SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Backscattered UV radiation - Effects of multiple scattering and the lower boundary of the atmosphere

A method is proposed for the calculation of a multiple-scattering correction to the single-scattering calculation of the radiance of the terrestrial atmosphere resulting from backscattered ultraviolet solar radiation in the spectral region used in the ozone profile inversion. This method uses jointly the usual analytical and Monte Carlo methods. Effects of the lower boundary of the atmosphere, cloud tops, and ground surface are investigated both qualitatively and quantitatively. The ratio of multiple to single scattering is determined, and its importance in ozone profile inversion of backscattered UV solar radiation from the terrestrial atmosphere is evaluated. The polarization of the atmospheric radiance is treated briefly.

Aruga, T.↗

NASA NTRS1981

Transonic wing design using potential-flow codes - Successes and failures

The state-of-the-art of transonic wing design by use of computer codes based on the potential flow-theory is presented. The capabilities and limitations of these codes are exemplified by several experiment-theory correlations, including an assessment of pressure distribution from isolated wing and wing-body codes. Computer codes using both conservative and nonconservative differencing schemes were used, and the effects of boundary-layer corrections were considered. Results showed that calculations from a full potential, isolated code correlate well with data from an isolated wing test, but may give poor predictions of the aerodynamic characteristics of some wing-body configurations. Boundary-layer correlations were found to have only moderate effects on experiment-theory correlation. Aeroelastic effects were considered important for high aspect ratio wings of low to moderate thickness, and viscous effects were minimal for typical cruise conditions, even for Reynold's numbers as low as two million. The effect of wind-tunnel walls on experiment-theory correlations remained inconclusive. A wing-body code was used to calculate the flow field about a wing-body configuration with body-mounted engines, typical of the transonic Biz-Jet aircraft.

Hicks, R. M.↗

NASA NTRS1987

Euler and Navier-Stokes solutions for the leeside flow over delta wings at supersonic speeds

Distinctly different types of leeside flowfields over highly swept sharp leading edge delta wings in supersonic flow were numerically simulated using Euler and Navier-Stokes solvers. The Euler code was seen to be adequate only in predicting primary flow structures (leading edge vortex and cross flow shock) whereas the Navier-Stokes code was capable of predicting secondary flow structures (i.e., secondary vortex). A comparison of laminar and turbulent Navier-Stokes solutions indicated that the turbulent boundary layer model is more accurate in predicting the effect of the boundary layer model on the flowfield. Also, the Navier-Stokes code indicated detailed flow structures not observed in the qualitative experimental data available (i.e., vapor screen photographs) indicating a need for quantitative flow field data.

Mcmillin, S. N.↗

DOE OSTI2026

A Multiscale Simulation Study of the Effects of Nantucket Island on Atmospheric Boundary Layer Flow

Multiscale atmospheric simulations were conducted to investigate how Nantucket Island modifies the marine atmospheric boundary layer (ABL) flow, how the mechanisms responsible are represented in mesoscale versus large-eddy simulation (LES) domains, and potential impacts on wind energy production downstream, in moderate and high wind speed cases. Here, to isolate the effects of the island, each case study was simulated (i) with and without island topography included and (ii) with observed versus spatially uniform sea surface temperature (SST) values, the latter removing the influence of spatial variability in SST, while also enabling the examination of how the island effects vary with near-surface thermodynamic stability over the surrounding ocean. Island effects were found to be strongest during daytime heating, which generates convective rolls that redistribute momentum vertically over the island and downstream. Colder SSTs and weaker winds strengthen these rolls and extend their influence. Flow statistics within a representative wind turbine rotor-swept area downstream show that while vertical momentum redistribution enhances near-surface wind speeds, those aloft decrease, resulting in minimal net change to rotor-equivalent wind speed and slightly reduced vertical shear. Comparisons of mesoscale and LES domains reveal that both capture the roughness-driven near-surface slowdown, but mesoscale models underestimate vertical momentum transport compared to LES, which explicitly resolves convective rolls. Increasing LES resolution beyond the grid spacing required to begin capturing the largest convective roll structures ∼ O(100) m yields minimal additional momentum transport but increases resolved turbulence kinetic energy, relevant for stress loading.

Atmosphere-land interaction↗

NASA NTRS1994

Imaging the effect of dipole tilt on magetotail boundaries

Eight years of Interplanetary Monitoring Platform (IMP) 8, four years of International Sun Earth Explorer (ISEE) 2, and one year of IMP 7 magnetometer data have been combined to produce an 'image' of the average magnetic field for a YZ cross section (aberrated GSM) of the magnetotail at a downtail distance of 25 R(sub E). The shape of the neutral sheet and magnetopause boundaries can be observed directly from the images. A fitting function that qualitatively matches the observed boundary shape can then be chosen. This approach improves on previous fits to possible unsuitable functional forms specified independently of the data. In addition, as a refinement of previous studies, we have corrected for varying solar wind dynamic pressure and the effects of tail flaring. We find the magnetopause is displaced above the XY plane with increasing dipole tilt. The neutral sheet is found to curve slightly more than the model of Fairlfield (1980) during times of large dipole tilt and near the flanks appears to differ substantially from the neutral sheet shape given by the analytic model of Voigt (1984), the more recent neutral sheet model of Dandouras (1988) based on the Voigt model, and the semi-empirical model of Tsyganenko (1989).

Hammond, C. Max↗

NASA NTRS2011

Effects of Nose Bluntness on Hypersonic Boundary-Layer Receptivity and Stability Over Cones

The receptivity to freestream acoustic disturbances and the stability properties of hypersonic boundary layers are numerically investigated for boundary-layer flows over a 5 straight cone at a freestream Mach number of 6.0. To compute the shock and the interaction of the shock with the instability waves, the Navier-Stokes equations in axisymmetric coordinates were solved. In the governing equations, inviscid and viscous flux vectors are discretized using a fifth-order accurate weighted-essentially-non-oscillatory scheme. A third-order accurate total-variation-diminishing Runge-Kutta scheme is employed for time integration. After the mean flow field is computed, disturbances are introduced at the upstream end of the computational domain. The appearance of instability waves near the nose region and the receptivity of the boundary layer with respect to slow mode acoustic waves are investigated. Computations confirm the stabilizing effect of nose bluntness and the role of the entropy layer in the delay of boundary-layer transition. The current solutions, compared with experimental observations and other computational results, exhibit good agreement.

Kara, Kursat↗

NASA NTRS1978

Turbulent boundary layers with large streamline curvature effects

It has been shown that turbulent flows are greatly affected by streamline curvature. In spite of this and the fact that curved shear flows are frequently encountered in engineering applications, the predictions of such flows are relatively less developed than the predictions of two-dimensional plane flows. Recently, various attempts were made by different investigators; however, their methods are only successful when the product of the boundary layer thickness to the local surface curvature is approximately 0.05. The present paper investigates the more general case where this product is in the range from 0.1 to 0.5. Results show that the calculated boundary-layer characteristics for arbitrary free stream conditions are in good agreement with measurements.

So, R. M. C.↗

DOE OSTI2020

Axial magnetic flux amplification in Hall-magnetohydrodynamic simulations of externally magnetized z-pinches

It is shown that externally magnetized gas-puff z-pinches under compression can exhibit robust axial flux amplification under suitable axial boundary conditions. This effect relies upon the Hall term in the generalized Ohm's law to generate azimuthal currents in the presence of a driving axial electric field. Under dynamic compression, the total current tends to flow in a mostly force-free boundary layer, separating the predominately azimuthal field outside the layer and the predominately axial field inside the layer. The effect only appears to occur if the axial boundaries allow for outflow or absorption of electromagnetic energy. The effect is mitigated by imposing either periodic or conducting axial boundary conditions. A semi-analytic equilibrium analysis agrees with steady-state solutions of the time-dependent electron-magnetohydrodynamic equations and provides an estimate of the scaling of the boundary layer as well as suggesting a scenario for the formation of the boundary layer. When operative, the effect can significantly impede plasma compression due to the increase in axial flux that diffuses into the pre-compressed plasma or through the presence of conductors that inhibit movement of the generated axial flux. Several facilities have noted unusual implosion behavior in z-pinch experiments with applied axial fields that does not appear to be explainable within the standard magnetohydrodynamic model. In conclusion, it is suggested that these experiments can be explained by the axial flux amplification and concentration effect

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

A study on the creep behavior of alloy 709 using in-situ scanning electron microscopy

In this research, an experimental evaluation of creep properties of Alloy 709 in the temperature range of 750–850 °C was undertaken. Alloy 709 is a novel austenitic stainless steel with 20% Cr and 25% Ni by wt% that was developed for application in structural components of nuclear power plants. Creep rupture tests were conducted in an in-situ heating-loading and Scanning Electron Microscope (SEM) unit equipped with Electron Backscatter Diffraction (EBSD) detector and Energy Dispersive Spectroscopy (EDS). “Real-time” creep damage mechanisms of Alloy 709 at various stresses and temperatures using a flat, un-notched sample with continuously reducing cross-section is studied so that the failure and maximum creep damage occurred at the center of the sample where the in-situ SEM imaging could be focused. Accelerated creep tests at temperatures and stresses above service conditions were performed by employing multiple blocks of constant loads where the loads were increased once the sample attained constant creep rate, indicating a secondary creep regime. This technique ensures multiple data points can be obtained from the same test, saves the time required for an otherwise long-term creep test and usage of SEM. Further, Coincident Site Lattice (CSL) boundary maps were collected as control maps before testing, and the grain boundaries were observed during the creep test to understand the effect of grain boundary character on the creep damage mechanism. Void growth, grain boundary separation, and sliding were found to be the main creep mechanisms whose rate is dependent on stress and temperature. Failure mechanisms studied on the fracture surface using SEM fractography were correlated to the sample surface observations to create complementary information to better understand the underline creep mechanism of Alloy 709.

36 MATERIALS SCIENCE↗

NASA NTRS1975

The effect of grazing flow on the steady state resistance of square-edged orifices

A simple inviscid interaction model has been developed which uses thin airfoil theory to account for pressure forces exerted at the interface between the orifice and grazing flow together with a one-dimensional discharge coefficient concept. The effect of grazing flow boundary layer thickness was also included in the model. Resistance measurements for a wide range of grazing flow speeds and orifice flow rates collapse into a single curve when plotted in terms of effective discharge coefficient versus orifice-to-grazing velocity ratio. The correlation curves for inflow and outflow are different. Data for clustered orifices collapse in the same way as the single orifice. The effect of boundary layer thickness is compared with model predictions. The effect of orifice length-diameter ratio is shown to be significant for inflow but negligible for outflow.

Rogers, T.↗

NASA NTRS1998

Effects of Ice Accretion on Aircraft Aerodynamics

The primary objective of this research was to support the development of a new ice accretion model by improving our physical understanding of the ice accretion process through experimental measurements. The focus was on the effect of the initial ice roughness (smooth/rough boundary) on the accretion process. This includes understanding the boundary-layer development over the roughness and especially its effect on the heat transfer which is fundamental to the ice accretion process. The research focused on acquiring the experimental data needed to formulate a new ice accretion physical model. Research was conducted to analyze boundary-layer data taken on a NACA 0012 airfoil with roughness to simulate the smooth/rough boundary. The effect of isolated roughness on boundary-layer transition was studied experimentally to determine if the classical critical roughness Reynolds number criteria could be applied to transition in the airfoil leading-edge area. The effect of simulated smooth/rough boundary roughness on convective heat transfer was studied to complete the study. During the course of this research the effect of free-stream wind tunnel turbulence on the boundary layer was measured. Since this quantity was not well known, research to accurately measure the wind tunnel turbulence in an icing cloud was undertaken. Preliminary results were attained and the final data were acquired, reduced and presented under a subsequent grant.

Bragg, Michael B.↗

NASA NTRS1947

Effect of Various Methods of Boundary-Layer Control on Performance of V-1710-93 Engine-Stage Supercharger

Four methods of boundary-layer control were tried during an investigation to improve the flow in the impeller passages of a V-1710-93 engine-stage supercharger. The boundary layer along the impeller front shroud was removed by suction. In one method the removal was accomplished by recirculation of the air to the impeller inlet; in another method, by external removal. In the other methods, slots were cut through the impeller-blade faces first at 30 percent and then at 30 and 70 percent of the mean-flow-path length measured from leading edges of the rotating inlet guide vanes to introduce air from the high-pressure side of the blades into the region where stagnation and separation were suspected. A slight improvement in performance was obtained when the boundary layer was removed through the impeller front shroud. In general, this improvement become more pronounced as the amount of air removed was increased even though the excessive impeller frontal clearance maintained for these tests, together with an exaggerated negative pressure gradient, apparently induced flow separation on the diffuser front and rear walls as well as on the impeller front shroud. The use of slots in the impellers at the locations selected had a detrimental effect on the supercharger performance characteristics.

Kohl, Robert C.↗

NASA NTRS1980

Electric field effects on galactic cosmic rays at the heliosphere boundary

The boundary condition for galactic cosmic rays at the outer edge of the modulation region was examined. With few exceptions authors have in the past uncritically used a time-independent, spherically-symmetric condition. It was found that, depending on the mechanism by which the heliospheric magnetic field connects to the general galactic magnetic field, the induced electric field may have important effects on the boundary condition. Sample calculations are presented which illustrate the potentially large, nonspherically-symmetric effects which may be expected.

Jokipii, J. R.↗

NASA NTRS1991

Gyro-phase effects near the storm-time boundary of energetic plasma

The nonadiabatic acceleration of plasma sheet ions during the expansion phase of substorms is examined by means of single-particle codes. It is shown that, in the near-earth plasma sheet, the gyration phase at substorm onset controls the net ion energization, as the gyro-period is locally comparable to the field variation time scale. This can yield a particularly significant decrease of the particle magnetic moment. It is accordingly argued that, via adiabatic invariant violation, the dipolarization of magnetospheric field lines can induce a 'de-trapping' of inner plasma sheet populations and, hence, give rise to short-lived precipitation enhancements over the auroral zone. As this effect depends upon cyclotron frequency, it is expected to occur at distinct latitudes for different ion species. This contrasts with nonadiabatic ion behavior further out into the geotail, which is characterized by intense perpendicular heating and a likely collective trapping.

Delcourt, D. C.↗

DOE OSTI2021

Void growth via dislocation pileup impingement on grain boundary

In this work, the effect of edge dislocations, impinging on grain boundary in fcc Fe near a preexisting void on the volume of this void, was studied using MD simulation. It was found that virtually unlimited growth of the void via this mechanism is possible under certain conditions. To the best of our knowledge this is the first atomistic simulation study, demonstrating feasibility of this void growth mechanism.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Solute clustering in polycrystals: Unveiling the interplay of grain boundary junction and long-range solute attraction effects

Spectral analysis of local atomic environments has become a powerful tool for studying solute atom segregation and interactions at grain boundaries in nanocrystalline alloys. When applied to individual grain boundaries, the spectral analysis has shown that solute-solute interaction can be either attractive or repulsive, with long-range relative attraction enhancing the likelihood for solute atoms to begin clustering. In this article, we combine this analysis with a new grain-boundary structure descriptor based on grain-boundary atom coordination, to investigate the impact of grain-boundary junctions on solute atom segregation in polycrystals. Specifically, we systematically characterize the tendency of solute clusters to begin forming at various types of ordinary grain boundaries, triple junctions, and high-order junctions in Ag polycrystals containing either Ni or Cu solute atoms. Our findings demonstrate that the formation of solute clusters at grain boundaries is primarily driven by long-range relative solute attraction, rather than short-range solute-solute interactions. Furthermore, this effect is most pronounced near grain-boundary junctions. Our study highlights the multiscale nature of solute segregation at crystalline interfaces and provides new insights into the complex phenomena governing heterogeneous solute segregation in grain-boundary networks.

Grain-boundary junction↗

DOE OSTI2024

Transducer Resolution Effect on Pressure Fluctuations Beneath Hypersonic Turbulent Boundary Layers

The size of a pressure transducer is known to affect the accuracy of measurements of wall-pressure fluctuations beneath a turbulent boundary layer because of spatial averaging over the sensing area of the transducer. In this paper, the effect of finite transducer size is investigated by applying spatial averaging or wavenumber filters to a database of hypersonic wall pressure generated from a direct numerical simulation (DNS) that simulates the turbulent portion of the boundary layer over a sharp 7° half-angle cone at nominally Mach 8. Here, a good comparison between the DNS and the experiment in the Sandia Hypersonic Wind Tunnel at Mach 8 is achieved after spatial averaging is applied to the DNS data over an area similar to the sensing area of the transducer. The study shows that a finite sensor size similar to that of the PCB132 transducer can cause significant attenuation in the root-mean-square and power spectral density (PSD) of wall-pressure fluctuations, and the attenuation effect is identical between cone and flat plate configurations at the same friction Reynolds number. The Corcos theory is found to successfully compensate for the attenuated high-frequency components of the wall-pressure PSD.

42 ENGINEERING↗

NASA NTRS2012

CFD Simulations for the Effect of Unsteady Wakes on the Boundary Layer of a Highly Loaded Low-Pressure Turbine Airfoil (L1A)

This report is the third part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part was published as NASA/CR-2012-217415. The second part was published as NASA/CR-2012-217416. The study of the very high lift low-pressure turbine airfoil L1A in the presence of unsteady wakes was performed computationally and compared against experimental results. The experiments were conducted in a low speed wind tunnel under high (4.9%) and then low (0.6%) freestream turbulence intensity for Reynolds number equal to 25,000 and 50,000. The experimental and computational data have shown that in cases without wakes, the boundary layer separated without reattachment. The CFD was done with LES and URANS utilizing the finite-volume code ANSYS Fluent (ANSYS, Inc.) under the same freestream turbulence and Reynolds number conditions as the experiment but only at a rod to blade spacing of 1. With wakes, separation was largely suppressed, particularly if the wake passing frequency was sufficiently high. This was validated in the 3D CFD efforts by comparing the experimental results for the pressure coefficients and velocity profiles, which were reasonable for all cases examined. The 2D CFD efforts failed to capture the three dimensionality effects of the wake and thus were less consistent with the experimental data. The effect of the freestream turbulence intensity levels also showed a little more consistency with the experimental data at higher intensities when compared with the low intensity cases. Additional cases with higher wake passing frequencies which were not run experimentally were simulated. The results showed that an initial 25% increase from the experimental wake passing greatly reduced the size of the separation bubble, nearly completely suppressing it.

Vinci, Samuel, J.↗