Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyte additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electrochemically Assisted Single Crystal Growth of Reduced Preyssler Polyoxometalates Decorated with M 2+ ( M = Co, Ni) and Cubane–Like Ni 4 O 4 Units

Polyoxometalates (POMs) are of great interest to the scientific community, and their reduction and nucleation have been well–established by multi–step techniques. The present study develops an electrochemical approach for simultaneous reduction and nucleation of polyoxometalate–containing solids. Herein we report crystal growth of reduced Preyssler polyoxotungstate–based (anionic formula [NaP 5 W 30 O 110 ] 14– ) new crystalline solids made of Preyssler anions interlinked by Co 2+ and Ni 2+ ions. Crystal nucleation and in situ reduction were achieved at room temperature using a two silver wire electrode setup in various aqueous solutions under constant applied potentials. The POM material was deposited on the cathode, and its structure was characterized by X–ray diffraction techniques. The primary structure type observed involves POMs decorated by disordered Co 2+ /Ni 2+ octahedra and fused into 1–D pillars by additional Co 2+ /Ni 2+ octahedra. Additionally, a secondary phase was observed in the Ni–based reactions, where reduced Preyssler anions are decorated by Ni 4 O 4 cubane–like units. To understand the electrochemical process, polarization curves of the electrolyte solutions are presented, suggesting an applied potential best suited for crystal growth. The work highlights the effectiveness of an electrochemical pathway where nucleation and simultaneous reduction of POMs can make novel reduced POM solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Prospects for Employing Lithium Copper Phosphates as High-Voltage Li-Ion Cathodes

Three compositions of lithium copper phosphates: Li 2 CuPO 4 , Li 2 Cu 5 (PO 4 ) 4 , and Li 2 CuP 2 O 7 have been studied as potential high-voltage cathode materials for Li-ion batteries, following computational predictions of high operating voltages. An assisted-microwave preparation of Li 2 CuPO 4 , which is otherwise difficult to prepare in nearly pure form, has been developed. The electrochemical performance of all three compounds has been investigated. Additionally, the cyclability of these materials is found to be poor due to structural changes, irreversible reduction to metallic copper at potentials as high as 2.5 V, and the possibility of dissolution into the electrolyte. Some general understanding in regard to the use of Cu compounds in redox electrodes is presented.

25 ENERGY STORAGE↗
DOE OSTI2025

Defect formation and microstructure tuning via proton irradiation to control electrochemical and phase reversibility in layered battery materials

The reversibility of phase transformation influences the functionality of electrode materials in batteries. In many battery materials, nanosized grains favor phase reversibility but at the cost of cyclability due to aggravated side reactions with the electrolyte. Here, in this study, we present a novel approach to enhance the phase transformation reversibility of layered oxide cathodes, exemplified by Na 2/3 Fe 1/2 Mn 1/2 O 2 through proton irradiation. In addition to forming defects, proton irradiation at sufficiently high doses can subdivide single grains into multiple nanodomains without physically rupturing them. Hence, the single grains of the material assume a pseudo-secondary particle nature without reducing the overall grain size. Preserving the grain size is advantageous, as it reduces side reactions, which is not possible with conventional grain size reduction methods. While chemical transformations and defect formation induced through proton irradiation can influence the stability of battery materials, it is expected that structural reorganization due to cycling-induced phase transformation will be contained within these nanodomains. Such confinement of phase transformation is potentially responsible for enhancing the reversibility of layered oxide materials in our study. Thus, our study suggests that grain subdivision could become an effective microstructure tuning strategy for managing electrochemical cycling-induced phase changes in battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Process for making manganese dioxide and its polymorphs reversible

A method of forming a layered manganese dioxide for use in a cathode of a battery comprises disposing a cathode into a housing of an electrochemical cell, disposing an anode into the housing, disposing a polymeric separator between the anode and the cathode such that the anode and the cathode are electrically separated, adding an alkaline electrolyte to the housing, cycling the electrochemical cell into the 2nd electron capacity of the manganese dioxide, and forming a layered manganese dioxide having a layered manganese dioxide structure with the one or more additives incorporated into the layered manganese dioxide structure. The cathode comprising a cathode material comprising: a manganese dioxide compound, one or more additives selected from the group consisting of bismuth, copper, tin, lead, silver, cobalt, nickel, magnesium, aluminum, potassium, lithium, calcium, gold, antimony, iron, zinc, and combinations thereof, and a conductive carbon.

Yadav, Gautam G.↗
DOE OSTI2020

Potassium Prussian blue-coated Li-rich cathode with enhanced lithium ion storage property

With high specific capacity, the layered Li-rich Mn-based oxide (LRMO) is a promising candidate cathode material for Li-ion batteries. However, the irreversible release of Li-ions during the first charging process, instability of LRMO/electrolyte interface and relatively low ion conductivity of LRMO result in low initial Coulombic efficiency (ICE), poor cycle stability and rate performance, which prohibit its further application. Furthermore, interface engineering via additive coating is expected to effectively address these issues. Herein, we rely on potassium Prussian blue (KPB), a Li + acceptor with good ion conductivity, as a new coating material on LRMO particles. The KPB coating not only forms a protective layer on the surface of LRMO against electrolyte corrosion, but also functions as a host for Li + transport and accommodation, leading to enhanced ion conductivity and ICE of LRMO cathode. Consequently, 2 wt% KPB coated LRMO cathode achieved an initial discharge capacity of up to 281.7 mA h g -1 with an ICE of 85.69% compared to an ICE of 79.52% for the LRMO cathode without coating. The cycling and rate performance are also greatly improved as evidenced by the well maintained capacity of up to 176.8 mA h g -1 after 100 cycles at a current density of 0.5 C, compared to the limited capacity of only 135.3 mA h g -1 for the LRMO cathode without coating. Overall, this work pioneers the use of potassium Prussian blue as additive coating material to enhance performance of LRMO cathode, and we expect it to inspire the battery community with new strategies of material engineering/design toward practical application in high-energy lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Electrolytically Assisted Surface Decontamination (EASD{sup TM}) for POCO Operations - 20282

NNL in collaboration with C-Tech Innovation Ltd and Sellafield Ltd has been exploring innovative technologies to enable a significant reduction of radiological hazards within facilities during the Post Operational Clean Out (POCO) phase of a nuclear plant's life cycle. Reducing the hazard by effectively decontaminating plants in-situ during POCO delivers huge cost reductions for future decommissioning operations. These cost reduction benefits are realized by reducing the number and complexity of remote operations as well as lowering the long-term waste disposal costs. Whilst chemical decontamination can achieve the desired level of decontamination, applying aggressive chemical reagents is hazardous, potentially difficult to control and requires there to be complimentary effluent treatment and waste routes. This work has aimed to develop flexible and controllable decontamination processes which could be operated without the additional complexity and issues associated with chemical decontamination. The processes needed to be relatively fast and effective to minimize the time operators would spend in an active area. In addition, there was a driver to produce decontamination methodologies which generated a secondary waste compatible with current routes and which takes advantage of current waste capacity. The strategy therefore was to come up with a solution that works with, rather than against, the science and engineering behind process plants at Sellafield. Electrolytically Assisted Surface Decontamination (EASD{sup TM}) is an innovative electrochemical decontamination process (developed by NNL and C-Tech Innovation Ltd) that can remove activity from contaminated metal in very short time periods. Application of the patented electric waveform to the surface when treating contaminated metal with nitric acid has been shown to significantly enhance the decontamination performance. When compared to proposed baseline washout procedures at Sellafield, the only change to the process is the applied electrical waveform which is temporary and controllable. The current causes dissolution of the metal surface being decontaminated which leads to activity transferring from the plant item into the nitric acid effluent stream. This innovation has the potential to transform the POCO process and allow a nitric acid based washout approach to deliver POCO quickly and cost effectively within the existing infrastructure. Several devices have now been designed that incorporate this EASD{sup TM} technology and enable the decontamination process to be applied to a range items commonly identified as being contaminated during nuclear decommissioning programmes such as pipework, tanks and hotspots of walls/floors. Inactive and active laboratory-scale testing has been completed using both simulated and 'real-life' contaminated (low level waste) metallic items retrieved from different nuclear sites. Active trials demonstrated that contaminated items could be treated to free release levels within minutes. Engineering scale tests are currently being performed, with guidance from Sellafield's system engineers and plant managers, to provide the necessary re-assurance the designed devices could be successfully deployed in an on-plant scenario. The final stage of this development work is to carry out an active demonstration of the decontamination technology on Thorp at Sellafield. This paper aims to highlight progress made to date with the EASD{sup TM} technology and, more specifically, the development of an in-situ decontamination device for deployment within radioactive pipework. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Pressure effects on lithium anode/nickel-manganese-cobalt oxide cathode pouch cells through fixture design

Applying external pressure to a pouch cell results in improved performance, implicating systems-level design of batteries. Here, different formats and amounts of external pressure to Li-Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 (Li-NMC811) pouch cells were studied under lean electrolyte conditions. Due to the more uniform lithium plating/stripping, a constant gap fixture that retains the distance of the frame during cycling performed greater than a constant pressure fixture that retains applied pressure to the cell. In addition, the use of flexible foam in a constant gap fixture revealed enhanced cycle life at 10 psi; however, at 30 psi, the use of a rigid plate extended cycle life to over 250 cycles, while the foam severely shortened cycle life. This discrepancy with pressure was proven to be driven by stress distribution on cell components. The failure mechanisms and the effects of pressure fixture design on cell components were unveiled, shedding light on improving high-energy battery performance through at-scale fixture design.

25 - ENERGY STORAGE↗
DOE OSTI2021

Nanotechnology for Sulfur Cathodes

The field of lithium-sulfur batteries has benefited enormously from the advances in nanotechnology. At each step of technological improvement, lithium-sulfur batteries have relied upon techniques and methodologies brought upon by nanotechnology. Nanoporous material, heterogeneous nanocomposite, and hierarchical electrode developments have all been well-established as critical milestones for lithium-sulfur batteries. Overall, this review will briefly discuss the specific major roles of nanotechnology in lithium-sulfur batteries regarding practically relevant testing conditions in addition to research trends and future directions for electrocatalysis.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrochemical and Chemical Reactivities of Titanium Oxide-Based Materials with a Chloroaluminate Ionic Liquid Electrolyte for Aluminum Batteries

Here, by selecting three different types of electrode materials, we intended to better understand the Al 3+ intercalation chemistry of titanium oxide-based frameworks with an acidic chloroaluminate electrolyte. In agreement with previous reports, we confirmed that the native interstitial sites of anatase TiO 2 are less prone to accommodate Al 3 + than Li + or Na + ions, while introducing cationic vacancies largely increases the electrochemical storage capacity. Upon the first cycle, the highest reversible capacity, up to 277 mAh/g, was obtained for a hydrated layered structure featuring cationic vacancies. Total scattering data showed that the insertion of Al 3+ ions induced a strong distortion of the framework. In addition, combined 27 Al MAS NMR and DFT calculations revealed that in oxy-hydroxylated vacant sites, the coordination mode of Al 3+ ions depends on the arrangement of anions around vacancies inducing the occurrence of 4-, 5-, and 6-fold coordination modes. Further cycling experiments revealed a progressive capacity fading for all electrode materials. Using cyclic voltammetry on the used electrolyte, we evidenced that a partial dissolution has occurred, which is more pronounced for the layered hydrate compound, and that solubilized species are electrochemically active, giving rise to specific signatures in both CVs and galvanostatic experiments. Raman spectroscopy enabled us to characterize these species, which are derived from the Ti-Cl system. The solubilized species, however, eventually precipitated, as shown by a purple deposit observed on the separator and tentatively assigned to TiCl 3 , known to be insoluble in this medium. By providing further information on the Al 3+ intercalation chemistry and a better understanding of the electrochemical and chemical reactivities of electrode materials, this work will enable progress to be made in the development of aluminum-ion batteries.

Al3+-ion insertion chemistry↗
DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗
NASA NTRS1996

Physiological adaptations and countermeasures associated with long-duration spaceflights

Since 1961, there have been more than 165 flights involving several hundred individuals who have remained in a space environment from 15 min to more than a year. In addition, plans exist for humans to explore, colonize, and remain in microgravity for 1000 d or more. This symposium will address the current state of knowledge in select aspects associated with the cardiovascular, fluid and electrolytes, musculoskeletal, and the neuroendocrine and immune systems. The authors will focus on responses, mechanisms, and the appropriate countermeasures to minimize or prevent the physiological and biochemical consequences of a microgravity environment. Since exercise is frequently cited as a generic countermeasure, this topic will be covered in greater detail. Models for simulated microgravity conditions will be discussed in subsequent manuscripts, as will future directions for ground-based research.

NASA Center ARC↗
NASA NTRSDate not supplied

Molten Salt Lattice Confinement Fusion (LCF) Fast Fission Reactor for Lunar and Planetary Surface Power

Molten salt fission reactors (MSR) have been suggested for lunar and planetary surface power systems. They have the advantage of operating at high temperature, for efficient thermal-electrical conversion, low pressure, long-lived with high nuclear fuel burnup. MSR are often designed to breed fissile 233U from natural 232Th by neutron capture and  decay via: 232Th(n,)233Th(,)233Pa(,)233U Unfortunately, this process requires 233Pa isotope separation and segregation to decay to 233U. This requirement prevents additional neutron capture that interferes with 233U breeding. Instead, Wooley’s sub-critical, fast fission, molten salt reactor would use externally generated tokamak fusion neutrons1,2 to fission all actinides.We propose a simpler fusion-fast-fission sub-critical reactor that generates fast neutrons in situ from lattice confinement fusion (LCF) to fission fertile and fissile actinides. This hybrid reactor doesn't require enriched 235U fissile pins to initiate fis-sion reactions, nor 233Pa separation and segregation during operation. Like Wooley’s, this hybrid reactor “burns” natural uranium (238U) or thorium (232Th) which avoids uranium enrichment and additional fissile material launch safety and security costs. The LCF neutron source is initiated by bremsstrahlung photoneutrons (Fig. 1)3 or isotopic neutron sources in electron-screened lattices (Fig. 2)4,5. Alternatively, the electrolytic Pd-deuterium co-deposition6protocol fast fissions7 both 232Th and 238U. However, an aqueous electrolyte-based system, without pressurization similar to conventional pressurized water fission reactors, is incapable of high temperatures due to the boiling point of the electrolyte slightly over 100 C. Molten salts can be used instead as was demonstrated at the University of Hawaii8 using a variety of Ni and Pd cathodes in lithiated, hydrided and deuterated salts. These salts have melting points often exceeding 500C making them suitable to efficiently produce electrical power9 through either Advanced Stirling Genera-tors (< 100 kWe) or closed-Brayton Cycle (> 100 kWe). This hybrid reactor could power a wide range of lunar or Martian applications from unmanned in-struments, to charging vehicles and entire facilities such as human habitats or in situ resource utilization. The power conversion cycles are Carnot Cycle limited, but generally 30% efficient at best. However, waste heat on the moon or Mars is important to surviving either two-week lunar nights or Martian nights as well as providing process heat for mineral extraction and “living off the land”

Lawrence Forsley↗
DOE OSTI2025

The Origin of Improved Performance in Boron‐Alloyed Silicon Nanoparticle‐Based Anodes for Lithium‐Ion Batteries

Stabilizing the solid electrolyte interphase (SEI) remains a key challenge for silicon‐based lithium‐ion battery anodes. Alloying silicon with secondary elements like boron has emerged as a promising strategy to improve the cycle life of silicon anodes, yet the underlying mechanism remains unclear. To address this knowledge gap, how boron concentration influences battery performance is systematically investigated. These results show a near‐monotonic increase in cycle lifetime with higher boron content, with boron‐rich electrodes significantly outperforming pure silicon. Additionally, silicon‐boron alloy anodes exhibit nearly three times longer calendar life than pure silicon. Through detailed mechanistic analysis, alternative contributing factors are systematically ruled out, and it is proposed that improved passivation arises from a strong permanent dipole at the nanoparticle surface. This dipole, formed by undercoordinated and highly Lewis acidic boron, creates a static, ion‐dense layer that stabilizes the electrochemical interface, reducing parasitic electrolyte decomposition and enhancing long‐term stability. These findings suggest that, within the SEI framework, the electric double layer is an important consideration in surface passivation. This insight provides an underexplored parameter space for optimizing silicon anodes in next‐generation lithium‐ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

A Fluoride-Rich Solid-Like Electrolyte Stabilizing Lithium Metal Batteries

To address the problems associated with Li metal anodes, a fluoride-rich solid-like electrolyte (SLE) that combines the benefits of solid-state and liquid electrolytes is presented. Its unique triflate-group-enhanced frame channels facilitate the formation of a functional inorganic-rich solid electrolyte interphase (SEI), which not only improves the reversibility and interfacial charge transfer of Li anodes but also ensures uniform and compact Li deposition. Furthermore, these triflate groups contribute to the decoupling of Li + and provide hopping sites for rapid Li + transport, enabling a high room-temperature ionic conductivity of 1.1 mS cm -1 and a low activation energy of 0.17 eV, making it comparable to conventional liquid electrolytes. Consequently, Li symmetric cells using such SLE achieve extremely stable plating/stripping cycling over 3500 h at 0.5 mA cm -2 and support a high critical current up to 2 mA cm -2 . Here, the assembled Li||LiFePO 4 solid-like batteries exhibit exceptional cyclability for over 1 year and a half, even outperforming liquid cells. Additionally, high-voltage cylindrical cells and high-capacity pouch cells are demonstrated, corroborating much simpler processibility in battery assembly compared to all-solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Anomalously high elastic modulus of a poly(ethylene oxide)-based composite electrolyte

The practical use of lithium metal anodes in solid-state batteries requires a polymer membrane with high lithium-ion conductivity, thermal/electrochemical stability, and mechanical strength. The primary challenge is to effectively decouple the ionic conductivity and mechanical strength of the polymer electrolytes. We report a remarkably facile single step synthetic strategy based on in-situ crosslinking of poly(ethylene oxide) (xPEO) in the presence of a woven glass fiber (GF). Such a simple method yields composite polymer electrolytes (CPE) of anomalously high elastic modulus up to 2.5 GPa over a broad temperature range (20 °C – 245 °C) that has never been previously documented. An unsupervised machine learning algorithm, K-mean clustering analysis, was implemented on the hyperspectral Raman mapping at the xPEO/GF interface. Using such a unique means, we show for the first time that the promoted mechanical strength originates from xPEO and GF interactions through dynamic hydrogen and ionic bonding. High ionic conductivity is achieved by the addition plasticizer (e.g. tetraglyme), where trifluoromethanesulfonate anions are tethered to the xPEO matrix and Li + cations are favorably transported through coordination with the plasticizer. Further, stringent galvanostatic cycling tests indicates the CPE can be stably cycled for >3000 h in a Li-metal symmetric cell at a moderate temperature (nearly 1500 Coulombs/cm 2 Li equivalents), outperforming most of the PEO-based electrolytes. The GF reinforced CPE reported here has multifunctional uses, such as solid electrolytes for all solid-state batteries and membranes for redox-flow batteries. Although the focus of this study is on lithium-based batteries, the results are equally promising for other alkali metal based batteries such as sodium and potassium.

25 ENERGY STORAGE↗
DOE OSTI2022

Characterizing the Geometry and Quantifying the Impact of Nanoscopic Electrocatalyst/Semiconductor Interfaces under Solar Water Splitting Conditions

The materials that are receiving the most attention in photoelectrochemical water splitting are metallic nanoparticle electrocatalysts (np-EC) attached to the surface of a semiconductor (SC) light absorber. In these multicomponent systems, the interface between the semiconductor and electrocatalysts critically affects performance. However, the np-EC/SC interface remains poorly understood as it is complex on atomic scales, dynamic under reaction conditions, and inaccessible to direct experimental probes. This contribution sheds light on how the electrocatalyst/semiconductor interface evolves under reaction conditions by investigating the behavior of nickel electrocatalysts (as nanoparticles and films) deposited on silicon semiconductors. Rigorous electrochemical experiments, interfacial atomistic characterization, and computational modeling are combined to demonstrate critical links between the atomistic features of the interface and the overall performance. It is shown that electrolyte-induced atomistic changes to the interface lead to (1) modulation of the charge carrier fluxes and a dramatic decrease in the electron/hole recombination rates and (2) a change in the barrier height of the interface. Additionally, the critical roles of nonidealities and electrocatalyst coverage due to interfacial geometry are explored. Each of these factors must be considered to optimize the design of metal/semiconductor interfaces which are broadly applicable to photoelectrocatalysis and photovoltaic research.

36 MATERIALS SCIENCE↗