Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Comparison of analytical and experimental subsonic steady and unsteady pressure distributions for a high-aspect-ratio-supercritical wing model with oscillating control surfaces

The results of a comparative study using the unsteady aerodynamic lifting surface theory, known as the Doublet Lattice method, and experimental subsonic steady- and unsteady-pressure measurements, are presented for a high-aspect-ratio supercritical wing model. Comparisons of pressure distributions due to wing angle of attack and control-surface deflections were made. In general, good correlation existed between experimental and theoretical data over most of the wing planform. The more significant deviations found between experimental and theoretical data were in the vicinity of control surfaces for both static and oscillatory control-surface deflections.

Mccain, W. E.↗
NASA NTRS1982

Adaptive-wall wind-tunnel research at Ames Research Center

Adaptive-wall wind-tunnel research is summarized. This research includes small-scale two- and three-dimensional wind-tunnel experiments and numerical experiments with a three-dimensional adaptive-wall simulator. Airflow through the test-section walls is controlled by adjusting the pressures in segmented plenums. Interference free conditions are successfully attained in subsonic and transonic flows. An adaptive wall test section is constructed for the transonic wind tunnel. Wall interference was reduced in the three dimensional experiment at several angles of attack at Mach 0.60. A wing on wall configuration was modeled in the numerical experiments. These flow simulations showed that free air conditions can be approximated by adjusting boundary conditions at only the floor and ceiling of the test section. No sidewall control was necessary.

Schairer, E. T.↗
NASA NTRS1983

Thrust-induced effects on subsonic longitudinal aerodynamic characteristics of a vectored-engine-over-wing configuration

An investigation was conducted in the Langley 4 by 7 Meter Tunnel of the thrust induced effects on the longitudinal aerodynamic characteristics of a vectored-engine-over-wing fighter aircraft. The investigation was conducted at Mach numbers from 0.14 to 0.17 over an angle-of-attack range from -2 deg to 26 deg. The major model variables were the spanwise blowing nozzle sweep angle and main nozzle vector angle along with trailing edge, flap deflections. The overall thrust coefficient (main and spanwise nozzles) was varied from 0 (jet off) to 2.0. The results indicate that the thrust-induced effects from the main nozzle alone were small and mainly due to boundary-layer control affecting a small area behind the nozzle. When the spanwise blowing nozzles were included, the induced effects were larger than the main nozzle alone and were due to both boundary layer control and induced circulation lift. No leading edge vortex effects were evident.

Quinto, P. F.↗
NASA NTRS1984

Estimated low-speed aerodynamic parameters of an advanced fighter from flight and wind tunnel data

A procedure for determination of aerodynamic model structure and estimation of aerodynamic parameters is applied to data from a modern fighter operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, postulated models for airplane aerodynamic coefficients and flight data analysis. The results presented contain only a small number of selected longitudinal and lateral parameters. These parameters were obtained from various maneuvers and subsets of joined data from several flights. The estimated parameters are in good agreement with the wind tunnel measurements. The resulting aerodynamic model equations seem to be satisfactory for the prediction of airplane motion.

Klein, V.↗
NASA NTRS1987

Force and moment tests to determine the interaction effects of the reaction control system jet plumes on the space shuttle Orbiter aerodynamics at Mach Number 6 (Test OA352)

The purpose of this test was to expand the existing Space Shuttle aerodynamics and Reaction Control System (RCS) data base to support the Glide Return to Launch Site (GRTLS) abort trajectory and the new Digital Autopilot. An existing model of the orbiter was used to investigate the aerodynamic effects of several combinations of RCS thrusters and thruster momentum ratios at Mach number 6. Two separate model installations were used to achieve an angle-of-attack range of -11 to 46 deg. The test was conducted at a unit Reynolds number of 0.8 x 10 to the 6th per foot.

Cayse, Robert W.↗
NASA NTRS1987

Experimental investigation of the aerodynamic characteristics for a winged-cone concept

Experimental longitudinal and lateral-directional aerodynamics were obtained for a generic aerodynamics were obtaiend for a generic winged-cone configuration having possible application as a transatmospheric vehicle concept. Data were obtained at Mach numbers from 0.6 to 20.0; Reynolds numbers, based on model length, between 2.5 and 5.3 million; and angles of attack from -4 to 20 deg. Results indicate a longitudinal center-of-pressure travel of about 23 percent of the fuselage length for the test Mach number range, with longitudinal instabilities noted at high-supersonic to hypersonic Mach numbers. These instabilities are coupled with directional instability at similar Mach numbers. Predictions with analytic codes, namely, the USAF DATCOM and the tangent-cone option of the Hypersonic Arbitrary Body Program, provided fair agreement with the experimental aerodynamic characteristics at low angles-of-attack.

Phillips, W. Pelham↗
NASA NTRS1988

Navier-Stokes calculations of hovering rotor flowfields

Unsteady, thin-layer Navier-Stokes equations written in rotor coordinates are solved using a partially flux-split, implicit numerical algorithm to calculate the flowfields of a hovering rotor blade at subsonic and transonic conditions. Numerical results are in good agreement with experimental data for both nonlifting and lifting rectangular blades. For the lifting case, the rotor wake effects are modeled by applying a correction to the geometric angle of attack of the blades. Alternate methods of calculating the hovering rotor flowfields in blade-fixed mode that have the same circulation distribution as a hovering blade are explored. All of the results presented in this paper were computed on a Cray-2 supercomputer.

Srinivasan, G. R.↗
NASA NTRS1992

Vortical flow control on a wing-body combination using tangential blowing

The objective of the experimental program reported here was to evaluate the possibility of using tangential blowing to create roll and yaw control on a delta wing-forebody combination at high angles of attack. It is found that the vortical flow over the model can be manipulated more efficiently by blowing on the nose section rather than fuselage. Large rolling moments and side forces are generated by blowing from forebody compared to wing blowing. For a wing-body combination, a model with a blunt nose is found to be less sensitive to flow asymmetry than a sharp-nosed configuration. Rolling moment changes sign from prestall to stall for all the configurations tested.

Celik, Zeki Z.↗
NASA NTRS1993

Robust control of hypersonic vehicles considering propulsive and aeroelastic effects

The influence of propulsion system variations and elastic fuselage behavior on the flight control system of an airbreathing hypersonic vehicle is investigated. Thrust vector magnitude and direction changes due to angle of attack variations affect the pitching moment. Low structural vibration frequencies may occur close to the rigid body modes influencing the angle of attack and lead to possible cross coupling. These effects are modeled as uncertainties in the context of a robust control study of a hypersonic vehicle model accelerating through Mach 8 using H-infinity and mu synthesis techniques. Various levels of uncertainty are introduced into the system. Both individual and simultaneous appearance of uncertainty are considered. The results indicate that the chosen design technique is suitable for this kind of problem provided that a fairly good knowledge of the effects mentioned above is available. The order of the designed controller is reduced but robust performance is lost which shows the need for fixed order design techniques.

Buschek, Harald↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1937

Calculated and Measured Pressure Distributions over the Midspan Section of the NACA 4412 Airfoil

Pressures were simultaneously measured in the variable-density tunnel at 54 orifices distributed over the midspan section of 5 by 30 inch rectangular model of the NACA 4412 airfoil at 17 angles of attack ranging from -20 degrees to 30 degrees at a Reynolds number of approximately 3,000,000. Accurate data were thus obtained for studying the deviations of the results of potential-flow theory from measured results. The results of the analysis and a discussion of the experimental technique are presented.

Pinkerton, Robert M↗
NASA NTRS1994

Feedback control laws for highly maneuverable aircraft

During the first half of the year, the investigators concentrated their efforts on completing the design of control laws for the longitudinal axis of the HARV. During the second half of the year they concentrated on the synthesis of control laws for the lateral-directional axes. The longitudinal control law design efforts can be briefly summarized as follows. Longitudinal control laws were developed for the HARV using mu synthesis design techniques coupled with dynamic inversion. An inner loop dynamic inversion controller was used to simplify the system dynamics by eliminating the aerodynamic nonlinearities and inertial cross coupling. Models of the errors resulting from uncertainties in the principal longitudinal aerodynamic terms were developed and included in the model of the HARV with the inner loop dynamic inversion controller. This resulted in an inner loop transfer function model which was an integrator with the modeling errors characterized as uncertainties in gain and phase. Outer loop controllers were then designed using mu synthesis to provide robustness to these modeling errors and give desired response to pilot inputs. Both pitch rate and angle of attack command following systems were designed. The following tasks have been accomplished for the lateral-directional controllers: inner and outer loop dynamic inversion controllers have been designed; an error model based on a linearized perturbation model of the inner loop system was derived; controllers for the inner loop system have been designed, using classical techniques, that control roll rate and Dutch roll response; the inner loop dynamic inversion and classical controllers have been implemented on the six degree of freedom simulation; and lateral-directional control allocation scheme has been developed based on minimizing required control effort.

Garrard, William L.↗
NASA NTRS1959

Flight Tests of A 1/8-Scale Model of the Bell D-188A Jet VTOL Airplane

The Bell D-188A VTOL airplane is a horizontal-attitude VTOL fighter with tilting engine nacelles at the tips of a low-aspect-ratio unswept wing and additional engines in the fuselage. The model could be flown smoothly in hovering and transition flight. In forward flight the model could be flown smoothly at the lower angles of attack but experienced an uncontrollable directional divergence at angles of attack above about 16 deg.

Smith, Charles C., Jr.↗
NASA NTRS1961

Static Longitudinal and Lateral Stability Characteristics of a Right Triangular Pyramidal Lifting Reentry Configuration at Transonic Speeds

The static longitudinal and lateral stability characteristics of a right triangular pyramidal lifting reentry configuration have been investigated at Mach numbers from 0.60 to 1.19 for angles of attack up to 27.3 deg. The lower surfaces of the model had a dihedral angle of 45 deg, and the upper surface was flat. The leading-edge sweep of the model was 79.5 deg.

Olstad, Walter B.↗
NASA NTRS1950

Transonic Stability and Control Investigation of a 1/80-Scale Model of the Consolidated Vultee Skate 9 Seaplane, TED No. NACA DE 345: Transonic-Bump Method

An investigation of the longitudinal stability and of the all-movable horizontal tail and aileron control of a 1/80-scale reflection-plane model of the Consolidated Vultee Skate 9 seaplane has been made through a Mach number range of 0.6 to 1.16 on the transonic bump of the Langley high-speed 7- by 10-foot tunnel. At moderate lift coefficients (0.4 to 0.8) and below a Mach number of 1.0 the model was statically unstable longitudinally. The static longitudinal stability of the model at low lift coefficients increased with Mach number corresponding to a shift in aerodynamic center from 37 percent mean aerodynamic chord at a Mach number of 0.60 to 64 percent at a Mach number of 1.10. Estimates indicate that the tail deflection angle required for steady flight and for accelerated maneuvers of the Skate 9 airplane would probably not vary greatly with Mach number at sea level, but for accelerated maneuvers at altitude the tail deflection angle would probably vary erratically with Mach number. The variation of rolling-moment coefficient with aileron deflection angle was approximately linear, agreed well with theory, and held for the range of aileron deflections tested (-17.1 deg to 16.6 deg). At low lift coefficients the drag rise occurred at Mach numbers of 0.95 and 0.90 for the wing alone and the complete model, respectively. The effects of the canopy on the model were small. For the ranges investigated, angle-of-attack and Mach number changes caused no large pressure drops in the jet-engine duct.

Riebe, John M.↗
NASA NTRS1949

Wind-Tunnel Investigation of the Low-Speed Static Stability and Control Characteristics of a Model of Bell MX-776

An investigation has been made in the Langley stability tunnel to determine the low-speed static stability and control characteristics of a model of the Bell MX-776. The results of the investigation indicated that the basic model configuration was longitudinally stable in the angle-of-attack range from about -16 deg. to 16 deg. but that the stability was a minimum near O deg angle of attack. The data indicated an aerodynamic-center position about 0.64 body diameters behind the center of gravity at low angles of attack. Reduction in the size of the front horizontal fins increased the longitudinal stability. With 20 percent of the span of the normal front horizontal fins cut off the aerodynamic center was about 1.04 body diameters behind the center of gravity, and with front horizontal fins having the same area as the front vertical fins, the aerodynamic center was 2.26 body diameters behind the center of gravity (at low angles of attack).

Queijo, M. J.↗
NASA NTRS2016

Ice Accretions and Full-Scale Iced Aerodynamic Performance Data for a Two-Dimensional NACA 23012 Airfoil

This report documents the data collected during the large wind tunnel campaigns conducted as part of the SUNSET project (StUdies oN Scaling EffecTs due to ice) also known as the Ice-Accretion Aerodynamics Simulation study: a joint effort by NASA, the Office National d'Etudes et Recherches Aérospatiales (ONERA), and the University of Illinois. These data form a benchmark database of full-scale ice accretions and corresponding ice-contaminated aerodynamic performance data for a two-dimensional (2D) NACA 23012 airfoil. The wider research effort also included an analysis of ice-contaminated aerodynamics that categorized ice accretions by aerodynamic effects and an investigation of subscale, low- Reynolds-number ice-contaminated aerodynamics for the NACA 23012 airfoil. The low-Reynolds-number investigation included an analysis of the geometric fidelity needed to reliably assess aerodynamic effects of airfoil icing using artificial ice shapes. Included herein are records of the ice accreted during campaigns in NASA Glenn Research Center's Icing Research Tunnel (IRT). Two different 2D NACA 23012 airfoil models were used during these campaigns; an 18-in. (45.7-cm) chord (subscale) model and a 72-in. (182.9-cm) chord (full-scale) model. The aircraft icing conditions used during these campaigns were selected from the Federal Aviation Administration's (FAA's) Code of Federal Regulations (CFR) Part 25 Appendix C icing envelopes. The records include the test conditions, photographs of the ice accreted, tracings of the ice, and ice depth measurements. Model coordinates and pressure tap locations are also presented. Also included herein are the data recorded during a wind tunnel campaign conducted in the F1 Subsonic Pressurized Wind Tunnel of ONERA. The F1 tunnel is a pressured, high- Reynolds-number facility that could accommodate the full-scale (72-in. (182.9-cm) chord) 2D NACA 23012 model. Molds were made of the ice accreted during selected test runs of the full-scale model in the IRT. From these molds, castings were made that closely replicated the features of the accreted ice. The castings were then mounted on the full-scale model in the F1 tunnel, and aerodynamic performance measurements were made using model surface pressure taps, the facility force balance system, and a large wake rake designed specifically for these tests. Tests were run over a range of Reynolds and Mach numbers. For each run, the model was rotated over a range of angles-of-attack that included airfoil stall. The benchmark data collected during these campaigns were, and continue to be, used for various purposes. The full-scale data form a unique, ice-accretion and associated aerodynamic performance dataset that can be used as a reference when addressing concerns regarding the use of subscale ice-accretion data to assess full-scale icing effects. Further, the data may be used in the development or enhancement of both ice-accretion prediction codes and computational fluid dynamic codes when applied to study the effects of icing. Finally, as was done in the wider study, the data may be used to help determine the level of geometric fidelity needed for artificial ice used to assess aerodynamic degradation due to aircraft icing. The structured, multifaceted approach used in this research effort provides a unique perspective on the aerodynamic effects of aircraft icing. The data presented in this report are available in electronic form upon formal approval by proper NASA and ONERA authorities.

Addy, Harold E., Jr.↗