Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

A Comparative Study of Deformation Behaviors Between Laser-Welded Joints and Base Metal of Ti-22Al-24.5Nb-0.5Mo Alloy

The tensile deformation behaviors of laser-welded Ti-22Al-24.5Nb-0.5Mo alloy joints have been investigated at room temperature and 650 °C using in situ tensile analysis methods. The α{sub 2} phase had a significant influence on deformation behaviors of base metal at room temperature and 650 °C. The microcracks mainly nucleated in B2/α{sub 2} phase boundaries or within α{sub 2} phase and then propagated along B2/α{sub 2} phase boundaries subsequently. Compared with the plastic fracture of base metal, the fracture modes of the fully B2-phase fusion zone at room temperature and 650 °C were quasi-cleavage and intergranular fracture, respectively. While dislocation slips became foremost deformation mode in the fusion zone at room temperature, there were a great amount of slip bands on the surface of grains caused by the slip systems. The microcracks of fusion zone at 650 °C nucleated and propagated along the grain boundaries of B2 phase. Owing to the lack of grain deformation, the cross-slip bands were in small quantities on the surface of B2 phase grains.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior of Aluminum Alloys AA7010 and AA7075

The hot deformation behavior of high-strength aluminum alloys AA7010 and 5 was studied through hot isothermal compression testing in the temperature regime of 623-723 K (at an interval of 25 K) and at varying strain rates (0.001 to 10 s{sup −1}). The safe zone of hot workability of both the alloys was determined using the instability criteria and correlating with the microstructure evolution. Zener–Hollomon parameters were calculated, and constitutive equations were also derived. Common characteristics observed in both the alloys were adiabatic shear band formation at a temperature of 623 K and strain rate of 10 s{sup −1} and flow localization at combination of all temperatures and high strain rate of 10 s{sup −1} with evolution of very fine recrystallized (DRX) grains. High-temperature resistance to deformation, large extent of recrystallization and relatively larger zone of stable deformation and higher activation energy in Al alloy AA7010 were observed as compared to AA7075. Considering the role of precipitates, dynamic recrystallization was found to have significant role in governing the hot deformation behavior of the alloys. Prediction of constitutive equations was found to be more accurate at higher temperatures and at moderate-to-high strain rates with relatively less error in AA7075 alloy as compared to AA7010 alloy.

36 MATERIALS SCIENCE↗

Effect of Plastic Deformation on Passivation Characteristics of Type 304 Stainless Steel

Electrochemical response of Type 304 stainless steel, with different levels of plastic deformation, was investigated in solutions containing different amounts of H{sub 2}SO{sub 4} and KSCN at room temperature. Potentiodynamic polarization and double-loop electrochemical potentiokinetic reactivation (DL-EPR) techniques were used to characterize different levels of plastic deformation. The results have indicated that DL-EPR values and passivation current density increased with increase in plastic deformation. The DL-EPR values were correlated well with hardness and fraction of strain-induced martensite. Attack during DL-EPR tests occurred on strain regions within the matrix such as dislocations in austenite and martensite and/or interface between austenite and martensite. No well-defined correlation was observed between the levels of plastic deformation and potentiodynamic polarization behavior.

36 MATERIALS SCIENCE↗

The role of twinning deformation on the hardening response of polycrystalline magnesium from discrete dislocation dynamics simulations

The mechanical response of micro-twinned polycrystalline magnesium was studied through three-dimensional discrete dislocation dynamics (DDD). A systematic interaction model between dislocations and (1012) tension twin boundaries (TBs) was proposed and introduced into the DDD framework. In addition, a nominal grain boundary (GB) model agreeing with experimental results was also introduced to mimic the GB’s barrier effect. The current simulation results show that TBs act as a strong obstacle to gliding dislocations, which contributes significantly to the hardening behavior of magnesium. On the other hand, the deformation accommodated by twinning plays a softening role. Therefore, the concave shape of the Mg stress-strain curve results from the competition between dislocation-TB induced hardening and twinning deformation induced softening. At low strain levels, twinning deformation induced softening dominates and a decreasing hardening rate is observed in Stage-I. In Stage-II, both the hardening and softening effects decline, but twinning deformation induced softening declines faster, which leads to an increasing hardening rate.

36 MATERIALS SCIENCE↗

Anisotropic deformation of extruded magnesium alloy AZ31 under uniaxial compression: A study with simultaneous in situ synchrotron x-ray imaging and diffraction

In situ synchrotron x-ray imaging and diffraction are used to investigate anisotropic deformation of an extruded magnesium alloy AZ31 under uniaxial compression along two different directions, with the loading axis (LA) either parallel or perpendicular to the extrusion direction (ED), referred to as LA∥ED and LAED, respectively. Multiscale measurements including stress–strain curves (macroscale), x-ray digital image correlation (mesoscale), and diffraction (microscale) are obtained simultaneously. Electron backscatter diffraction is performed on samples collected at various strains to characterize deformation twins. The rapid increase in strain hardening rate for the LA∥ED loading is attributed to marked {101¯2} extension twinning and subsequent homogenization of deformation, while dislocation motion leads to inhomogeneous deformation and a decrease in strain hardening rate.

36 MATERIALS SCIENCE↗

Mapping local deformation behavior in single cell metal lattice structures

The deformation behavior of metal lattice structures is extremely complex and challenging to predict, especially since strain is not uniformly distributed throughout the structure. Understanding and predicting the failure behavior for these types of light-weighting structures is of great interest due to the excellent scaling of stiffness- and strength-to weight ratios they display. Therefore, there is a need to perform simplified experiments that probe unit cell mechanisms. This study reports on high resolution mapping of the heterogeneous structural response of single unit cells to the macro-scale loading condition. Two types of structures, known to show different stress-strain responses, were evaluated using synchrotron radiation micro-tomography while performing in-situ uniaxial compression tests to capture the local micro-strain deformation. These structures included the octet-truss, a stretch-dominated lattice, and the rhombic-dodecahedron, a bend-dominated lattice. The tomographic analysis showed that the stretch- and bend-dominated lattices exhibit different failure mechanisms and that the defects built into the structure cause a heterogeneous localized deformation response. Also shown here is a change in failure mode for stretch-dominated lattices, where there appears to be a transition from buckling to plastic yielding for samples with a relative density between 10 and 20%. In conclusion, the experimental results were also used to inform computational studies designed to predict the mesoscale deformation behavior of lattice structures. Here an equivalent continuum model and a finite element model were used to predict both local strain fields and mechanical behavior of lattices with different topologies.

36 MATERIALS SCIENCE↗

Deformation response of AgCu interfaces investigated by in situ and ex situ TEM straining and MD simulations

The mechanisms of strain transfer across Ag/Cu interfaces were determined by a combination of in situ and ex situ TEM straining experiments and molecular dynamics simulations. Minimizing the magnitude of the Burgers vector of the residual dislocation generated in the interface was the dominant factor for determining the outcome of dislocation and deformation twin interactions with both non-coherent twin and cube-on-cube interfaces. This included the unexpected finding, due to the loading condition, of deformation twin activation in the Cu layer due to the intersection of deformation twins in Ag with the interface. As a result, deformation twin nucleation in Ag from the non-coherent twin interfaces was also explained by a Burgers vector minimization argument.

36 MATERIALS SCIENCE↗

In situ, 3D characterization of the deformation mechanics of a superelastic NiTi shape memory alloy single crystal under multiscale constraint

Microstructural elements in NiTi shape memory alloys (SMAs) – precipitates, phase boundaries, inclusions, grain boundaries – can be viewed as sources of multiscale constraint that influence their deformation response. In this paper, we characterized in situ, and in 3D, the deformation and the evolution of microstructure during a tension test in a superelastic NiTi specimen containing some of these sources of constraint. The method used was far-field high-energy X-ray diffraction microscopy (ff-HEDM), complemented by electron microscopy. We simulated the local stress state in the specimen using a microstructural model informed by the experimental data. Using these combined microstructure, deformation, and stress data, we report three phenomena, and relate them to specific sources of constraint. During initial elastic loading, axial lattice strain in austenite increased monotonically. On partial stress-induced phase transformation to martensite, the stress redistributed to both phases leading to a stress relaxation in austenite. The specimen contained a dense distribution of inclusions, which led to the activation of martensite habit plane variants that produce less than theoretical maximum transformation strain. Large Ni 4 Ti 3 precipitates potentially contributed to the poor transformation response. Under load, proportional gradients in local rotation and elastic stretch developed in the martensite phase, because of the constraint at phase interfaces. Finally, this combined ff-HEDM, electron microscopy, microstructural simulation toolbox provides a versatile method to understand the effect of constraint on inelastic deformation in other alloys with hierarchical microstructure.

36 MATERIALS SCIENCE↗

Microparticle impact-bonding modes for mismatched metals: From co-deformation to splatting and penetration

In this paper we present a comprehensive experimental campaign of high-velocity microparticle impacts with different combinations of particle and substrate materials to identify possible deformation regimes. Based on experimental observations of the impact sites, we identify three typical modes of behavior, namely, splatting, co-deformation, and penetration. We develop a theoretical framework to predict the operative bonding regime for a given particle/substrate combination, ranging from splatting and penetration at two extremes of a spectrum, and co-deformation in the center. We propose an impact ratio based on the materials’ properties, which can successfully quantify the spectrum. Co-deformation is expected when the ratio is around unity, while much larger or smaller ratios give rise to penetration and splatting, respectively.

36 MATERIALS SCIENCE↗

Deformed 'commutative' Chern-Simons' system

Noncommutative Chern-Simons' system is non-perturbatively investigated at a full deformed level. A deformed 'commutative' phase space is found by a non-canonical change between two sets of deformed variables of noncommutative space. It is explored that in the 'commutative' phase space all calculations are similar to the case in commutative space. Spectra of its energy and angular momentum of the Chern-Simons' system are obtained at the full deformed level. The noncommutative-commutative correspondence is clearly showed. Formalism for the general dynamical system is briefly presented. Some subtle points are clarified.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deformation behavior and phase transformation of nanotwinned Al/Ti multilayers

We report nanotwinned Al/Ti multilayers have exhibited size-dependent microstructure evolution and high strength. However, their deformation mechanisms are less well understood. In this work, we investigated the deformation mechanisms of nanotwinned Al/Ti multilayers with FCC/HCP layer interfaces by using in situ micropillar compression tests. Nanotwinned Al/Ti multilayers exhibit compressive strength up to 2.4 GPa and good work hardening capability. Post-compression TEM analyses reveal high-density stacking faults and the HCP-to-FCC phase transformations in Ti. Molecular dynamics simulations elucidate the mechanisms of deformation induced phase transformation in Ti and the influence of collective movement of partial dislocations on the deformability of Al/Ti multilayers.

36 MATERIALS SCIENCE↗

Linkage between lipid droplet formation and nuclear deformation in HeLa human cervical cancer cells

Highlights: • Oleic acid (OA) induces cytoplasmic, but not nucleoplasmic, LDs in HeLa cells. • Cells harboring OA-induced cytoplasmic LDs exhibit deformity of the nucleus. • Multinucleation by paclitaxel and reversine treatment coincides with LD formation. • LD formation and nuclear deformation are mutually affectable. Because lipid droplets (LDs) and the nucleus are cellular organelles that regulate seemingly very different biochemical processes, very little attention has been focused on their possible interplay. Here, we report a correlation between nuclear morphology and cytoplasmic LD formation in HeLa human cervical cells. When the cells were treated with oleic acid (OA), LDs were formed in the cytoplasm, but not in the nucleoplasm. Interestingly, cells harboring OA-induced cytoplasmic LDs showed deformity of the nucleus, particularly at the nuclear rim. Conversely, when alteration from a single spherical nuclear shape to a multinucleated form was enforced by coadministration of paclitaxel and reversine, a significant amount of LDs was detected in the cytoplasm of the multinucleated cells. These two distinct pharmacological culture conditions not only allow analysis of the previously underappreciated organelle relationship, but also provide insights into the mutual affectability of LD formation and nuclear deformation.

60 APPLIED LIFE SCIENCES↗

An isogeometric finite element formulation for phase transitions on deforming surfaces

This paper presents a general theory and isogeometric finite element implementation for studying mass conserving phase transitions on deforming surfaces. The mathematical problem is governed by two coupled fourth-order nonlinear partial differential equations (PDEs) that live on an evolving two-dimensional manifold. For the phase transitions, the PDE is the Cahn–Hilliard equation for curved surfaces, which can be derived from surface mass balance in the framework of irreversible thermodynamics. For the surface deformation, the PDE is the (vector-valued) Kirchhoff–Love thin shell equation. Both PDEs can be efficiently discretized using C 1 -continuous interpolations without derivative degrees-of-freedom (dofs). Structured NURBS and unstructured spline spaces with pointwise C 1 -continuity are utilized for these interpolations. The resulting finite element formulation is discretized in time by the generalized-α scheme with adaptive time-stepping, and it is fully linearized within a monolithic Newton–Raphson approach. A curvilinear surface parameterization is used throughout the formulation to admit general surface shapes and deformations. The behavior of the coupled system is illustrated by several numerical examples exhibiting phase transitions on deforming spheres, tori and double-tori.

42 ENGINEERING↗

Geodetic measurements and numerical models of transient deformation at Raft River geothermal field, Idaho, USA

Here, we perform synthetic aperture radar interferometry using data acquired between 2004 and 2016 by the Envisat, and ALOS-2 satellite missions to measure transient deformation at the Raft River geothermal field in Cassia County in Southern Idaho where geothermal production began in late 2007. Time-series analysis of multiple interferometric pairs indicates uplift at an exponentially decaying rate, over an ~8 km-by-5 km area centered near three injection wells that recycle produced brine. Similarly, subsidence at an exponentially decaying rate is observed in a 4 km-by-4 km area west of the production wells. These two signatures stay in the same location in all of the well-correlated Envisat interferometric pairs spanning the time interval between 2007 and 2010. The boundary separating the uplifting and subsiding areas is associated with the steeply dipping Bridge fault zone. Using two-dimensional numerical models, we explore first-order, bi-directional coupling between hydrological and mechanical processes. Our results suggest that: (i) most of the deformation occurs due to pore pressure changes following the start of geothermal production, (ii) the rate of deformation decays to zero over a time scale on the order of ~5 years as the system reaches steady state, and (iii) a reservoir-scale permeability of the order of ~1E–14 m 2 is required to explain the transient deformation.

15 GEOTHERMAL ENERGY↗

Influence of stacking fault energy and hydrogen on deformation mechanisms in high Mn austenitic steels during in-situ tensile testing

High Mn austenitic steels are considered an economical alloy system for hydrogen storage and transport applications. This study used stacking fault energy (SFE) as a design parameter to achieve hydrogen embrittlement (HE)-resistant high Mn austenitic alloys. The role of hydrogen on the deformation mechanisms of low (29 mJ/m 2 ) and high SFE (49 mJ/m 2 ) alloys was evaluated through in-situ neutron diffraction during tensile loading. Hydrogen-precharging increased yield strength, partly due to hydrogen-induced lattice distortion (i.e., solute strengthening). Hydrogen accelerated the increase in defect density, including dislocations and stacking faults. The formation of planar deformation structures (twins and stacking faults), relative to dislocations, plays a critical role in promoting hydrogen-assisted fracture. The stacking fault frequency parameter obtained from neutron diffraction quantifies planar deformation tendencies, correlated with HE sensitivity. The higher SFE alloy exhibited greater resistance to HE, associated with the reduced propensity to form stacking faults and twins upon deformation in the hydrogen-precharged condition.

High Mn austenitic steel↗

Quantifying deformation processes near grain boundaries in α titanium using nanoindentation and crystal plasticity modeling

In this work, the influence of grain boundaries on plastic deformation was studied by carrying out nanoindentation near grain boundaries (GBs). Surface topographies of indentations near grain boundaries were characterized using atomic force microscopy (AFM) and compared to corresponding single crystal indent topographies collected from indentations in grain interiors. Comparison of the single crystal indents to indents adjacent to low-angle boundaries shows that these boundaries have limited effect on the size and shape of the indent topography. Higher angle boundaries result in a decrease in the pile-up topography observed in the receiving grain, and in some cases increases in the topographic height in the indented grain, indicating deformation transfer across these boundaries is more difficult. A crystal plasticity finite element (CPFE) model of the indentation geometry was built to simulate both the single crystal and the near grain boundary indentation (bi-crystal indentation) deformation process. The accuracy of the model is evaluated by comparing the point-wise volumetric differences between simulated and experimentally measured topographies. Good agreement, in both single and bi-crystal cases, suggests that the crystal plasticity kinematics plays a dominant role in single crystal indentation deformation, and is also essential to bi-crystal indentation. Despite the good agreement, some differences between experimental and simulated topographies were observed. These discrepancies have been rationalized in terms of reverse plasticity and the inability of the model to capture the full resistance of the boundary to slip. Lastly, this is discussed in terms of dislocation nucleation versus glide in the model and in the physics of the slip transfer process.

36 MATERIALS SCIENCE↗

Localization of deformation in fluid-saturated sandstone

Herein we discuss a laboratory study of inelastic deformation and localization was conducted to evaluate microseismicity and fracture in fluid-saturated rock. Plane strain compression experiments were performed on oil- and water-saturated Berea sandstone under dry, drained, undrained, and quasi-unjacketed conditions. Parameters associated with the elastic and inelastic material response were accurately measured and used in a constitutive model to predict localization of deformation under the drained and undrained conditions. Acoustic emission (AE) activity was recorded and the onset of inelastic response in fluid-saturated rock, similar to dry rock, coincided with an increase in AE rate. Fracture initiation and propagation were successfully monitored by AE locations. Clustering of AE events and the start of inhomogeneous deformation inferred from displacement measurements are shown to be well correlated with the model prediction of the onset of localized deformation under various rock-fluid interaction conditions.

42 ENGINEERING↗

Improving Soft-Tissue Contrast in Four-Dimensional Computed Tomography Images of Liver Cancer Patients Using a Deformable Image Registration Method

Purpose: To investigate a deformable image registration method to improve soft-tissue contrast in four-dimensional (4D) computed tomography (CT) images of the liver. Methods and Materials: Ten patients with hepatocellular carcinoma underwent 4D CT scan for radiotherapy treatment planning on a positron emission tomography/CT scanner. Four-dimensional CT images were binned into 10 equispaced phases. The exhale phase served as the reference phase, and images from the other nine phases were coregistered to the reference phase image using an intensity-based, automatic deformable image registration method. Then the coregistered images were combined to create a single, high-quality reconstructed CT image at exhale phase as the new reference for target delineation. The extent of image quality enhancement was quantified relative to the original CT by calculating the signal-to-noise ratio and the contrast-to-noise ratio. Results: The soft tissue image contrast was noticeably better after deformable image registration than in the original scans. Signal-to-noise ratios inside the liver region of interest increased for all patients by a factor of 3.0 (range, 2.3-3.7). The improvement in image quality was not linearly proportionate to the number of images averaged. Using only 6 phases can achieve at least 85% of the contrast enhancement that can be achieved using all 10 phases. We also found that contrast enhancement was inversely proportional to the original image quality (p = 0.006), and the contrast enhancement is attained with little loss of spatial resolution. Conclusions: This deformable image registration method is feasible to improve soft-tissue image quality in 4D CT images.

62 RADIOLOGY AND NUCLEAR MEDICINE↗