Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Tm”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

The 16 September 1986 eruption of Lascar volcano, north Chile - Satellite investigations

The features of the September 16, 1986 small-volume high-intensity eruption of Lascar volcano (Chile) were investigated using remote sensing data. Ground observations and conventional geological studies provided only minor information on this event. Examinations of Landsat Thematic Mapper (TM) images showed that the pronounced thermal anomaly recorded on TM images in 1984 and 1985 became weaker after the eruption on September 16, 1986, and divided into several sources. Field investigations and images obtained by GOES confirm that the September 16 event was a short-lived volcanic eruption which produced an ash column reaching 15 km altitude. Transport occurred in the upper troposphere at speeds up to 180 km/h. Ash fall from the plume was well sorted and moderately fine-grained (MD 200 microns).

Glaze, L. S.↗
NASA NTRS1989

Mapping surface energy balance components by combining Landsat Thematic Mapper and ground-based meteorological data

Surface energy balance components were evaluated by combining satellite-based spectral data with on-site measurements of solar irradiance, air temperature, wind speed, and vapor pressure. Maps of latent heat flux density and net radiant flux density were produced using Landsat TM data for three dates. The TM-based estimates differed from Bowen-ratio and aircraft-based estimates by less than 12 percent over mature fields of cotton, wheat, and alfalfa.

Moran, M. Susan↗
NASA NTRS1990

Diagnostic evaluations of microwave generated helium and nitrogen plasma mixtures

The goal of this work is to continue the development to fundamentally understand the plasma processes as applied to spacecraft propulsion. The diagnostic experiments used are calorimetric, dimensional, and spectroscopic measurements using the TM 011 and TM 012 modes in the resonance cavity. These experimental techniques are highly important in furthering the understanding of plasma phenomena and of designing rocket thrusters. Several experimental results are included using nitrogen and helium gas mixtures.

Haraburda, Scott S.↗
NASA NTRS1990

Geocoding and stereo display of tropical forest multisensor datasets

Concern about the future of tropical forests has led to a demand for geocoded multisensor databases that can be used to assess forest structure, deforestation, thermal response, evapotranspiration, and other parameters linked to climate change. In response to studies being conducted at the Braulino Carrillo National Park, Costa Rica, digital satellite and aircraft images recorded by Landsat TM, SPOT HRV, Thermal Infrared Multispectral Scanner, and Calibrated Airborne Multispectral Scanner sensors were placed in register using the Landsat TM image as the reference map. Despite problems caused by relief, multitemporal datasets, and geometric distortions in the aircraft images, registration was accomplished to within + or - 20 m (+ or - 1 data pixel). A digital elevation model constructed from a multisensor Landsat TM/SPOT stereopair proved useful for generating perspective views of the rugged, forested terrain.

Welch, R.↗
NASA NTRS1991

Effects of long term exposure on optical substrates and coatings (SOO50-1)

The experiment consisted of fused silica and ultra low expansion (ULE(tm)) glass samples which were either uncoated or had high reflectance silver, antireflectance, or solar rejection coatings. A set of duplicate control samples was manufactured and stored in a controlled environment for comparison purposes. Data on the analysis of the contaminate deposited on the samples, micrometeoroid impact, and the environmental effects on the substrate materials and coatings are presented. Some results of particular interest are that the contaminate composition varied between different types of samples, fractures were incurred in the glass at the micrometeoroid impact site, and no darkening of the ULE(tm) glass occurred due to the radiation exposure.

Vallimont, John↗
NASA NTRS1991

The corrosion protection of 2219-T87 aluminum by anodizing

Various types of anodizing coatings were studied for 2219-T87 aluminum. These include both type II and type III anodized coats which were water sealed and a newly developed and proprietary Magnaplate HCR (TM) coat. Results indicate that type II anodizing is not much superior to type II anodizing as far as corrosion protection for 2219-T87 aluminum is concerned. Magnaplate HCR (TM) coatings should provide superior corrosion protection over an extended period of time using a coating thickness of 51 microns (2.0 mils).

Danford, M. D.↗
NASA NTRS1991

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

The addition of ceramic particles to aluminum based alloys can substantially improve mechanical properties, especially Young's modulus and room and elevated temperature strengths. However, these improvements typically occur at the expense of tensile ductility. The mechanical properties are evaluated to a metal matrix composite (MMC) consisting of an ultrahigh strength aluminum lithium alloy, Weldalite (tm) 049, reinforced with TiB2 particles produced by an in situ precipitation technique called the XD (tm) process. The results are compared to the behavior of a nonreinforced Weldalite 049 variant. It is shown that both 049 and 049-TiB2 show very attractive warm temperature properties e.g., 625 MPa yield strength at 150 C after 100 h at temperature. Weldalite 049 reinforced with a nominal 4 v pct. TiB2 shows an approx. 8 pct. increase in modulus and a good combination of strength (529 MPa UTS) and ductility (6.5 pct.) in the T3 temper. And the high ductility of Weldalite 049 in the naturally aged and underaged tempers makes the alloy a good, high strength matrix for ceramic reinforcement.

Source record↗
NASA NTRS1990

Approach to transaction management for Space Station Freedom

The Space Station Freedom Manned Base (SSFMB) will support the operation of the many payloads that may be located within the pressurized modules or on external attachment points. The transaction management (TM) approach presented provides a set of overlapping features that will assure the effective and safe operation of the SSFMB and provide a schedule that makes potentially hazardous operations safe, allocates resources within the capability of the resource providers, and maintains an environment conducive to the operations planned. This approach provides for targets of opportunity and schedule adjustments that give the operators the flexibility to conduct a vast majority of their operations with no conscious involvement with the TM function.

Easton, C. R.↗
NASA NTRS1989

Simple models for complex natural surfaces - A strategy for the hyperspectral era of remote sensing

A two-step strategy for analyzing multispectral images is described. In the first step, the analyst decomposes the signal from each pixel (as expressed by the radiance or reflectance values in each channel) into components that are contributed by spectrally distinct materials on the ground, and those that are due to atmospheric effects, instrumental effects, and other factors, such as illumination. In the second step, the isolated signals from the materials on the ground are selectively edited, and recombined to form various unit maps that are interpretable within the framework of field units. The approach has been tested on multispectral images of a variety of natural land surfaces ranging from hyperarid deserts to tropical rain forests. Data were analyzed from Landsat MSS (multispectral scanner) and TM (Thematic Mapper), the airborne NS001 TM simulator, Viking Lander and Orbiter, AIS, and AVRIS (Airborne Visible and Infrared Imaging Spectrometer).

Adams, John B.↗
NASA NTRS1990

Quantitative lithologic mapping in spectral ratio feature space - Volcanic, sedimentary and metamorphic terrains

The nature of spectral lithologic mapping is studied utilizing ratios centered around the wavelength means of TM imagery. Laboratory-derived spectra are analyzed to determine the two-dimensional relationships and distributions visible in spectral ratio feature space. The spectral distributions of various rocks and minerals in ratio feature space are found to be controlled by several spectrally dominant molecules. Three study areas were examined: Rawhide Mining District, Nevada; Manzano Mountains, New Mexico; and the Sevilleta Long Term Ecological Research site in New Mexico. It is shown that, in the comparison of two ratio plots of laboratory reflectance spectra, i.e., 0.66/0.485 micron versus 1.65/2.22 microns with those derived from TM data, several molecules spectrally dominate the reflectance characteristic of surface lithologic units. Utilizing the above ratio combination, two areas are successfully mapped based on their distribution in spectral ratio feature space.

Campos-Marquetti, Raul, Jr.↗
NASA NTRS1991

Spectral properties of fog over the Malaspina Glacier, Alaska, in comparison to snow, ice, and clouds

Analysis of Landsat 5 Thematic Mapper (TM) data of the Malaspina Glacier in southeastern Alaska has shown that fog overlying the glacier ice has reflectance characteristics similar to the ice below and that the spectral reflectance of fog can be different from other types of clouds. Fog is more reflective in the visible and near-infrared wavelengths compared to snow, ice, and cumulus clouds. The differentiation between clouds, fog, and the ice below can be enhanced by combining TM bands in the visible part of the spectrum.

Ormsby, James P.↗
NASA NTRS1991

Response of vegetation indices to changes in three measures of leaf water stress

The responses of vegetation indices to changes in water stress were evaluated in two separate laboratory experiments. In one experiment the normalized difference vegetation index (NDVI), the near-IR to red ratio (near-IR/red), the Infrared Index (II), and the Moisture Stress Index (MSI) were more highly correlated to leaf water potential in lodgepole pine branches than were the Leaf Water Content Index (LWCI), the mid-IR ratio (Mid-IR), or any of the single Thematic Mapper (TM) bands. In the other experiment, these six indices and the TM Tasseled Cap brightness, greenness, and wetness indices responded to changes in leaf relative water content (RWC) differently than they responded to changes in leaf water content (WC) of three plant species, and the responses were dependent on how experimental replicates were pooled. With no pooling, the LWCI was the most highly correlated index to both RWC and WC among replications, followed by the II, MSI, and wetness. Only the LWCI was highly correlated to RWC and WC when replications were pooled within species. With among species pooling the LWCI was the only index highly correlated with RWC, while the II, MSI, Mid-IR, and wetness were most highly correlated with WC.

Cohen, Warren B.↗
NASA NTRS1991

Grain boundary sliding behaviour of copper and alpha brass at intermediate temperatures

The role of grain boundary sliding in copper and Cu-30 pct Zn in the temperature range 0.50-0.72 Tm, where Tm is the absolute melting point of the material, is examined. First, sliding data obtained on these materials are presented. The results indicate that the stress exponent for sliding is similar to that for lattice deformation, while the activation energy for sliding varies between 0.5 and 1.6 of the activation energy for creep. Several models proposed for grain boundary sliding are discussed, and it is shown that they do not account for the observed results on copper and alpha brass. A phenomenological model is proposed, where it is assumed that grain boundary sliding results from the glide of dislocations on secondary slip planes.

Raj, S. V.↗
NASA NTRS1991

Mojave remote sensing field experiment

The Mojave Remote Sensing Field Experiment (MFE), conducted in June 1988, involved acquisition of Thermal Infrared Multispectral Scanner (TIMS); C, L, and P-band polarimetric radar (AIRSAR) data; and simultaneous field observations at the Pisgah and Cima volcanic fields, and Lavic and Silver Lake Playas, Mojave Desert, California. A LANDSAT Thematic Mapper (TM) scene is also included in the MFE archive. TM-based reflectance and TIMS-based emissivity surface spectra were extracted for selected surfaces. Radiative transfer procedures were used to model the atmosphere and surface simultaneously, with the constraint that the spectra must be consistent with field-based spectral observations. AIRSAR data were calibrated to backscatter cross sections using corner reflectors deployed at target sites. Analyses of MFE data focus on extraction of reflectance, emissivity, and cross section for lava flows of various ages and degradation states. Results have relevance for the evolution of volcanic plains on Venus and Mars.

Arvidson, Raymond E.↗
NASA NTRS1992

Effects of long term exposure on optical substrates and coatings (SOO50-2)

Kodak included 12 substrate and coating samples on the Long Duration Exposure Facility (LDEF) structure. There were 3 fused silica and 3 ultra low expansion (ULE(tm)) uncoated glass samples, 2 ULE(tm) samples with a high reflectance silver coating, 2 fused silica samples with an antireflectance coating, and 2 fused silica samples with a solar rejection coating. The sample dimensions were 32 mm diameter by 1 mm thick. A set of duplicate control samples was also manufactured and stored in a controlled environment for comparison purposes. A preliminary evaluation of the flight samples for effects from the 5 year mission showed that a contaminant was deposited on the samples, a micrometeroid impact occurred on one of the samples, and the radiation darkening which was expected for the glass did not occur. The results are presented in more detail.

John Vallimont↗
NASA NTRS1992

Effects of long term space environment exposure on optical substrates and coatings (S0050-2)

The experiment consisted of Fused Silica and Ultra Low Expansion (ULE(tm)) glass samples which were either uncoated or had high reflectance silver, antireflectance, or solar rejection coatings. A set of duplicate control samples was manufactured and stored in a controlled environment for comparison purposes. We will present spectral curves for the glass and coatings which define preflight, postflight, and post-cleaning performance. Data on the analysis of the contaminate deposited on the samples and stress measurements in the glass will also be presented. Some results of particular interest are that the contaminate composition varied between different types of samples, and no darkening of the ULE(tm) glass occurred due to the radiation exposure.

Vallimont, John↗
NASA NTRS1992

Theoretical simulation of a 2 micron airborne solid state laser anemometer

In the near future, military aircraft will need to know precisely their true airspeed in order to optimize flight conditions. In comparison with classical anemometer probes, an airborne Doppler lidar allows measurement of the air velocity without influence from aircraft aerodynamic disturbance. While several demonstration systems of heterodyne detection using a CO2 laser have been reported, improvements in the technology of solid state lasers have recently opened up the possibility that these devices can be used as an alternative to CO2 laser systems. In particular, a diode pumped Tm:Ho:YAG laser allows a reliable compact airborne system with an eye safe wavelength (lambda = 2.09 microns) to be achieved. The theoretical study of performances of a coherent lidar using a solid state diode pumped Tm:Ho:YAG laser, caled SALSA, for measuring aircraft airspeed relative to atmospheric aerosols is described. A computer simulation was developed in order to modelize the Doppler anemometer in the function of atmospheric propagation and optical design. A clever analysis of the power budget on the detector area allows optical characteristic parameters of the system to be calculated, and then it can be used to predict performances of the Doppler system. Estimating signal to noise ratios (SNR) and heterodyne efficiency provides the available energy of speed measurement as well as a useful measurement of the alignment of the backscattered and reference fields on the detector.

Imbert, Beatrice↗
NASA NTRS1992

A study of atmospheric optical scattering parameters at 1.5 and 2 micron region for solid state Doppler lidar applications

The increasing interest in the development of an eye-safe, solid state, Doppler lidar for avionic applications has created the need for a quantitative evaluation of atmospheric effects on performance. Theoretical calculations were completed for optical scattering parameters to be compared with the field measurements. Computer codes were developed for the required calculations and designed to be interactive and user friendly in order to support comparison with experimental results and, thus, provide the basis for evaluation of eye-safe Doppler lidar over a wide range of atmospheric conditions and geographical locations. A holmium Doppler lidar operating at 2.09 microns was constructed for atmospheric backscattering, attenuation, and wind velocity measurements. Theoretical calculations and field studies were performed for backscatter coefficients. The selected wavelengths correspond to Er:glass, Tm:YAG, and Tm,Ho:YAG solid state lasers that are suitable for use in an eye-safe Doppler lidar system.

Margalit, Eli↗