Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Comparison of passivation properties of plasma-assisted ALD and APCVD deposited Al 2 O 3 with SiN x capping

In this paper, we report on the direct comparison of Al 2 O 3 films deposited by plasma-assisted atomic layer deposition (ALD) and atmospheric pressure chemical vapor deposition (APCVD) techniques on the passivation properties of both bare and boron diffused Si surfaces. It is found that ALD and APCVD deposited Al 2 O 3 layers with SiN x capping have very similar chemical composition, hydrogen concentration at the Al 2 O 3 /Si interface, and interface defect density (D it ), but the ALD film has slightly higher negative fixed charge (Q f ) after a high temperature (~750 °C) contact firing cycle typically used for solar cell fabrication. Both films showed excellent surface recombination velocities of <5 cm/s on planar and textured un-diffused Si wafers, but the ALD films gave 1 to 8 fA/cm 2 lower emitter saturation current densities (J 0e ) on implanted boron emitters with sheet resistance in the range of 90–180 Ω/. This is attributed to the observed slightly higher negative charge-induced field-effect passivation in the ALD films. However, SiN x /Al 2 O 3 /p + /n/n + passivated emitter rear totally diffused (PERT) cell structures fabricated with 110 and 150 Ω/ emitter in this study showed no appreciable difference in cell efficiency. Device analysis and simulations showed that even for >23% high-performance solar cells design, with very low bulk and rear contact recombination, the observed small difference in J 0e has negligible effect on cell efficiency. Furthermore, APCVD Al 2 O 3 passivation of B emitter can produce comparable efficiencies to their counterpart ALD Al 2 O 3 passivated n-type Si solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Serial femtosecond crystallography on in vivo-grown crystals drives elucidation of mosquitocidal Cyt1Aa bioactivation cascade

Cyt1Aa is the one of four crystalline protoxins produced by mosquitocidal bacterium Bacillus thuringiensis israelensis (Bti) that has been shown to delay the evolution of insect resistance in the field. Limiting our understanding of Bti efficacy and the path to improved toxicity and spectrum has been ignorance of how Cyt1Aa crystallizes in vivo and of its mechanism of toxicity. Here, we use serial femtosecond crystallography to determine the Cyt1Aa protoxin structure from sub-micron-sized crystals produced in Bti. Structures determined under various pH/redox conditions illuminate the role played by previously uncharacterized disulfide-bridge and domain-swapped interfaces from crystal formation in Bti to dissolution in the larval mosquito midgut. Biochemical, toxicological and biophysical methods enable the deconvolution of key steps in the Cyt1Aa bioactivation cascade. We additionally show that the size, shape, production yield, pH sensitivity and toxicity of Cyt1Aa crystals grown in Bti can be controlled by single atom substitution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Capping layer influence and isotropic in-plane upper critical field of the superconductivity at the FeSe / SrTiO 3 interface

Understanding the superconductivity at the interface of FeSe/SrTiO 3 is a problem of great contemporary interest due to the significant increase in critical temperature (T c ) compared to that of bulk FeSe, as well as the possibility of an unconventional pairing mechanism and topological superconductivity. We report a study of the influence of a capping layer on superconductivity in thin films of FeSe grown on SrTiO 3 using molecular beam epitaxy. We used in vacuo four-probe electrical resistance measurements and ex situ magnetotransport measurements to examine the effect of three capping layers that provide distinct charge transfer into FeSe: insulating FeTe, nonmetallic Te, and metallic Zr. Our results show that FeTe provides an optimal cap that barely influences the inherent T c found in pristine FeSe/SrTiO 3 , while the transfer of holes from a nonmetallic Te cap completely suppresses superconductivity and leads to insulating behavior. Finally, we used ex situ magnetoresistance measurements in FeTe capped FeSe films to extract the angular dependence of the in-plane upper critical magnetic field. Our observations reveal an almost isotropic in-plane upper critical field, providing insight into the symmetry and pairing mechanism of high-temperature superconductivity in FeSe.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Highly Reliable Multi-Port Smart Inverter Modules for PV-Based Energy Systems

Generally, large electrolytic capacitors (E-caps) are required to decouple the double-line frequency power fluctuation inherent in all single-phase dc-ac or ac-dc converters. These E-caps pose the weak link in the photovoltaic (PV) inverter because they have poor reliability as a result of short life expectancy and higher equivalent series resistance (ESR) which leads to lower system efficiency. In this paper, multiport smart dual-inverter modules are proposed for residential PV inverter systems with balanced outputs to eliminate the requirement of large decoupling capacitors, thus leading to more reliable and highly efficient inverter modules. The balanced dual outputs are controlled in phase quadrature such that the double frequency current is completely eliminated. One phase supports the standalone residential loads, and the other phase interfaces with the grid, which is synchronized to the utility grid. Also, the proposed modular configuration is scalable to accommodate higher power rating by stacking and paralleling multiple modules. Simulation results for the dual-inverter modules rated for 1 kW each are presented to validate the proposed concept. Experimental results from a controller hardware-in-the-loop (CHIL) platform also verify its feasibility.

14 SOLAR ENERGY↗
DOE OSTI2022

High Strength Steel-Aluminum Components by Vaporizing Foil Actuator Welding

This project aimed to address the challenge of effectively welding dissimilar materials—high-strength steel and high-strength aluminum for creating lightweight, multi-material automotive components. For automotive companies, reducing weight of a vehicle is critical task regulated by the government to solve the issue of greenhouse gas emissions. Production of lightweight cars and trucks can be achieved by substitution of current all-steel structures with multi-material lightweight structures that include high strength-to-weight-ration materials such as high-strength steels, aluminum alloys, magnesium alloys, titanium alloys, coupled with lightweight designs. This requires dissimilar metal welding, which is challenging for state of the art joining processes such as resistance spot welding. The cycle of melting-cooling-freezing during traditional welding that can easily ruin the designed outstanding properties of the advanced base metals, such as aluminum alloys, making the welded area much weaker than the base metals. To weld two different metals with great difference in melting points, such as aluminum and steel, it’s even more difficult or impossible because of the formation of brittle intermetallic compounds at the welded interface. In this project, a novel welding method, developed at OSU, was selected for validation and development. This novel technology enables welding by impact without melting and proves to be robust to join various dissimilar lightweight metals. Termed as vaporizing foil actuator welding or VFAW, the technology uses a thin aluminum foil that is rapidly vaporized by a high current pulse to produce an explosive-like pressure pulse to drive one metallic piece into another at the high speed required for impact welding. This project entailed development of the early-stage welding technology in terms of (a) the consumables, the welding apparatus and the power sources, (b) coupon scale screening of many material combinations including corrosion studies, (c) computational modeling and design of the welded interface as well as of the multi-material prototype component, and (d) mechanical testing for strength and durability at coupon scale and to a certain extent the prototype scale. The all-steel engine cradle of 2016 Chevrolet Cruze was chosen as the baseline prototype component. The target set for the project was to demonstrate a 20% weight reduction at a cost premium of less than $\$ $5/lb saved without compromising on baseline mechanical properties. At project completion, a 12% lighter prototype component was demonstrated with an estimated cost premium of $\$ $9.8/lb saved. Besides prototype level demonstration of the technology, this project also enabled elevation of the technology’s readiness level to where a hydraulically actuated welding head was developed and made ready for deployment at a research and development facility for Tier 1 automotive supplier.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Current-Activated Reactive Ultrafast Joining (CARUJ)

We have demonstrated Current Activated Reactive Ultrafast Joining (CARUJ) as a novel approach for rapid fabrication of similar and dissimilar materials, such as ceramic-ceramic and ceramic-metal joint assemblies. The CARUJ technology utilizes resistive heating of carbon-based materials to apply localized heat at, (through or around) joint zones at rates of 10 1 -10 2 ˚C/min, enabling joining at time scales considerably shorter (several minutes as opposed to hours) than conventional approaches for similar systems. Herein, we present our findings while evaluating the CARUJ concept. Three methods of heat application were evaluated: (i) using carbon joule heating elements to apply heat directly through the joint interface; (ii) using flexible joule heating elements to locally apply heat around the assembly interface; and (iii) non-contact heating of the joint assembly using inductive power. Schemes (ii) and (iii) proved to be the most effective in producing mechanically sound reliable joints. We demonstrated single-step fabrication of dense SiC-SiC joints with a Si- SiC interface using minimal pressure (1–2 MPa) in under 30 minutes. Measured average joint strengths of about 15 MPa are initially achieved for joined bodies when tested in single lap offset (SLO) compressive shear, while tuning of the interfacial composition along with a reduction in interlayer thickness, results in improved joint strengths of approximately 43 MPa. We further demonstrated SiC-SiC joining using Active Brazing Alloys (ABAs) proof of concept joining of tubular geometries. The versatility of CARUJ is demonstrated by utilizing non-contact heating via induction, to join dissimilar materials systems of SiC, SS316 and MAX phase ceramics with ABA interlayers. The localized and rapid heat application realizes a versatile material joining technique that can be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Influence of cobalt, tantaum and tungsten on the high temperature mechanical properties of single crystal nickel-base superalloys

For alloys with the baseline refractory metal level of 3 percent Ta and 10 percent W, decreases in Co level from 10 to 0 percent resulted in increased tensile strength and creep resistance. Substitution of W for Ta resulted in decreased creep life at high stresses but improved life at low stresses. Substitution of Ni for Ta caused large reductions in tensile strength and creep resistance, and corresponding increases in ductility. For these alloys with low Ta plus W totals, strength was independent of Co level. The increases in tensile strength with increases in refractory metal content were related to the increases in gamma volume fraction and solid solution hardening. Increases in strength as Co level decreased were considered to be the result of coherency strain hardening from the increased lattice mismatch. Dislocation shear through the gamma-gamma interface is considered to be the rate limiting step in the deformation process.

Nathal, M. V.↗
NASA NTRS1993

Caps Seal Boltholes On Vacuum-System Flanges

Sealing caps devised for boltholes on vacuum-system flanges. Used in place of leak-prone gaskets, and provide solid metal-to-metal interfaces. Each sealing cap contains square-cut circular groove in which O-ring placed. Mounted on studs protruding into access ports, providing positive seal around each bolthole. Each cap mates directly with surface of flange, in solid metal-to-metal fit, with O-ring completely captured in groove. Assembly immune to misalignment, leakage caused by vibration, and creeping distortion caused by weight of port. O-ring material chosen for resistance to high temperature; with appropriate choice of material, temperature raised to as much as 315 degrees C.

Roman, Robert F.↗
NASA NTRS2013

NASA Tech Briefs, Februrary 2013

Topics covered include: Measurements of Ultra-Stable Oscillator (USO) Allan Deviations in Space; Gaseous Nitrogen Orifice Mass Flow Calculator; Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards; Rover Low Gain Antenna Qualification for Deep Space Thermal Environments; Automated, Ultra-Sterile Solid Sample Handling and Analysis on a Chip; Measuring and Estimating Normalized Contrast in Infrared Flash Thermography; Spectrally and Radiometrically Stable, Wideband, Onboard Calibration Source; High-Reliability Waveguide Vacuum/Pressure Window; Methods of Fabricating Scintillators With Radioisotopes for Beta Battery Applications; Magnetic Shield for Adiabatic Demagnetization Refrigerators (ADR); CMOS-Compatible SOI MESFETS for Radiation-Hardened DC-to-DC Converters; Silicon Heat Pipe Array; Adaptive Phase Delay Generator; High-Temperature, Lightweight, Self-Healing Ceramic Composites for Aircraft Engine Applications; Treatment to Control Adhesion of Silicone-Based Elastomers; High-Temperature Adhesives for Thermally Stable Aero-Assist Technologies; Rockballer Sample Acquisition Tool; Rock Gripper for Sampling, Mobility, Anchoring, and Manipulation; Advanced Magnetic Materials Methods and Numerical Models for Fluidization in Microgravity and Hypogravity; Data Transfer for Multiple Sensor Networks Over a Broad Temperature Range; Using Combustion Synthesis to Reinforce Berms and Other Regolith Structures; Visible-Infrared Hyperspectral Image Projector; Three-Axis Attitude Estimation With a High-Bandwidth Angular Rate Sensor Change_Detection.m; AGATE: Adversarial Game Analysis for Tactical Evaluation; Ionospheric Simulation System for Satellite Observations and Global Assimilative; Modeling Experiments (ISOGAME); An Extensible, User- Modifiable Framework for Planning Activities; Mission Operations Center (MOC) - Precipitation Processing System (PPS) Interface Software System (MPISS); Automated 3D Damaged Cavity Model Builder for Lower Surface Acreage Tile on Orbiter; Mixed Linear/Square-Root Encoded Single-Slope Ramp Provides Low-Noise ADC with High Linearity for Focal Plane Arrays; RUSHMAPS: Real-Time Uploadable Spherical Harmonic Moment Analysis for Particle Spectrometers; Powered Descent Guidance with General Thrust-Pointing Constraints; X-Ray Detection and Processing Models for Spacecraft Navigation and Timing; and Extreme Ionizing-Radiation-Resistant Bacterium

Source record↗
DOE OSTI2025

A constrained-transport embedded boundary method for compressible resistive magnetohydrodynamics

Motivated by the increased interest in pulsed-power magneto-inertial fusion devices in recent years, we present a method for implementing an arbitrarily shaped embedded boundary on a Cartesian mesh while solving the equations of compressible resistive magnetohydrodynamics. The method is built around a finite volume formulation of the equations in which a Riemann solver is used to compute fluxes on the faces between grid cells, and a face-centered constrained transport formulation of the induction equation. The small time step problem associated with the cut cells is avoided by always computing fluxes on the faces and edges of the Cartesian mesh. We extend the method to model a moving interface between two materials with different properties using a ghost-fluid approach, and show some preliminary results including shock-wave-driven and magnetically-driven dynamical compressions of magnetohydrostatic equilibria. In conclusion, we present a thorough verification of the method and show that it converges at second order in the absence of discontinuities, and at first order with a discontinuity in material properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Solvent-induced membrane stress in biofuel production: molecular insights from small-angle scattering and all-atom molecular dynamics simulations

The disruptive effect of organic solvents on microbial membranes represents a significant challenge to the economical production of green fuels and value-added chemicals from lignocellulosic feedstocks. One route to overcoming this challenge is to engineer microbes with membranes capable of resisting organic solvent stresses. In this regard, it is useful to understand the mechanisms by which organic solvents disrupt typical biomembranes. In this study, molecular dynamics (MD) simulation, complemented by small-angle X-ray and neutron scattering (SANS/SAXS), provide a molecular-scale view of the disruption of a microbial model membrane by 1-butanol and tetrahydrofuran (THF), two common water–organic cosolvent mixtures of importance in biofuel production. Solvent interactions at the interface between the head-group and fatty acid tail regions lead to more dramatic membrane changes than interactions solely at the head-groups or tails. Although both organic solvents are found to partition into the membrane, the depth of solvent penetration into the membrane is quite different. Specifically, 1-butanol localizes near the interface between the lipid heads and tails at low concentrations, but partitions into both the head and tail regions at high concentrations. In contrast, THF, overall, partitions less than 1-butanol and prefers the lipid tail regions. Importantly, the presence of 1-butanol near the head/tail interface introduces drastic membrane changes not seen with THF. The organic solvent interactions with the lipids lead to membrane thinning and fluidization, but more so for 1-butanol than for THF. These results suggest that an aim for the future engineering of robust membranes could be to design lipid head groups that reduce the accumulation of organic solvents at the head–tail interface and that rational designs need also be cognizant of the different solvent-specific mechanisms responsible for membrane disruption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Module-Level Thermal Interface Material Degradation in HALT

Abstract In this study, thermal interface material (TIM) degradation is driven through highly accelerated life test (HALT) using temperature cycling with a prescribed vibrational acceleration for two commercially available materials having thermal conductivities of 6.0 and 8.5 W/m K. HALT specimens were prepared by applying TIM through a 4-mil stencil over AlSiC baseplates in the shape of those used in Wolfspeed CAS325M12HM2 power electronics modules. Baseplates were mounted onto aluminum carrier blocks with embedded thermocouples to characterize the thermal resistance across the baseplate and TIM layer. Thermal dissipation into the top of the baseplates was provided by a custom heating block, which mimics the size and placement of the die junctions in CAS325 modules, applying power loads of 200, 300, and 400 W. After initial characterization, samples were transferred to the HALT chamber with one set of samples exposed to temperature cycling only (TCO) and the other temperature cycling and vibration (TCV). Both sample sets were cycled between temperature extremes of −40 °C and 180 °C with vibrations applied at a peak acceleration of 3.21 Grms. After hundreds of cycles, samples were reevaluated to assess changes in thermal resistance to provide an accelerated measure of TIM degradation. This allows for reliability prediction of useful lifetime (illustrated in a solar inverter case study herein), as well as to provide a basis for developing an accelerated testing method to related temperature cycling to faster methods of degradation. Such techniques provide a means to develop maintenance schedules for power modules for ensuring sufficient thermal performance over the operating lifetime.

Engineering↗
DOE OSTI2020

Transport Processes in a Li-ion Cell during an Internal Short-Circuit

Internal short-circuit in a lithium-ion cell causes an abrupt increase in cell temperature and triggers subsequent thermal runaway. In this work, we present a detailed electrochemical-thermal model to investigate the physical behavior during an internal short-circuit. Simulations at wide range of heat transfer coefficients and short-circuit resistances are conducted to illustrate electrochemical and thermal behavior under a wide range of conditions. The Joule heating at the shorted region promotes electrochemical reactions nearby, causing in-plane non-uniformity of electrolyte and active material transport. Furthermore, it is found that diffusion in solid active materials plays a significant role at very high shorting currents (~20 C), as electrochemical reactions rate are being controlled progressively more by availability of Li + at the interface, due to limitations in diffusion through the active material with increasing discharge rates. This diffusion limitation causes a drop in available energy, and subsequently a decrease in cell equilibrium potential and the heat generation rate at the location of the short. On the other hand, rapid depletion of lithium concentration in the electrolyte and accumulation on the electrode surface results in highly non-uniform transport properties resulting in higher heat generation rates. Hence, the heating regime shifts from "local heating" to "global heating". Based on the findings, important design parameters for battery safety are discussed.

25 ENERGY STORAGE↗
DOE OSTI2026

GaN Core-shell Nanofin Vertical Transistor (CoNVerT): A New Direction for Power Electronics (Final Scientific/Technical Report)

A novel power transistor architecture, the GaN c ore-shell n anofin ver tical transistor (CoNVerT) to address fundamental challenges in realizing the ultimate limit of GaN power transistor performance was explored experimentally. This technology promises ultra-high-efficiency high voltage/high power applications (e.g. DC/DC converters, motor control, fast charging, actuation), as well as to operate in harsh environments. The device exploits a vertical superjunction structure based on an experimentally-validated core-shell nanofin growth process in which lateral p-n heterojunctions are formed in a single growth step, while still maintaining vertical current flow for compact die size and low cost. The concept leverages the best properties of GaN for mid-range voltage applications: high mobility, high breakdown voltage, and native heterojunction enhancement-mode operation. Due to the crystallographic nature of the nanofin growth by molecular beam epitaxy, the sidewall heterojunctions occur on non-polar planes, resulting in ultra-smooth interfaces for high mobility, no sidewall etch damage and related surface/interface states, and elimination of piezoelectric effects that can limit reliability in conventional structures. This also facilitates superjunction formation for maximum device performance, and the selective-area growth of the nanofin results in dislocation-free growth, even on low-cost Si (111) substrate. In this program, core-shell nanofins were grown by molecular beam epitaxy, test structures to evaluate the doping, resistivity, and other electrical properties were fabricated, and the material and test structures were characterized in detail. The work identified clear potential (e.g., the doping was well controlled as required for superjunction concepts), but also additional areas that require additional effort to resolve (some unexpected crystal defects were encountered that require additional engineering to overcome). Simulation studies of the proposed concept validate that the fundamental approach is very promising, but additional effort in experimental realization is needed.

42 ENGINEERING↗
NASA NTRS2002

The Surface Interface Characteristics of Vertically Aligned Carbon Nanotube and Graphitic Carbon Fiber Arrays Grown by Thermal and Plasma Enhanced Chemical Vapor Deposition

The development of nano-arrays for sensors and devices requires the growth of arrays with the proper characteristics. One such application is the growth of vertically aligned carbon nanotubes (CNTs) and graphitic carbon fibers (GCFs) for the chemical attachment of probe molecules. The effectiveness of such an array is dependent not only upon the effectiveness of the probe and the interface between that probe and the array, but also the array and the underlaying substrate. If that array is a growth of vertically aligned CNTs or GCFs then the attachment of that array to the surface is of the utmost importance. This attachment provides the mechanical stability and durability of the array, as well as, the electrical properties of that array. If the detection is to be acquired through an electrical measurement, then the appropriate resistance between the array and the surface need to be fabricated into the device. I will present data on CNTs and GCFs grown from both thermal and plasma enhanced chemical vapor deposition. The focus will be on the characteristics of the metal film from which the CNTs and GCFs are grown and the changes that occur due to changes within the growth process.

Delzeit, Lance↗
DOE OSTI2020

Single-layer graphene as a highly selective barrier for vanadium crossover with high proton selectivity

In this paper, we report near-zero crossover for vanadium cross-permeation through single-layer graphene immobilized at the interface of two Nafion® polymer electrolyte membranes. Vanadium ion diffusion and migration, including proton mobility through membrane composites, were studied with and without graphene under diffusion and migration conditions. Single-layer graphene was found to effectively inhibit vanadium ion diffusion and migration under specific conditions. The single-layer graphene composites also enabled remarkable ion transmission selectivity improvements over pure Nafion® membranes, with proton transport being four orders of magnitude faster than vanadium ion transport. Resistivity values of 0.02 ± 0.005 Ω cm 2 for proton and 223 ± 4 Ω cm 2 for vanadium ion through single atomic layer graphene are reported. This high selectivity may have significant impact on flow battery applications or for other electrochemical devices where proton conductivity is required, and transport of other species is detrimental. Our results emphasize that crossover may be essentially completely eliminated in some cases, enabling for greatly improved operational viability.

2D nanomaterial↗
NASA NTRS1992

ASpect: A new spectrum and line analysis package for IRAF

We examined several publicly available spectral analysis software packages looking for one with enough functionality and versatility to meet the analysis needs of astronomers during the next decade. None of those examined can satisfactorily support the wide variety of panchromatic science programs that are now becoming possible. Furthermore, we concluded that none of these packages can be simply modified to include critical functions because of their original (limited) designs. During the next two years we will write a new spectral analysis package, ASpect, that will incorporate the latest analysis techniques for astronomical spectra in all wavelength domains. The ASpect package has several functional requirements. It must operate on spectra from a wide variety of ground-based and space-based instruments spanning wavelengths from radio to gamma rays. It must accommodate non-linear dispersion relations. It must provide a variety of functions, individually or in combination, with which to fit spectral features and the continuum. It is vitally important that known bad data be masked and that, uncertainties be propagated throughout the calculations in order for astronomers to evaluate the reliability of results. Finally, this new package must provide a powerful, intuitive graphical user interface to handle the burden of data input/output (I/O), on-line 'help,' selection of relevant features for analysis, plotting and graphical interaction, and data base management--all in a comprehensible environment. We anticipate that ASpect will take the form of an external package in IRAF (such as the NOAO and STSDAS packages) and will be layered upon the IRAF virtual Operating System to make it available on as many platforms as possible, while making it resistant to changes in operating systems and compilers. Our choice of IRAF is motivated by its portability, its wide use within the astronomical community, and its rich set of existing user applications.

Hulbert, S. J.↗
DOE OSTI2022

The influence of nitrogen and nitrides on the structure and properties of proton irradiated ferritic/martensitic steel

The 12Cr1MoWV (wt%) ferritic/martensitic steel HT9 is a candidate material for fuel cladding in advanced nuclear reactors, such as the Versatile Test Reactor currently under development. As such, understanding the relationship between microstructure and mechanical properties in the context of irradiation environments for these steels is critical. N content, and more specifically interstitial N, has been hypothesized to be detrimental to irradiated properties at lower temperatures (less than 0.3T m ) to a total of 6 dpa; however, in this work at a dose of 1 dpa the irradiated microstructure was improved with added N, leading to less irradiation hardening. Three variants of HT9 were irradiated with 1.5 MeV protons to a dose of 1 dpa at 300°C. The HT9 variants included Low (10 ppm), Mid (190 ppm), and High (440 ppm) N alloys that were otherwise nearly identical. Changing the N content had a variety of effects on the irradiated defect structures. As N content increased, the average dislocation loop diameter decreased, while the number density of loops increased. Additionally, extensive Ni clustering was observed on dislocations and interfaces. The Mid and High N specimens exhibited significantly less hardening (ΔHV≃100) relative to the Low N specimen (ΔHV≃160). The decrease in hardening is attributed to vanadium carbonitride acting as a sink for Ni clusters that would otherwise form on dislocations. Under the irradiation conditions used, these results suggest increasing the N content in HT9 may have a desirable effect on the irradiated structure and properties at the dose studied, as well as the swelling resistance at higher doses. In other words, N content appears to be a powerful tool for tailoring the self-interstitial atom cluster mobility in F/M steels for different temperature and dose applications.

36 MATERIALS SCIENCE↗