SEARCH · Engineering Papers

Results for “feature selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1961

A Satellite Borne Cadmium Sulfide Total Corpuscular Energy Detector

The properties of single crystals of cadmium sulfide as radiation detectors are described. It has been found possible to select crystals such that: (a) The ratio of increase of conductivity under irradiation to the rate of absorption of energy in the crystal is substantially independent of particle energy (over the examined ranges of 500 ev to 80 kev for electrons and 5 kev to 180 kev for protons) and of the magnitude of energy flux (over the range from.005 to 10 ergs/cm(sup 2 -sec); and (b) The above ration is substantially the same for protons, electrons, alpha particles, x-rays, and gamma-rays. For a driving voltage of 100 volts, typical crystal yield currents of 10(sup -7) to 10(sup- 6) amperes for each erg/cm(sup 2-sec) of energy absorbed by the crystal. The threshold of such crystal detectors (resulting from dark currents of the order of 10(sup 10 amp) is typically 10(sup -3) ergs/cm(sup 2- sec). For the selected crystals a response-temperature coefficient of -0.25% per degree centigrade is found for the temperature range -50 deg C to + 50 deg C. A description is given of a complete CdS total corpuscular energy detector for the study of geomagnetically trapped radiation by means of a satellite. The detector described has a dynamic range great than 10(sup 4), a solid angle of 10(exp -3) steradian, and a detection threshold of approximately 1 erg/cm(sup 2-sec-sterad). A similar detector employing a small magnet for the selective exclusion of electrons is also described. Noteworthy practical features of these detectors for satellite and space probe experiments are: (a) Use of bare crystals, without covering foils, in order to detect charged particles having energies as low as hundreds of electron volts. (b) Simplicity of electronic auxiliaries. (c) Compactness, lightweight and nechanical ruggedness. (d) Low electrical power requirements; and (e) Conversion of conduction current to the rate of a twostate relaxation oscillator in order to facilitate telemetric transmission of data. A pair of such detectors was flown as part of the s-46 satellite payload on March 23, 1960, but due to vehicular failure an orbit was not achieved and the operation of the CdS detectors was observed for only, six minutes of flight.

Freeman, John W.↗

NASA NTRS2018

Radioisotope Power Systems to Enable Extended Lunar Science and In-Situ Resource Utilization Missions

The Moon's surface environment offers a significant challenge for most space systems and, particularly, for power technologies. First, the Moon's rotational synodic period is 27.3 days long because it is tidally-locked with Earth and thus matches its orbital period. However, for a point on the lunar surface with respect to the Sun returning to the same position in the sky, called a synodic day, is 29.5 days or 708 hours. Therefore, a lunar day is 354 hours of sunlight and 354 hours of darkness. Equatorial diurnal temperatures range from about 400K at noon to 100K during the night. Within craters and permanently shadowed regions (PSRs) temperatures can be a constant 40K or below. Sunlight in the lunar polar regions can range from total darkness in deep polar craters and at higher elevations, potentially nearly continuous conditions are possible. However local topographical features such as outcrops or more distant mountains and ridges would obscure the Sun even in these extended sunlit areas and thus create intermittent shadowed periods depending on seasonally varying Sun angle and the obscuring topographical features. Thus, the power system technology that a mission selects becomes a critical trade.

radioisotope↗

NASA NTRSDate not supplied

Making & Breaking the Rules for DED Design

Design for Additive Manufacturing (DfAM) is widely used to describe design activities and guidelines employed in the creation of Additively Manufactured (AM) parts. Basic design rules for widely adopted processes like Powder Bed Fusion (PBF) are relatively understood including material performance, part size constraints, self-supporting angles, overhangs, wall thicknesses, and feature resolution. Complexity is often inherent with PBF using organically inspired solutions through generative design and topology optimization software to create designs that often cannot be realized via traditional manufacturing processes. The design rules for Directed Energy Deposition (DED) are less well known, and, in some cases, the lack of understanding is likely inhibiting broader application of the various DED processes. This presentation covers key design rules for DED fusion processes and elucidates opportunities like multi-material deposition and build approaches ranging from basic features to complex large-scale parts. Complementary to the opportunistic characteristics of DfAM for DED, Manufacture for AM (MfAM) encompasses the restrictive aspects of the manufacturing lifecycle with limitations due to bead width and wall thickness, self-supporting angles, surface texture, microstructural evolution, and residual stresses. AM enabled part design must always consider the entire value chain starting with incoming feedstock (e.g. plate, wire, or powder) and progressing through the printing process, post-processing (e.g. machining, inspection), and final system assembly. Key considerations, like the tradeoffs between feature resolution and build rate, for process and part selection and economic assessments will be discussed as DED is often traded against other AM processes. After highlighting typical DED design rules, we will also show how some of those rules can be broken via use cases and part designs that span the full spectrum of DED processes with examples of various DED part designs.

Additive Manufacturing↗

NASA NTRSDate not supplied

Microscopy Methods for Life Detection on Ocean Worlds

On Earth, light microscopy is commonly used in microbiology to identify organisms and observe their interactions with the environment; this makes it an attractive technique for in situ life detection methods on ocean worlds. As a standalone technique, brightfield microscopy, while able to provide important contextual information, has limited usefulness as a life detection technique because it is often challenging to differentiate between abiotic and biotic particles based solely on their size and shape, which may introduce risks of false positive or false negative interpretations. However, these risks can be reduced by combining brightfield microscopy with fluorescence microscopy to provide a method that correlate sample chemistry with sample morphology. In this work, we have used the Luminescence Imager for Exploration (LIfE), a brightfield and epifluorescence microscope with an integrated sample processing system (matured under the Concepts for Ocean worlds Life Detection Technology and Instrument Concepts of Europa Exploration programs) to develop methods that increase the fidelity of in situ microscopy life detection measurements through two main approaches. First, native fluorescence is excited in molecules that contain aromatic moieties such as proteins (using deep UV excitation), and energy carrying molecules and endogenous chromophores (using visible-light excitation), to correlate the location of these species with cell-like structural features (brightfield imaging). Second, fluorescent stains are used to selectively image cells and cell fragments by targeting proteins, lipids, and nucleic acids. We discuss the results of tests, obtained using ocean world analog samples, that have examined trades associated with implementing these methods autonomously in planetary missions, including the intrinsic properties of candidate fluorescence dyes and long-term storage and radiation stability.

Pavel E. Z. Klier↗

NASA NTRSDate not supplied

Microscopy Methods for Life Detection on Ocean Worlds

Pavel E Z Klier↗

DOE OSTI2024

A Generic and Multi-Functional Electromagnetic Transient Model for Grid-Following Inverter: Preprint

This article presents a generic and multi-functional electromagnetic transient (EMT) dynamic model of grid following (GFL) inverter-based resource (IBR) using the PSCAD TM software platform. The features of the developed model includes the flexibility in selecting various types and combinations of DC sources covering PV modules, battery modules, ideal DC source module, as well as flexibility in selecting either switched or averaged model of inverter. This model also covers exhaustive lists of controller logic covering open-loop/closed-loop PQ dispatch control, DC voltage and AC terminal voltage control along with the conventional current control designed in dq-domain, aB- domain and positive-negative sequence domain. Moreover, this model is equipped with the flexibility in selecting various types of current limiting schemes that includes saturation-based as well as latching-based current limiter, anti-windup protection. Moreover, the EMT model is agnostic to the MVA rating and is suitable for interfacing transmission systems by being complaint with the IEEE Std. 2800. The generality in the power circuits and the multi-functional options in operation and control of the developed EMT model makes it suitable for both academia and industry to study various power system aspects not limited to but such as fault behavior of GFL IBR and impacts on protection system, transient stability of a system interfaced with large number of GFL IBRs etc.

grid following inverter↗

DOE OSTI2022

AGR-2 irradiated TRISO particle IPyC/SiC interface analysis using FIB-SEM tomography

In this work, the morphology in the interface region between the inner pyrolytic carbon layer (IPyC) and silicon carbide (SiC) layers in tristructural-isotropic (TRISO) particle fuel from the AGR-2 irradiation experiment were studied using focused ion beam-scanning electron microscopy tomography. This work quantitatively described the interface and corresponding relevant metrics to understand how the microstructural features at the IPyC/SiC interface may influence actinide and fission product interactions with the SiC layer. Particles were selected with varied 110m Ag retention rates, and their volumes were reconstructed and analyzed for distributions of pores, fission product/actinide features, SiC, and IPyC. It was found that porosity accommodates fission products in the interface and SiC layers. The largest fission product/actinide precipitates were found in the interface region. This was also where the largest number fraction of fission products/actinides was found, consistent with SEM showing fission product/actinide pileup along selected areas of the interface region.

36 MATERIALS SCIENCE↗

NASA NTRS2002

QMI: Rising to the Space Station Design Challenge

The Quench Module Insert (QMI) materials processing furnace is being designed to operate for 8000 hours over four years on the International Space Station (ISS) as part of the first Materials Science Research Rack (MSRR-1) of the Materials Science Research Facility (MSRF). The Bridgman-type furnace is being built for the directional solidification processing of metals and alloys in the microgravity environment of space. Most notably it will be used for processing aluminum and related alloys. Designing for the space station environment presents intriguing design challenges in the form of a ten-year life requirement coupled with both limited opportunities for maintenance and resource constraints in the form of limited power and space. The long life requirement has driven the design of several features in the furnace, including the design of the heater core, the selection and placement of the thermocouples, overall performance monitoring, and the design of the chill block. The power and space limitations have been addressed through a compact furnace design using efficient vacuum insulation. Details on these design features, as well as development test performance results to date, are presented.

Carswell, W. E.↗

NASA NTRS1995

Site selection for Mars exobiology

The selection of sites on Mars that have a high priority for exobiological research is fundamental for planning future exploration. The most immediate need is to identify targets for high resolution orbital imaging during the Mars Observer and Mars '94/'96 missions that can be used to refined site priorities for surface exploration. We present an objective approach to site selection whereby individual sites are selected and scored, based on the presence of key geological features which indicate high priority environments. Prime sites are those that show evidence for the prolonged activity of liquid water and which have sedimentary deposits that are likely to have accumulated in environments favorable for life. High priority areas include fluvio-lacustrine (stream-fed lake systems), springs, and periglacial environments. Sites where mineralization may have occurred in the presence of organisms (e.g. springs) are given high priority in the search for a fossil record on Mars. A systematic review of Viking data for 83 sites in the Mars Landing Site Catalog (MLSC) resulted in the selection of 13 as being of exobiological interest. The descriptions of these sites were expanded to address exobiological concerns. An additional five sites were identified for inclusion in the second edition of the MLSC. We plan to broaden our site selection activities to include a systematic global reconnaissance of Mars using Viking data, and will continue to refine site priorities for exobiological research based on data from future missions in order to define strategies for surface exploration.

Farmer, J.↗

DOE OSTI2025

Integrative mapping reveals molecular features underlying the mechanism of nucleocytoplasmic transport

Nuclear pore complexes (NPCs) enable rapid, selective, and robust nucleocytoplasmic transport. To explain how transport emerges from the system components and their interactions, we used experimental data and theoretical information to construct an integrative Brownian dynamics model of transport through an NPC, coupled to a kinetic model of transport in the cell. The model recapitulates key aspects of transport for a wide range of molecular cargoes, including preribosomes and viral capsids. Our model quantifies how flexible phenylalanine-glycine (FG) repeat proteins create an entropic barrier to passive diffusion and how this barrier is selectively lowered in facilitated diffusion by the many transient interactions of nuclear transport receptors with the FG repeats. Selective transport is enhanced by “fuzzy” multivalent interactions, redundant FG repeat mass, coupling to the energy-dependent RanGTP concentration gradient, and exponential dependence of transport kinetics on the transport barrier. Our model will facilitate rational modulation of the NPC and its artificial mimics.

Raveh, Barak [School of Computer Science and Engin↗

NASA NTRS1977

Rationale for selection of a flight control system for lift cruise fan V/STOL aircraft

Various features of the lift cruise fan V/STOL concept are briefly reviewed. The ability to operate from small ships in adverse weather, low visibility, and rough sea conditions is emphasized as is the need for a highly capable, flexible, and reliabile flight control system. A three channel control by wire, digital flight control system is suggested. The requirement for automatic flight control, the advantage of control by wire implementation, the preference for a digital computer, and the need for three channel redundancy are among the factors discussed.

Konsewicz, R. K.↗

NASA NTRS1980

Landsat features for agricultural applications

This paper presents relationships among Landsat MSS bands and selected transformations of them, with emphasis on the Tasseled-Cap Transformation and its Brightness, Greenness variables. It also discusses relationships between reflectance measurements made in the Landsat spectral bands and actual Landsat data. Agronomically oriented analyses of reflectance measurements of wheat throughout a growing season are presented, with a comparison of various green measures, correlation with crop development stage, and examination of the effects of moisture stress. The final example addresses the use of transformed variables in a newly developed approach to forestry change detection.

Malila, W. A.↗

NASA NTRS2001

Astronaut Photography of Coral Reefs

Astronaut photographs of tropical coastal areas may contain information on submerged features, including coral reefs, up to depths of about 15 m in clear waters. Previous research efforts have shown that astronaut photographs can aid in estimating coral reef locations and extent on national, regional and global scales, and allow characterization of major geomorphological rim and lagoon features (Andrefouet et al. 2000, in preparation). They can be combined with traditional satellite data to help distinguish between clouds and lagoon features such as pinnacles (Andrefouet and Robinson, in review). Furthermore, astronaut photographs may provide reef scientists and managers with information on the location and extent of river plumes and sediment run off, or facilitate identification of land cover types, including mangroves (Webb et al., in press). Photographs included in the section were selected based on several criteria. The primary consideration of the editors was that the photographs represent a worldwide distribution of coral reefs, have extremely low visual interference by cloud cover, and display a spatial scale reasonable for examining reef-related features. Once photographs were selected, they were digitized from 2nd generation copies. The color and contrast were hand corrected to an approximation of natural color (required to account for spectral differences between photographs due to the color sensitivities of films used, and differences in sun angle and exposure of the photographs). None of the photographs shown here have been georeferenced to correct them to a map projection and scale. Any distortions in features due to slightly oblique look angles when the photographs were taken through spacecraft windows remain. When feasible, near vertical photographs have been rotated so that north is toward the top. An approximate scale bar and north arrow have added using distinctive features on each photograph with reference to a 1:1,000,000 scale navigation chart. Astronaut photographs provide a unique source of moderate resolution reef remote sensing data because of their global coverage and (immediate) availability in the public domain. The database of photographs can be searched an browsed online and high-resolution digital copies of photographs in this atlas can be accessed via the Website of Earth Science and Image Analysis at NASA's Johnson Space Center:

Robinson, Julie A.↗

NASA NTRS1991

TADPLOT program, version 2.0: User's guide

The TADPLOT Program, Version 2.0 is described. The TADPLOT program is a software package coordinated by a single, easy-to-use interface, enabling the researcher to access several standard file formats, selectively collect specific subsets of data, and create full-featured publication and viewgraph quality plots. The user-interface was designed to be independent from any file format, yet provide capabilities to accommodate highly specialized data queries. Integrated with an applications software network, data can be assessed, collected, and viewed quickly and easily. Since the commands are data independent, subsequent modifications to the file format will be transparent, while additional file formats can be integrated with minimal impact on the user-interface. The graphical capabilities are independent of the method of data collection; thus, the data specification and subsequent plotting can be modified and upgraded as separate functional components. The graphics kernel selected adheres to the full functional specifications of the CORE standard. Both interface and postprocessing capabilities are fully integrated into TADPLOT.

Hammond, Dana P.↗

DOE OSTI2026

Evaluation of LLVM Flang for Production HPC Applications and Modern Fortran Features

In 2025, LLVM released its first Flang Fortran compiler version considered ready for widespread evaluation. We know of no published assessment of Flang compiling a workload- derived portfolio of high-performance computing (HPC) applications. We address this gap using workload data from the National Energy Research Scientific Computing Center (NERSC), which supports more than 10,000 scientists on approximately 1,000 projects. The NERSC workload analyses identify many Fortran components in heavily used applications. We selected 10 such packages with available source code. We compiled them with Flang 22.1.3 on NERSC’s Perlmutter system. Six compiled without code modifications, though some required build-system changes. Three compiled after minor source edits, mostly to address Fortran standard violations. One built only without OpenMP enabled. We evaluated seven additional packages selected for their use of, or enablement of, standard Fortran parallel features: multi-image execution and do concurrent. Six such codes compiled with most or all unit tests passing.

Rasmussen, Katherine↗

DOE OSTI2020

eFESTA: Ensemble Feature Exploration with Surface Density Estimates

We propose surface density estimate (SDE) to model the spatial distribution of surface features-isosurfaces, ridge surfaces, and streamsurfaces-in 3D ensemble simulation data. The inputs of SDE computation are surface features represented as polygon meshes, and no field datasets are required (e.g., scalar fields or vector fields). The SDE is defined as the kernel density estimate of the infinite set of points on the input surfaces and is approximated by accumulating the surface densities of triangular patches. We also propose an algorithm to guide the selection of a proper kernel bandwidth for SDE computation. An ensemble Feature Exploration method based on Surface densiTy EstimAtes (eFESTA) is then proposed to extract and visualize the major trends of ensemble surface features. For an ensemble of surface features, each surface is first transformed into a density field based on its contribution to the SDE, and the resulting density fields are organized into a hierarchical representation based on the pairwise distances between them. The hierarchical representation is then used to guide visual exploration of the density fields as well as the underlying surface features. We demonstrate the application of our method using isosurface in ensemble scalar fields, Lagrangian coherent structures in uncertain unsteady flows, and streamsurfaces in ensemble fluid flows.

Computational modeling↗

NASA NTRS2004

Feature-Identification and Data-Compression Software

A report discusses the continuing development of Windows Interface for Nominal Displacement Selection (WINDS), a computer program for automated analysis of images of the Sun and planets acquired by scientific instruments aboard spacecraft. WINDS is intended to afford capabilities for identification of features, measurement of displacements and velocities, analysis of terrain and of atmospheres, and synthesis of animation sequences of images of terrains and atmospheres from small sets of samples by use of velocity-based interpolation. A major element of WINDS will be a nonlinear correlator capable of tracking small features in complex image sequences. For dynamic image sequences, the correlator will enable compression of data by factors >100. In processing image data, WINDS will take account of such factors as texture in image data, rotation of features during measurement intervals, effects of viewing and solar illumination angles, and vertical structures of atmospheres. WINDS will also take account of positions, aiming directions, and fields of view of cameras to determine three-dimensional feature structures by use of triangulation and stereoscopic analysis techniques.

Jong, Eric De↗

NASA NTRS1995

Mission Success Driven Space System Sparing Analysis

Among the maintenance resources, the spare parts are the most difficult to predict. Items in the space systems are very different from the point of view of reliability, cost, weight, volume, etc. The different combinations of spares make different contribution to the: mission success, spare investment, volume occupied and weight. Hence, the selection of spares for a mission planned must take into account all of these features. This paper presents the generic mission success driven sparing model developed, for the complex space systems. The mathematical analysis used in the model enables the user to select the most suitable selection of the spare package for the mission planned. The illustrative examples presented clearly demonstrate the applicability and usefulness of the model introduced.

Knezevic, J.↗