Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heterogenize”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Quantifying the chemical, electrochemical heterogeneity and spatial distribution of (poly) sulfide species using Operando SANS

In-situ and operando measurements are done to gain a better understanding of the precipitation mechanisms during charge and discharge in lithium sulfur batteries. A carbon felt networked with microfibers consisting of pores, 2 nm and smaller, is used as a freestanding sulfur host. Three different methods of sulfur infiltration are explored in order to determine the best one to fill most of the pores. It was identified to be a melt infiltration method in a vacuum oven, where the pores including the ultra-micropores, are successfully filled. In-situ electrochemical impedance spectroscopy measurements show a solid product formation occurring at the sulfur cathode, both during the high voltage plateau and at the end of discharge. In a 3-electrode EIS measurement, a similar solid product formation on the Li counter electrode due to its reaction with polysulfides is also observed. Operando small angle neutron scattering measurements show the solid product formation, in the carbon, both near the beginning and at the end of discharge, confirming the precipitation data via contrast changes as a function of charge and discharge. It is shown that Li 2 S precipitates in the pores at the beginning and the end of discharge, whereas S8 precipitates on the surface of the carbon felt. Finally, this lithium sulfur system shows both the quasi-solid-state and the solid-liquid-solid reactions in a typical ethereal electrolyte solution with a two-plateau discharge profile.

25 ENERGY STORAGE↗
DOE OSTI2025

Attribution of heterogeneous stress distributions in low-grain polycrystals under conditions leading to damage

In high-purity polycrystalline metallic materials, voids tend to favor grain boundaries as nucleation sites due to the elevated stress states produced by granular interactions and the weakened grain boundary from the relative atomic disorder. To quantify the key factors of this elevated stress state, simple compression of a small multi-grain cylinder of body-centered cubic tantalum was simulated using a single crystal plasticity model that incorporates non-Schmid effects. Four increasingly complex synthetic microstructures were created to tractably incorporate grain boundary interactions, and a statistically significant number of combinations were performed by varying the initial crystallographic orientations of the microstructure. Most of these simulations produce the maximum von Mises stress on a grain boundary and less frequently at the multi-grain junctions. To build a statistical model for the maximum von Mises stress at the grain boundary, physically based features that could contribute to the elevated stress state were selected. Then, a learning algorithm based on information theory was used to identify which of these features contributed the most information to the data set. The identified features include a grain’s propensity to accommodate both elastic and plastic deformations and their directional components. The misalignment of the direction of each grain’s mechanical response was found to be strongly correlated to the magnitude of the stress near the grain boundary. For all of the synthetic microstructures, the statistical models produce a residual distribution that is nearly Gaussian with a variance of, at most, 10% of the prior distribution. The successful performance of the statistical model implies the correct identification of the physical features that cause severe stress localization in polycrystalline materials. The statistical models constructed here can be used to formulate a physically motivated void nucleation model which is sensitive to a microstructure’s propensity to produce elevated stress states. As a result, these statistical models also enable the design of material microstructures, in which the crystallographic orientation is chosen to resist void nucleation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heterogeneous Diels–Alder tandem catalysis for converting cellulose and polyethylene into BTX

Producing biomass-derived aromatic hydrocarbons via controllable Diels–Alder reactions is a promising approach to recover energy and chemicals from waste streams. A tandem Diels–Alder catalysis consisting of SAPO-34 and Fe/HZSM-5 (stacked catalysis or mixed catalysis) was evaluated for thermochemical conversion of cellulose and polyethylene blends into benzene, toluene, and xylenes (BTX). Aromatization catalyst type significantly affected the activity of tandem catalysis, and the BTX obtained from the HZSM-5 stacked catalysis was ~2.3 times higher than that of the USY stacked one. An introduction of Fe active promoters into HZSM-5 increased the Lewis to Brønsted acid sites molar ratio (L/B) from 0.4 to 4.1. The comparison between Fe/HZSM-5 stacked catalysis and parent HZSM-5 single catalysis indicated that the former was more effective for BTX production, obtaining a nearly two-fold increase in yield with a high selectivity of 82.8%. A close proximity between Fe/HZSM-5 and SAPO-34 in the mixed catalysis increased the BTX enhancement to 1.8. A synergistic effect was provided by the coordination of Lewis and Brønsted acid sites in the Fe/HZSM-5 mixed catalysts for facilitating BTX generation, achieving a maximum of 25.9% at a Fe/HZSM-5 to SAPO-34 mass ratio of 1:1 with a theoretical L/B of 7.2. Finally, this work provides a sustainable strategy to produce biomass-derived aromatic hydrocarbons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗