Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capacity test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Room Temperature Characterization of a Magnetic Bearing for Turbomachinery

Open loop, experimental force and power measurements of a three-axis, radial, heteropolar magnetic bearing at room temperature for rotor speeds up to 20,000 RPM are presented in this paper. The bearing, NASA Glenn Research Center's and Texas A&M's third generation high temperature magnetic bearing, was designed to operate in a 1000 F (540 C) environment and was primarily optimized for maximum load capacity. The experimentally measured force produced by one C-core of this bearing was 630 lb. (2.8 kN) at 16 A, while a load of 650 lbs (2.89 kN) was predicted at 16 A using 1D circuit analysis. The maximum predicted radial load for one of the three axes is 1,440 lbs (6.41 kN) at room temperature. The maximum measured load of an axis was 1050 lbs. (4.73 kN). Results of test under rotating conditions showed that rotor speed has a negligible effect on the bearing's load capacity. A single C-core required approximately 70 W of power to generate 300 lb (1.34 kN) of magnetic force. The room temperature data presented was measured after three thermal cycles up to 1000 F (540 C), totaling six hours at elevated temperatures.

Montague, Gerald↗
DOE OSTI2024

Hard carbon with an opened pore structure for enhanced sodium storage performance

The pore structure of hard carbon has a significant impact on its Na + storage capacity. Herein, a waste wood-derived hard carbon with opened pores (OP-HC) was fabricated with polyvinyl pyrrolidone (PVP) as an additive. Ex situ SAXS and HR-TEM testing results indicate that OP-HC with opened pores and enlarged d 002 interlayer spacing facilitates the reversible (de)sodiation of Na + ions. In situ TEM and XRD testing results demonstrate that OP-HC shows excellent structure stability during the (de)sodiation process. Thus, OP-HC delivers a high reversible charge capacity of 350.7 mA h g −1 at 0.05 C and an ultra-high initial Coulombic efficiency (ICE) of 94.9%. Moreover, OP-HC exhibits excellent cycling stability, and the assembled 18650 full cell with an OP-HC anode can achieve a high capacity retention of 94.5% after 400 cycles at 1.0 A. Furthermore, the excellent electrochemical performance and deep insights into OP-HC with opened pores and increased d 002 interlayer spacing offer a new strategy to design high-performance HC anodes for SIBs.

You, Shunzhang↗
DOE OSTI2024

Ion Exchange Processing of AN-107 Hanford Tank Waste through Crystalline Silicotitanate in a Staged 2- then 3-Column System

The Hanford Site stores an estimated 56 million gallons of mixed radioactive and chemically hazardous waste in large underground tanks. In support of the Direct Feed Low-Activity Waste (DFLAW) Program for expediting Hanford tank waste supernate treatment, laboratory-scale ion exchange processing using prototypic unit operations was conducted on AN-107 tank waste at the Pacific Northwest National Laboratory Radiochemical Processing Laboratory. This report describes the small-scale ion exchange testing with 13.7 L of diluted and filtered supernate from Tank 241-AN-107 (hereafter referred to as AN-107) at 16 °C (62 °F). One of the waste acceptance criteria (WAC) for the Waste Treatment Plant (WTP) Low-Activity Waste Facility is that the waste must contain less than 3.18×10 -5 Ci 137 Cs per mole of Na. For the AN-107 tank waste to meet this criterion, only 0.147% of the influent 137 Cs concentration may be delivered to the WTP; this requires a Cs decontamination factor of 678. Testing with AN-107 matched current Tank Side Cesium Removal (TSCR) facility prototypic operations where a lead-lag configuration was used until the lag column reached the WAC limit, then a polish column was brought online for continued processing in a lead-lag-polish column configuration. Feed was processed at 1.9 bed volumes (BVs) per hour; the flowrate, in terms of contact time with the crystalline silicotitanate (CST) bed, matched the expected flowrate at TSCR. The Cs-decontaminated product was retained for vitrification testing (to be reported separately). The lead column reached 40% Cs breakthrough after processing ~1700 BVs of feed; the 50% Cs breakthrough was extrapolated from the breakthrough data to occur at 1873 BVs. Testing compared to previous AP-101 and AP-107 testing at 16 °C showed ~300 BV increases in volume processed to reach the WAC limit for both lead and lag columns. The increase in capacity was determined to be due to the significantly lower K concentration in the AN-107 compared to the other tank waste matrices. A comparison in breakthrough curves for the three tests indicated slightly slower kinetic behavior in the AN-107, with variations in feed matrices (high organic complexants) likely responsible for the deviation. The Cs effluent from the lag column reached the WAC limit after processing 1097 BVs. Anticipating this breakthrough point, the polish column was preemptively installed around 900 BVs. Cs breakthrough from the lag column began at 500 BVs, reaching 3.06×10 0 µCi/mL, or 2.6 % Cs breakthrough, after processing all 1700 BVs of feed. Table S.1 and Figure S.1 summarize the observed column performance and relevant Cs loading characteristics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Development of a BISON validation case for the TRISO transient irradiations in NSRR using effective heat capacity methods

The current tristructural isotropic (TRISO) fuel assessment and validation database in BISON primarily covers steady- state irradiation and high-temperature furnace testing. Transient assessment cases are potentially needed to support U.S. industry efforts in designing and deploying commercial reactors using TRISO fuels. Historical transient tests in- volving TRISO fuels used highly conservative conditions compared to the typical high-temperature gas-cooled reactor accident scenarios. Despite this, modeling historical transient tests is fundamental for evaluating BISON’s predictive capabilities, adapting material properties for high-temperature and high-particle-power regimes, and developing a sys- tematic validation approach for TRISO transient applications. This work developed a 1D model of transient experiments carried out at the Nuclear Safety Research Reactor using BISON. BISON’s predictions of energy deposition, UO 2 melting onset, and molten volume fractions are compared against experimental measurements. Melting was modeled using an effective specific heat capacity model for UO 2 . We found that BISON’s predictions are in reasonable agreement with experimental data for low-energy-deposition cases, and that BISON overpredicts melting at higher energy depositions. We also discuss the potential causes of discrepancies between the simulated and measured results and propose ways to further develop the model. Although these simulations used conservative conditions compared to those expected for actual TRISO-fueled reactors, they extended the range of conditions reflected in the data in the existing BISON database for TRISO fuels.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2014

Burst Testing of Triaxial Braided Composite Tubes

Applications using triaxial braided composites are limited by the materials transverse strength which is determined by the delamination capacity of unconstrained, free-edge tows. However, structural applications such as cylindrical tubes can be designed to minimize free edge effects and thus the strength with and without edge stresses is relevant to the design process. The transverse strength of triaxial braided composites without edge effects was determined by internally pressurizing tubes. In the absence of edge effects, the axial and transverse strength were comparable. In addition, notched specimens, which minimize the effect of unconstrained tow ends, were tested in a variety of geometries. Although the commonly tested notch geometries exhibited similar axial and transverse net section failure strength, significant dependence on notch configuration was observed. In the absence of unconstrained tows, failure ensues as a result of bias tow rotation, splitting, and fracture at cross-over regions.

Triaxial Braided Composites↗
NASA NTRS2010

Simulation and Optimization of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

Controlling carbon dioxide (CO2) and humidity levels in a spacesuit is critical to ensuring both the safety and comfort of an astronaut during extra-vehicular activity (EVA). Traditionally, this has been accomplished utilizing non-regenerative lithium hydroxide (LiOH) or regenerative metal oxide (MetOx) canisters which pose a significant weight burden. Although such technology enables air revitalization, the volume requirements to store the waste canisters as well as the mass to transport multiple units become prohibitive as mission durations increase. Consequently, motivation exists toward developing a fully regenerative technology for environmental control. The application of solid amine materials with vacuum swing adsorption technology has shown the capacity to control CO2 and concomitantly manage humidity levels through a fully regenerative cycle eliminating mission constraints imposed with non-regenerative technologies. Experimental results for full-size and sub-scale test articles have been collected and are described herein. In order to accelerate the developmental efforts, an axially-dispersed plug ow model with an accompanying energy balance has been established and correlated with the experimental data. The experimental and simulation results display good agreement for a variety of ow rates (110-170 SLM), replicated metabolic challenges (100-590 Watts), and atmosphere pressures under consideration for the spacesuit (248 and 760 mm Hg). The relationship between swing adsorption cycles for an outlet criterion of 6.0 mm Hg of CO2 partial pressure has been established for each metabolic challenge. In addition, variable metabolic profiles were imposed on the test articles in order to assess the ability of the technology to transition to new operational constraints. The advent of the model provides the capacity to apply computer-aided engineering practices to support the ongoing efforts to optimize and mature this technology for future application to space exploration.

Swickrath, Michael J.↗
DOE OSTI2026

A Large-Scale Hardware Experiment Demonstration of Operating High Inverter-Based Resource Power Systems With Grid-Forming Inverters

This paper presents experimental hardware results from a microgrid system as the penetration level of grid-forming (GFM) inverters increases. The experiment aims to showcase the advantages of GFM inverters in enhancing system stability and to investigate the operational challenges in systems relying entirely on inverter-based resources (IBRs). Five test scenarios are devised to progressively increase GFM inverter penetration levels: 0% (S1), 19% (S2), 37% (S3), 68% (S4), and 100% (S5). To ensure consistency, identical loading conditions and dynamic events are applied across all scenarios. The conducted tests include load step changes, output variation of grid-following (GFL) inverters during islanded mode, transition operations (such as synchronization to the grid and islanding), and rateof- change-of-frequency (ROCOF) and voltage jump tests during grid-connected mode. Key findings from the tests are summarized as follows: (1) Scenario S1 proved most challenging for load steps, and GFL variations because of insufficient GFM capacity, leaving the diesel generator unable to handle transient ridethrough; (2) Scenario S5 was the most difficult for transition operations, because the lack of a diesel generator to maintain stiff bus voltage resulted in unexpected reactive power flows during synchronization, causing the point of common coupling (PCC) breaker to trip; (3) Scenarios S4 and S5 were particularly challenging for ROCOF tests because of minimal system inertia, leading to large transients that triggered breaker trips; and (4) Scenario S4 exhibited the strongest voltage recovery capability because of the presence of the diesel generator and a higher number of GFM inverters, both of which possess the highest capacity for reactive power injection.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Cost‐Effective and Scalable Approach for the Separation and Direct Cathode Recovery from End‐of‐Life Li‐Ion Batteries

Li-ion battery recycling presents a promising opportunity to decrease dependence on foreign sources of materials and harvest precious materials within the United States. Herein, a superior complete direct recycling process on individual end-of-life cells is reported where the recovered high-purity cathode active material, as well as electrolyte salt Li hexafluorophosphate (LiPF 6 ) can be reused without significant processing. This new process utilizes a series of mechanical separation steps that enable the separation of the cathode and anode active materials while they are still attached to their current collectors. Using this type of process can significantly reduce metal contamination and enable a clean cathode that can be directly recycled. The process if implemented commercially can greatly reduce the environmental burden of batteries as the greenhouse gas emissions of 8.25 kg CO 2 e kg −1 from the direct recycling process are 64% lower compared to those from virgin production of cathode material. During electrochemical testing of the recovered LiNi 0.6 Mn 0.2 Co 0.2 O 2 a discharge capacity of ≈160 mAh g −1 and good cyclability of over 250 cycles at 0.33C are achieved. This success paves a new pathway to explore and optimize existing Li-ion battery recycling procedures.

electrolyte reuse↗
DOE OSTI2026

Estimating the impact of tariff-driven behind-the-meter storage operation on distribution grid investments

Increasing growth of distributed solar photovoltaics (PV) and electric vehicles (EV) can strain local distribution networks and require costly upgrades. Distributed battery storage, often deployed alongside PV, can be used to mitigate those costs, depending on how batteries are operated. This study evaluates the potential deferral value of distributed battery storage across a range of tariff structures, focusing on the rate structures most commonly available to residential customers today and related variants. Deferrals are evaluated with a least-cost distribution grid expansion optimization model to identify requirements on line reconductoring, transformer upgrades, and voltage regulator installations under each tariff. Results show that TOU rates and net billing tariffs can yield meaningful deferral value, depending on specific tariff structure features. Under the best performing tariff structure tested, storage produced a median annualized deferral value of $7.18 per kW of storage capacity ( kW S ) across all feeders in the sample, though deferral values were considerably larger for feeders with peak loads that coincide with utility system peak, i.e., timing of TOU peak period. In contrast, under an unrestricted TOU design with no restrictions on grid charging or discharging, the median deferral value was $0/ kW S illustrating the critical importance of tariff structure details.

Rodriguez-Garcia, Luis↗
DOE OSTI2022

Ab initio molecular dynamics (AIMD) simulations of NaCl, UCl 3 molten salts

Ab initio molecular dynamics (AIMD) simulations are used to calculate select thermophysical and thermodynamic properties of NaCl, UCl and NaCl-UCl 3 molten salts. Following established approaches, the AIMD simulations include a model for Van der Waals interactions. The Langreth & Lundqvist (vDW-DF2), DFT-D3, and density-dependent energy correction (DFT-dDsC) dispersion models are first tested for molten NaCl in order to assess their accuracy for density and heat capacity predictions across a range of temperatures. Based on the NaCl results, the vdW-DF2 and DFT-dDsC methods are extended to the UCl 3 system and compared to available experimental data. Next, mixtures of NaCl-UCl 3 are investigated and analyzed with respect to the deviation from ideal solution behavior. For the DFT-dDsC simulations, density deviates by up to 2% from an ideal mixture, with the maximum occurring close to the eutectic composition. The mixing energy also deviates from an ideal solution and exhibits a minimum of about -0.074 to eV per formula unit, again close to the eutectic composition. Finally, the compressibility and species diffusivity of the pure and mixed salt systems are calculated. The diffusivities are slightly reduced in the mixed compared to the pure systems and the compressibilities loosely follow a linear correlation as a function of the UCl 3 composition. The trends observed for mixing properties are rationalized by correlating them to the coordination chemistry, which emphasizes the importance of maintaining the extended network formed by U and Cl ions as the NaCl concentration increases. The concentration at which breakdown of the extended network occurs, roughly coincides with the minimum of both the mixing energy and the deviation from ideal solution behavior for density.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Metal–Organic Framework–Polyacrylonitrile Composite Beads for Xenon Capture

Mechanically robust forms of HKUST-1 metal-organic frameworks (MOFs) were fabricated by embedding the MOF in a passive polyacrylonitrile (PAN) matrix at different MOF loadings of 10–90 mass%. Here, the PAN is highly porous and acts as a scaffold that holds the active MOF adsorbent in place for Xe capture. Data presented herein show that the PAN matrix does not notably interfere with the Xe capture process where the Xe capacities scale somewhat linearly with the increase in MOF loading in the composites. Radiation testing of the composites under a gamma flux revealed that they are highly tolerant to these types of radiation fields.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Physiological, genomic, and sulfur isotopic characterization of methanol metabolism by Desulfovibrio carbinolicus

Methanol is often considered as a non-competitive substrate for methanogenic archaea, but an increasing number of sulfate-reducing microorganisms (SRMs) have been reported to be capable of respiring with methanol as an electron donor. A better understanding of the fate of methanol in natural or artificial anaerobic systems thus requires knowledge of the methanol dissimilation by SRMs. In this study, we describe the growth kinetics and sulfur isotope effects of Desulfovibrio carbinolicus, a methanol-oxidizing sulfate-reducing deltaproteobacterium, together with its genome sequence and annotation. D. carbinolicus can grow with a series of alcohols from methanol to butanol. Compared to longer-chain alcohols, however, specific growth and respiration rates decrease by several fold with methanol as an electron donor. Larger sulfur isotope fractionation accompanies slowed growth kinetics, indicating low chemical potential at terminal reductive steps of respiration. In a medium containing both ethanol and methanol, D. carbinolicus does not consume methanol even after the cessation of growth on ethanol. Among the two known methanol dissimilatory systems, the genome of D. carbinolicus contains the genes coding for alcohol dehydrogenase but lacks enzymes analogous to methanol methyltransferase. We analyzed the genomes of 52 additional species of sulfate-reducing bacteria that have been tested for methanol oxidation. There is no apparent relationship between phylogeny and methanol metabolizing capacity, but most gram-negative methanol oxidizers grow poorly, and none carry homologs for methyltransferase (mtaB). Although the amount of available data is limited, it is notable that more than half of the known gram-positive methanol oxidizers have both enzymatic systems, showing enhanced growth relative to the SRMs containing only alcohol dehydrogenase genes. Thus, physiological, genomic, and sulfur isotopic results suggest that D. carbinolicus and close relatives have the ability to metabolize methanol but likely play a limited role in methanol degradation in most natural environments.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Differential Scanning Calorimetry Calibration and Heat Capacity

The Differential Scanning Calorimeter(DSC) is used to find multiple properties ofmaterials such as heat capacity, melting points, crystallization, and more. Fermilabowns the NETZSCH DSC 404 F3 Pegasus to test novel material for a high poweredtargetry components. The DSC heats up to 1500 C, uses a platinum furnace, and Al 2 O 3 crucibles. In order for the DSC to produce consistent and correct data,calibration of the machine was necessary. Testing with the given calibration kit ofknown metals. Once calibrated, testing on novel materials for their specific heatcapacity ensues.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Battery Energy Storage System Evaluation Method

This report describes development of an effort to assess Battery Energy Storage System (BESS) performance that the US DOE Federal Energy Management Program (FEMP) and others can employ to evaluate performance of deployed BESS or solar photovoltaic (PV) +BESS systems. The proposed method is based on actual battery charge and discharge metered data to be collected from BESS systems provided by federal agencies participating in the FEMP's performance assessment initiatives. Long-term (e.g., at least one year) time series (e.g., hourly) charge and discharge data are analyzed to provide approximate estimates of key performance indicators (KPIs).

25 ENERGY STORAGE↗
DOE OSTI2026

EOS at the Fermilab LHC Physics Center(LPC)

The Fermilab CMS LPC center has operated an EOS instance since initial testing began in June 2012, transitioning to production storage in 2013 with an initial capacity of 600\,TB. Today, the system provides approximately 16\,PB of storage to support the 4{,}500-core LPC user analysis cluster, which serves several hundred active CMS users at any given time. In this talk, we will provide an update on our system setup and outline near-term plans for the CMS LPC production EOS system. We will share operational experiences from running our EOS system over the past year. Additionally, we will briefly discuss our recent efforts within the Fermilab Disk Evolution Project to consider the future architecture of HEP data storage at Fermilab for the HL-LHC era.

Wu, Yujun↗
DOE OSTI2026

EOS at the Fermilab LHC Physics Center(LPC)

The Fermilab CMS LPC center has operated an EOS instance since initial testing began in June 2012, transitioning to production storage in 2013 with an initial capacity of 600\,TB. Today, the system provides approximately 16\,PB of storage to support the 4{,}500-core LPC user analysis cluster, which serves several hundred active CMS users at any given time. In this talk, we will provide an update on our system setup and outline near-term plans for the CMS LPC production EOS system. We will share operational experiences from running our EOS system over the past year. Additionally, we will briefly discuss our recent efforts within the Fermilab Disk Evolution Project to consider the future architecture of HEP data storage at Fermilab for the HL-LHC era.

Wu, Yujun↗
NASA NTRS1982

A high-resolution model of the planetary boundary layer - Sensitivity tests and comparisons with SESAME-79 data

A one-dimensional, planetary boundary layer (PBL) model is presented and verified using April 10, 1979 SESAME data. The model contains two modules to account for two different regimes of turbulent mixing. Separate parameterizations are made for stable and unstable conditions, with a predictive slab model for surface temperature. Atmospheric variables in the surface layer are calculated with a prognostic model, with moisture included in the coupled surface/PBL modeling. Sensitivity tests are performed for factors such as moisture availability, albedo, surface roughness, and thermal capacity, and a 24 hr simulation is summarized for day and night conditions. The comparison with the SESAME data comprises three hour intervals, using a time-dependent geostrophic wind. Close correlations were found with daytime conditions, but not in nighttime thermal structure, while the turbulence was faithfully predicted. Both geostrophic flow and surface characteristics were shown to have significant effects on the model predictions

Zhang, D.↗