Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

The Strength of Shell and Tubular Spar Wings

The report is a survey of the strength problems arising on shell and tubular spar wings. The treatment of the shell wing strength is primarily confined to those questions which concern the shell wing only; those pertaining to both shell wing and shell body together have already been treated in TM 838. The discussion of stress condition and compressive strength of shell wings and tubular spar wings is prefaced by several considerations concerning the spar and shell design of metal wings from the point of view of strength.

Ebner, H↗
NASA NTRS1993

Nonlinear aerodynamics and the design of wing tips

This contract began in April 1990 with studies on the effect of wingtip shape on induced drag. That work considered problems of determining induced drag from computational aerodynamic methods and examined effects of wake roll up on the induced drag of elliptical and crescent wings. The research contract was continued in April 1991 and again in April 1992 with scope augmented to include considerations other than induced drag. The idea was to develop methods for comparing wing tip shapes on the basis of their effects on total drag, structural weight, and high lift performance. To accomplish this, work was done to improve methods for multidisciplinary analysis and optimization of wings. This report describes results of research conducted from April 1992 through March 1993. The general objective was to improve an existing wing optimization method and apply the method to specific problems of interest. The method, while a valuable tool for wing tip design studies, can be applied to more general problems, and has been applied to some of these other problems during its development. Specific goals that were accomplished are listed below and are explained in more detail in attached reports: analysis methods were improved in the area of structural modeling; small improvements to the high lift model were made, and ideas were collected on how clean wing c(sub l(sub max)) should vary with sweep - these ideas should provide a guide for future examination of high lift with experiment or CFD; and a calculation for drag due to the loss of leading edge suction was added to the wing analysis.

Kroo, Ilan↗
NASA NTRS1993

Reduction of structural loads using maneuver load control on the Advanced Fighter Technology Integration (AFTI)/F-111 mission adaptive wing

A transonic fighter-bomber aircraft, having a swept supercritical wing with smooth variable-camber flaps was fitted with a maneuver load control (MLC) system that implements a technique to reduce the inboard bending moments in the wing by shifting the spanwise load distribution inboard as load factor increases. The technique modifies the spanwise camber distribution by automatically commanding flap position as a function of flap position, true airspeed, Mach number, dynamic pressure, normal acceleration, and wing sweep position. Flight test structural loads data were obtained for loads in both the wing box and the wing root. Data from uniformly deflected flaps were compared with data from flaps in the MLC configuration where the outboard segment of three flap segments was deflected downward less than the two inboard segments. The changes in the shear loads in the forward wing spar and at the roots of the stabilators also are presented. The camber control system automatically reconfigures the flaps through varied flight conditions. Configurations having both moderate and full trailing-edge flap deflection were tested. Flight test data were collected at Mach numbers of 0.6, 0.7, 0.8, and 0.9 and dynamic pressures of 300, 450, 600, and 800 lb/sq ft. The Reynolds numbers for these flight conditions ranged from 26 x 10(exp 6) to 54 x 10(exp 6) at the mean aerodynamic chord. Load factor increases of up to 1.0 g achieved with no increase in wing root bending moment with the MLC flap configuration.

Thornton, Stephen V.↗
NASA NTRS1994

Multirate flutter suppression system design for the Benchmark Active Controls Technology Wing

To study the effectiveness of various control system design methodologies, the NASA Langley Research Center initiated the Benchmark Active Controls Project. In this project, the various methodologies will be applied to design a flutter suppression system for the Benchmark Active Controls Technology (BACT) Wing (also called the PAPA wing). Eventually, the designs will be implemented in hardware and tested on the BACT wing in a wind tunnel. This report describes a project at the University of Washington to design a multirate flutter suppression system for the BACT wing. The objective of the project was two fold. First, to develop a methodology for designing robust multirate compensators, and second, to demonstrate the methodology by applying it to the design of a multirate flutter suppression system for the BACT wing. The contributions of this project are (1) development of an algorithm for synthesizing robust low order multirate control laws (the algorithm is capable of synthesizing a single compensator which stabilizes both the nominal plant and multiple plant perturbations; (2) development of a multirate design methodology, and supporting software, for modeling, analyzing and synthesizing multirate compensators; and (3) design of a multirate flutter suppression system for NASA's BACT wing which satisfies the specified design criteria. This report describes each of these contributions in detail. Section 2.0 discusses our design methodology. Section 3.0 details the results of our multirate flutter suppression system design for the BACT wing. Finally, Section 4.0 presents our conclusions and suggestions for future research. The body of the report focuses primarily on the results. The associated theoretical background appears in the three technical papers that are included as Attachments 1-3. Attachment 4 is a user's manual for the software that is key to our design methodology.

Berg, Martin C.↗
NASA NTRS1994

Crossflow instability control on a swept-wing: Preliminary studies

The pressure distribution on a swept wing causes the streamlines at the edge of the boundary layer to be curved. This pressure gradient normal to the external streamline creates a velocity component normal to the external streamline within the boundary layer which is referred to as the crossflow velocity. Because the crossflow velocity profile perpendicular to the wing surface has an inflection point, the profile is unstable. The stationary instability mode takes the form of crossflow vortices. Under these conditions, the boundary layer on the wing is extremely unstable and transition to turbulent flow takes place much closer to the leading edge of the wing than it would on an unswept wing. Higher skin friction drag is associated with turbulent flow, and so better aircraft performance could be obtained if the crossflow could be eliminated One method of controlling crossflow that is being investigated is boundary-layer suction. An extensive airfoil suction experiment in the 8 feet Transonic Pressure Tunnel (TPT) at NASA Langley Research Center will begin late in 1994. Because of the size, complexity, and expense associated with this test, a number of 'risk-reduction' tests are currently being conducted. The 20 x 28 in. Shear Flow Control Tunnel at NASA Langley is being used for some of these tests. Prior to the summer of 1994, a flat plate with a swept leading edge was installed in the 20 x 28 in. tunnel, with a displacement body mounted on the tunnel ceiling that created a pressure distribution on the plate similar to the pressure distribution on a swept wing. The flow over the plate was investigated during the summer of 1994 using a laser Doppler velocimeter (LDV) system. The LDV measurements indicated the possible presence of multiple disturbance modes, a rarely-seen phenomena since, in most tests, one disturbance mode dominates. The possible existence of multiple disturbance modes in the flat plate boundary layer, however, means that the flow in the 20 x 28 in. tunnel is of interest itself, and will be investigated more thoroughly in the future. With a view to these investigations, the boundary layer traverse mechanism in the 20 x 28 in. tunnel was modified to improve its performance, and strain gauges were mounted on the traverse in order to monitor its deflection during a test. Other preliminary work conducted in the 20 x 28 in. tunnel included the use of an infrared camera system. Previous work with this system showed that transition indeed could be detected, but the signal produced by the crossflow vortices was too weak to be detected. It was hoped that spraying the flat plate with naphthalene would augment the heat transfer associated with the crossflow vortices so that they would show up in a IR image; however, experiments showed that this would not work. Another set of tests was conducted in the 20 x 28 in. tunnel to determine the tripping requirements for a set of airfoil-shaped struts that will be used in the 8 feet TPT experiment. Since the Reynolds number associated with these struts is small, a laminar boundary layer would separate early, causing large fluctuations in the flow field. A turbulent boundary layer would remain attached further back, but tripping from laminar to turbulent flow at low Reynolds number is very difficult. However, trip strip configurations were found that should effectively trip the boundary layer at the required conditions. Currently underway is an investigation of the data acquisition requirements for the 8 feet TPT experiment, with the purpose of the finding the minimum amount of data needed to characterize sufficiently the swept-wing boundary layer. This study is being conducted using a numerically generated data set.

Bridges, David H.↗
NASA NTRS1995

Equivalent plate modeling for conceptual design of aircraft wing structures

This paper describes an analysis method that generates conceptual-level design data for aircraft wing structures. A key requirement is that this data must be produced in a timely manner so that is can be used effectively by multidisciplinary synthesis codes for performing systems studies. Such a capability is being developed by enhancing an equivalent plate structural analysis computer code to provide a more comprehensive, robust and user-friendly analysis tool. The paper focuses on recent enhancements to the Equivalent Laminated Plate Solution (ELAPS) analysis code that significantly expands the modeling capability and improves the accuracy of results. Modeling additions include use of out-of-plane plate segments for representing winglets and advanced wing concepts such as C-wings along with a new capability for modeling the internal rib and spar structure. The accuracy of calculated results is improved by including transverse shear effects in the formulation and by using multiple sets of assumed displacement functions in the analysis. Typical results are presented to demonstrate these new features. Example configurations include a C-wing transport aircraft, a representative fighter wing and a blended-wing-body transport. These applications are intended to demonstrate and quantify the benefits of using equivalent plate modeling of wing structures during conceptual design.

Giles, Gary L.↗
NASA NTRS1996

Correlation of Structural Analysis and Test Results for the McDonnell Douglas Stitched/RFI All-Composite Wing Stub Box

The analytical and experimental results of an all-composite wing stub box are presented in this report. The wing stub box, which is representative of an inboard portion of a commercial transport high-aspect-ratio wing, was fabricated from stitched graphite-epoxy material with a Resin Film Infusion manufacturing process. The wing stub box was designed and constructed by the McDonnell Douglas Aerospace Company as part of the NASA Advanced Composites Technology program. The test article contained metallic load-introduction structures on the inboard and outboard ends of the graphite-epoxy wing stub box. The root end of the inboard load introduction structure was attached to a vertical reaction structure, and an upward load was applied to the outermost tip of the outboard load introduction structure to induce bending of the wing stub box. A finite element model was created in which the center portion of the wing-stub-box upper cover panel was modeled with a refined mesh. The refined mesh was required to represent properly the geometrically nonlinear structural behavior of the upper cover panel and to predict accurately the strains in the stringer webs of the stiffened upper cover panel. The analytical and experimental results for deflections and strains are in good agreement.

Wang, John T.↗
NASA NTRS1959

Lift, Drag, and Pitching Moments of an Arrow Wing Having 80 Degree of Sweepback at Mach Numbers from 2.48 to 3.51 and Reynolds Numbers up to 11.0 Million

Measurements were made of the lift, drag, and pitching moments on an arrow wing (taper ratio of zero) having an aspect ratio of 1.4 and a leading-edge sweepback of 80 (degrees). The wing was designed to have a subsonic leading-edge and a Clark-Y airfoil with a thickness ratio of 12 percent of the chord perpendicular to the wing leading edge. The wing was tested both with and without the wing tips bent upward in an attempt to alleviate possible flow separation in the vicinity of the wing tips. Small jets of air were used to fix transition near the wing leading edge. Force results are presented for Mach numbers of 2.48, 2.75, 3.04, 3.28, and 3.51 at Reynolds numbers of 3.5 and 9.0 million and for a Mach number of 3.04 at a Reynolds number of 11.0 million. The measured aerodynamic characteristics are compared with those estimated by linear theory. The maximum lift-drag ratio measured was much less than that predicted. This difference is attributed to lack of full leading-edge thrust and to the experimental lift-curve slope being about 20 percent below the theoretical value.

Hopkins, Edward J.↗
NASA NTRS1960

Evaluation of Blended Wing-Body Combinations with Curved Plan Forms at Mach Numbers Up to 3.50

This investigation is a continuation of the experimental and theoretical evaluation of the effects of wing plan-form variations on the aerodynamic performance characteristics of blended wing-body combinations. The present report compares previously tested straight-edged delta and arrow models which have leading-edge sweeps of 59.04 and 70-82 deg., respectively, with related models which have plan forms with curved leading and trailing edges designed to result in the same average sweeps in each case. All the models were symmetrical, without camber, and were generally similar having the same span, length, and aspect ratios. The wing sections had an average value of maximum thickness ratio of about 4 percent of the local wing chords in a streamwise direction. The wing sections were computed by varying their shapes along with the body radii (blending process) to match the selected area distribution and the given plan form. The models were tested with transition fixed at Reynolds numbers of roughly 4,000,000 to 9,000,000, based on the mean aerodynamic chord of the wing. The characteristic effect of the wing curvature of the delta and arrow models was an increase at subsonic and transonic speeds in the lift-curve slopes which was partially reflected in increased maximum lift-drag ratios. Curved edges were not evaluated on a diamond plan form because a preliminary investigation indicated that the curvature considered would increase the supersonic zero-lift wave drag. However, after the test program was completed, a suitable modification for the diamond plan form was discovered. The analysis presented in the appendix indicates that large reductions in the zero-lift wave drag would be obtained at supersonic Mach numbers if the leading- and trailing-edge sweeps are made to differ by indenting the trailing edge and extending the root of the leading edge.

Holdaway, George H.↗
NASA NTRS1960

The Shock-Wave Patterns on a Cranked-Wing Configuration

The shock-wave patterns of a complex configuration with cranked cruciform wings and a cone-cylinder body were examined to determine the interaction of the body bow wave with the flow field about the wing. Also of interest, was the interaction of the forward (760 sweptback) wing leading-edge wave with the rear (600 sweptback) wing leading-edge wave. The shadowgraph pictures of the model in free flight at a Mach number of 4.9, although not definitive, appear to indicate that the body bow wave crosses the outer wing panel after first being refracted either by the leading-edge wave of the 600 sweptback wing or by pressure fields in the flow crossing the wing.

Sammonds, Robert I.↗
NASA NTRS1959

Effects of Cross-Sectional Shape, Solidity, and Distribution of Heat-Transfer Coefficient on the Torsional Stiffness of Thin Wings Subjected to Aerodynamic Heating

A study has been made of the effects of varying the shape, solidity, and heat-transfer coefficient of thin wings with regard to their influence on the torsional-stiffness reduction induced by aerodynamic heating. The variations in airfoil shape include blunting, flattening, and combined blunting and flattening of a solid wing of symmetrical double-wedge cross section. Hollow double-wedge wings of constant skin thickness with and without internal webs also are considered. The effects of heat-transfer coefficients appropriate for laminar and turbulent flow are investigated in addition to a step transition along the chord from a lower to a higher constant value of heat-transfer coefficient. From the results given it is concluded that the flattening of a solid double wedge decreases the reduction in torsional stiffness while slight degrees of blunting increase the loss. The influence of chordwise variations in heat-transfer coefficient due to turbulent and laminar boundary-layer flow on the torsional stiffness of solid wings is negligible. The effect of a step transition in heat-transfer coefficient along the chord of a solid wing can, however, become appreciable. The torsional-stiffness reduction of multiweb and hollow double-wedge wings is substantially less than that calculated for a solid wing subjected to the same heating conditions.

Thomson, Robert G.↗
NASA NTRS1961

Effects of Canard Planform and Wing-Leading-Edge Modification on Low-Speed Longitudinal Aerodynamic Characteristics of a Canard Airplane Configuration

An investigation has been conducted at low subsonic speeds to study the effects of canard planform and wing-leading-edge modification on the longitudinal aerodynamic characteristics of a general research canard airplane configuration. The basic wing of the model had a trapezoidal planform, an aspect ratio of 3.0, a taper ratio of 0.143, and an unswept 80-percent-chord line. Modifications to the wing included addition of full-span and partial-span leading-edge chord-extensions. Two canard planforms were employed in the study; one was a 60 deg sweptback delta planform and the other was a trapezoidal planform similar to that of the basic wing. Modifications to these canards included addition of a full-span leading-edge chord-extension to the trapezoidal planform and a fence to the delta planform. For the basic-wing-trapezoidal-canard configuration, rather abrupt increases in stability occurred at about 12 deg angle of attack. A slight pitch-up tendency occurred for the delta-canard configuration at approximately 8 deg angle of attack. A comparison of the longitudinal control effectiveness for the basic-wing-trapezoidal-canard combination and for the basic-wing-delta-canard combination indicates higher values of control effectiveness at law angles of attack for the trapezoidal canard. The control effectiveness for the delta-canard configuration, however, is seen to hold up for higher canard deflections and to higher angles of attack. Use of a full-span chord-extension deflected approximately 30 deg on the trapezoidal canard greatly improved the control characteristics of this configuration and enabled a sizeable increase in trim lift to be realized.

Spencer, Bernard, Jr.↗
NASA NTRS1960

The Longitudinal Aerodynamic Characteristics of a Sweptback Wing-Body Combination With and Without End Plates at Mach Numbers from 0.40 to 0.93

An investigation was made at high subsonic speeds in the Langley high-speed 7- by 10-foot tunnel to determine the effect of end plates on the longitudinal aerodynamic characteristics of a sweptback wing-body combination with and without drooped chord-extensions. The wing had 45 deg sweepback of the quarter-chord line, an aspect ratio of 4, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry, and was mounted near the rear of a body of revolution having a fineness ratio of approximately 8. The results indicated that the addition of the end plates to either the wing with drooped chord-extensions or to the wing without drooped chord-extensions slightly increased the lift in the low angle-of-attack range but slightly decreased the lift at moderate and high angles of attack. The addition of the end plates to the wing without the chord-extensions caused a small increase in the maximum lift-drag ratio at Mach numbers below 0.65 and a slight decrease at the higher Mach numbers; however, for the addition of the end plates to the wing with the chord- extensions the maximum lift-drag ratio was slightly decreased below a Mach number of 0.88, while a slight increase occurred for the higher Mach numbers. The addition of the end plates to the wings with and without the chord-extensions caused the static longitudinal stability to increase considerably for all Mach numbers; however, only a slight reduction in the aerodynamic-center variation with Mach number was observed.

Henderson, William P.↗
NASA NTRS1961

Aerodynamic Characteristics of Low-Aspect-Ratio Wings in Close Proximity to the Ground

A wind-tunnel investigation has been conducted to determine the effect of ground proximity on the aerodynamic characteristics of thick highly cambered rectangular wings with aspect ratios of 1. 2, 4, and 6. The results showed that, for these aspect ratios, as the ground war, approached all wings experienced increases in lift-curve slope and reductions in induced drag which resulted in increases in lift-drag ratio. Although an increase in lift-curve slope was obtained for all aspect ratios as the ground was approached, the lift coefficient at an angle of attack of 0 deg for any given aspect ratio remained nearly constant. The experimental results were in general agreement with Wieselsberger's ground-effect theory (NACA Technical Memorandum 77). As the wings approached the ground, there was an increase in static longitudinal stability at positive angles of attack. When operating in ground effect, all the wings had stability of height at positive angles of attack and instability of height at negative angles of attack. Wing-tip fairings on the wings with aspect ratios of 1 and 2 produced small increases in lift-drag ratio in ground effect. End plates extending only below the chord plane on the wing with an aspect ratio of 1 provided increases in lift coefficient and in lift-drag ratio in ground effect.

Fink, Marvin P.↗
NASA NTRS1961

Static Lateral Characteristics at High Subsonic Speeds of a Complete Airplane Model with a Highly Tapered Wing having the 0.80 Chord Line Unswept and with Several Tail Configurations

An investigation was made at high subsonic speeds of a complete model having a highly tapered wing and several tail configurations. The aspect-ratio-3.50 wing had a taper ratio of 0.067 and an unswept 0.80 chord line. The complete model was tested with a wing-chord-plane tail, a T-tail, and a biplane tail (combined T-tail and wing-chord-plane tail). The model was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92 over a range of angle of attack of about +/- 20 deg. and a range of sideslip of -15 deg. to 13 deg. Some data were obtained with the horizontal stabilizer deflected. A few tests were also made with the wing tips clipped to an aspect ratio of 3.00. The data show that shock-interference effects between the tail surfaces (T-tail) can have considerable influence on the directional stability and effective dihedral. For example, the T-tail configuration with horizontal-tail leading-edge overhang showed a considerable loss in directional stability as the angle of attack was reduced to zero or negative values; whereas, the T-tail with zero leading-edge overhang showed the loss to be considerably less. The directional stability of the model with the low tail was essentially constant over a range of angle of attack of +/- 50 deg. All configurations tested showed a large reduction in stability at positive and negative angles of attack larger than about 15 deg., probably because of adverse sidewash associated with wing stall. The data show that a wing-chord-plane horizontal tail (low tail) tends to give a positive pitching-moment increment with increase in sideslip angle; whereas, a high tail (T-tail) tends to give negative increments in pitching moment.

Goodson, Kenneth W.↗
NASA NTRS1959

Free-Flight Investigation of a Rocket-Propelled Model to Determine the Aerodynamic Heating on a Thin, Unswept, Untapered, Multispar, Aluminum-Alloy Wing at Mach Numbers up to 2.22

A free-flight investigation has been made to determine some effects of aerodynamic heating on the structural behavior of a wing at supersonic speeds. The test wing was a thin, unswept, untapered, multispar, aluminum-alloy wing having a 20-inch chord, a 20-inch exposed semispan, and a circular-arc airfoil section with a thickness ratio of 5 percent. The wing was tested on a model propelled by a two-stage rocket-propulsion system to a Mach number of 2.22 and a corresponding Reynolds number per foot of 13.2 x 10(6) Reasonably good agreement was obtained between Stanton numbers obtained from measured temperature-time data and values obtained by the theory of Van Driest for flat plates having turbulent boundary layers. Temperature measurements made in the skin of the wing and in the internal structures agreed well with calculated values. The wing was instrumented to detect any apparent fluttering motion in the wing, but no evidence of flutter was observed throughout the flight.

Stephens, Emily W.↗
NASA NTRS1959

Investigation at Mach Numbers of 0.20 to 3.50 of a Blended Diamond Wing and Body Combination of Sonic Design but with Low Wave-Drag Increase with Increasing Mach Number

A diamond wing and body combination was designed to have an area distribution which would result in near optimum zero-lift wave-drag coefficients at a Mach number of 1.00, and decreasing wave-drag coefficient with increasing Mach number up to near sonic leading-edge conditions for the wing. The airfoil section were computed by varying their shape along with the body radii (blending process) to match the selected area distribution and the given plan form. The exposed wing section had an average maximum thickness of about 3 percent of the local chords, and the maximum thickness of the center-line chord was 5.49 percent. The wing had an aspect ratio of 2 and a leading-edge sweep of 45 deg. Test data were obtained throughout the Mach number range from 0.20 to 3.50 at Reynolds numbers based on the mean aerodynamic chord of roughly 6,000,000 to 9,000,000. The zero-lift wave-drag coefficients of the diamond model satisfied the design objectives and were equal to the low values for the Mach number 1.00 equivalent body up to the limit of the transonic tests. From the peak drag coefficient near M = 1.00 there was a gradual decrease in wave-drag coefficient up to M = 1.20. Above sonic leading-edge conditions of the wing there was a rise in the wave-drag coefficient which was attributed in part to the body contouring as well as to the wing geometry. The diamond model had good lift characteristics, in spite of the prediction from low-aspect-ratio theory that the rear half of the diamond wing would carry little lift. The experimental lift-curve slope obtained at supersonic speeds were equal to or greater than the values predicted by linear theory. Similarly the other basic aerodynamic parameters, aerodynamic center position, and maximum lift-drag ratios were satisfactorily predicted at supersonic speeds.

Holdaway, George H.↗
NASA NTRS1992

Aerodynamic Spring and Damping of Free-Pitching Tips on a Semispan Wing

A test was conducted in the NASA Ames 7- by 10-Foot Wind Tunnel to derive aerodynamic spring and damping estimates for free-pitching tips on a semispan wing. The test model was a rectangular planform semispan wing with wing tips that had a single rigid-body pitch degree of freedom with respect to the inboard wing. A number of different tip planform geometries were tested, incorporating a range of quarter-chord sweep angles and taper ratios. The wing-tip dynamic response characteristics were measured at several wing angles of attack and tunnel dynamic pressures. The tip oscillations were initiated by releasing the tips from prescribed angles of attack. A new method to isolate Coulomb damping from aerodynamic damping from these tip-motion time histories is developed and applied. Correlations were performed between the experimentally derived wing-tip aerodynamic spring and damping values and predictions from a semiempirical analysis based on steady-state tip aerodynamic loads.

Young, Larry A.↗