SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technique which improves fiber alignment and reduces void content of thick laminated structures is readily applicable to structures that contain sections such as ribs, channels, or bosses joined to thin stems of same material.
Layup technique involving repositioning of filler plies and redesigning of bleeder pressure pad reduces wrinkles, voids, pores, and other defects at sharp bends in laminated materials.
Light-weight low-cost laminate used to replace epoxy compound panels is suitable for auto, railcar, and aircraft structural parts. Physical and thermal tests show panels made from formulation have better insulative properties, and burn cleaner with less toxic gas generation than panels made with conventional materials.
The finite element method is used to investigate the static behavior of laminated composite flat plates and cylindrical shells. The analysis incorporates the effects of transverse shear deformation in each layer through the assumption that the normals to the undeformed layer midsurface remain straight but need not be normal to the mid-surface after deformation. A digital computer program was developed to perform the required computations. The program includes a very efficient equation solution code which permits the analysis of large size problems. The method is applied to the problem of stretching and bending of a perforated curved plate.
The results of an experimental investigation on the fracture behavior of unidirectional and multidirectional laminated graphite/epoxy composites is reported. Critical tensile fracture stresses for constant head rate uniaxial specimens containing single-edge notches, double-edge notches, and centrally located circular holes are presented. Results are reported for loads and notches at various angles to the fiber direction. Evidence of notch sensitivity and stable crack growth is presented. Self-similar crack growth is shown to occur for only a limited set of circumstances. Critical stresses are compared to the theories of Waddoups et al and Whitney et al. These comparisons are presented using isotropic and orthotropic stress concentration factors together with a finite width correction factor. The results tend to show that use of only isotropic correction factors allow good correlation between theory and experiment.
Axial cracking in the load direction and transverse cracking across notched boron/epoxy laminate specimens subjected to tension/tension fatigue loading are studied both theoretically and experimentally. The fatigue analysis, which allows for the computation of residual strength and the determination of the preferred mode of crack propagation, is reviewed; static and fatigue data for boron/epoxy lamina are investigated with the aim of characterizing fatigue growth and residual strength as a function of the number of load cycles. It is suggested that correlation between the theory and the experiment may be limited by lack of a capability to predict the growth of delaminations.
A laminate composite containing an orthotropic layer with a crack situated normal to the interfaces, and bonded to two orthotropic half-planes of dissimilar materials, is considered. The solutions for two different classes of orthotropic materials are presented separately. In each case, the problem is first reduced to a system of dual integral equations, then to a singular integral equation which is subsequently solved numerically for the stress intensity factors at the tip of the crack. The effect of the material properties on the stress intensity factor is investigated. Two cases, the generalized plane stress and the plane strain, are treated simultaneously.
An orthotropic laminate composite containing a completely broken layer is considered. The problem is formulated in terms of integral transforms and then reduced to a singular integral equation which is solved numerically. The strength of stress singularity at the crack tip is determined from a characteristic equation which is obtained by studying the dominant part of the singular integral equation near the end points. The stress intensity factors are given for various material properties.
The effect of the thickness and the elastic properties of the adhesive layers in laminated structures is considered. The structure is assumed to consist of two sets of periodically arranged dissimilar layers which may contain cracks perpendicular to the interfaces. The crack problem is solved under the assumption of plane strain or generalized plane stress and by using two different models for the adhesive layers. In the first model the adhesive layer is approximated by a combination of tensile and shear springs. In the second the adhesive layer is considered to be an elastic continuum, hence involving no approximating assumptions. The results regarding the stress intensity and stress concentration factors obtained from these two models and that found by ignoring the adhesive layers are presented and some comparisons are made.
The effects of tensile load cycling and thermal cycling on residual stiffness and strength properties of the following composite and hybrid angle-ply laminates were studied: boron/epoxy, boron/polyimide, graphite/low-modulus epoxy, graphite/high-modulus epoxy, graphite/polyimide, S-glass/epoxy, graphite/Kevlar 49/epoxy, and graphite/S-glass/epoxy. Specimens of the first six types were mechanically cycled up to 90% of static strength. Those that survived 10 million cycles were tested statically to failure, and no significant changes in residual strength and modulus were noted. Specimens of all types were subjected to thermal cycling between room temperature and 411 K for the epoxy-matrix composites and 533 K for the polyimide-matrix composites. The residual strength and stiffness remained largely unchanged, except for the graphite/low-modulus epoxy, which showed reductions in both of approximately 35%. When low-temperature thermal cycling under tensile load was applied, there was a noticeable reduction in modulus and strength in the graphite/low-modulus epoxy and some strength reduction in the S-glass/epoxy.
Graphite/epoxy strengths at various moisture contents are estimated by extrapolating from small data base. With procedure, massive testing is unnecessary because advantage is taken of large data base already available for moisture content in laminates.
Lamination setup is used to produce void-free bonds by first employing vacuum to outgas materials and adhesive at temperature below curing temperature and then subjecting assembly to pressure and temperature necessary to cure.
The fatigue behavior of a notched, graphite/epoxy (T300/5208) laminate subjected to predominantly compressive loading was explored in a series of constant-amplitude and transport wing spectrum tests. Results of these tests indicate that (1) the amount of local (near the notch) buckling allowed in the tests significantly affected fatigue life; (2) spectrum truncation of either the high- or low-load end of the spectrum produced lives greater than those obtained in the baseline, complete-spectrum test, but life was much more sensitive to truncations at the high-load end; and (3) the Palmgren-Miner linear cumulative damage theory always predicted lives much longer than the actual spectrum loading test lives.
A turbine vane and associated endwalls designed for advanced gas turbine engine conditions are described. The vane design combines the methods of convection cooling and selective areas of full coverage film cooling. The film cooling technique is utilized on the leading edge, pressure side, and endwall regions. The turbine vane involves the fabrication of airfoils from a stack of laminates with cooling passages photoetched on the surface. Cold flow calibration tests, a thermal analysis, and a stress analysis were performed on the turbine vanes.
A three-parameter fatigue and residual strength degradation model has been proposed to predict statistically the fatigue behavior of composite laminae under axial shear loadings. The fatigue behavior includes the fatigue life and the fatigue damage expressed in terms of the residual strength degradation. An experimental test program using graphite/epoxy /+ or - 45 deg/2s laminates has been conducted to generate statistically meaningful data in order to examine the validity of the theoretical model. It is shown that the correlation between the theoretical predictions and the test results on the statistical distributions of the fatigue life and the residual strength is excellent. Test results on the shear modulus degradation are also presented and discussed in detail in order to provide insight for the establishment of a shear modulus degradation model.
The influence of edge effects on the tensile properties of angle-ply laminate composites can be eliminated by using edgeless (round tubular) specimens. However, uniaxial tests with such specimens, static and fatigue, have been generally unsuccessful because of the differential Poisson effect between the test section and the grips. An edgeless cylindrical specimen, developed to circumvent these difficulties, is examined in the present paper. It is a flattened tube consisting of two flat sides connected by curved sections. It can be handled much like the standard flat coupon. The flat ends of the specimen are provided with crossplied fiberglass gripping tabs, the same as used for flat test coupons. As part of the tabbing, the hollow ends must be plugged with inserts to prevent crushing of the ends. A special insert design was developed to minimize detrimental Poisson effects ordinarily introduced by inserts.
The paper presents a method for designing laminated plates with orthotropic layers under uniaxial and biaxial compression. The objective is to find the fiber direction of all the layers that give the highest buckling stress; therefore, it is necessary to solve an unconstrained maximization problem. The optimization technique used is Powell's conjugate direction method. Numerical calculations were made for plates with three, four, and six layers.
The degree of notch sensitivity of composites in compression and whether their failures can be predicted over a wide range of plate and hole sizes. The notch sensitivity of composites is investigated by comparing actual failure loads of laminates with circular holes, with the extreme failure that would be expected from an ideal notch insensitive material and from an ideal notch sensitive material. The predictability question is addressed by applying the point stress failure criterion to a wide range of plate widths and hole sizes and comparing with available experimental data. The severity of impact is explored by comparing strength reductions resulting from impact with those resulting from comparable size circular holes. Finally, comparison is made of the differences to be expected from the effects of cracks and circular holes on failure strength.