Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “component model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Model Development for Multi-Component Fuel Vaporization and Flash Boiling

The objectives of this project are to improve the multi-component fuel droplet and film vaporization models used in internal combustion engine simulation, and to develop a comprehensive model to predict the characteristics of multi-component flash boiling spray. This work explores two approaches to fuel composition treatment for modeling multi-component fuel vaporization: one based on discretization and surrogates, and the other based on continuous thermodynamic distribution of fuel properties. The experimental data collected for model validation are done under three fuel form factors: droplet, spray, and thin film. The study on sprays also include experimentation under non-flash and flash boiling conditions, a phenomenon that enhances fuel vaporization. The main goals of this work are: Design and develop a multi-component fuel droplet and wall film vaporization model using both discrete and continuous thermodynamics methods. Design and develop an analytical model for multi-component flash boiling. Integrate the multi-component droplet and film model into multi-dimensional engine calculations to predict the fuel vaporization process under engine operation condition. Conduct multi-component droplet and fuel film vaporization experiments in a non-combusting chamber to verify the proposed vaporization models. Characterize flash boiling phenomena of multi-component fuel sprays by optical and laser diagnostic techniques. This report will detail the experimental setup and the numerical basis for developing a model to achieve the main goals listed above. Key features of observed multi-component fuel vaporization will be summarized at the end of each experimental sections, and corresponding model performance evaluation will be presented at the end of each model development section.

33 ADVANCED PROPULSION SYSTEMS↗

Comparison and Assessment of Three Advanced Land Surface Models in Simulating Terrestrial Water Storage Components over the United States

In preparation for next generation North American Land Data Assimilation System (NLDAS), 3 three advanced land surface models (CLM4.0, Noah-MP, and CLSM-F2.5) were run from 1979 4 to 2014 within the NLDAS-based framework. Monthly total water storage anomaly (TWSA) and 5 its individual water storage components were evaluated against satellite-based and in situ 6 observations, and reference reanalysis products at basin-wide and statewide scales. In general, all 7 three models are able to reasonably capture the monthly and interannual variability and 8 magnitudes for TWSA. However, contributions of the anomalies of individual water 9 components to TWSA are very dependent on the model and basin. A major contributor to the 10 TWSA is the anomaly of total column soil moisture content (SMCA) for CLM4.0 and Noah-MP 11 or groundwater storage anomaly (GWSA) for CLSM-F2.5 although other components such as 12 the anomaly of snow water equivalent (SWEA) also play some role. For each individual water 13 storage component, the models are able to capture broad features such as monthly and 14 interannual variability. However, there are large inter-model differences and quantitative 15 uncertainties in this study. Therefore, it should be thought of as a preliminary synthesis and 16 analysis.

58 GEOSCIENCES↗

GALACTIC FOREGROUNDS: SPATIAL FLUCTUATIONS AND A PROCEDURE FOR REMOVAL

Present-day cosmic microwave background (CMB) studies require more accurate removal of the Galactic foreground emission. This removal becomes even more essential for CMB polarization measurements. In this paper, we consider a method for filtering out the diffuse Galactic fluctuations on the basis of their statistical properties, namely, the power-law spectra of fluctuations. We focus on the statistical properties of two major Galactic foregrounds that arise from magnetized turbulence, namely, the diffuse synchrotron emission and the thermal emission from dust, and describe how their power laws change with the Galactic latitude. We attribute this change to the change in the geometry of the emission region and claim that the universality of the turbulence spectrum provides a new way of removing Galactic foregrounds. For the Galactic synchrotron emission, we mainly focus on the geometry of the synchrotron emitting regions, which will provide useful information for future polarized synchrotron emission studies. Our model calculation suggests that either a one-component extended halo model or a two-component model, an extended halo component (scale height {approx}>1 kpc) plus a local component, can explain the observed angular spectrum of the synchrotron emission. For thermal emission from Galactic dust, we discuss general properties of a publicly available 94 GHz total dust emission map and explain how we can obtain a polarized dust emission map. Based on a simple model calculation, we obtain the angular spectrum of the polarized dust emission. Our model calculation suggests that C{sub l} {proportional_to} l {sup -11/3} for l {approx}> 1000 and a shallower spectrum for l {approx}< 1000. We discuss and demonstrate how we can make use of our findings to remove Galactic foregrounds using a template of spatial fluctuations. In particular, we consider examples of spatial filtering of a foreground at small scales, when the separation into CMB signal and foregrounds is done at larger scales. We demonstrate that the new technique of spatial filtering of foregrounds may be promising for recovering the CMB signal in a situation where foregrounds are known at a scale different from the one being studied. It can also improve filtering by combining measurements obtained at different scales.

79 ASTRONOMY AND ASTROPHYSICS↗

Model Validation of Power System Components Using Hybrid Dynamic Simulation

Hybrid dynamic simulation, with its capability of injecting external signals into dynamic simulation, opens the traditional dynamic simulation loop for interaction with actual field measurements. This simulation technique enables rigorous comparison between simulation results and actual measurements and model validation of individual power system components within a small subsystem. This paper uses a real example of generator model validation to illustrate the procedure and validity of the component model validation methodology using hybrid dynamic simulation. Initial model calibration has also been carried out to show how model validation results would be used to improve component models

24 POWER TRANSMISSION AND DISTRIBUTION↗

Statistical tools for prognostics and health management of complex systems

Prognostics and Health Management (PHM) is increasingly important for understanding and managing today's complex systems. These systems are typically mission- or safety-critical, expensive to replace, and operate in environments where reliability and cost-effectiveness are a priority. We present background on PHM and a suite of applicable statistical tools and methods. Our primary focus is on predicting future states of the system (e.g., the probability of being operational at a future time, or the expected remaining system life) using heterogeneous data from a variety of sources. We discuss component reliability models incorporating physical understanding, condition measurements from sensors, and environmental covariates; system reliability models that allow prediction of system failure time distributions from component failure models; and the use of Bayesian techniques to incorporate expert judgments into component and system models.

42 ENGINEERING↗

Kinetic Modeling of Gasoline Surrogate Components and Mixtures under Engine Conditions

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, an improved version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multicomponent gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines (3-50 atm, 650-1200K, stoichiometric fuel/air mixtures). Simulation results are discussed focusing attention on the mixing effects of the fuel components.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Experiment attributes to establish tube with twisted tape insert performance cooling plasma facing components

The modeling capability for tubes with twisted tape inserts is reviewed with reference to the application of cooling plasma facing components in magnetic confinement fusion devices. The history of experiments examining the cooling performance of tubes with twisted tape inserts is reviewed with emphasis on the manner of heating, flow stability limits and the details of the test section and fluid delivery system. Models for heat transfer, burnout, and onset of net vapor generation in straight tube flows and tube with twisted tape are compared. As a result, the gaps in knowledge required to establish performance limits of the plasma facing components are identified and attributes of an experiment to close those gaps are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Probing Red Blood Cell Mechanics, Rheology and Dynamics with a Two-Component Multi-scale Model

This study is partially motivated by the validation of a new two-component multi-scale cell model we developed recently that treats the lipid bilayer and the cytoskeleton as two distinct components.Here, the whole cell model is validated and compared against several available experiments that examine red blood cell (RBC) mechanics, rheology and dynamics. First, we investigated RBC deformability in a microfluidic channel with a very small cross-sectional area and quantified the mechanical properties of the RBC membrane. Second, we simulated twisting torque cytometry and compared predicted rheological properties of the RBC membrane with experimental measurements. Finally, wemodelled the tank-treading (TT) motion of a RBC in a shear flow and explored the effect of channel width variation on the TT frequency. We also investigated the effects of bilayer–cytoskeletal interactions on these experiments and our simulations clearly indicated that they play key roles in the determination of cell membrane mechanical, rheological and dynamical properties. These simulations serve as validation tests and moreover reveal the capabilities and limitations of the new whole cell model.

Li, Xuejin↗

Vaporization modeling of petroleum-biofuel drops using a hybrid multi-component approach

Numerical modeling of the vaporization characteristics of multi-component fuel mixtures is performed in this study. The fuel mixtures studied include those of binary components, biodiesel, diesel-biodiesel, and gasoline-ethanol. The use of biofuels has become increasingly important for reasons of environmental sustainability. Biofuels are often blended with petroleum fuels, and the detailed understanding of the vaporization process is essential to designing a clean and efficient combustion system. In this study, a hybrid vaporization model is developed that uses continuous thermodynamics to describe petroleum fuels and discrete components to represent biofuels. The model is validated using the experimental data of n-heptane, n-heptane-n-decane mixture, and biodiesel. Since biodiesel properties are not universal due to the variation in feedstock, methods for predicting biodiesel properties based on the five dominant fatty acid components are introduced. Good levels of agreement in the predicted and measured drop size histories are obtained. Furthermore, in modeling the diesel-biodiesel drop, results show that the drop lifetime increases with the biodiesel concentration in the blend. During vaporization, only the lighter components of diesel fuel vaporize at the beginning. Biodiesel components do not vaporize until some time during the vaporization process. On the other hand, results of gasoline-ethanol drops indicate that both fuels start to vaporize once the process begins. At the beginning, the lighter components of gasoline have a slightly higher vaporization rate than ethanol. After a certain time, ethanol vaporizes faster than the remaining gasoline components. At the end, the drop reduces to a regular gasoline drop with heavier components. Overall, the drop lifetime increases as the concentration of ethanol increases in the drop due to the higher latent heat. (author)

02 PETROLEUM↗

PORFLOW Implementation of Vadose Zone Conceptual Model for Naval Reactor Component Disposal Area in the E-Area Low Level Waste Facility Performance Assessment

PORFLOW models have been developed to implement the proposed conceptual models for the two Naval Reactor Component Disposal Areas (NRCDAs), 643-7E and 643-26E, for the purpose of evaluating dose impacts and producing disposal limits for the E-Area Low-Level Facility (LLWF). New NRCDA conceptual models were proposed by Wohlwend and Butcher (2019) for two areas within/adjacent to the E-Area LLWF used as storage/disposal sites for reactor components from the U.S. Navy since 1987. Naval Reactor (NR) waste is comprised of highly radioactive components consisting of activated corrosion-resistant metal alloy contained within welded thick-walled steel casks, and auxiliary equipment primarily contaminated with lower levels of Activated Corrosion Products (ACPs) residing on the metal surfaces and contained within thinner-walled bolted containers.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

PORFLOW Implementation of Vadose Zone Conceptual Model for Naval Reactor Component Disposal Areas in the E-Area Low Level Waste Facility Performance Assessment

PORFLOW models have been developed to implement the proposed conceptual models for the two Naval Reactor Component Disposal Areas (NRCDAs), 643-7E and 643-26E, for the purpose of evaluating dose impacts and producing disposal limits for the E-Area Low-Level Facility (LLWF). New NRCDA conceptual models were proposed by Wohlwend and Butcher (2019) for two areas within/adjacent to the E-Area LLWF used as storage/disposal sites for reactor components from the U.S. Navy since 1987. Naval Reactor (NR) waste is comprised of highly radioactive components consisting of activated corrosion-resistant metal alloy contained within welded thick-walled steel casks, and auxiliary equipment primarily contaminated with lower levels of Activated Corrosion Products (ACPs) residing on the metal surfaces and contained within thinner-walled bolted containers.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Evolution of the X-ray properties of the transient magnetar XTE J1810–197

We report on X-ray observations of the 5.54 s transient magnetar XTE J1810–197 using the XMM-Newton and Chandra observatories, analyzing new data from 2008 through 2014, and re-analyzing data from 2003 through 2007 with the benefit of these six years of new data. From the discovery of XTE J1810–197 during its 2003 outburst to the most recent 2014 observations, its 0.3–10 keV X-ray flux has declined by a factor of about 50 from 4.1 × 10{sup −11} to 8.1 × 10{sup −13} erg cm{sup −2} s{sup −1}. Its X-ray spectrum has now reached a steady state. Pulsations continue to be detected from a 0.3 keV thermal hot spot that remains on the neutron star (NS) surface. The luminosity of this hot spot exceeds XTE J1810–197’s spin-down luminosity, indicating continuing magnetar activity. We find that XTE J1810–197’s X-ray spectrum is best described by a multiple component blackbody model in which the coldest 0.14 keV component likely originates from the entire NS surface, and the thermal hot-spot is, at different epochs, well described by an either one- or two-component blackbody model. A 1.2 keV absorption line, possibly due to resonant proton scattering, is detected at all epochs. The X-ray flux of the hot spot decreased by ≈20% between 2008 and 2009 March, the same period during which XTE J1810–197 became radio quiet.

79 ASTRONOMY AND ASTROPHYSICS↗

Design and Implementation of Scientific Software Components to Enable Multiscale Modeling: The Effective Fragment Potential (QM/EFP) Method

The design and development of scientific software components to provide an interface to the effective fragment potential (EFP) methods are reported. Multiscale modeling of physical and chemical phenomena demands the merging of software packages developed by research groups in significantly different fields. Componentization offers an efficient way to realize new high performance scientific methods by combining the best models available in different software packages without a need for package readaptation after the initial componentization is complete. The EFP method is an efficient electronic structure theory based model potential that is suitable for predictive modeling of intermolecular interactions in large molecular systems, such as liquids, proteins, atmospheric aerosols, and nanoparticles, with an accuracy that is comparable to that of correlated ab initio methods. The developed components make the EFP functionality accessible for any scientific component-aware software package. The performance of the component is demonstrated on a protein interaction model, and its accuracy is compared with results obtained with coupled cluster methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

THE X-RAY SPECTRA OF THE LUMINOUS LMXBs IN NGC 3379: FIELD AND GLOBULAR CLUSTER SOURCES

From a deep multi-epoch Chandra observation of the elliptical galaxy NGC 3379 we report the spectral properties of eight luminous LMXBs (L{sub X} >1.2 x 10{sup 38} erg s{sup -1}). We also present a set of spectral simulations, produced to aid the interpretation of low-count single-component spectral modeling. These simulations demonstrate that it is possible to infer the spectral states of X-ray binaries from these simple models and thereby constrain the properties of the source. Of the eight LMXBs studied, three reside within globular clusters (GCs) and one is a confirmed field source. Due to the nature of the luminosity cut, all sources are either neutron star (NS) binaries emitting at or above the Eddington luminosity or black hole (BH) binaries. The spectra from these sources are well described by single-component models, with parameters consistent with Galactic LMXB observations, where hard-state sources have a range in photon index of 1.5-1.9 and thermally dominant (TD) sources have inner-disk temperatures between {approx}0.7and1.55 keV. The large variability observed in the brightest GC source (L{sub X} >4 x 10{sup 38} erg s{sup -1}) suggests the presence of a BH binary. At its most luminous this source is observed in a TD state with kT{sub in} = 1.5 keV, consistent with a BH mass of {approx}4 M{sub sun}. This observation provides further evidence that GCs are able to retain such massive binaries. We also observed a source transitioning from a bright state (L{sub X} {approx}1 x 10{sup 39} erg s{sup -1}), with prominent thermal and non-thermal components, to a less luminous hard state (L{sub X} = 3.8 x 10{sup 38} erg s{sup -1}, {Gamma}= 1.85). In its high flux emission, this source exhibits a cool-disk component of {approx}0.14 keV, similar to spectra observed in some ultraluminous X-ray sources (ULXs). Such a similarity indicates a possible link between 'normal' stellar-mass BHs in a high accretion state and ULXs.

79 ASTRONOMY AND ASTROPHYSICS↗

Geothermal Operational Optimization with Machine Learning

The Geothermal Operational Optimization with Machine Learning (GOOML) project has developed a generic and extensible component-based system modeling framework to study complex geothermal fields using a data-driven approach. Through building a digital twin of a geothermal steam field with the GOOML modeling framework, operators can analyze historical and forecasted power production, explore possible steam field configurations, and optimize real world operations, all in a cost-effective digital environment. The GOOML modeling software is based on a historical data-assimilation framework that uses first-principal thermodynamics to model steam field components using historical data, and a forecast framework that uses machine-learning-driven models of steam field components to predict future operations. This modeling framework creates countless new opportunities for digital exploration of steam field design and operations. To date, digital twins have been developed for several steam fields in New Zealand and the United States. These digital twins have been validated by comparing hindcast predictions against historical production data. Field design and operations have been explored using genetic optimization and reinforcement learning. Initial results show compelling and often surprising opportunities for improved design and operation of fields with 2 to 5 percent improvements in annual energy production. GOOML is driving a step-change in geothermal operations by applying state-of-the-art machine learning algorithms, comprehensive data analytics, and a first-of-its-kind intelligent geothermal systems model.

40 EE - Geothermal Technologies Office (EE-4G)↗

Direct measurements of dust attenuation in z ∼ 1.5 star-forming galaxies from 3D-HST: Implications for dust geometry and star formation rates

The nature of dust in distant galaxies is not well understood, and until recently few direct dust measurements have been possible. We investigate dust in distant star-forming galaxies using near-infrared grism spectra of the 3D-HST survey combined with archival multi-wavelength photometry. These data allow us to make a direct comparison between dust around star-forming regions (A {sub V,} {sub H} {sub II}) and the integrated dust content (A {sub V,} {sub star}). We select a sample of 163 galaxies between 1.36 ≤ z ≤ 1.5 with Hα signal-to-noise ratio ≥5 and measure Balmer decrements from stacked spectra to calculate A {sub V,} {sub H} {sub II}. First, we stack spectra in bins of A {sub V,} {sub star}, and find that A {sub V,} {sub H} {sub II} = 1.86 A {sub V,} {sub star}, with a significance of σ = 1.7. Our result is consistent with the two-component dust model, in which galaxies contain both diffuse and stellar birth cloud dust. Next, we stack spectra in bins of specific star formation rate (log SSFR), star formation rate (log SFR), and stellar mass (log M {sub *}). We find that on average A {sub V,} {sub H} {sub II} increases with SFR and mass, but decreases with increasing SSFR. Interestingly, the data hint that the amount of extra attenuation decreases with increasing SSFR. This trend is expected from the two-component model, as the extra attenuation will increase once older stars outside the star-forming regions become more dominant in the galaxy spectrum. Finally, using Balmer decrements we derive dust-corrected Hα SFRs, and find that stellar population modeling produces incorrect SFRs if rapidly declining star formation histories are included in the explored parameter space.

79 ASTRONOMY AND ASTROPHYSICS↗

Numerical simulation of the beam self-cleaning process in a multimode graded-index fibre during propagation of a pump wave and a Stokes component

A model of coupled modes is proposed, which makes it possible to describe the propagation of a pump wave and a Stokes component in a multimode graded-index fibre. A decrease in the depression in the centre of the profile of the pump wave intensity distribution as a result of the influence of Kerr effects and random linear coupling of modes is demonstrated. (paper)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

High Cost/High Risk Components to Chalcogenide Molded Lens Model: Molding Preforms and Mold Technology

FiveFocal outlined the major components to a cost model for isothermal compression molding of chalcogenide lenses in view of alternative methods of fabrication, such as single point diamond turning (SPDT) or conventional grinding and polishing. There is certainly a threshold for lens production volume that self-selects molding over SPDT or grinding/polishing, and it is the aim of the FiveFocal model to determine this inflection point. Of the many components of the cost model, two main items are those concerning lens preforms and molding tooling technology. These two areas are the focus of the remainder of this document.

Chalcogenide Lens Molding↗