Results for “alloy development” — Page 48

NASA NTRS2006

Cyclic Oxidation Behavior of Cold Sprayed CuCrAl-Coated and Uncoated GRCop-84 Substrates for Space Launch Vehicles

A newly developed Cu-23 (wt %) Cr-5%Al (CuCrAl) alloy shown to resist hydridation and oxidation in an as-cast form is currently being considered as a protective coating for GRCop-84, which is an advanced copper alloy containing 8 (at.%) Cr and 4 (at.%) Nb. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique. Cyclic oxidation tests conducted in air on both coated and uncoated substrates between 773 and 1073 K revealed that the coating remained intact and protected the substrate up to 1073 K. No significant weight loss of the coated specimens were observed at 773 and 873 K even after a cumulative cyclic time of 500 h. About a 10 percent weight loss observed at 973 and 1073 K was attributed to the excessive oxidation of the uncoated sides. In contrast, the uncoated substrate lost as much as 80 percent of its original weight under similar test conditions. It is concluded that the cold sprayed CuCrAl coating is suitable for protecting GRCop-84 substrates.

Raj, S. V.↗

NASA NTRS2007

Characterization of Cold Sprayed CuCrAl-Coated and Uncoated GRCop-84 Substrates for Space Launch Vehicles

A newly developed Cu-23(wt.%)Cr-5%Al (CuCrAl) alloy is currently being considered as a protective coating for GRCop-84 (Cu-8(at.%)Cr-4%Nb). The coating was deposited on GRCop-84 substrates by the cold spray deposition technique. Cyclic oxidation tests conducted in air on both coated and uncoated substrates between 773 and 1073 K revealed that the coating remained intact and protected the substrate up to 1073 K. No significant weight loss of the coated specimens were observed at 773 and 873 K even after a cumulative cyclic time of 500 h. In contrast, the uncoated substrate lost as much as 80% of its original weight under similar test conditions. Low cycle fatigue tests revealed that the fatigue lives of thinly coated GRCop-84 specimens were similar to the uncoated specimens within the limits of experimental scatter. It is concluded that the cold sprayed CuCrAl coating is suitable for protecting GRCop-84 substrates.

Raj, S. V.↗

NASA NTRS2007

Development of Multifunctional Radiation Shielding Materials for Long Duration Human Exploration Beyond the Low Earth Orbit

One of the major challenges for long duration human exploration beyond the low Earth orbit and sustained human presence on planetary surfaces would be development of materials that would help minimize the radiation exposure to crew and equipment from the interplanetary radiation environment, This radiation environment consists primarily of a continuous flux of galactic cosmic rays (GCR) and transient but intense fluxes of solar energetic particles (SEP). The potential for biological damage by the relatively low percentage of high-energy heavy-ions in the GCR spectrum far outweigh that due to lighter particles because of their ionizing-power and the quality of the resulting biological damage. Although the SEP spectrum does not contain heavy ions and their energy range is much lower than that for GCRs, they however pose serious risks to astronaut health particularly in the event of a bad solar storm The primary purpose of this paper is to discuss our recent efforts in development and evaluation of materials for minimizing the hazards from the interplanetary radiation environment. Traditionally, addition of shielding materials to spacecrafts has invariably resulted in paying a penalty in terms of additional weight. It would therefore be of great benefit if materials could be developed not only with superior shielding effectiveness but also sufficient structural integrity. Such a multifunctional material could then be considered as an integral part of spacecraft structures. Any proposed radiation shielding material for use in outer space should be composed of nuclei that maximize the likelihood of projectile fragmentation while producing the minimum number of target fragments. A modeling based approach will be presented to show that composite materials using hydrogen-rich epoxy matrices reinforced with polyethylene fibers and/or fabrics could effectively meet this requirement. This paper will discuss the fabrication of such a material for a crewed vehicle. Ln addition, the capability of synthesizing radiation shielding materials for habitat structures primarily from Lunar or Martian in-situ resources will also be presented. Such an approach would significantly _reduce the cost associated with transportation of such materials and structures from earth. Results from radiation exposure measurements will be presented demonstrating the shielding effectiveness of the developed materials. Mechanical testing data will be discussed to illustrate that the specific mechanical properties of the developed composites are comparable to structural aluminum based alloys currently used for the space shuttle and space station.

Sen, S.↗

NASA NTRS2017

Shape Morphing Adaptive Radiator Technology (SMART) Updates to Techport Entry

The Shape-Morphing Adaptive Radiator Technology (SMART) project builds off the FY16 research effort that developed a flexible composite radiator panel and demonstrated its ability to actuate from SMA's attached to it. The proposed FY17 Shape-Morphing Adaptive Radiator Technology (SMART) project's goal is to 1) develop a practical radiator design with shape memory alloys (SMAs) bonded to the radiator's panel, and 2) build a multi-panel radiator prototype for subsequent system level thermal vacuum tests. The morphing radiator employs SMA materials to passively change its shape to adapt its rate of heat rejection to vehicle requirements. Conceptually, the radiator panel has a naturally closed position (like a cylinder) in a cold environment. Whenever the radiator's temperature gradually rises, SMA's affixed to the face sheet will pull the face sheet open a commensurate amount - increasing the radiators view to space and causing it to reject more heat. In a vehicle, the radiator's variable heat rejection capabilities would reduce the number of additional heat rejection devices in a vehicle's thermal control system. This technology aims to help achieve the required maximum to minimum heat rejection ratio required for manned space vehicles to adopt a lighter, simpler, single loop thermal control architecture (ATCS). Single loop architectures are viewed as an attractive means to reduce mass and complexity over traditional dual-loop solutions. However, fluids generally considered safe enough to flow within crewed cabins (e.g. propylene glycol-water mixtures) have much higher freezing points and viscosities than those used in the external sides of dual loop ATCSs (e.g. Ammonia and HFE7000).

Erickson, Lisa↗

NASA NTRS2019

Mitigation of Silver Ion Loss from Solution by Polymer Coating of Metal Surfaces

Spacecraft potable water systems require a biocidal agent that effectively provides both immediate and residual disinfection over long periods of time. Ionic silver (Ag+) is a leading candidate for this application, but suffers from rapid concentration loss due interactions with the metal storage containers and tubing. In order to maintain biocidal efficacy in systems with long periods of dormancy and to reduce the required rate of Ag+ injection, it is necessary to develop alternative materials and coatings for certified metal alloys that significantly reduce the Ag+ loss. In this work, we investigate the performance of two unusual polymers, Teflon AF 2400 and parylene-AF4, as barrier coatings under immersion in 400 ppb Ag+. We show that 25 m-thick parylene-AF4 is a promising coating with Ag+ losses similar to PTFE. Key challenges with this material include maintenance of adhesion under long-term immersion and control of deposition during the internal coating of high-aspect ratio tubing. Solutions to these problems may including surface structuring of substrates for mechanical anchoring or an alternative parylene-C chemistry (with more stable adhesion), and dynamic spatio-temporal control of substrate temperature, respectively.

water↗

NASA NTRS2020

Mitigation of Silver Ion Loss from Solution by Polymer Coating of Metal Surfaces, Part II

“Spacecraft potable water systems require a biocidal agent that effectively provides both immediate and residual disinfection over long periods of time. Ionic silver (Ag+) is a leading candidate for this application, but suffers from rapid concentration loss due to interactions with the metal storage containers and tubing. In order to maintain biocidal efficacy in systems with long periods of dormancy and to reduce the required rate of Ag+ injection, it is necessary to develop alternative materials and coatings for certified metal alloys that significantly reduce the Ag+loss.”1In this work, we continue our investigation of vapor-deposited parylene (AF4, and now C) polymers as conformal barrier coatings under long-term (ca. 1-year) immersion in ca. 400 ppb Ag+. The performanceof internal coatings in tubing/two-ferrule fitting systems is characterized. We report successful “aging” and high concentration Ag+pretreatment of parylene coatings for quantitative reduction of Ag+loss rates. In addition, we observe long-term blister-free adhesion of mechanically anchored parylene-AF4 on nano-structured Ti-6Al-4V alloy and chemically bonded parylene-C on 316L stainless steel. Finally, we report preliminary experiments with mechanical and chemical anchoring of laboratory-deposited parylene-C on 316L.

Silver↗

NASA NTRSDate not supplied

Mitigation of Silver Ion Loss from Solution by Polymer Coating of Metal Surfaces, Part IV

“Spacecraft potable water systems require a biocidal agent that effectively provides both immediate and residual disinfection over long periods of time. Ionic silver (Ag+) is a leading candidate for this application, but suffers from rapid concentration loss due to interactions with the metallic storage containers and tubing. In order to maintain biocidal efficacy in systems with long periods of dormancy and to reduce the required rate of Ag+ injection, it is necessary to develop alternative materials and coatings for certified metal alloys that significantly reduce the Ag+ loss.” In previous reports, we have described our investigations addressing Ag+ loss mitigation and adhesion performance of parylene barrier coatings on coupons of several metal alloys and 316L tubing under static immersion. In such conditions, parylene-C and AF4 coatings have shown excellent Ag+ loss mitigation performance, and mixed long-term adhesion performance, depending on parylene species and substrate surface chemistry/structure. In Part IV of this series, we begin to address the performance of parylene-C barrier coatings under more challenging and realistic conditions, in order to evaluate potential suitability in flight systems. Using two testbeds, we characterized coating performance under dynamic mechanical operation. In the Flow/Pressure Testbed System, Ag+ solution is pumped through internally coated 316L tubing, with optional pressure cycling. In the Bellows Tank Testbed System, an internally coated edge-welded 316L bellows containing Ag+ solution is cyclically extended and compressed, analogous to the operation of bellows tanks used for potable water storage and delivery on the International Space Station. Periodic determinations of Ag+ loss with testbed cycling/time and visual observation of the parylene-C coatings were conducted. In addition, we characterized parylene-C coating resilience and Ag+ loss with 316L tubing and multiple fitting types under long-term immersion and repeated fitting dis/reassembly.

Lance Dean Delzeit↗

NASA NTRS2002

Effect of Crystal Orientation on Fatigue Failure of Single Crystal Nickel Base Turbine Blade Superalloys

High cycle fatigue (HCF) induced failures in aircraft gas turbine and rocket engine turbopump blades is a pervasive problem. Single crystal nickel turbine blades are being utilized in rocket engine turbopumps and jet engines throughout industry because of their superior creep, stress rupture, melt resistance, and thermomechanical fatigue capabilities over polycrystalline alloys. Currently the most widely used single crystal turbine blade superalloys are PWA 1480/1493, PWA 1484, RENE' N-5 and CMSX-4. These alloys play an important role in commercial, military and space propulsion systems. Single crystal materials have highly orthotropic properties making the position of the crystal lattice relative to the part geometry a significant factor in the overall analysis. The failure modes of single crystal turbine blades are complicated to predict due to the material orthotropy and variations in crystal orientations. Fatigue life estimation of single crystal turbine blades represents an important aspect of durability assessment. It is therefore of practical interest to develop effective fatigue failure criteria for single crystal nickel alloys and to investigate the effects of variation of primary and secondary crystal orientation on fatigue life. A fatigue failure criterion based on the maximum shear stress amplitude /Delta(sub tau)(sub max))] on the 24 octahedral and 6 cube slip systems, is presented for single crystal nickel superalloys (FCC crystal). This criterion reduces the scatter in uniaxial LCF test data considerably for PWA 1493 at 1200 F in air. Additionally, single crystal turbine blades used in the alternate advanced high-pressure fuel turbopump (AHPFTP/AT) are modeled using a large-scale three-dimensional finite element model. This finite element model is capable of accounting for material orthotrophy and variation in primary and secondary crystal orientation. Effects of variation in crystal orientation on blade stress response are studied based on 297 finite element model runs. Fatigue lives at critical points in the blade are computed using finite element stress results and the failure criterion developed. Stress analysis results in the blade attachment region are also presented. Results presented demonstrates that control of secondary and primary crystallographic orientation has the potential to significantly increase a component S resistance to fatigue crack growth with- out adding additional weight or cost. [DOI: 10.1115/1.1413767]

Arakere, N. K.↗

NASA NTRS2000

Micromechanical Characterization and Texture Analysis of Direct Cast Titanium Alloys Strips

This research was conducted to determine a post-processing technique to optimize mechanical and material properties of a number of Titanium based alloys and aluminides processed via Melt Overflow Solidification Technique (MORST). This technique was developed by NASA for the development of thin sheet titanium and titanium aluminides used in high temperature applications. The materials investigated in this study included conventional titanium alloy strips and foils, Ti-1100, Ti-24Al-11Nb (Alpha-2), and Ti-48Al-2Ta (Gamma). The methodology used included micro-characterization, heat-treatment, mechanical processing and mechanical testing. Characterization techniques included optical, electron microscopy, and x-ray texture analysis. The processing included heat-treatment and mechanical deformation through cold rolling. The initial as-cast materials were evaluated for their microstructure and mechanical properties. Different heat-treatment and rolling steps were chosen to process these materials. The properties were evaluated further and a processing relationship was established in order to obtain an optimum processing condition. The results showed that the as-cast material exhibited a Widmanstatten (fine grain) microstructure that developed into a microstructure with larger grains through processing steps. The texture intensity showed little change for all processing performed in this investigation.

Source record↗

NASA NTRS1991

Evaluation of a hydrogen resistant titanium aluminide alloy

The Ti-24Al-11Nb (Ti-24-11) alloy heat treated to the fine basketweave microstructure was shown previously to be hydrogen tolerant. In order to assess its limit of hydrogen tolerance, the tensile, creep, fracture toughness, and sustained load crack growth behaviors of this alloy were studied as a function of hydrogen content. All test specimens were thermally charged with internal hydrogen and tested at 25 and 600 C. Coupon specimens were used for developing the hydrogen charging procedures and for studying compatibility of the alloy with high temperature, high pressure gaseous hydrogen. The mechanical test results indicated that the fine basketweave microstructure was tolerant to hydride embrittlement for hydrogen contents up to approximately 1500 wt. ppm, providing that the hydride formed was of the TiH2 type. On the other hand, hydrogen charging experiments indicated that the Ti-24-11 alloy was severely cracked and pulverized under zero load when the hydrogen content exceeded 3000 wt. ppm. X-ray diffraction results revealed that the dichotomous behaviors might be due to the formation of TiH(1.924) type hydrides at higher hydrogen contents. Thus, hydrogen embrittlement in the Ti-24-11 alloy with the fine basketweave microstructure depends on hydrogen content and the nature of the hydrides formed.

Chan, K. S.↗

NASA NTRS2003

High Conductivity Materials for High Heat Flux Applications in Space Propulsion Systems

GRCop-84 is a new copper base alloy with an excellent combination of strength and conductivity and has been developed to the point that it is a strong candidate for near term rocket engine applications. This work sought to establish the feasibility of new alloys with capabilities beyond GRCop-84. The use of coatings as environmental and thermal barriers adds further capability into the Copper base structure. Finally, Nickel-Aluminum based systems have also been explored.

Nathal, M. V.↗

NASA NTRS1985

Material technology

Advanced high pressure O2/H2 propulsion systems as exemplified by the Space Shuttle Main Engine (SSME) create challenging operating environments for materials. Many components operate in either hydrogen or hydrogen-steam environments which may significantly degrade the performance of common alloys. The objective of the materials technology projects is to develop and evaluate candidate materials for application in advanced high pressure O2/H2 propulsion systems. These new and improved materials are to improve the durability or performance of the SSME or derivative engine. The program includes projects on the following topics: (1) Hydrogen Resistant Alloys; (2) High Pressure O2 Ignition and Burning; (3) Improved Turbine Blades; (4) Improved Turbine Disk Material; (5) Impact Reactivity in High Pressure O2; and Fiber Reinforced Superalloys.

Dreshfield, R. L.↗

NASA NTRS1998

Differential Thermal Analysis of Hg(1-x)Mn(x)Te Alloys in the X=0 to 0.3 Range

Understanding the experimental conditions necessary for the development of radial and axial compositional homogeneity in directionally solidified Hg(0.89)Mn(0.11)Te(MMT) crystals has been difficult due to the lack of segregation coefficient data on the Hg(1-x)Mn(x)Te alloy system in the X = 0 to 0.3 composition range. Determining segregation coefficient data from the available Hg(1-x)Mn(x)Te alloy phase equilibria data is not practical due to discrepancies in the shape of the reported solidus and liquidus curves in the X = 0 to 0.3 range. To resolve these discrepancies and to obtain segregation coefficient data which can be used to understand homogeneity in directionally solidified MMT crystals, the solidus and liquidus temperatures of seven Hg(1-x)Mn(x)Te alloys in the X = 0 to 0.3 range were determined using differential thermal analysis (DTA). The Hg(1-x)Mn(x)Te phase diagram constructed for the X = 0 to 0.3 range of this alloy system from the DTA measurements clarifies the shape of the solidus and liquidus curves in this range. The segregation coefficient for the Hg(1-x)Mn(x)Te system was found to vary from 5 to 4.4 as the solidus composition increased from 0-30 atomic percent MnTe. This information will be useful in the analysis of axial and radial homogeneity of directionally solidified MMT crystals.

Price, M. W.↗

NASA NTRS2019

Additive Manufacturing and Hot-Fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers Using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul R.↗

NASA NTRS2019

Additive Manufacturing and Hot-fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul↗

NASA NTRS1983

Refractory materials for high-temperature thermoelectric energy conversion

Theoretical work of two decades ago adequately explained the transport behavior and effectively guided the development of thermoelectric materials of high conversion efficiencies of conventional semiconductors (e.g., SiGe alloys). The more significant contributions involved the estimation of optimum doping concentrations, the reduction of thermal conductivity by solid solution doping and the development of a variety of materials with ZT approx. 1 in the temperature range 300 K to 1200 K. ZT approx. 1 is not a theoretical limitation although, experimentally, values in excess of one were not achieved. Work has continued with emphasis on higher temperature energy conversion. A number of promising materials have been discovered in which it appears that ZT 1 is realizable. These materials are divided into two classes: (1) the rare-earth chalcogenides which behave as itinerant highly-degenerate n-type semiconductors at room-temperature, and (2) the boron-rich borides, which exhibit p-type small-polaronic hopping conductivity.

Wood, C.↗

NASA NTRS1984

Refractory materials for high-temperature thermoelectric energy conversion

Theoretical work of two decades ago adequately explained the transport behavior and effectively guided the development of thermoelectric materials of high conversion efficiencies of conventional semiconductors (e.g., SiGe alloys). The more significant contributions involved the estimaiation of optimum doping concentrations, the reduction of thermal conductivity by solid solution doping and the development of a variety of materials with ZT approx. 1 in the temperature range 300 K to 1200 K. ZT approx. 1 is not a theoretical limitation although, experimentally, values in excess of one were not achieved. Work has continued with emphasis on higher temperature energy conversion. A number of promising materials have been discovered in which it appears that ZT 1 is realizable. These materials are divided into two classes: (1) the rare-earth chalcogenides which behave as itinerant highly-degenerate n-type semiconductors at room-temperature, and (2) the boron-rich borides, which exhibit p-type small-polaronic hopping conductivity.

Wood, C.↗

NASA NTRS1991

Predicting the oxidative lifetime of beta NiAl-Zr alloys

Nickel aluminides containing 40 to 50 at. pct Al and 0.1 at. pct Zr were studied following cyclic oxidation at 1400 C. The selective oxidation of Al resulted in the formation of protective Al2O3 scales on each alloy composition. However, repeated cycling eventually resulted in the gradual formation of less-protective NiAl2O4, first appearing on the 40Al alloys followed at longer times on the 45Al alloys. The appearance of the NiAl2O4, signaling the end of the protective scale-forming capability of the alloy, was related to the presence of gamma-prime (Ni3Al) which formed as a result of the loss of Al from the sample. A diffusion model, based on finite-difference techniques, was developed to predict the protective life of beta Ni-Al alloys. This model predicts Ni and Al concentration profiles after various oxidation exposures. The model can predict the oxidative lifetime due to Al depletion when the Al concentration decreases to a critical concentration. Measured Al concentration profiles on two alloys after various oxidation exposures are compared to those predicted by the diffusion model. The time to the appearance of the NiAl2O4 and that predicted by the diffusion model are compared and discussed.

Nesbitt, J. A.↗