Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Mechanical Testing of Carbon Based Woven Thermal Protection Materials

Three Dimensional Woven thermal protection system (TPS) materials are one of the enabling technologies for mechanically deployable hypersonic decelerator systems. These materials have been shown capable of serving a dual purpose as TPS and as structural load bearing members during entry and descent operations. In order to ensure successful structural performance, it is important to characterize the mechanical properties of these materials prior to and post exposure to entry-like heating conditions. This research focuses on the changes in load bearing capacity of woven TPS materials after being subjected to arcjet simulations of entry heating. Preliminary testing of arcjet tested materials [1] has shown a mechanical degradation. However, their residual strength is significantly more than the requirements for a mission to Venus [2]. A systematic investigation at the macro and microstructural scales is reported here to explore the potential causes of this degradation. The effects of heating on the sizing (an epoxy resin coating used to reduce friction and wear during fiber handling) are discussed as one of the possible causes for the decrease in mechanical properties. This investigation also provides valuable guidelines for margin policies for future mechanically deployable entry systems.

Pham, John↗
NASA NTRS2016

Post-Test Inspection of NASA's Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge Chamber

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 hours of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for the discharge chamber as well as other miscellaneous components such as the high-voltage propellant isolators and electrical cabling. Comparison of magnetic field measurements taken during pretest and post-test inspections indicate that the field strength did not degrade, consistent with performance data obtained during the test. Inspection of discharge chamber mesh samples show a deposition coating primarily composed of grid material that is approximately 15 micrometers in thickness. This thickness is well within the retention capability of the mesh and is therefore not expected to present any issues. Approximately 3.1 grams of deposition flakes were found at the bottom of the discharge chamber, composed primarily of grid material and carbon. Calculated size histograms of these flakes indicate that 99% have a maximum dimension of 200 micrometers or smaller, which is significantly less than the ion optics grid gap. Larger flakes that are capable of causing a grid-to-grid short will be analyzed to determine if their formation will occur in flight or is a facility effect. The high-voltage propellant isolators as well as numerous other electrical insulators were inspected and no evidence of arcing or any other issues were found.

Electric Propulsion↗
NASA NTRS2017

A Comparison of the SOCIT and DebriSat Experiments

This paper explores the differences between, and shares the lessons learned from, two hypervelocity impact experiments critical to the update of Department of Defense (DOD) and National Aeronautics and Space Administration (NASA) satellite breakup models. The procedures as well as the processes of the fourth Satellite Orbital Debris Characterization Impact Test (SOCIT4) were analyzed and related to the ongoing DebriSat experiment. SOCIT4 accounted for about 90% of the entire satellite mass, but only analyzed approximately 59% with a total of approximately 4,700 fragments. DebriSat aims to recover and analyze 90% of the initial mass and to do so, fragments with at least a longest dimension of 2 mm are collected and processed. DebriSat's use of modern materials, especially carbon fiber, significantly increases the fragment count and to date, there are over 126,000 fragments collected. Challenges, such as procedures and human inputs, encountered throughout the DebriSat experiment are also shared. While, SOCIT4 laid the foundation for the majority of DebriSat processes, the technological advancements since SOCIT4 allow for more accurate, rigorous, and in-depth, procedures that will aid the update of satellite breakup models.

Ausay, E.↗
NASA NTRS2018

Organic Biomarker-Based Assays to Evaluate Total Bioburden and Organic Compounds on Space Flight Hardware

Meeting planetary protection (PP) requirements for space flight hardware may involve bioburden reduction by dry heat microbial reduction (DHMR). The NASA standard assay to demonstrate the reduction of organisms involves the swabbing of surfaces, heat shock of the extracted samples, plating of the samples on Trypticase Soy Agar (TSA), and counting colony forming units after an incubation period. The standard assay uses enumeration of heat tolerant spore-formers as a proxy for total bioburden and is generally expected to provide a lower limit. We suggest that a better estimate of the total bioburden could be obtained through sampling and analysis of organic biomarkers. As biological organisms are fundamentally organic in chemistry (i.e. carbon containing materials) it is important to characterize the biomarker compounds that are released from organisms that 1) exist on flight hardware before microbial reduction and 2) left behind from the killed organisms following microbial reduction.

Locke, Darren R.↗
NASA NTRS2019

Buckling Testing and Analysis of Honeycomb Sandwich Panel Arc Segments of a Full-Scale Fairing Barrel Part 4: Six-ply Out-of-Autoclave Facesheets

Four honeycomb sandwich panel types, representing 1/16th arc segments of a 10-m diameter barrel section of the Heavy Lift Launch Vehicle (HLLV), were manufactured and tested under the NASA Composites for Exploration program and the NASA Constellation Ares V program. Two configurations were chosen for the panels: 6-ply facesheets with 1.125 in. honeycomb core and 8-ply facesheets with 1.000 in. honeycomb core. Additionally, two separate carbon fiber/epoxy material systems were chosen for the facesheets: in-autoclave IM7/977-3 and out-of-autoclave T40-800b/5320-1. Smaller 3 ft. by 5 ft. panels were cut from the 1/16th barrel sections. These panels were tested under compressive loading at the NASA Langley Research Center (LaRC). Furthermore, linear eigenvalue and geometrically nonlinear finite element analyses were performed to predict the compressive response of each 3 ft. by 5 ft. panel. This manuscript summarizes the experimental and analytical modeling efforts pertaining to the panels composed of 6-ply, T40-800b/5320-1 facesheets (referred to as Panels D). To improve the robustness of the geometrically nonlinear finite element model, measured surface imperfections were included in the geometry of the model. Both the linear and nonlinear models yield good qualitative and quantitative predictions. Additionally, it was correctly predicted that the panel would fail in buckling prior to failing in strength. Furthermore, three-dimensional (3D) effects on the compressive response of the panel were studied.

David E Myers↗
NASA NTRS2021

Post-test Inspection of NASA’s Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge Chamber

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014after demonstrating 51,184 hours of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for the discharge chamber as well as other miscellaneous components such as the high-voltage propellant isolators and electrical cabling. Comparison of magnetic field measurements taken during pretest and post-test inspections indicate that the field strength did not degrade, consistent with performance data obtained during the test. Inspection of discharge chamber mesh samples show a deposition coating primarily composed of grid material that is approximately 15 μm in thickness. This thickness is well within the retention capability of the mesh and is therefore not expected to present any issues. Approximately 3.1 grams of deposition flakes were found at the bottom of the discharge chamber, composed primarily of grid material and carbon. Calculated size histograms of these flakes indicate that 99% have a maximum dimension of 200 μm or smaller, which is significantly less than the ion optics grid gap. Larger flakes that are capable of causing a grid-to-grid short will be analyzed to determine if their formation will occur in flight or is a facility effect. The high-voltage propellant isolators as well as numerous other electrical insulators were inspected and no evidence of arcing or any other issues were found.

Rohit Shastry↗
NASA NTRSDate not supplied

OVIRS Visible to Near-IR Spectral Results at (101955) Bennu

The OSIRIS-REx Visible and InfraRed Spectrometer (OVIRS) operates over a wavelength range of ~0.4 to 4.3 μm with a 4-mrad field of view.During the OSIRIS-REx mission, OVIRS collected more than 500,000 spectra of Bennu for spectral characterization of the surface. Constant phase angle observations were dedicated to global mapping at ~20 m resolution. Data with higher resolution (2–4 m) were obtained of the candidate sample sites. We analyzed low-phase-angle (12:30 pm local solar time) global data for surface color trends, surface temperatures, and the band depths of absorption features associated with hydrated minerals, carbon-bearing materials, iron oxides, and pyroxenes.

A.A. Simon↗
NASA NTRSDate not supplied

MEDLI2: Ablator Models for Flight

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating[1,2]. Discrepancies between MEDLI’s flight heating data and predicted thermal response and recession[3] led to a campaign to characterize and test Mars2020 and MEDLI2 (Mars Entry, Descent, and Landing Instrument 2)[4] flight-lot thermal protection materials (TPS) at relevant ground test conditions. This paper covers the development and validation of flight-lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material SLA-561V (Super Lightweight Ablator). Virgin and char properties such as thermal conductivity and emissivity were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties were characterized and determined to be similar to prior TPS material measurements used for the heritage models. MEDLI2 also investigated the impact of the protective coating that was applied to MSL and Mars2020’s PICA heatshield to reduce the particulate matter shedding. Evidence from arc jet experiments on coated PICA showed that although there were no adverse effects on the performance of the TPS, there were differences in the in-depth temperatures and reduced recession compared to material response predictions of uncoated PICA.[5,6]. Fully Implicit Ablation and Thermal response (FIAT)[7] material response simulations were conducted with the heritage and MEDLI2 flight-lot material models. FIAT-predicted in-depth temperature responses and recession predictions were compared to flight-lot certification ground-test arc jet test data and MEDLI2 thermocouple data.

Materials Response↗
NASA NTRS2021

Pluto’s Sputnik Planitia: Composition of geological units from infrared spectroscopy

We have compared spectroscopic data of Sputnik Planitia on Pluto, as acquired by New Horizons’ Linear Etalon Imaging Spectral Array (LEISA) instrument, to the geomorphology as mapped by White et al. (2017) using visible and panchromatic imaging acquired by the LOng-Range Reconnaissance Imager (LORRI) and the Multi-spectral Visible Imaging Camera (MVIC). We have focused on 13 of the geologic units identified by White et al. (2017), which include the plains and mountain units contained within the Sputnik basin. We divided the map of Sputnik Planitia into 15 provinces, each containing one or more geologic units, and we use LEISA to calculate the average spectra of the units inside the 15 provinces. Hapke-based modeling was then applied to the average spectra of the units to infer their surface composition, and to determine if the composition resulting from the modeling of LEISA spectra reflects the geomorphologic analyses of LORRI data, and if areas classified as being the same geologically, but which are geographically separated, share a similar composition. We investigated the spatial distribution of the most abundant ices on Pluto’s surface - CH4, N2, CO, H2O, and a non-ice component presumed to be a macromolecular carbon-rich material, termed a tholin, that imparts a positive spectral slope in the visible spectral region and a negative spectral slope longward of ~1.1 μm. Because the exact nature of the non-ice component is still debated and because the negative spectral slope of the available tholins in the near infrared does not perfectly match the Pluto data, for spectral modeling purposes we reference it generically as the negative spectral slope endmember (NSS endmember). We created maps of variations in the integrated band depth (from LEISA data) and areal mass fraction (from the modeling) of the components. The analysis of correlations between the occurrences of the endmembers in the geologic units led to the observation of an anomalous suppression of the strong CH4 absorption bands in units with compositions that are dominated by H2O ice and the NSS endmember. Exploring the mutual variation of the CH4 and N2 integrated band depths with the abundance of crystalline H2O and NSS endmember revealed that the NSS endmember is primarily responsible for the suppression of CH4 absorptions in mountainous units located along the western edge of Sputnik Planitia. Our spectroscopic analyses have provided additional insight into the geological processes that have shaped Sputnik Planitia. A general increase in volatile abundance from the north to the south of Sputnik Planitia is observed. Such an increase first observed and interpreted by Protopapa et al., 2017 and later confirmed by climate modeling (Bertrand et al., 2018) is expressed geomorphologically in the form of preferential deposition of N2 ice in the upland and mountainous regions bordering the plains of southern Sputnik Planitia. Relatively high amounts of pure CH4 are seen at the southern Tenzing Montes, which are a natural site for CH4 deposition owing to their great elevation and the lower insolation they are presently receiving. The NSS endmember correlates the existence of tholins within certain units, mostly those coating the low-latitude mountain ranges that are co-latitudinal with the tholin-covered Cthulhu Macula. The spectral analysis has also revealed compositional differences between the handful of occurrences of northern non-cellular plains and the surrounding cellular plains, all of which are located within the portion of Sputnik Planitia that is presently experiencing net sublimation of volatiles, and which do not therefore exhibit a surface layer of bright, freshly-deposited N2 ice. The compositional differences between the cellular and non-cellular plains here hint at the effectiveness of convection in entraining and trapping tholins within the body of the cellular plains, while preventing the spread of such tholins to abutting non-cellular plains.

Pluto's Sputnik Planitia↗
NASA NTRSDate not supplied

MEDLI2 Material Response Model Development and Validation

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating and temperatures. Discrepancies between MEDLI’s recorded in-depth heating data and the predicted thermal response and recession led to a campaign to characterize and test Mars Entry, Descent, and Landing Instrument 2 (MEDLI2) flight lot thermal protection materials (TPS) at relevant temperatures and pressures for Martian entry conditions. This paper covers the development and validation of MEDLI2 flight lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material Super-Lightweight Ablator (SLA-561V). Virgin and char thermal conductivities were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties such as virgin and char density, emissivity, absorptivity, and specific heat capacitance was also characterized and compared to the “Heritage” models used during the TPS design phase of Mars 2020. Fully Implicit Ablation and Thermal response (FIAT) simulations were completed using the Heritage and MEDLI2 material response models to provide evidence of the increased accuracy of the MEDLI2 model. FIAT predicted in-depth temperatures were compared to flight lot certification ground-test arc jet test data and MEDLI2 flight thermocouple data.

Material response↗
NASA NTRSDate not supplied

Development of Additive Manufacturing Technologies for 3D Printing of Spacecraft Heat Shields

Introduction: Ablative heat shields are an enabling technology for entry into planetary atmospheres. From the PICA heatshields used for several Mars rovers to the carbon phenolic material used for Galileo’s Jupiter entry probe, the heat shield manages the heat load transferred to the payload, protecting the sensitive scientific instruments carried on entry probes. The Additive Manufacturing of Thermal Protection Systems (AMTPS) project, an Early Career Initiative (ECI) funded by NASA’s Space Technology Mission Directorate and led by NASA Johnson Space Center, seeks to develop materials and processes for 3D printing ablative heat shields for spacecraft. Current methods for producing ablative heat shields are extremely labor intensive and re-quire extensive hands-on processes and quality control characterization. Additive manufacturing (AM) offers the possibility of reduced production times, improved reliability, and enhanced performance via graded compositions. Costs will also be reduced by reducing the time and labor required for heat shield production. Direct integration of the heat shield onto the structure during processing simplifies integration and reduces risk. Material Development: A critical challenge for the project is development of a material system that can (1) be printed in a near-net shape process and (2) perform well as an ablator. Achieving printability requires the material to flow under applied pressure, but maintain its shape once extruded from the printer nozzle. Ablative performance is measured by a multitude of markers, including char yield, char strength, thermal conductivity, and recession rate. Furthermore, there are several mechanical and thermal property considerations for vehicle integration including coefficient of thermal expansion (CTE) and residual stress. AM technology will be leveraged to grade the material formulation and properties through the thickness of the heat shield, an architecture not possible with current manufacturing processes. To this end, “robust” material formulations have been pre-pared with higher density for use on the surface where most ablation will occur. “Insulative” material formulations, with lower density and lower thermal conductivity, are prepared for use in the depth of the heat shield. This graded architecture will re-duce the overall mass of the heat shield and reduce costs and/or increase scientific payload capacities. To achieve a material system with the required properties, multiple resins have been investigated in collaboration with NASA Ames Research Center. To tune printability and performance, resin additives were studied to improve flexibility of the cured material while maintaining acceptable ablative performance. Material coupons were printed and studied via a suite of mechanical and thermal characterization methods. Arc jet testing was conducted at NASA Ames Research Center to evaluate ablative performance and thermal protection under conditions expected in atmospheric entry. Manufacturing Scale-Up: A partnership with Oak Ridge National Laboratory (ORNL) aims to enable full-scale fabrication of a 3D printed heat shield. Leveraging expertise in manufacturing and 3D printing at ORNL, a mid-scale manufacturing demonstration unit will be built and tested, using a dual-layer ablative system printed directly onto the titanium structure. Work on robotic system integration is ongoing and efforts to scale up material mixing with a material compound will ensure accurate and homogenous composition. Flight Test: A hypersonic sub-orbital flight test will provide a rigorous test of material performance ranging from ablation, thermal management, and mechanical integrity. Design of the capsule has taken place in collaboration with the University of Kentucky. Data collected from the flight will inform future design efforts in material formulation, printing methodology, and heat shield-capsule integration.

additive manufacturing↗
NASA NTRSDate not supplied

Development of Additive Manufacturing Technologies for 3D Printing of Spacecraft Heat Shields

Ablative heat shields are an enabling technology for entry into planetary atmospheres. From the PICA heatshields used for several Mars rovers to the carbon phenolic material used for Galileo’s Jupiter entry probe, the heat shield manages the heat load transferred to the payload, protecting the sensitive scientific instruments carried on entry probes. The Additive Manufacturing of Thermal Protection Systems (AMTPS) project, an Early Career Initiative (ECI) funded by NASA’s Space Technology Mission Directorate and led by NASA Johnson Space Center, seeks to develop materials and processes for 3D printing ablative heat shields for spacecraft. Current methods for producing ablative heat shields are extremely labor intensive and require extensive hands-on processes and quality control characterization. Additive manufacturing (AM) offers the possibility of reduced production times, improved reliability, and enhanced performance via graded compositions. Costs will also be reduced by reducing the time and labor required for heat shield production. Direct integration of the heat shield onto the structure during processing simplifies integration and reduces risk.

Nathaniel Olson↗
NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Composite manufacturing↗
NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Automated Fiber Placement↗
NASA NTRSDate not supplied

Development of Additive Manufacturing Technologies for 3D Printing of Spacecraft Heat Shields

Ablative heat shields are an enabling technology for entry into planetary atmospheres. From the PICA heatshields used for several Mars rovers to the carbon phenolic material used for Galileo’s Jupiter entry probe, the heat shield manages the heat load transferred to the payload, protecting the sensitive scientific instruments carried on entry probes. The Additive Manufacturing of Thermal Protection Systems (AMTPS) project, an Early Career Initiative (ECI) funded by NASA’s Space Technology Mission Directorate and led by NASA Johnson Space Center, seeks to develop materials and processes for 3D printing ablative heat shields for spacecraft. Current methods for producing ablative heat shields are extremely labor intensive and require extensive hands-on processes and quality control characterization. Additive manufacturing (AM) offers the possibility of reduced production times, improved reliability, and enhanced performance via graded compositions. Costs will also be reduced by reducing the time and labor required for heat shield production. Direct integration of the heat shield onto the structure during processing simplifies integration and reduces risk.

Nathaniel Olson↗
NASA NTRS2026

The NASA OSIRIS-REx Sample Catalog: Samples Returned from Investigators

OSIRIS-REx is a sample return mission that collected carbon-rich material from B-type asteroid Bennu. After landing on September 24th, 2023, the science canister was transported to NASA Johnson Space Center (JSC) in Houston, Texas where it was opened and samples were processed by the curation team in pristine sample nitrogen gloveboxes. As the sample analysis phase of the OSIRIS-REx mission concludes, the Sample Analysis Team (SAT) has returned the majority of mission samples to NASA JSC curation and will return the remaining samples on a defined timetable. The curation team processed and documented as many of these samples as possible to include in the spring 2026 catalog update and are steadily working to process hundreds of more samples to include in the fall 2026 catalog update.

OSIRIS-REx↗