusion (L-PBF) has enabled the fabrication of geometrically complex metallic structures and components that are challenging to producing using conventional manufacturing approaches. The site-specific and far from equilibrium thermal conditions of L-PBF offer the potential to facilitate multi-length scale design of structure and properties across the atomic-through macro-levels. However, L-PBF systems face scalability challenges due to throughput constraints. Laser rotary powder bed fusion (L-RPBF) systems are being investigated as a solution to enhance the deposition rates compared to conventional L-PBF. Rotary systems also offer additional flexibility for controlling the time structure of melting through laser interleaving on alternating layers. Here, in this study, IN718 test samples were printed using single-laser or interleaved dual-laser configuration in a L-RPBF system to investigates the effect of process settings and melt-interleaving on as-fabricated microstructure. The microstructural evolution, such as grain size and crystallographic texture, was assessed by determining variations in the melt-pool shapes. Laser interleaving leads to a reduction in average grain size compared to single laser by ∼ 40 % at high power (400 W) and by ∼36 % at medium power (370 W). Results presented here identify key challenge for obtaining uniform microstructures and barriers for the broader adoption of high-deposition rate L-RPBF.

Dual-laser↗

DOE OSTI2021

Laser-Irradiated Holey Graphene-Supported Single-Atom Catalyst towards Hydrogen Evolution and Oxygen Reduction

Single-atom catalysts (SAC) can boost the intrinsic catalytic activity of hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). However, the challenge remains due to the complex synthesis process and insufficient stability. A sustainable approach is applied to synthesizing SACs through laser irradiation and gaining mesoporous graphene oxide (MGO). The surface dangling bonds of nitrogen-doped MGO (NMGO) extract metal atoms species from Co or Fe metal foams and convert them to SAC via an appropriate synthesis approach. Notably, the Co-NMGO electrocatalyst requires low potentials of 146 mV to convey a current density of 10 mA cm -2 towards HER. Similarly, the Fe-NMGO electrocatalyst offers an onset of 0.79 V towards ORR in acidic solution. The individual metal atoms are confirmed via aberration-corrected scanning transmission electron microscopy, and X-ray absorption near-edge structure and extended X-ray absorption fine structure. Density functional theory calculations by applying the grand canonical potential kinetics model revealed that Co-NMGO shows the optimum free reaction energy of -0.17 eV at -0.1 V for HER, and Fe-NMGO has less limiting potential than that of Co-NMGO for ORR case. Furthermore, this work opens a new approach towards the synthesis of SAC and its mechanistic understandings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Process-level cost analysis of hybrid manufacturing pathways for aerospace structural components

Hybrid manufacturing is a promising route for producing complex aerospace components, yet systematic cost benchmarking across multiple additive-subtractive pathways remains limited. This study presents a comprehensive process-based cost analysis of seven hybrid manufacturing routes, including laser powder bed fusion (L-PBF), powder- and wire-directed energy deposition (DED), wire arc additive manufacturing (WAAM), additive friction stir deposition (AFSD), metal binder jetting (MBJ), and agility forging, followed by scanning and finish machining. Parametric cost models incorporating direct material, labor, and energy costs were developed. L-PBF results are discussed in detail for a pickle fork component and directly compared with commercial pricing. Across all hybrid routes, labor emerged as the dominant cost driver, contributing more than 70% of total manufacturing cost in some cases. AFSD exhibited the lowest cost for aluminum components, with MBJ being its 316 L stainless steel counterpart, after accounting for geometric scaling. Benchmarking against industrial quotes suggests that hybrid manufacturing can achieve cost levels comparable to those of commercial services, although labor-intensive processes exhibit greater deviation. The analysis highlights automation of material handling, setup, and supervision as key opportunities for improving economic competitiveness. Overall, the proposed framework provides a quantitative basis for evaluating and optimizing hybrid manufacturing pathways for aerospace applications.

Baruah, Sweta [ORNL] (ORCID:0009000174256207)↗