SEARCH · Engineering Papers

Results for “fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Theory of fracture mechanics based upon plasticity

A theory of fracture mechanics is formulated on the foundation of continuum mechanics. Fracture surface is introduced as an unknown quantity and is incorporated into boundary and initial conditions. Surface energy is included in the global form of energy conservation law and the dissipative mechanism is formulated into constitutive equations which indicate the thermodynamic irreversibility and the irreversibility of fracture process as well.

Lee, J. D.↗

NASA NTRS1977

Techniques for increasing boron fiber fracture strain

Improvement in the strain-to-failure of chemical-vapor-deposition boron fibers is shown possible by contracting the tungsten boride core region and its inherent flaws. Results of three methods are presented in which etching and thermal-processing techniques were employed to achieve core flaw contraction by internal stresses available in the boron sheath. After commercially and treatment-induced surface flaws were removed from 203-micron (8-mil) fibers, the core flaw was observed to be essentially the only source of fiber fracture. Thus, fiber strain-to-failure was found to improve by an amount equal to the treatment-induced contraction on the core flaw. To date, average fracture strains and stresses greater than 1.4% and 5.5 GN/sq m (800 ksi), respectively, have been achieved. Commercial feasibility considerations suggest as the most cost-effective technique that method in which as-produced fibers are given a rapid heat treatment above 700 C. Preliminary results concerning the contraction kinetics and fracture behavior observed with this technique are presented and discussed for both high-vacuum and argon-gas heat-treatment environments.

Dicarlo, J. A.↗

NASA NTRS1978

Delayed fracture of silicon: Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

Bar specimens were cut from ingots of single crystal silicon, and acid etched prior to testing. Artificial surface flaws were introduced in specimens by indentation with a Knoop hardness tester. The specimens were loaded in four-point bending to 95 percent of the nominal fracture stress, while keeping the surface area, containing the flaw, wet with test liquids. No evidence of delayed fracture, and, therefore stress corrosion, of single crystal silicon was observed for liquid environments including water, acetone, and aqueous solutions of NaCl, NH4OH, and HNO3, when tested with a flaw parallel to a (110) surface. The fracture toughness was calculated.

Chen, T. J.↗

NASA NTRS1978

Recent developments in analysis of crack propagation and fracture of practical materials

The limitations of linear elastic fracture mechanics in aircraft design and in the study of fatigue crack propagation in aircraft structures are discussed. NASA-Langley research to extend the capabilities of fracture mechanics to predict the maximum load that can be carried by a cracked part and to deal with aircraft design problems are reported. Achievements include: (1) improved stress intensity solutions for laboratory specimens; (2) fracture criterion for practical materials; (3) crack propagation predictions that account for mean stress and high maximum stress effects; (4) crack propagation predictions for variable amplitude loading; and (5) the prediction of crack growth and residual stress in built-up structural assemblies. These capabilities are incorporated into a first generation computerized analysis that allows for damage tolerance and tradeoffs with other disciplines to produce efficient designs that meet current airworthiness requirements.

Hardrath, H. F.↗

NASA NTRS1977

Friction, deformation and fracture of single-crystal silicon carbide

An investigation was conducted to determine the nature of the deformation and fracture of silicon carbide and its effects on friction properties. Friction experiments were conducted with hemispherical and conical diamond riders sliding on the basal plane of silicon carbide. The results indicate that, when deformation is primarily elastic, the friction does not depend on crystallographic orientation and there is no detectable fracture or cracking. When, however, plastic deformation occurs, silicon carbide exhibits anisotropic friction and deformation behavior. Surface fracture crack patterns surrounding wear tracks are observed to be of three types. The crack-geometries of two types are generally independent of orientation, the third crack, however, depends on the orientation. All surface cracks extend into subsurface.

Miyoshi, K.↗

NASA NTRS1978

Investigation of the fracture mechanism of Ti-5Al-2.5Sn at cryogenic temperatures

Fractography and metallographic sectioning were used to investigate the influence of microstructure on the fracture mechanism and fracture toughness (KIC) of normal interstitial and extra low interstitial (ELI) Ti-5Al-25Sn at 20 K (-423 F) and 77 K (-320 F). Plates of each grade were mill annealed at 815 C followed by either air or furnace cooling. These variations in composition and cooling rate resulted in differences in the volume fraction and internal structure of the dispersed beta phase and in the ordering of the alpha matrix. The ELI alloys were tougher than the normal interstitial plates. KIC of the furnace-cooled ELI plate was 25% lower than that of the air-cooled ELI material. Variations in cooling rate had no influence of KIC of the normal interstitial alloys. Fractography showed that a large portion of the fracture surfaces were covered with elongated dimples. Metallographic sections of specimens deformed at 77 K showed that these features form at the intersections of slip bands or deformation twins with grain or twin boundaries. Ordering and higher interstitial levels increase the local strain in slip bands resulting in void nucleation at lower macroscopic strains and lower KIC values.

Van Stone, R. H.↗

NASA NTRS1977

A joint fracture toughness evaluation of hot-pressed beryllium

Fracture toughness tests at room temperature were made on three-point bend specimens cut from hot-pressed beryllium obtained from two suppliers. The test specimens had dimensions conforming to ASTM fracture toughness standard E399-72. A total of 42 specimens were machined from each batch of material. Six specimens from each batch were then distributed to seven independent laboratories for testing. The test data from the laboratories were collected and analyzed for differences between the laboratories and the two batches of material. It is concluded that ASTM 399-72 can be used as a valid test procedure for determining the fracture toughness of beryllium, providing that Kf(max) in fatigue cracking could be up to 80 percent of the K(0) value.

Conrad, H.↗

NASA NTRS1979

Anisotropic friction, deformation, and fracture of single-crystal silicon carbide at room temperature

Anisotropic friction, deformation, and fracture studies were conducted with /0001/, /10(-1)0/, and /11(-2)0/ silicon carbide surfaces in sliding contact with diamond. The experiments were conducted with loads of 0.1, 0.2, and 0.3 N at a sliding velocity of 3 mm/min in mineral oil or in dry argon at room temperature. The 1010 direction on the basal /0001/ plane exhibits the lowest coefficient of friction and the greatest resistance to abrasion for silicon carbide. Anisotropic friction and deformation of the /0001/, /10(-1)0/, and /11(-2)0/ silicon carbide surfaces are primarily controlled by the slip system /10(-1)0/ 11(-2)0. The anisotropic fracture during sliding on the basal plane is due to surface cracking along /10(-1)0/ and subsurface cracking along /0001/. The fracture during sliding on the /11(-2)0/ or /10(-1)0/ surfaces is due to surface cracking along /0001/ and /11(-2)0/ or /10(-1)-1 and to subsurface cracking along /10(-1)0/.

Miyoshi, K.↗

NASA NTRS1979

Fracture modes and acoustic emission of composite materials

Unidirectional fibrous composite material laminae are the construction material of a laminate. Four failure modes can occur in this material, and the identification of these modes is as important as the identification of onset of fracture. Acoustic emission (AE) pulses, generated by the change in the stress field resulting from cracking in a material, have a unique pattern of amplitude distribution that depends only on the mode of fracture and the type of material. By using a tapered double-cantilever beam as grips for the unidirectional lamina, a crack with a constant stress intensity factor was induced, thus eliminating the factor of the stress level. Placing the lamina in different directions relative to the grips imposed a different failure mode. By plotting the log of the relative number of AE pulses above some level versus the log of the relative level, a single constant coefficient can be measured for each material and mode of fracture. The AE energy is proportional to the energy released by the cracking; this proportionality depends on the medium where the AE waves have to travel, and not on the cracking mode.

Rotem, A.↗

NASA NTRS1979

On the equivalence between semiempirical fracture analyses and R-curves

The relationships between several semiempirical fracture analyses (Brockrath and Glassco, 1974; Newman, 1973; Kuhn, 1968; Orange, 1971; Feddersen, 1971) and the R-curve concept of fracture mechanics are examined. Some characteristics of the R-curve concept when applied to finite-width specimens are reviewed, and conditions for equivalence between a semiempirical analysis (SEFA) and an R-curve are derived. The relationship between R-curves and SEFAs is studied for a hypothetical material. It is shown that for each SEFA there is an equivalent R-curve, the magnitude and shape of which are determined by the SEFA formulation and parameters, and which predicts precisely the same relationship between fracture stress and original crack length. A given SEFA correlates residual strength data closely if its equivalent R-curve closely matches the actual R-curve of the material studied. The SEFA given by Newman is found to yield best results for the hypothetical case considered. Equivalent R-curves for real materials are developed using data from the literature.

Orange, T. W.↗

NASA NTRS1979

Fracture strength of silicon solar cells

A test program was developed to determine the nature and source of the flaw controlling the fracture of silicon solar cells and to provide information regarding the mechanical strength of cells. Significant changes in fracture strengths were found in seven selected in-process wafer-to-cell products from a manufacturer's production line. The fracture strength data were statistically analyzed and interpreted in light of the exterior flaw distribution of the samples.

Chen, C. P.↗

NASA NTRS1980

Performance of Chevron-notch short bar specimen in determining the fracture toughness of silicon nitride and aluminum oxide

Ease of preparation and testing are advantages unique to the chevron-notch specimen used for the determination of the plane strain fracture toughness of extremely brittle materials. During testing, a crack develops at the notch tip and extends stably as the load is increased. For a given specimen and notch configuration, maximum load always occurs at the same relative crack length independent of the material. Fracture toughness is determined from the maximum load with no need for crack length measurement. Chevron notch acuity is relatively unimportant since a crack is produced during specimen loading. In this paper, the authors use their previously determined stress intensity factor relationship for the chevron-notch short bar specimen to examine the performance of that specimen in determining the plane strain fracture toughness of silicon nitride and aluminum oxide.

Munz, D.↗

NASA NTRS1980

Fracture toughness of boron/aluminum laminates with various proportions of 0 deg and plus or minus 45 deg

The fracture toughness of boron/aluminum laminates was measured on sheet specimens containing central slits of various lengths that represent cracks. The specimens were loaded axially and had various widths. The sheets were made with five laminate orientation. Fracture toughness was calculated for each laminate orientation. Specimens began failing at the ends of the slit with what appeared to be tensile failures of fibers in the primary load carrying laminae. A general fracture toughness parameter independent of laminate orientation was derived on the basis of fiber failure in the principal load carrying laminae. The value of this parameter was proportional to the critical value of the stress intensity factor. The constant of proportionality depended only on the elastic constants of the laminates.

Poe, C. C., Jr.↗

NASA NTRS1980

A proposed standard round compact specimen for plane strain fracture toughness testing

A round, disk-shaped specimen is proposed as a standard test specimen for addition to ASTM Test for Plane-Strain Fracture Toughness of Metallic Materials (E 399-78A). The specimen is diametrically cracked, and loaded in the same way as the existing standard compact specimen. Tests and analyses were performed to verify that the proposed round compact specimen and associated stress intensity factor K solution are appropriate for a standard plane strain fracture toughness test. The use of the round compact specimen for other fracture tests is described.

Underwood, J. H.↗

NASA NTRS1980

Increased fracture toughness of graphite-epoxy composites through intermittent interlaminar bonding

The objective of this study was to increase the fracture toughness of multilayer continuous-filament graphite-epoxy composites. The method used is intermittent interlaminar bonding which can lead to a large increase in the fracture surface area. Intermittent bonding was achieved through introduction of thin perforated Mylar between the layers of the composite. For the optimum condition, fracture toughness was increased from about 100 kJ/sq m for untreated specimens to an average of about 500 kJ/sq m, while tensile strength dropped from 500 MPa to 400 MPa, and elastic modulus remained the same at about 75 GPa. An approximate analysis is presented to explain the improvement in toughness.

Jea, L.-C.↗

NASA NTRS1980

Effect of production processes on the fracture strength of silicon solar cells

Fracture of Czochralski silicon wafers during processing is an important factor in solar cell yield and cost. A fracture-mechanics test and analysis program was developed to evaluate fracture strength changes in the in-process wafer-to-cell processing at different stages on a manufacturer's production line. The strength data were described by Weibull statistical analysis and can be interpreted with the surface-flaw distribution of each of the process steps.

Chen, C. P.↗

NASA NTRS1981

Environmental effects on composite fracture behavior

An experimental program was carried out to investigate the effects of temperature and moisture on the damage development and fracture response of graphite/epoxy composites. Fracture response data were obtained for 20-ply laminates of different layup patterns for both room temperature and immediately after the application of a temperature transient causing the specimen to attain 150 C. It is found that elevated temperature degrades the notched strength of some laminates while not degrading others. The unnotched strength of all laminates tested at elevated temperatures was degraded. The effect of preloading on damage growth and moisture absorption, the effect of autoclave pressure during the laminate cure on fracture, and the variation of interlaminar shear properties with layup, moisture exposure, laminate material, and cure pressure are also discussed.

Porter, T. R.↗

NASA NTRS1981

Fracture mechanics of cellular glass

The fracture mechanics of cellular glasses (for the structural substrate of mirrored glass for solr concentrator reflecting panels) are discussed. Commercial and developmental cellular glasses were tested and analyzed using standard testing techniques and models developed from linear fracture mechanics. Two models describing the fracture behavior of these materials were developed. Slow crack growth behavior in cellular glass was found to be more complex than that encountered in dense glasses or ceramics. The crack velocity was found to be strongly dependent upon water vapor transport to the tip of the moving crack. The existence of a static fatigue limit was not conclusively established, however, it is speculated that slow crack growth behavior in Region 1 may be slower, by orders of magnitude, than that found in dense glasses.

Zwissler, J. G.↗