Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generative diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Investigations of coherent anti-Stokes Raman spectroscopy /CARS/ for combustion diagnostics

Investigations of coherent anti-Stokes Raman spectroscopy (CARS) in a variety of flames are presented. Thermometry has received the primary emphasis in these studies, but species spectral and sensitivity studies will also be described. CARS is generated by mixing a 10 pps, frequency-doubled neodymium 'pump' laser with a spectrally broadband, laser-pumped, Stokes-shifted dye laser. This approach obviates the requirement to frequency scan the dye laser and generates the entire CARS spectrum with each pulse permitting, in principle, instantaneous measurements of medium properties. CARS spectra of N2, CO, O2, H2O, CO2 and CH4 in flames will be presented. In general these spectra exhibit very good agreement with computer synthesized spectra and permit measurements of temperature and species concentration. To illustrate the applicability of CARS to practical combustion diagnostics, CARS signatures from N2 have been employed to map the temperature field throughout a small, luminous, highly sooting propane diffusion flame

Eckbreth, A. C.↗

An Improved Neutron Transport Algorithm for Space Radiation

A low-energy neutron transport algorithm for use in space radiation protection is developed. The algorithm is based upon a multigroup analysis of the straight-ahead Boltzmann equation by using a mean value theorem for integrals. This analysis is accomplished by solving a realistic but simplified neutron transport test problem. The test problem is analyzed by using numerical and analytical procedures to obtain an accurate solution within specified error bounds. Results from the test problem are then used for determining mean values associated with rescattering terms that are associated with a multigroup solution of the straight-ahead Boltzmann equation. The algorithm is then coupled to the Langley HZETRN code through the evaporation source term. Evaluation of the neutron fluence generated by the solar particle event of February 23, 1956, for a water and an aluminum-water shield-target configuration is then compared with LAHET and MCNPX Monte Carlo code calculations for the same shield-target configuration. The algorithm developed showed a great improvement in results over the unmodified HZETRN solution. In addition, a two-directional solution of the evaporation source showed even further improvement of the fluence near the front of the water target where diffusion from the front surface is important.

Heinbockel, John H.↗

An Overview of Inter-comparison Methodologies for Terra and Aqua MODIS Calibration

With increasing efforts on data fusion and long-term climate data records (CDR) using observations made by multiple sensors, on the same or different platforms, their cross-calibration and validation work has become more and more important. The uncertainties of the climate models and data records depend not only on the calibration quality of individual sensors but also on their calibration consistency. This paper provides an overview of methodologies used by the MODIS Characterization Support Team (MCST) at NASA GSFC for the inter-comparison studies of Terra and Aqua MODIS on-orbit calibration. Each MODIS was built with a set of onboard calibrators (OBC) that include a blackbody (BB), a solar diffuser (SD), and a solar diffuser stability monitor (SDSM). The BB is primarily used for the thermal emissive bands (TEB) calibration and the SD/SDSM system for the reflective solar bands (RSB) calibration. Although the-instrument design and calibration approach are nearly identical for both Terra and Aqua MODIS and they all went through an extensive and similar pre-launch calibration and characterization process, still their on-orbit calibration consistency needs to be carefully examined and validated as many science products have been generated from observations made by both instruments. Methodologies discussed in this paper include inter-comparison studies using the Moon, a third sensor, and ground targets. Our results show that Terra and Aqua reflective solar bands and thermal emissive bands have been calibrated consistently with excellent long-term stabilities. For the 11 and 12 micrometers sea surface temperature (SST) bands, the calibration difference of Terra and Aqua MODIS is less than 0.2K.

Xiong, X.↗

Polycyclic Aromatic Hydrocarbons

Carbonaceous materials play an important role in space. Polycyclic Aromatic Hydrocarbons (PAHs) are a ubiquitous component of the carbonaceous materials. PAHs are the best-known candidates to account for the IR emission bands. They are also thought to be among the carriers of the diffuse interstellar absorption bands (DIBs). PAH ionization states reflect the ionization balance of the medium while PAH size, composition, and structure reflect the energetic and chemical history of the medium. A major challenge is to reproduce in the laboratory the physical conditions that exist in the emission and absorption interstellar zones. The harsh physical conditions of the ISM -low temperature, collisionless, strong UV radiation fields- are simulated in the laboratory by associating a molecular beam with an ionizing discharge to generate a cold plasma expansion. PAH ions and radicals are formed from the neutral precursors in an isolated environment at low temperature and probed with high-sensitivity cavity ringdown spectroscopy in the NUV-NIR range. Carbon nanoparticles are also formed during the short residence time of the precursors in the plasma and are characterized with time-offlight mass spectrometry. These experiments provide unique information on the spectra of large carbonaceous molecules and ions in the gas phase that can now be directly compared to interstellar and circumstellar observations (IR emission bands, DIBs, extinction curve). These findings also hold great potential for understanding the formation process of interstellar carbonaceous grains. We will review recent progress in the experimental and theoretical studies of PAHs, compare the laboratory data with astronomical observations and discuss the global implications.

Salama, Farid↗

The Past and Future of AstroPAH Research and the Diffuse Interstellar Bands

Here, we present a critical assessment of the PAHs as DIB Carriers and discuss the progress and the advances that have been achieved so far through a series of complementary studies involving astronomical observations of DIBs, laboratory simulation of interstellar analogs for PAHs (neutrals and ions), space exposure experiments of PAHs, theoretical calculations of PAH spectra and the modeling of diffuse and translucent interstellar clouds. We will discuss what we have learned from these complementary studies, the constraints that can be derived from these studies for the PAHs as DIB carriers and the future studies that are required to address the open questions. These involve extending the laboratory and astronomical PAH-DIB studies from the NUV-Visible range into the NIR and MIR domains where DIBs have also been observed and developing tools in the laboratory to help generate more complex, PAH-related species for comparison with astronomical data. For the laboratory part, we will present the COSmIC facility at NASA-Ames that provides experimental conditions that closely mimic the interstellar conditions and helps address these issues. The comparison of astronomical data with laboratory data measured under realistic conditions is the only way to derive clear and unambiguous conclusions regarding the expected abundances for PAHs of various sizes and charge states in interstellar environments. From the observational aspect we will explore the new opportunities offered by JWST to connect the DIBs to MIR PAH emission and to search for NIR DIBs that may trace the presence of PAHs.

Salama, Farid↗

SIBatt-3D: In-Space/On-Surface 3D Printing of Sodium Ion Batteries from ISRU Materials

Constructed more than 20 years ago, the International Space Station’s primary power system originally used nickel-hydrogen batteries with a lifetime of 6.5 years, until NASA began the process of replacing them in 2016 with lithium-ion batteries with a lifetime of 10 years. The demanding and costly process was accomplished after four flights of the Japanese H-II Transfer Vehicle cargo spacecraft (with a cost of about $10,000 per pound of payload), and 13 different astronauts conducting 14 spacewalks. Besides utilization in the ISS, rechargeable batteries are present in many space applications: they are installed in exploration robots, life support systems and in portable communication devices, to mention some. In this context, this project is focused on the in-space manufacturing of shape-conformable batteries using in-situ resources, and aims to address the NASA’s gaps related to the development of next generation of energy storage devices (TX03), as well as in-space manufacturing and in-situ resource utilization (TX07). The proposed work also tackles the HEOMD’s objectives targeting the in-space additive manufacturing (AM) from Lunar/Martian materials (regolith as AM feedstock) to reinvigorate America’s Human Space Exploration Program (SPD-1). This project is in direct alignment with the STMD’s objectives to demonstrate in-space autonomous manufacturing and assembly of complete systems by 2030, and to enable humans to live and explore in space and on planetary surfaces by 2040 thanks to in-space habitation, infrastructure development and in-situ resource utilization (ST1 and ST5). Manufacturing of shape conformable batteries directly in-space and using in-situ resources would also contribute to reducing the payload weight and volume (TX12) for future missions, thus reducing risk for long term Mars missions where rapid resupply is logistically infeasible. Nowadays, commercial batteries consist of stacked two-dimensional (2D) sheets, which are only manufactured in restricted geometries (cylindrical and coin cell). Evolving from conventional 2D, complex 3D battery architectures have been proven to increase the electrochemical active surface area and ion diffusion path, leading to improved areal energy density and power performance. This tendency was illustrated in our recent in-depth modeling studies by simulating a classical Ragone plot exhibiting the energy-power relationship. Our team demonstrated through modeling that a complex gyroidal 3D printed battery architecture exhibits significantly improved power performances (>150% at the current density of 6C; full discharge in 10 minutes) in comparison to a traditional 3D printed planar geometry. Motivated by these results and as the fabrication of intricate 3D battery design is only possible experimentally thanks to the geometric freedom offered by additive manufacturing (AM), our team has already initiated leveraging thermoplastic material extrusion at the laboratory scale. While 3D printing of batteries is relatively recent (2013), it has witnessed a growing interest during the last recent years, as next-generation shape-conformable 3D batteries can be co-designed with the system. Consequently, dead-volume and mass brought from Earth are minimized, in addition to improved battery performance, in alignment with the aforementioned NASA’s objectives. Further, while this project is specifically dedicated to batteries, it lends itself towards the maturation of in-space manufacturing via 3D printing using in-situ resources, stated in HEOMD and STMD goals.

In-Space Manufacturing↗

Two-dimensional radiative equilibrium of a gray medium in a plane layer bounded by gray nonisothermal walls

Radiative equilibrium temperature and surface heat flux distributions are calculated for an absorbing-emitting gray medium in an infinite plane layer bounded by gray diffuse walls with arbitrary temperature distributions. Superposition is used to obtain the solution for the differential approximation, which yields good accuracy for the optically thick medium. To also obtain accurate results for optically thin and intermediate regimes, the differential approximation is subsequently improved by a number of geometrical parameters, which are derived from the exact expression for the intensity. As an example, the case of constant temperature at the upper wall and a temperature step at the lower wall without heat generation in the medium is presented. Comparison with other available results shows excellent agreement.

Modest, M. F.↗

Formed platelet combustor liner construction feasibility, phase A

Environments generated in high pressure liquid rocket engines impose severe requirements on regeneratively cooled combustor liners. Liners fabricated for use in high chamber pressures using conventional processes suffer from limitations that can impair operational cycle life and can adversely affect wall compatibility. Chamber liners fabricated using formed platelet technology provide an alternative to conventional regeneratively cooled liners (an alternative that has many attractive benefits). A formed platelet liner is made from a stacked assembly of platelets with channel features. The assembly is diffusion bonded into a flat panel and then three-dimensionally formed into a section of a chamber. Platelet technology permits the liner to have very precisely controlled and thin hot gas walls and therefore increased heat transfer efficiency. Further cooling efficiencies can be obtained through enhanced design flexibility. These advantages translate into increased cycle life and enhanced wall compatibility. The increased heat transfer efficiency can alternately be used to increase engine performance or turbopump life as a result of pressure drop reductions within the regeneratively cooled liner. Other benefits can be obtained by varying the materials of construction within the platelet liner to enhance material compatibility with operating environment or with adjoining components. Manufacturing cost savings are an additional benefit of a formed platelet liner. This is because of reduced touch labor and reduced schedule when compared to conventional methods of manufacture. The formed platelet technology is not only compatible with current state-of-the art combustion chamber structural support and manifolding schemes, it is also an enabling technology that allows the use of other high performance and potentially low cost methods of construction for the entire combustion chamber assembly. The contract under which this report is submitted contains three phases: (1) phase A - feasibility study and technology development; (2) phase B - sub-scale fabrication feasibility; and (3) phase C - large scale fabrication validation. This report covers the Phase A activities, which began in December of 1988.

Hayes, W. A.↗

A Computational Fluid Dynamic and Heat Transfer Model for Gaseous Core and Gas Cooled Space Power and Propulsion Reactors

A computational model based on the axisymmetric, thin-layer Navier-Stokes equations is developed to predict the convective, radiation and conductive heat transfer in high temperature space nuclear reactors. An implicit-explicit, finite volume, MacCormack method in conjunction with the Gauss-Seidel line iteration procedure is utilized to solve the thermal and fluid governing equations. Simulation of coolant and propellant flows in these reactors involves the subsonic and supersonic flows of hydrogen, helium and uranium tetrafluoride under variable boundary conditions. An enthalpy-rebalancing scheme is developed and implemented to enhance and accelerate the rate of convergence when a wall heat flux boundary condition is used. The model also incorporated the Baldwin and Lomax two-layer algebraic turbulence scheme for the calculation of the turbulent kinetic energy and eddy diffusivity of energy. The Rosseland diffusion approximation is used to simulate the radiative energy transfer in the optically thick environment of gas core reactors. The computational model is benchmarked with experimental data on flow separation angle and drag force acting on a suspended sphere in a cylindrical tube. The heat transfer is validated by comparing the computed results with the standard heat transfer correlations predictions. The model is used to simulate flow and heat transfer under a variety of design conditions. The effect of internal heat generation on the heat transfer in the gas core reactors is examined for a variety of power densities, 100 W/cc, 500 W/cc and 1000 W/cc. The maximum temperature, corresponding with the heat generation rates, are 2150 K, 2750 K and 3550 K, respectively. This analysis shows that the maximum temperature is strongly dependent on the value of heat generation rate. It also indicates that a heat generation rate higher than 1000 W/cc is necessary to maintain the gas temperature at about 3500 K, which is typical design temperature required to achieve high efficiency in the gas core reactors. The model is also used to predict the convective and radiation heat fluxes for the gas core reactors. The maximum value of heat flux occurs at the exit of the reactor core. Radiation heat flux increases with higher wall temperature. This behavior is due to the fact that the radiative heat flux is strongly dependent on wall temperature. This study also found that at temperature close to 3500 K the radiative heat flux is comparable with the convective heat flux in a uranium fluoride failed gas core reactor.

Anghaie, S.↗

Polarimetric calibration of the Multi-Angle Imager for Aerosols (MAIA)

NASA’s Multi-Angle Imager for Aerosols (MAIA) mission, under development at the Jet Propulsion Laboratory, is designed to study the adverse health effects of different types of particulate air pollution. Planned for launch in 2023 for a 3-year mission, the MAIA satellite instrument will focus on a selected set of metropolitan target areas, where air quality monitors and health data are available. Aerosol concentration and speciation are inferred from multi-angle measurements of backscattered sunlight in 14 spectral bands from 350-2200 nm, with bands near 442, 645 and 1040 nm measuring the degree (DoLP) and angle of linear polarization (AoLP) in addition to radiance. The pushbroom camera has a ~240-km cross-track field of view with a nadir resolution of ~200 m, and is mounted onto a biaxial gimbal to provide along-track view angles within ±60°, to extend the field of regard to ±48°, and to view the instrument’s onboard calibrator (OBC) and dark target. The OBC consists of a sunlit transmissive diffuser, followed by 12 polarizers at different orientations. MAIA’s polarimetry is implemented using miniature wire grid polarizers on the focal plane array, and dual photoelastic modulators (PEMs) and achromatic quarter-wave plates to rapidly rotate the polarization. The resulting ~26-Hz intensity modulation encodes the linearly polarized and total radiance in each pixel, leaving the DoLP and AoLP insensitive to gain calibration. We report on the polarimetric calibration of the MAIA camera using a vacuum-compatible polarization state generator, consisting of a 1600W Xenon lamp, 12-inch integrating sphere, and rotating high-extinction polarizer. Mueller-matrix-based calibration coefficients for each detector pixel are derived from measurements at multiple polarizer angles, and are used to correct the measurements for instrumental polarization aberrations. Prior to flight, the calibrated MAIA camera is panned across the OBC to characterize its output, using uniform illumination with an irradiance similar to the Sun.

Werne, Thomas↗

Distortion in a full-scale bicone inlet with internal focused compression and 45 percent internal contraction

The distortion characteristics were investigated at the subsonic diffuser exit of a full-scale, Mach 2.5, axisymmetric, mixed compression inlet. Performance and steady-state distortion characteristics were obtained at zero and maximum angle of attack and during an inlet unstart-restart sequence. For the configuration with no cowl bleed, steady-state distortion P(max)P(min)P(bar) ranged from 0.10 for critical inlet operation at 0 deg angle-of-attack to 0.306 for supercritical inlet operation at 6.84 deg angle-of-attack. Vortex generators provided a 50 percent reduction in steady-state distortion for critical operation. Bleed has a smaller effect on steady-stated distortion.

Wasserbauer, J. F.↗

Transport processes in the upper atmosphere

Studies of transport mechanisms in the upper atmosphere (diffusion, turbulence, large-scale circulation) are reviewed. A normally turbulent state of the lower thermosphere is inferred from direct observations of tracers and from thermal and composition structure. Viscous dissipation in the thermosphere and energy dissipation in turbulence working against buoyancy are discussed in relation to a critical Richardson number for initiation of turbulence (0.25, as in the stratosphere). But the usefulness of the Richardson criterion is limited when static stability is low, as is the case when strong shear-generated turbulence prevails.

Johnson, F. S.↗

Time-dependent simulation of oblique MHD cosmic-ray shocks using the two-fluid model

Using a new, second-order accurate numerical method we present dynamical simulations of oblique MHD cosmic-ray (CR)-modified plane shock evolution. Most of the calculations are done with a two-fluid model for diffusive shock acceleration, but we provide also comparisons between a typical shock computed that way against calculations carried out using the more complete, momentum-dependent, diffusion-advection equation. We also illustrate a test showing that these simulations evolve to dynamical equilibria consistent with previously published steady state analytic calculations for such shocks. In order to improve understanding of the dynamical role of magnetic fields in shocks modified by CR pressure we have explored for time asymptotic states the parameter space of upstream fast mode Mach number, M(sub f), and plasma beta. We compile the results into maps of dynamical steady state CR acceleration efficiency, epsilon(sub c). We have run simulations using constant, and nonisotropic, obliquity (and hence spatially) dependent forms of the diffusion coefficient kappa. Comparison of the results shows that while the final steady states achieved are the same in each case, the history of CR-MHD shocks can be strongly modified by variations in kappa and, therefore, in the acceleration timescale. Also, the coupling of CR and MHD in low beta, oblique shocks substantially influences the transient density spike that forms in strongly CR-modified shocks. We find that inside the density spike a MHD slow mode wave can be generated that eventually steepens into a shock. A strong layer develops within the density spike, driven by MHD stresses. We conjecture that currents in the shear layer could, in nonplanar flows, results in enhanced particle accretion through drift acceleration.

Frank, Adam↗

Acoustic Testing of Flight Hardware Using Loudspeakers: How Much do We Know About This Method of Testing?

Loudspeakers have been used for acoustic qualification of spacecrafts, reflectors, solar panels, and other acoustically responsive structures for more than a decade. Even though a lot of hardware has been acoustic tested using this method, the nature of the acoustic field generated by controlling an ensemble of speakers with and without the hardware in the test volume has not been thoroughly investigated. Limited measurements from some of the recent speaker tests used to qualify flight hardware have indicated significant spatial variation of the acoustic field within the test volume. Also structural responses have been reported to differ when similar tests were performed using reverberant chambers. Unlike the reverberant chamber acoustic test, for which the acoustic field in most chambers is known to be diffuse except below several tens of Hz where acoustic standing waves and large spatial variations exist, the characteristics of the acoustic field within the speaker test volume has not been quantified. It has only been recently that a detailed acoustic field characterization of speaker testing has been made at Jet Propulsion Laboratory (JPL) with involvement of various organizations. To address the impact of non-uniform acoustic field on structures, a series of acoustic tests were performed using a flat panel and a 3-ft cylinder exposed to the field controlled by speakers and repeated in a reverberant chamber. The analysis of the data from this exercise reveals that there are significant differences both in the acoustic field and in the structural responses. In this paper the differences between the two methods are reviewed in some detail and the over- or under-testing of articles that could pose un-anticipated structural and flight qualification issues are discussed. A framework for discussing the validity of the speaker acoustic testing method with the current control system and a path forward for improving it will be provided.

Acoustics↗

Vortex interactions and decay in aircraft wakes

The dynamic interactions of aircraft wake vortices are investigated using both inviscid and viscous models. The phenomenon of vortex merging resulting in the rapid aging of a vortex wake is examined in detail. It is shown that the redistribution of vorticity from convection and diffusion during merging is a mechanism effective in reducing the hazard of a wake. Inviscid computations show that the merging phenomenon may be sensitive to small changes in spanwise load distribution and that the fuselage vortex shed from the wing-fuselage junction can play a significant role in promoting merging of wing-tip and flap vortices. Vortex-wake-merging computations using a second-order closure model of turbulent transport indicate that a low-hazard wake occurs when the generating aircraft flap and wing-tip vortices of the same strength and sign. This optimum is achieved when the flap vortex is located outboard approximately 40% of the distance to the tip vortex.

Bilanin, A. J.↗

Residual fields from extinct dynamos

The generation of magnetic fields in convective zones of declining vigor and/or thickness is considered, the goal being to explain the magnetic fields observed in A-stars. The investigation is restricted to kinematical dynamos in order to show some of the many possibilities, which depend on the assumed conditions of decline of the convection. The examples illustrate the quantitative detail required to describe the convection in order to extract any firm conclusions concerning specific stars. The first example treats the basic problem of diffusion from a layer of declining thickness. The second has a buoyant rise added to the field in the layer. The third deals with plane dynamo waves in a region with declining eddy diffusivity, dynamo coefficient, and large-scale shear. It is noted that the dynamo number may increase or decrease with declining convection, with an increase expected if the large-scale shear does not decline as rapidly as the eddy diffusivity. It is shown that one of the components of the field may increase without bound even when the dynamo number declines to zero.

Parker, E. N.↗

Interaction of an oscillating vortex with a turbulent boundary layer

The effects on mean flow and turbulence caused by meander of a vortex embedded in a two-dimensional boundary layer were investigated experimentally by driving a forced lateral oscillation of the vortex generator. Upstream, the vorticity contours without forcing were found to be round. The forced vortex generator oscillation caused a flattening of the time-averaged vorticity contours and changes in some of the Reynolds stresses. The results indicate that the unforced vortex did not meander significantly upstream, and that the effects of meander can be understood qualitatively from production of Reynolds stresses by the forced motion acting with the exiting three-dimensional velocity field. Farther downstream, the observed differences in the mean vorticity and Reynolds stresses caused by forcing were smaller, mainly because the vortex was substantially diffused at this station, resulting in smaller mean velocity gradients.

Westphal, Russell V.↗

Mass transfer across combustion gas thermal boundary layers - Power production and materials processing implications

The effects of Soret diffusion (for vapors) and thermophoresis (for particles) are illustrated using recent optical experiments and boundary layer computations. Mass transfer rate augmentations of up to a factor of 1000 were observed and predicted for submicron-particle capture by cooled solid surfaces, while mass transfer suppressions of more than 10 to the -10th-fold were predicted for 'overheated' surfaces. It is noted that the results obtained are of interest in connection with such technological applications as fly-ash capture in power generation equipment and glass droplet deposition in optical-waveguide manufacture.

Rosner, D. E.↗