Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

The salutary effect of dietary calcium on bone mass in a rat model of simulated weightlessness

Whether supplementation of dietary calcium reduces the differences in bone mass of unweighed limbs and normally weighted limbs, and whether parathyroid hormone (PTH) and 1,25-dihydroxyvitamin D (1,25(OH)2D) respond differently to dietary calcium in unweighted animals in comparison with pair-fed controls was studied. The hind limbs of rats were unweighted by a tail suspension method and diets containing 0.1% to 2.4% calcium. After 2 weeks serum calcium, phosphorus, PTH and 1,25(OH)2D intestinal calcium transport were determined and bone mass, ash weight, and calcium in the tibia, L-1 vertebra, and humerus were measured. No significant differences in body weights were observed among the various groups. Suspended rats maintained constant levels of serum calcium and phosphate over the wide range of dietary calcium. Serum PTH and 1,25(OH)2D and intestinal calcium transport fell as dietary calcium was increased. Bone calcium in the tibia and vertebra from suspended rats remained less than that from pair-fed control. It is suggested that although no striking difference between suspended and control animals was observed in response to dieteary calcium, increasing dietary calcium may reduce the negative impact of unloading on the calcium content of the unweighted bones. The salutary effect of high dietary calcium appears to be due to inhibition of bone resorption rather than to stimulation of bone formation.

Bikle, D. D.↗

A review of path-independent integrals in elastic-plastic fracture mechanics, task 4

The path independent (P-I) integrals in elastic plastic fracture mechanics which have been proposed in recent years to overcome the limitations imposed on the J integral are reviewed. The P-I integrals considered herein are the J integral by Rice, the thermoelastic P-I integrals by Wilson and Yu and by Gurtin, the J* integral by Blackburn, the J sub theta integral by Ainsworth et al., the J integral by Kishimoto et al., and the delta T sub p and delta T* sub p integrals by Atluri et al. The theoretical foundation of these P-I integrals is examined with emphasis on whether or not path independence is maintained in the presence of nonproportional loading and unloading in the plastic regime, thermal gradients, and material inhomogeneities. The similarities, differences, salient features, and limitations of these P-I integrals are discussed. Comments are also made with regard to the physical meaning, the possibility of experimental measurement, and computational aspects.

Kim, K. S.↗

Theoretical model of impact damage in structural ceramics

This paper presents a mechanistically consistent model of impact damage based on elastic failures due to tensile and shear overloading. An elastic axisymmetric finite element model is used to determine the dynamic stresses generated by a single particle impact. Local failures in a finite element are assumed to occur when the primary/secondary principal stresses or the maximum shear stress reach critical tensile or shear stresses, respectively. The succession of failed elements thus models macrocrack growth. Sliding motions of cracks, which closed during unloading, are resisted by friction and the unrecovered deformation represents the 'plastic deformation' reported in the literature. The predicted ring cracks on the contact surface, as well as the cone cracks, median cracks, radial cracks, lateral cracks, and damage-induced porous zones in the interior of hot-pressed silicon nitride plates, matched those observed experimentally. The finite element model also predicted the uplifting of the free surface surrounding the impact site.

Liaw, B. M.↗

Magnetotail energy storage and release during the CDAW 6 substorm analysis intervals

The concept of the Coordinated Data Analysis Workshop (CDAW) grew out of the International Magnetospheric Study (IMS) program. According to this concept, data are to be pooled from a wide variety of spacecraft and ground-based sources for limited time intervals. These data are to provide the basis for the performance of very detailed correlative analyses, usually with fairly limited physical problems in mind. However, in the case of the CDAW 6 truly global goals are involved. The primary goal is to trace the flow of energy from the solar wind through the magnetosphere to its ultimate dissipation by substorm processes. The present investigation has the specific goal to examine the evidence for the storage of solar wind energy in the magnetotail prior to substorm expansion phase onsets. Of particular interest is the determination, in individual substorm cases, of the time delays between the loading of energy into the magnetospheric system and the subsequent unloading of this energy.

Baker, D. N.↗

Energy supply processes for magnetospheric substorms and solar flares - Tippy bucket model or pitcher model?

In the past, both magnetospheric substorms and solar flares have almost exclusively been discussed in terms of explosive magnetic reconnection. Such a model may conceptually be illustrated by the so-called 'tippy-bucket model', which causes sudden unloading processes, namely a sudden (catastrophic, stochastic, and unpredictable) conversion of stored magnetic energy. However, recent observations indicate that magnetospheric substorms can be understood as a result of a directly driven process which can conceptually be illustrated by the 'pitcher model' in which the output rate varies in harmony with the input rate. It is also possible that solar flare phenomena are directly driven by a photospheric dynamo. Thus, explosive magnetic reconnection may simply be an unworkable hypothesis and may not be a puzzle to be solved as the primary energy supply process for magnetospheric substorms and solar flares.

Akasofu, S.-I.↗

Bone and muscle atrophy with suspension of the rat

In order to identify a suitable model for the study of muscle atrophy due to suspension in space, a modified version of the Morey tail suspension model was used to measure the atrophic responses of rat bone and muscle to 14-30 days of unloading of the hindlimbs. The progress of atrophy was measured by increases in methylene diphosphonate (MDP) uptake. It is found that bone uptake of methylene diphosphonate followed a phasic pattern similar to changes in the bone formation rate of immobilized dogs and cats. Increased MDP uptake after a period of 60 days indicated an accelerated bone metabolism. Maximum muscle atrophy in the suspended rats was distinctly different from immobilization atrophy. On the basis of the experimental results, it is concluded that the tail suspension model is an adequate simulation of bone atrophy due to suspension.

Leblanc, A.↗

Magnetospheric impulse response for many levels of geomagnetic activity

The temporal relationship between the solar wind and magnetospheric activity has been studied using 34 intervals of high time resolution IMP 8 solar wind data and the corresponding AL auroral activity index. The median values of the AL index for each interval were utilized to rank the intervals according to geomagnetic activity level. The linear prediction filtering technique was then applied to model magnetospheric response as measured by the AL index to the solar wind input function VB(s). The linear prediction filtering routine produces a filter of time-lagged response coefficients which estimates the most general linear relationship between the chosen input and output parameters of the magnetospheric system. It is found that the filters are composed of two response pulses speaking at time lags of 20 and 60 min. The amplitude of the 60-min pulse is the larger for moderate activity levels, while the 20-min pulse is the larger for strong activity levels. A possible interpretation is that the 20-min pulse represents magnetospheric activity driven directly by solar wind coupling and that the 60-min pulse represents magnetospheric activity driven by the release of energy previously stored in the magnetotail. If this interpretation is correct, the linear filtering results suggest that both the driven and the unloading models of magnetospheric response are important facets of a more comprehensive response model.

Bargatze, L. F.↗

Response to muscular exercise following repeated simulated weightlessness

The effects of 10-d 6-deg-head-down bed rest (BR1), 14 d of recovery, another 10 d bed rest (BR2), and another 14-d recovery on the cardiovascular response to a graded supine cycle ergometer test (4 min unloaded 60-rpm pedaling followed by 15-W/min increasing work load to volitional fatigue) are investigated experimentally in seven male nonsmokers of mean age 41 yrs, mean weight 80.2 kg, mean height 178 cm, and mean body fat content 22.3 percent. Ergometer tests are performed before BR1, after BR1 and BR2, and 14 d after BR2. The results are presented in tables, and it is found that the significantly decreased maximum-O2-uptake, gas-exchange-aerobic-threshold, and plasma-volume responses and the increased submaximal and maximal heart rates observed (relative to pre-BR1 levels) after BR1 and BR2 return to pre-BR1 values 14 d after BR2. It is inferred that 14 d of mild exercise are adequate for recovery from even repeated exposure to this type of simulated weightlessness.

Convertino, V. A.↗

A survey of strength analysis methods for laminates with holes

The methods for predicting the strength of composite laminates with fastener holes are reviewed for the cases of unloaded as well as loaded holes. Three categories of methods are discussed: (1) the hole-boundary stress (HBS) methods which compare the peak stresses and the laminate strength; (2) the linear elastic fracture (LEFM) methods which assume cracks emanating from the hole and predict failure when the stress intensity factor for a crack equals the laminate fracture toughness; and (3) two different two-parameter (TP) methods: the average-stress (ASTP) method, which predicts failure when the average stress over a distance from the hole equals the laminate strength; and the point-stress (PSTP) Whitney-Nuismer (1974) approach, which predicts failure when the stress near the hole equals the material strength. The PSTP is relatively accurate and is by far the most widely used of all the prediction methods. However, for large ranges of variables and cases, the current strength predictions may not always be accurate.

Crews, J. H., Jr.↗

Linear Phase Modulator

Circuit suppresses AM component while providing matched input impedance. Phase modulation uses reflective properties of series resonant tank to reflect all of signal except for small amount in unloaded Q of coils and varactor diode. Circuit used in payload integrator of Space Shuttle S-band communications and tracking equipment, has applications in other communications and tracking equipment.

Hesse, R. H.↗

Elastic-plastic deformation of a metal-matrix composite coupon with a center slot

A comprehensive experimental analysis of deformations of the surface of a metal-matrix specimen is reported. The specimen is a 6-ply 0 + or - 45 sub s boron-aluminum tensile coupon with a central slot. Moire interferometry is used for high-sensitivity whole-field measurements of in-plane displacements. Normal and shear strains are calculated from displacement gradients. Displacement fields are analyzed at various load levels from 15% to 95% of the failure load. Deformations of the boron fibers could be distinguished from those of the matrix. Highly localized plastic slip zones occur tangent to the ends of the slot. Shear strains and concurrent transverse compressive strains in the slip zones reach approximately 10% and 1%, respectively. Upon unloading, elastic recovery in surrounding regions causes a reverse plastic shear strain in the slip zone of about 4%. Longitudinal normal strains on the unslotted ligament peak at the slot boundary at about 1% strain. The strain concentration factor at the end of the slot decreases with load level and the advance of plasticity.

Post, D.↗

Low-cycle thermal fatigue

A state-of-the-art review is presented of the field of thermal fatigue. Following a brief historical review, the concept is developed that thermal fatigue can be viewed as processes of unbalanced deformation and cracking. The unbalances refer to dissimilar mechanisms occurring in opposing halves of thermal fatigue loading and unloading cycles. Extensive data summaries are presented and results are interpreted in terms of the unbalanced processes involved. Both crack initiation and crack propagation results are summarized. Testing techniques are reviewed, and considerable discussion is given to a technique for thermal fatigue simulation, known as the bithermal fatigue test. Attention is given to the use of isothermal life prediction methods for the prediction of thermal fatigue lives. Shortcomings of isothermally-based life prediction methods are pointed out. Several examples of analyses and thermal fatigue life predictions of high technology structural components are presented. Finally, numerous dos and don'ts relative to design against thermal fatigue are presented.

Halford, G. R.↗

Remotely operable peristaltic pump

A peristaltic pump is disclosed which includes a roller assembly on which is mounted a series of pump rollers. As the roller assembly is rotated by a drive gear the pump rollers are driven in reverse rotation by means of a stationary ring gear and pump roller gears. An upper pressure shoe plate and a lower pressure shoe plate are positioned above sets of flexible tubing. The tubing is sandwiched between the pressure shoe plates and the pump rollers. A highly compact pump is provided having twice as many fluid channel lines as is conventional. The peristaltic pump device may be remotely operated by means of a rotary actuator which rotates a driving hub to move the shoe plates by means of eccentrically mounted links. The pressure shoe plates may be moved by the rotary actuator to a loaded position in which the fluid lines are pinched by the pump rollers and fluid is pumped to an unloaded position in which the fluid lines are maintained in an undeformed, uncrimped configuration so that no creases or crimps are set into the fluid lines during periods of prolonged nonuse.

Belew, R. R.↗

The effect of slots on the buckling and postbuckling behavior of laminated plates

An experimental study was conducted to evaluate the effect of lateral slots on the buckling response, the postbuckling response, and the failure characteristics of flat rectangular graphite-epoxy plates loaded in compression. The slots did not significantly affect the prebuckling and buckling behavior of the plates. The slots caused local changes in the strain distribution and out-of-plane deformations near the slot. Failure loads and modes were strongly affected by slot location. Centrally located slots did not affect the failure loads or failure modes of the plates. Slots located close to an unloaded edge of a plate reduced the postbuckling strength of the plate and affected the failure mode. For one slightly offset slot location, interaction of out-of-plane deformations with the slot tip was observed to affect the failure mode significantly without affecting the failure load.

Gurdal, Z.↗

Recent studies of energy integrals and their applications

In this paper, recent studies concerning path independent integrals, of relevance in the fracture of solids, and the applications of these integrals, are critically summarized. Specific topics dealt with include: (1) unsteady dynamic crack-propagation in (nonlinear) elastic solids and (2) slow stable, as well as fast crack propagation in elastic-plastic materials, which are characterized by an (incremental) flow theory of plasticity, and which are subject to arbitrary loading (and unloading) histories.

Atluri, S. N.↗

Spaceflight and calcium metabolism

Calcium metabolism data from spaceflight have been obtained primarily from Skylab astronauts, from Soviet Salyut-6 cosmonauts, and from growing rats flown either on the Soviet Cosmos series or Spacelab 3. In this report, the results from Skylab astronauts will be compared to data from bed rested subjects, and the results from Cosmos rats will be compared to data from a ground-based rat model, to help explain (1) how spaceflight or gravitational unloading alters calcium metabolism in adult humans and growing rats, (2) the relevance of the observations of bone dynamics in growing rats to the changes in adult man, and (3) the sequence of events leading to changes in calcium metabolism during spaceflight. A hypothetical scheme of the mechanisms causing altered bone mass during spaceflight will be proposed.

Morey-Holton, E. R.↗

Effect of seven days of spaceflight on hindlimb muscle protein, RNA and DNA in adult rats

Effects of seven days of spaceflight on skeletal muscle (soleus, gastrocnemius, EDL) content of protein, RNA and DNA were determined in adult rats. Whereas total protein contents were reduced in parallel with muscle weights, myofibrillar protein appeared to be more affected. There were no significant changes in absolute DNA contents, but a significant (P less than 0.05) increase in DNA concentration (microgram/milligram) in soleus muscles from flight rats. Absolute RNA contents were significantly (P less than 0.025) decreased in the soleus and gastrocnemius muscles of flight rats, with RNA concentrations reduced 15-30 percent. These results agree with previous ground-based observations on the suspended rat with unloaded hindlimbs and support continued use of this model.

Steffen, J. M.↗

Flexibility effects on tooth contact location in spiral bevel gear transmissions

An analytical method to predict the shift of the contact ellipse between the meshing teeth in a spiral bevel gear set is presented in this report. The contact ellipse shift of interest is the motion of the nominal tooth contact location on each tooth from the ideal pitch point to the point of contact between the two teeth considering the elastic motions of the gears and their supporting shafts. This is the shift of the pitch point from the ideal, unloaded position on each tooth to the nominal contact location on the tooth when the gears are fully loaded. It is assumed that the major contributors of this motion are the elastic deflections of the gear shafts, the slopes of the shafts under load and the radial deflections of the four gear shaft bearings. The motions of the two pitch point locations on the pinion and the gear tooth surfaces are calculated in a FORTRAN program which also calculates the size and orientation of the Hertzian contact ellipse on the tooth faces. Based on the curvatures of the two spiral bevel gear teeth and the size of the contact ellipse, the program also predicts the basic dynamic capacity of the tooth pair. A complete numerical example is given to illustrate the use of the program.

Altidis, P. C.↗