Results for “conditional shift” — Page 48

DOE OSTI2021

Influence of Fuel Properties on Gasoline Direct Injection Particulate Matter Emissions Over First 200 s of World-Harmonized Light-Duty Test Procedure Using an Engine Dynamometer and Novel “Virtual Drivetrain” Software

Abstract The influence of fuel properties on particulate matter (PM) emissions from a catalytic gasoline particulate filter (GPF) equipped gasoline direct injection (GDI) engine was investigated using novel “virtual drivetrain” software and an engine mated to an engine dynamometer. The virtual drivetrain software was developed in labview to operate the engine on an engine dynamometer as if it were in a vehicle undergoing a driving cycle. The software uses a physics-based approach to determine vehicle acceleration and speed based on engine load and a programed “shift” schedule to control engine speed. The software uses a control algorithm to modulate engine load and braking to match a calculated vehicle speed with the prescribed speed trace of the driving cycle of choice. The first 200 s of the World-harmonized Light-duty Test Procedure (WLTP) driving cycle was tested using six different fuel formulations of varying volatility, aromaticity, and ethanol concentration. The first 200 s of the WLTP was chosen as the test condition because it is the most problematic section of the driving cycle for controlling PM emissions due to the cold start and cold drive off. It was found that there was a strong correlation between aromaticity of the fuel and the engine-out PM emissions, with the highest emitting fuel producing more than double the mass emissions of the low PM production fuel. However, the post-GPF PM emissions depended greatly on the soot loading state of the GPF. The fuel with the highest engine-out PM emissions produced comparable post-GPF emissions to the lowest PM producing fuel over the driving cycle when the GPF was loaded over three cycles with the respective fuels. These results demonstrate the importance of GPF loading state when aftertreatment systems are used for PM reduction. It also shows that GPF control may be more important than fuel properties, and that regulatory compliance for PM can be achieved with proper GPF control calibration irrespective of fuel type.

Energy & Fuels↗

DOE OSTI2023

New thermal decomposition pathway for TATB

Abstract Understanding the thermal decomposition behavior of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is a major focus in energetic materials research because of safety issues. Previous research and modelling efforts have suggested benzo-monofurazan condensation producing H 2 O is the initiating decomposition step. However, early evolving CO 2 (m/z 44) along with H 2 O (m/z 18) evolution have been observed by mass spectrometric monitoring of head-space gases in both constant heating rate and isothermal decomposition studies. The source of the CO 2 has not been explained, until now. With the recent successful synthesis of 13 C 6 -TATB ( 13 C incorporated into the benzene ring), the same experiments have been used to show the source of the CO 2 is the early breakdown of the TATB ring, not adventitious C from impurities and/or adsorbed CO 2 . A shift in mass m/z 44 (CO 2 ) to m/z 45 is observed throughout the decomposition process indicating the isotopically labeled 13 C ring breakdown occurs at the onset of thermal decomposition along with furazan formation. Partially labeled (N 18 O 2 ) 3 -TATB confirms at least some of the oxygen comes from the nitro-groups. This finding has a significant bearing on decomposition computational models for prediction of energy release and deflagration to detonation transitions, with respect to conditions which currently do not recognize this oxidation step.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Numerical study of implosion instability mitigation in magnetically driven solid liner dynamic screw pinches

Magnetized liner inertial fusion experiments on the Z accelerator suffer from magneto-Rayleigh–Taylor instabilities (MRTI) that compromise integrity of the imploding cylindrical liner, limiting achievable fusion fuel conditions and ultimately reducing magneto-inertial fusion target performance. Dynamic screw pinches (DSP) provide a method to reduce MRTI in-flight via application of magnetic field line tension to the imploding liner outer surface. In contrast with z-pinches that drive implosions with an azimuthal magnetic field, dynamic screw pinches enforce an additional axial drive magnetic field component, making the overall drive magnetic field helical. As the liner implodes, cumulative MRTI development is reduced by dynamically shifting the orientation of the fastest growing instability modes. Three-dimensional magnetohydrodynamic simulations show that the DSP mechanism effectively stabilizes initially solid cylindrical liner implosions driven by Z-scale current pulses, indicating that MRTI mitigation increases with the ratio of axial to azimuthal drive magnetic field components (i.e., the drive field ratio). We also performed a spectral analysis of the simulated imploding density distributions, extracting wavelength and pitch angle of the simulated MRTI structures to study their dynamics during the implosion. Simulations of liners initially perturbed with drive-field-aligned sinusoidal structures indicate that MRTI mitigation in DSP implosions decreases with perturbation wavelength, once again suggestive of magnetic field line tension effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Managing Power Systems-Induced Wildfire Risks Using Optimal Scheduled Shutoffs

The increasing demands for electricity and the increase in extreme weather conditions are putting unprecedented pressure on our electric grids. Often, this pressure leads to electrical component failures, which might ignite wildfires. This work develops a novel model to balance the reliability of power network operations and the risk of wildfire ignition by opti- mizing the operational schedule of power transmission networks considering time-varying risk measures that include exogenous and operational factors. Energy storage systems are considered to deliver power during peak wildfire hours and enable temporal load shifting. The problem is formulated as a mixed-integer linear program that maximizes a weighted sum of the served power demand and the reduction in grid-induced wildfire risk. The results demonstrate the ability of the model to significantly reduce wildfire risk without considerable load shedding.

power systems operations↗

DOE OSTI2021

WA-Omic_LA.1.0 - Quantitative Lipidomics, Metabolomics, and Sequencing (16S/ITS) Publication Data DOI Package

Corresponding Data Publication: "Rapid remodeling of the soil lipidome in response to a drying-rewetting event." This study reveals specific changes in lipids and metabolites that are indicative of stress adaptation, substrate use, and cellular recovery during soil drying and subsequent rewetting. Drought induced nutrient limitation was reflected in the lipidome and polar metabalome, both of which rapidly shifted (within hours) upon rewet. Reduced nutrient access in dry soil caused the replacement of glycerophospholipids with phosphorus-free lipids and impeded resource-expensive osmolyte accumulation. Elevated levels of ceramides and lipids with long chain polyunsaturated fatty acids, in dry soil suggests that lipids play an important role in fungal drought tolerance. Increasing abundance of bacterial glycerophospholipids and triacylglycerols with fatty acids typical of bacteria and polar metabolites suggest metabolic recovery in representative bacteria once the environmental conditions are conducive for growth. These results underscore the importance of the soil lipidome as a robust indicator of microbial community responses, especially at the short time scales of cell-environment reactions. Data package contents reported here are the first version and contain pre- and post-processed data acquisition and subsequent downstream analysis files using various data source instrument method techniques and Mass Spectroscopy (MS) EMSL capabilities. This publication data package DOI is a comprehensive high-throughput multi-omics data lifecycle collection containing processed data method metadata. Support files include additional data download “Read Me” file containing data descriptor information and data source application ontologies (see data dictionary). Reported data download contents are structured for compliance with project data sharing guidelines, community standards initiatives, and sponsor stakeholder policies supporting FAIR data principles. For increased data availability and interoperability, GC-MS/LC-MS mass spectrometry datasets (Thermo .raw ) were deposited at the MassIVE database repository under the related data accession MSV000086931 and can be accessed by using the API. Statistical data processing software, analysis tools, and data workflows are listed below corresponding to the host repository long-term location.

Amplicon sequencing 16S ITS LC-MS/MS lipidomics mu↗

DOE OSTI2021

WA-Omic_LA.1.0 - Quantitative Lipidomics, Metabolomics, and Sequencing (16S/ITS) Publication Data DOI Package

Corresponding Data Publication: "Rapid remodeling of the soil lipidome in response to a drying-rewetting event." This study reveals specific changes in lipids and metabolites that are indicative of stress adaptation, substrate use, and cellular recovery during soil drying and subsequent rewetting. Drought induced nutrient limitation was reflected in the lipidome and polar metabalome, both of which rapidly shifted (within hours) upon rewet. Reduced nutrient access in dry soil caused the replacement of glycerophospholipids with phosphorus-free lipids and impeded resource-expensive osmolyte accumulation. Elevated levels of ceramides and lipids with long chain polyunsaturated fatty acids, in dry soil suggests that lipids play an important role in fungal drought tolerance. Increasing abundance of bacterial glycerophospholipids and triacylglycerols with fatty acids typical of bacteria and polar metabolites suggest metabolic recovery in representative bacteria once the environmental conditions are conducive for growth. These results underscore the importance of the soil lipidome as a robust indicator of microbial community responses, especially at the short time scales of cell-environment reactions. Data package contents reported here are the first version and contain pre- and post-processed data acquisition and subsequent downstream analysis files using various data source instrument method techniques and Mass Spectroscopy (MS) EMSL capabilities. This publication data package DOI is a comprehensive high-throughput multi-omics data lifecycle collection containing processed data method metadata. Support files include additional data download “Read Me” file containing data descriptor information and data source application ontologies (see data dictionary). Reported data download contents are structured for compliance with project data sharing guidelines, community standards initiatives, and sponsor stakeholder policies supporting FAIR data principles. For increased data availability and interoperability, GC-MS/LC-MS mass spectrometry datasets (Thermo .raw ) were deposited at the MassIVE database repository under the related data accession MSV000086931 and can be accessed by using the API. Statistical data processing software, analysis tools, and data workflows are listed below corresponding to the host repository long-term location.

Amplicon sequencing 16S ITS LC-MS/MS lipidomics mu↗

DOE OSTI2021

WA-Omic_LA.1.0 - Quantitative Lipidomics, Metabolomics, and Sequencing (16S/ITS) Publication Data DOI Package

Corresponding Data Publication: "Rapid remodeling of the soil lipidome in response to a drying-rewetting event." This study reveals specific changes in lipids and metabolites that are indicative of stress adaptation, substrate use, and cellular recovery during soil drying and subsequent rewetting. Drought induced nutrient limitation was reflected in the lipidome and polar metabalome, both of which rapidly shifted (within hours) upon rewet. Reduced nutrient access in dry soil caused the replacement of glycerophospholipids with phosphorus-free lipids and impeded resource-expensive osmolyte accumulation. Elevated levels of ceramides and lipids with long chain polyunsaturated fatty acids, in dry soil suggests that lipids play an important role in fungal drought tolerance. Increasing abundance of bacterial glycerophospholipids and triacylglycerols with fatty acids typical of bacteria and polar metabolites suggest metabolic recovery in representative bacteria once the environmental conditions are conducive for growth. These results underscore the importance of the soil lipidome as a robust indicator of microbial community responses, especially at the short time scales of cell-environment reactions. Data package contents reported here are the first version and contain pre- and post-processed data acquisition and subsequent downstream analysis files using various data source instrument method techniques and Mass Spectroscopy (MS) EMSL capabilities. This publication data package DOI is a comprehensive high-throughput multi-omics data lifecycle collection containing processed data method metadata. Support files include additional data download “Read Me” file containing data descriptor information and data source application ontologies (see data dictionary). Reported data download contents are structured for compliance with project data sharing guidelines, community standards initiatives, and sponsor stakeholder policies supporting FAIR data principles. For increased data availability and interoperability, GC-MS/LC-MS mass spectrometry datasets (Thermo .raw ) were deposited at the MassIVE database repository under the related data accession MSV000086931 and can be accessed by using the API. Statistical data processing software, analysis tools, and data workflows are listed below corresponding to the host repository long-term location.

Amplicon sequencing 16S ITS LC-MS/MS lipidomics mu↗

DOE OSTI2026

Connecting agriculture and renewable energy: insights into microclimatic changes, physiological, biochemical, and yield responses under agrivoltaics: a review

Agrivoltaics, the synergistic integration of agriculture and solar energy production on the same piece of land, has emerged as a compelling dual-use solution that maximizes land productivity while simultaneously addressing the need for sustainable agricultural practices and renewable energy generation. Despite the growing global interest in this dual-use system, the microclimatic shifts created beneath solar panels and their consequences for crop performance remain insufficiently synthesized. This review highlights the intricate interactions between agrivoltaics systems and plant microclimates, discussing their impacts on various physiological processes, metabolic pathways, and overall yield responses in different crop species. Evidence indicates that moderated light intensity and altered microclimates can enhance water-use efficiency, stabilize photosynthetic function, and trigger beneficial metabolic adjustments; however, responses remain highly species-specific and strongly dependent on regional climate conditions and panel configuration. Yield outcomes vary widely among vegetables, cereals, pulses, and fruit crops, highlighting the necessity for tailored agronomic strategies and crop selection within agrivoltaic designs. A critical knowledge gap identified in this review concerns the limited understanding of molecular and omics-level responses underlying plant adaptation to agrivoltaic environments. We further provide a detailed and interdisciplinary overview of adaptive agronomic strategies, and optimal crop selection, tailored to agrivoltaic systems. Despite the benefits of land use efficiency and simultaneous food and energy production, challenges remain concerning initial investment, technological adaptation, social and legal barriers, and shade-induced yield penalties. Further research in this area will be critical to enhancing the agricultural, environmental, and economic sustainability of agrivoltaics while simultaneously augmenting their practical utility and appeal to farmers in the future.

14 SOLAR ENERGY↗

DOE OSTI2025

Addressing the Safety of Next-Generation Batteries

Owing to increasing demand for low-cost energy storage with secure material supply chains, the battery community is approaching a pivotal shift beyond conventional lithium-ion (Li-ion) towards next-generation cells. Technologies that include alkali-metal anodes, solid electrolytes and earth-abundant materials such as sodium (Na) and sulfur (S) are reaching commercialization in cells. The abuse tolerance and thermal runaway hazards of such technologies diverge from conventional Li-ion cells. Consequently, designing safe batteries with next-generation materials requires a holistic approach to characterize cells and to understand their responses to abuse conditions from the beginning to the end of life. Here we provide a Perspective on how the safety and abuse tolerance of cells are likely to change for up-and-coming technologies; challenges and opportunities for reimagining safe cell and battery designs; gaps in our knowledge; capabilities for understanding the hazards of thermal runaway and how to address them; how standard abuse tests may need to adapt to new challenges; and how research needs to support affected professionals, from pack designers to first responders, to manage hazards and ensure safe roll-out of next-generation cells into applications like electric vehicles (EVs). Finally, given the large number of next-generation technologies being explored, we encourage giving priority to safety-focused research in proportion to the rate of manufacturing scale-up of each specific technology.

25 ENERGY STORAGE↗

DOE OSTI2022

A distinct RNA recognition mechanism governs Np 4 decapping by RppH

Dinucleoside tetraphosphates, often described as alarmones because their cellular concentration increases in response to stress, have recently been shown to function in bacteria as precursors to nucleoside tetraphosphate (Np 4 ) RNA caps. Removal of this cap is critical for initiating 5' end-dependent degradation of those RNAs, potentially affecting bacterial adaptability to stress; however, the predominant Np 4 decapping enzyme in proteobacteria, ApaH, is inactivated by the very conditions of disulfide stress that enable Np 4 -capped RNAs to accumulate to high levels. Here, in this study, we show that, in Escherichia coli cells experiencing such stress, the RNA pyrophosphohydrolase RppH assumes a leading role in decapping those transcripts, preferring them as substrates over their triphosphorylated and diphosphorylated counterparts. Unexpectedly, this enzyme recognizes Np 4 -capped 5' ends by a mechanism distinct from the one it uses to recognize other 5' termini, resulting in a one-nucleotide shift in substrate specificity. The unique manner in which capped substrates of this kind bind to the active site of RppH positions the δ-phosphate, rather than the β-phosphate, for hydrolytic attack, generating triphosphorylated RNA as the primary product of decapping. Consequently, a second RppH-catalyzed deprotection step is required to produce the monophosphorylated 5' terminus needed to stimulate rapid RNA decay. The unconventional manner in which RppH recognizes Np 4 -capped 5' ends and its differential impact on the rates at which such termini are deprotected as a prelude to RNA degradation could have major consequences for reprogramming gene expression during disulfide stress.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

Towards a self-driving trigger at the LHC: adaptive response in real time

Real-time data filtering and selection—or trigger—systems at high-throughput scientific facilities such as the experiments at the Large Hadron Collider must process extremely high-rate data streams under stringent bandwidth, latency, and storage constraints. Yet these systems are typically designed as static, hand-tuned menus of selection criteria grounded in prior knowledge and simulation. In this work, we further explore the concept of a self-driving trigger, an autonomous data-filtering framework that reallocates resources and adjusts thresholds dynamically in real-time to optimize signal efficiency, rate stability, and computational cost as instrumentation and environmental conditions evolve. We introduce a benchmark ecosystem to emulate realistic collider scenarios and demonstrate real-time optimization of a menu including canonical energy sum triggers as well as modern anomaly-detection algorithms that target non-standard event topologies using machine learning. Using simulated data streams and publicly available collision data from the Compact Muon Solenoid experiment, we demonstrate the capability to dynamically and automatically optimize trigger performance under specific cost objectives without manual retuning. Our adaptive strategy shifts trigger design from static menus with heuristic tuning to intelligent, automated, data-driven control, unlocking greater flexibility and discovery potential in future high-energy physics analyses.

Emami, Shaghayegh [Michigan U.] (ORCID:00090007589↗

DOE OSTI2020

Dynamic Phasor Modeling of Various Multipulse Rectifiers and a VSI Fed by 18-Pulse Asymmetrical Autotransformer Rectifier Unit for Fast Transient Analysis

To study the fast modelling of dynamic characteristics caused by power electronic switching, the dynamic phasor (DP) theory based on the time-varying Fourier decomposition and frequency shifting is firstly applied to the modelling of various multipulse rectifiers. The DP model for symmetrical 12-pulse phase-shifting reactor rectifier unit (PSR-RU) is derived with model order reduction, relations between ac and dc terminals, and Taylor series expansion. The DP model of asymmetrical 18-pulse autotransformer rectifier unit (AT-RU) is proposed based on the switching functions expressed in the DP domain. Meanwhile, the DP model of voltage source inverter (VSI) fed by asymmetrical 18-pulse AT-RU is built with the harmonic state-space (HSS) equations. Under both balanced and unbalanced conditions, the good calculation accuracy and rapid simulation speed of the developed DP models are validated by the detailed time-domain (TD) simulation.

42 ENGINEERING↗

DOE OSTI2024

Production of Carbon Nanomaterials and Sorbents from Domestic U.S. Coal (Final Report)

The main goal of this project was to produce high-value carbon nanomaterials and carbon sorbents from domestic coal resources in a cost-effective manner. Four types of domestic coal samples were processed through a combination of deashing, devolatilization, oxidation, reduction, and activation treatments to produce graphene oxide (GO), reduced graphene oxide (RGO), and activated carbon (AC). The precursors and developed materials were extensively characterized by various methods to investigate the impact of the coal feedstock type on the yield and quality of each product. A commercial graphite-based GO sample was included in the experimental work as the baseline material for comparison with the coal-based materials developed in this work. The performed work also included a technoeconomic analysis and cost estimation for a plant processing 20 tons/day coal, a market evaluation for the graphene materials, and a technology gap analysis. A simple process by concentrated nitric acid oxidation is used to oxidize coal precursors for the production of GO. Fine oxidized coal particles that were separated from larger oxidized coal particles had significantly higher oxygen contents and were identified as coal-based GO samples. Coarse oxidized coal particles were used as precursors for production of AC. Based on the Raman spectroscopy results, coal-based GO samples exhibited G and D bands similar to those of graphite-based GO samples. X-ray photoelectron spectroscopy revealed that coal-based GO samples had surface oxygen contents of ~26-35% that were higher than the oxygen contents of graphite-based GO samples. Larger particles of oxidized coal samples were activated under different conditions to produce high surface area functionalized AC. Prepared materials had surface areas exceeding 1,500 m 2 /g and pore volumes more than 1 cm 3 /g with different pore size distributions. Reduced graphene oxide samples were prepared by thermal reduction of both coal-based and graphite-based GO samples at 170-2800 ºC. Coal-based and graphite-based RGO samples exhibited similar carbon contents, Raman spectra, and XRD profiles. Heat treatment above 1500 ºC shifted RGO to synthetic graphite. Among anthracite, bituminous, subbituminous, and lignite coals tested, anthracite was the best precursor to produce carbon nanomaterials exhibiting properties similar to those of graphite-based materials. Anthracite-based carbon nanomaterials also had the highest production yields. Technoeconomic analysis estimated the production cost of GO and RGO for anthracite-based samples at about 2,600 and 4,200 $/ton, respectively, which is about two orders of magnitude lower than the current estimated price of graphite-based materials. Several gaps to further develop the proposed technology were identified and discussed that include process and equipment optimization, process integration, need for additional bench- and pilot-scale experiments, and other items to reduce the scale up risk. Market analysis reports suggested a compound annual growth rate of 40% for graphene and related materials. Short-term applications include composites, inks, and coatings. However, energy storage applications appear to be the dominant potential long-term applications. Different applications of coal-based GO and RGO need to be explored and clear metrics and standards for each application need to be developed.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Pathways for Sustainable Reaction Kinetics in Li-CO2 Batteries

Lithium-carbon dioxide (Li-CO2) batteries hold great promise for high-energy-density storage applications. However, advancing this technology as a sustainable alternative to Li-ion systems requires a deeper understanding of the underlying reaction mechanisms, which remain elusive. A key challenge stems from the added complexity introduced by the presence of oxygen (O2) in CO2 environment. In this study, we employed a stable Cu3(VBi)0.5Se4 mid-entropy catalyst and conducted a comprehensive investigation to uncover the underlying reaction mechanisms in Li-CO2 batteries under varying CO2/O2 ratios. Under pure CO2 conditions, the battery exhibits excellent rechargeability, sustaining up to 1200 cycles. However, at high current densities, the discharge potential drops significantly (below 2.0 V), primarily due to sluggish reaction kinetics caused by solid carbon formation. Interestingly, introducing O2 mitigates this limitation, leading to a 58% increase of the discharge potential (from 1.7 V to 2.7 V) at the high current density of 0.8 mA/cm2, signifying a substantial boost in energy output. Our results reveal that the reactions follow distinct pathways, shifting from surface- to solution-based mechanism, and may even exhibit coexistence of both mechanisms, depending on the CO2/O2 ratio. These findings offer new insights for designing high-performance and sustainable Li-gas batteries utilizing CO2 and O2 mixtures.

Ngo, Anh [University of illinois Chicago]↗

DOE OSTI2021

Production of Biofuels from Biomass by Fungi

The use of abundantly available lignocellulosic biomass as a feedstock for biofuels has emerged as a sustainable alternative to fossil fuels. Industries across the world have shifted their focus to enhancing bioconversion through fungi, efficient and tractable organisms capable of producing valuable cost-effective enzymes. The many capabilities of fungal species offer opportunities for the tailored production of valuable compounds from a variety of substrates. This review details a high level examination of how fungal enzymes degrade plant polysaccharides to simple sugars through the sensitive coordination of transcription factors. Scientists have used a variety of tools like genetically engineering fungi, combining various species, and altering industrial/process conditions to enhance biomass deconstruction and fermentation while solving obstacles like inhibitory compounds. While ethanol and biodiesel are highlighted, additional biofuels are mentioned. These advances have uncovered themes like synergism and biocatalysis, led to the discovery of new fungal species, and revealed unique enzymatic mechanisms. Notably, this research highlights the complexity of metabolic systems within and between fungi. Fungi have been indispensable to the biofuel industry and future research will be crucial for energy sustainability.

Ottum, Eva MN↗

DOE OSTI2021

Effect of CO 2 -brine-rock reactions on pore architecture and permeability in dolostone: Implications for CO 2 storage and EOR

Geologic carbon sequestration (GCS) is considered a feasible technology for storing substantive volumes of greenhouse gases in subsurface geological formations. In the reservoir, far from carbon dioxide (CO 2 ) injection wells or in post-injection scenarios, diffusion dominates over advection. This condition conjoins with spatially distributed geochemical reactions to induce heterogeneous changes in pore architecture, i.e. pore body and throat sizes or surface roughness. These changes can affect CO 2 transport properties and storage capacity. In this work, we investigated mineral dissolution and precipitation in dolomite samples saturated with a CO 2 -saturated brine at 93 °C and 34.5 MPa, aged without flow. Two rock types samples, i.e. intergranular- and vuggy-dominant, were selected to investigate changes in pore size, porosity and permeability under reactive conditions. Mineral dissolution and precipitation were characterized using scanning electron microscopy. Changes in pore size were quantified via time-domain nuclear magnetic resonance (TD-NMR) transverse relaxation time (T 2 ) and diffusion coefficient (D) distributions. We show that mineral dissolution likely occurs in highly permeable pathways. These observations are confirmed through analysis of (T 2 ) and diffusion coefficient (D) distributions. In contrast to results during CO 2 -enriched brine continuous injection, mineral precipitation was observed in micropores. The leftward shift of the T 2 peaks, corresponding to micropores, also evidenced mineral precipitation in lowpermeability zones. However, microscale alterations resulted only in a subtle increase in porosity and permeability. Results in this study shed light on effects of geochemical reactions on alteration of rock properties in diffusion-dominated regions during CO 2 storage.

58 GEOSCIENCES↗

DOE OSTI2023

Simulation Based Inference with Domain Adaptation for Strong Gravitational Lensing

Simulation based inference leverages machine learning to carry out Bayesian inference for systems with intractable likelihoods. However, transitioning a network trained on simulated data to real data runs the risk of encountering domain shift, leading to performance losses. We attempt to implement domain adaptation into the sbi neural posterior estimation framework using the Maximum Mean Discrepancy as an additional network loss. We test two network architectures and use masked autoregressive flow for density estimation. We test the network on a set of 400,000 simulated strong gravitational lensing images generated using deeplenstronomy. The source domain is defined as low noise whereas the target domain has a noise profile sampled from experimentally derived DES survey conditions. We find that, while DA does lead to performance improvements, they are marginal at ~6% less inference error. We also find a similar marginal improvement in uncertainty calibration at around 8%.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2025

Initial Conditions of Planet Formation: Time Constraints from Small Bodies and the Lifetime of Reservoirs in the Solar Protoplanetary Disk

This review explores the timescales of the initial phase of planet formation, from nebular dust (CAIs and chondrules) to planetesimal accretion and differentiation, using evidence from meteorite research. Aluminium-Mg systematics of CAIs indicate either an extended period of CAI formation (∼0.3 Ma) or an initial 26 Al heterogeneity, with evidence supporting a homogeneous 26 Al abundance in the protoplanetary disk. Thermal and aqueous alteration on the parent body can disturb the U-Pb and Al-Mg chronometers in chondrules. Focusing on relatively robust isochron data from plagioclase of pristine (types ≤3.05) chondrites indicates a shift in chondrule formation locations, moving from the inner to the outer disk over time. Ages of basaltic achondrites show that silicate differentiation on small bodies was well underway within the first few million years (Ma) of our solar system. Their age record, however, reveals inconsistencies between different chronometers, partly caused by (i) secondary disturbances due to thermal metamorphism, aqueous alteration, or impacts, (ii) the presence of xenolithic minerals, and (iii) potentially variable initial 26 Al abundances due to disturbances at the mineral scale. Nucleosynthetic isotope data indicate that parent bodies of iron and stony meteorites formed in two distinct regions within the protoplanetary disk: the inner, non-carbonaceous (NC) and the outer, carbonaceous (CC) region. Based on Hf-W chronometry it has been demonstrated that NC and CC parent bodies of magmatic iron meteorites segregated their cores within ∼1–3 Ma after CAI formation, implying that parent body accretion occurred within <1 Ma in both reservoirs. Combining accretion ages with nucleosynthetic data further reveals that, at first order, NC and CC reservoirs in the solar protoplanetary disk were established within 1 Ma and existed over several Ma with limited exchange between them. In the CR chondrite accretion region of the disk, planetary bodies formed over at least 3 Ma, while in most other regions, formation spanned at least 1 Ma, with minimal changes in nucleosynthetic isotope compositions. Aerodynamical size sorting of dust likely introduced or amplified some of these variations.

26Al distribution↗