Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Testing Cooperation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1948

Measurements in Flight of the Longitudinal-Stability Characteristics of a Republic YF-84A Airplane (Army Serial No. 45-59488) at High Subsonic Mach Numbers

A brief investigation was made of the longitudinal-stability characteristics of a YF-84A airplane (Army Serial No. 45-79488). The airplane developed a pitching-up tendency at approximately 0.80 Mach number which necessitated large push forces and down-elevator deflections for further increases in speed. In steady turns at 35,000 feet with the center of gravity at 28.3 percent mean aerodynamic chord for normal accelerations up to the maximum test value, the control-force gradients were excessive at Mach numbers over 0.78. Airplane buffeting did not present a serious problem in accelerated or unaccelerated flight at 15,000 and 35,000 feet up to the maximum test Mach number of 0.84. It is believed that excessive control force would be the limiting factor in attaining speeds in excess of 0.84 Mach number, especially at altitudes below 35,000 feet.

Turner, Howard L.↗
NASA NTRS2004

Isolated post resonator mesogyroscope

A new symmetric vibratory gyroscope principle has been devised in which a central post proof mass is counter-rocked against an outer sensing plate such that the motion is isolated from the gyroscope case. Prototype gyroscopes have been designed and fabricated with micromachined silicon at mesoscale (20-cm resonator width), vs. microscale (e.g., 2-mm resonator width) to achieve higher sensitivity and machined precision. This novel mesogyro design arose out of an ongoing technical cooperation between JPL and Boeing begun in 1997 to advance the design of micro-inertial sensors for low-cost space applications. This paper describes the theory of operation of the mesogyro and relationships with other vibratory gyroscopes, the mechanical design, closed loop electronics design, bulk silicon fabrication and packaged gyroscope assembly and test methods. The initial packaged prototype test results are reported for what is believed to be the first silicon mesogyroscope.

mesogyroscope↗
NASA NTRS2008

Microgravity, Mesh-Crawling Legged Robots

The design, fabrication, and microgravity flight-testing are part of a continuing development of palm-sized mobile robots that resemble spiders (except that they have six legs apiece, whereas a spider has eight legs). Denoted SpiderBots (see figure), they are prototypes of proposed product line of relatively inexpensive walking robots that could be deployed in large numbers to function cooperatively in construction, repair, exploration, search, and rescue activities in connection with exploration of outer space and remote planets.

Behar, Alberto↗
NASA NTRS2007

An Infrared Solution to a National Priority NASA Ice Detection and Measurement Problem

NASA has a serious problem with ice that forms on the cryogenic-filled Space Shuttle External Tank (ET) that could endanger the crew and vehicle. This problem has defied resolution in the past. To find a solution, a cooperative agreement was developed between NASA-Kennedy Space Center (KSC) and the U.S. Army-Tank-Automotive, armaments Research, Development & Engineering Center (TARDEC). This paper describes the need, initial investigation, solution methodology, and some results for a mobile near-IR ice detection and measurement system developed by MDA of Canada and jointly tested by the U.S. Army TARDEC and NASA. Performance results achieved demonstrate that the pre-launch inspection system has the potential to become a critical tool in addressing NASA's ice problem.

Meitzler, Thomas↗
DOE OSTI2022

Effect of fuel composition and EGR on spark-ignited engine combustion with LPG fueling: Experimental and numerical investigation

This paper presents an experimental and numerical investigation of a spark-ignited (SI) cooperative fuel research (CFR) engine fueled with different liquefied petroleum gas (LPG) fuels and exhaust gas recirculation (EGR). Here, the effects of LPG fuel composition on engine combustion characteristics are initially evaluated at two different compression ratios (CR). Results show normal combustion at CR 7 and heavy knocking combustion at CR 10 for all the tested fuels, with a more substantial impact for the LPG fuel with high proportions of n-butane species. The Livengood-Wu (LW) integral method is then used to analyze the knock occurrence risk of individual fuel based on the reactivity of the tested fuels. The introduction of EGR then demonstrates the potential of knock intensity reduction below the borderline knock limit. A zonal-based kinetic interactions study is also performed to understand the knock mitigation effectiveness of EGR over the pressure–temperature domain relevant to SI engine operation. Finally, a multidimensional, computational fluid dynamics (CFD) simulation model is shown to predict the LPG combustion characteristics and presents the evolution of in-cylinder temperature and chemical species to demonstrate the development of end-gas autoignition events without and with EGR.

02 PETROLEUM↗
NASA NTRS1970

Background and current status of the lifting body program

The lifting body concept was originally conceived by the Ames Research Center, and the design was developed over a period of years, from 1957 to 1964. By using a cone as a basic entry shape and modifying it to obtain lift and control, the M-2 shape evolved. In a cooperative venture with the NASA Ames Research Center to determine if a pilot could maneuver, flare, and land this class of vehicle, the Flight Research Center constructed a lightweight version of the lifting body, the M2-F1 vehicle. This vehicle was constructed during the fall of 1962 and spring of 1963 and extensively flight tested during the summer of 1963. Because of the success of the M2-F1 flight program, the research program was extended to include vehicles that would be representative of mission weight and wing loading. Figure 1 shows the three vehicles in the present lifting body program. On the left is the X-24A vehicle, which evolved from the U. S. Air Force's SV-5 PRIME vehicle; in the center is the M2-F3 vehicle, which is a modified version of the M2-F2 vehicle; and on the right is the HL-10 vehicle, which evolved from work at the NASA Langley Research Center.

John G McTigue↗
NASA NTRS1981

The LANDSAT system operated in Brazil by CNPq/INPE - results obtained in the area of mapping and future perspectives

The LANDSAT system, operated in the country by CNPg/INPE since 1973, systematically acquires, produces, and distributes both multispectral and panchromatic images obtained through remote sensing satellites to thousands of researchers and technicians involved in the natural resources survey. To cooperate in the solution of national problems, CNPq/INPE is developing efforts in the area of manipulation of those images with the objective of making them useful as planimetric bases for the simple revision of already published maps or for its utilization as basic material in regions not yet reliability mapped. The results obtained from performed tests are presented and the existing limitations are discussed. The new system purchased to handle data from the next series of LANDSAT as well as from MAPSAT and SPOT which will be in operation within the 80's decade, and are designed not only for natural resources survey but also for the solution of cartographic problems.

Dejesusparada, N.↗
NASA NTRS1985

Overview of free-piston Stirling technology at the NASA Lewis Research Center

An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center (Lewis) free-piston Stirling engine activities is presented. These activities include: (1) a generic free-piston Stirling technology project being conducted to develop technologies synergistic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort with the Department of Energy (DOE/Oak Ridge National Laboratory (ONRL)), and (2) a free-piston Stirling space-power technology demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), DOE, and NASA/Lewis. The generic technology effort includes extensive parametric testing of a 1 kw free-piston Stirling engine (RE-1000), development and validation of a free-piston Stirling performance computer code, and fabrication and initial testing of an hydraulic output modification for the RE-1000 engine. The space power technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including early test results.

Slaby, J. G.↗
NASA NTRS2005

Silicon Carbide Growth

Andrew Trunek has focused on supporting the Sic team through the growth of Sic crystals, making observations and conducting research that meets the collective needs and requirements of the team while fulfilling program commitments. Cancellation of the Ultra Efficient Engine Technology (UEET) program has had a significant negative impact on resources and research goals. This report highlights advancements and achievements made with this cooperative agreement over the past year. NASA Glenn Research Center (GRC) continues to make advances in silicon carbide (SiC) research during the past year. Step free surfaces were used as substrates for the deposition of GaN epilayers that yielded very low dislocation densities. Defect free 3C- SiC was successfully nucleated on step free mesas and test diodes were fabricated. Web growth techniques were used to increase the usable surface area of dislocation free SiC by approximately equal to 40%. The greatest advancement has been attained on stepped surfaces of SiC. A metrology standard was developed using high temperature etching techniques titled "Nanometer Step Height Standard". This development culminated in being recognized for a 2004 R&D100 award and the process to produce the steps received a NASA Space Act award.

Source record↗
DOE OSTI2023

Hidden depths in the local Universe: The Stellar Stream Legacy Survey

Context. Mergers and tidal interactions between massive galaxies and their dwarf satellites are a fundamental prediction of the Lambda-cold dark matter cosmology. These events are thought to provide important observational diagnostics of non-linear structure formation. Stellar streams in the Milky Way and Andromeda are spectacular evidence for ongoing satellite disruption. However, constructing a statistically meaningful sample of tidal streams beyond the Local Group has proven a daunting observational challenge, and the full potential for deepening our understanding of galaxy assembly using stellar streams has yet to be realised. Aims. Here we introduce the Stellar Stream Legacy Survey, a systematic imaging survey of tidal features associated with dwarf galaxy accretion around a sample of ~3100 nearby galaxies within z~0.02, including about 940 Milky Way analogues. Methods. Our survey exploits public deep imaging data from the DESI Legacy Imaging Surveys, which reach surface brightness as faint as ~29 mag arcsec –2 in the r band. As a proof of concept of our survey, we report the detection and broad-band photometry of 24 new stellar streams in the local Universe. Results. We discuss how these observations can yield new constraints on galaxy formation theory through comparison to mock observations from cosmological galaxy simulations. These tests will probe the present-day mass assembly rate of galaxies, the stellar populations and orbits of satellites, the growth of stellar halos, and the resilience of stellar disks to satellite bombardment.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1972

Temperature and velocity field of the two-dimensional transverse hot-air jet in a freestream flow.

Experimental investigation of the low subsonic, two-dimensional transverse hot-air jet. In the study jet-to-freestream angles of 90, 120, 135, and 150 deg and jet-to-freestream velocity ratios of 5, 10, and 20 were investigated. In the tests the jet velocity and temperature fields were measured using a temperature-compensated hot-wire anemometer. Photographs of the flowfield were also made. The tests results are compared with the available data and analysis. Results indicate a relatively minor deflection of the freestream by the jet and the presence of a large separated flow region behind the jet.

Tatom, J. W.↗
NASA NTRS2015

3D Printing in Zero-G Experiment, In Space Manufacturing (LPS, 4)

The 3D Printing in Zero‐G Experiment has been an ongoing effort for several years. In June 2014 the technology demonstration 3D printer was launched to the International Space Station. In November 2014 the first 21 parts were manufactured in orbit marking the beginning of a paradigm shift that will allow astronauts to be more self‐sufficient and pave the way to larger scale orbital manufacturing. Prior to launch the 21 parts were built on the ground with the flight unit with the same feedstock. These ground control samples are to be tested alongside the flight samples in order to determine if there is a measurable difference between parts built on the ground vs. parts built in space. As of this writing, testing has not yet commenced. Tests to be performed are structured light scanning for volume and geometric discrepancies, CT scanning for density measurement, destructive testing of mechanical samples, and SEM analysis for inter‐laminar adhesion discrepancies. Additionally, an ABS material characterization was performed on mechanical samples built from the same CAD files as the flight and ground samples on different machine / feedstock combinations. The purpose of this testing was twofold: first to obtain mechanical data in order to have a baseline comparison for the flight and ground samples and second to ascertain if there is a measurable difference between machines and feedstock.

Bean, Quincy↗
DOE OSTI2025

Tunable and Robust Optical and Structural Properties of a Cooperative Squaraine-Dye Aggregate-DNA DX-DAE Tile System

Molecular excitons, which are excitations delocalized over multiple dyes in a wavelike manner, are of interest for a wide range of applications, including quantum information science. Numerous studies have templated a variety of synthetic dyes via a DNA scaffold to induce dye aggregation to create molecular excitons upon photoexcitation. Dye aggregate optical properties are critically dependent on relative dye geometry and local environment; therefore, an understanding of dye-dye and DNA-dye interactions is critical for advancing toward more complex DNA-dye systems. The extensively studied DNA Holliday junction (HJ) and less-studied double-crossover (DX) tile motif are fundamental test beds for designing complex and ultimately modular DNA-dye architectures. Here, we report the first study of single-linked squaraine dye aggregation and exciton delocalization on a larger and more stable (compared with the HJ) DX tile motif. We first highlight a few DNA-dye constructs that support single dyes and aggregates with distinct optical properties that are both tunable—through sample design, buffer conditions, and heat treatment—and robust to environment changes, including transfer to solid phase. Next, we assess several experimental and design considerations that demonstrate directed dye-driven assembly of a novel double-tile DNA configuration. Our results demonstrate that single-linked squaraine dyes templated to DX tiles provide a viable research path to design and evaluate dye aggregate networks that support exciton delocalization. We include herein the first report of exciton delocalization in the solid phase in a DNA-dye construct. Additionally, our findings indicate that dye aggregation impacts the assembly of the DNA-dye construct, and, in some cases, thereby cooperates with the DNA to determine a final robust system configuration. Finally, we show that a controlled annealing schedule can be employed to promote the homogeneous assembly of DNA-dye constructs. The findings in this study contribute to the understanding of DNA-dye systems and the relevant factors involved in their directed assembly to achieve specific constructs with desirable properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Scalable Electrolytic Systems for Renewable Hydrogen Production (Cooperative Research and Development Final Report, CRADA Number CRD-18-747)

The project focuses on offshore wind energy which is an emergent renewable energy source in the United States. Onsite hydrogen production for this sector is not available. The overall goal of GTA's work is development of scalable multi-megawatt water electrolysis systems that exclude platinum group metals, are constructed from readily available commodity materials and are mass produced using advanced manufacturing and robotics. They fabricated and successfully tested a scalable TRL 4 laboratory prototype that demonstrated promising results for achieving the goal. They further performed calculations and prepared scale drawings for an envisioned onsite TRL 8 electrolytic hydrogen production system at an offshore 8 MW wind turbine. The work plan of the CRADA proposal between NREL and GTA focuses on validation of the current TRL 4 prototype with potential development and refinement for advancement to a TRL 5 system. GTA, Inc. proposes joining the H2@Scale consortium to leverage DOE funds, benefit from and contribute to the common knowledge-base and work with NREL as a CRADA partner.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1998

Autonomous Mobile Platform for Research in Cooperative Robotics

This paper describes the design and development of a platform for research in cooperative mobile robotics. The structure and mechanics of the vehicles are based on R/C cars. The vehicle is rendered mobile by a DC motor and servo motor. The perception of the robot's environment is achieved using IR sensors and a central vision system. A laptop computer processes images from a CCD camera located above the testing area to determine the position of objects in sight. This information is sent to each robot via RF modem. Each robot is operated by a Motorola 68HC11E micro-controller, and all actions of the robots are realized through the connections of IR sensors, modem, and motors. The intelligent behavior of each robot is based on a hierarchical fuzzy-rule based approach.

Daemi, Ali↗
NASA NTRS2001

Feasibility of Actively Cooled Silicon Nitride Airfoil for Turbine Applications Demonstrated

Nickel-base superalloys currently limit gas turbine engine performance. Active cooling has extended the temperature range of service of nickel-base superalloys in current gas turbine engines, but the margin for further improvement appears modest. Therefore, significant advancements in materials technology are needed to raise turbine inlet temperatures above 2400 F to increase engine specific thrust and operating efficiency. Because of their low density and high-temperature strength and thermal conductivity, in situ toughened silicon nitride ceramics have received a great deal of attention for cooled structures. However, the high processing costs and low impact resistance of silicon nitride ceramics have proven to be major obstacles for widespread applications. Advanced rapid prototyping technology in combination with conventional gel casting and sintering can reduce high processing costs and may offer an affordable manufacturing approach. Researchers at the NASA Glenn Research Center, in cooperation with a local university and an aerospace company, are developing actively cooled and functionally graded ceramic structures. The objective of this program is to develop cost-effective manufacturing technology and experimental and analytical capabilities for environmentally stable, aerodynamically efficient, foreign-object-damage-resistant, in situ toughened silicon nitride turbine nozzle vanes, and to test these vanes under simulated engine conditions. Starting with computer aided design (CAD) files of an airfoil and a flat plate with internal cooling passages, the permanent and removable mold components for gel casting ceramic slips were made by stereolithography and Sanders machines, respectively. The gel-cast part was dried and sintered to final shape. Several in situ toughened silicon nitride generic airfoils with internal cooling passages have been fabricated. The uncoated and thermal barrier coated airfoils and flat plates were burner rig tested for 30 min without and with air cooling. Without cooling, the surface temperature of the flat plate reached approximately 2350 F. Starting with computer aided design (CAD) files of an airfoil and a flat plate with internal cooling passages, the permanent and removable mold components for gel casting ceramic slips were made by stereolithography and Sanders machines, respectively. The gel-cast part was dried and sintered to final shape. Several in situ toughened silicon nitride generic airfoils with internal cooling passages have been fabricated. The uncoated and thermal barrier coated airfoils and flat plates were burner rig tested for 30 min without and with air cooling. Without cooling, the surface temperature of the flat plate reached approximately 2350 F. With cooling, the surface temperature decreased to approximately 1910 F--a drop of approximately 440 F. This preliminary study demonstrates that a near-net-shape silicon nitride airfoil can be fabricated and that silicon nitride can sustain severe thermal shock and the thermal gradients induced by cooling and, thus, is a viable candidate for cooled components.

Bhatt, Ramakrishna T.↗
NASA NTRS1980

Predicting lifetime of cast parts

Life expectancy of cast aluminum machine parts can be predicted accurately from fatigue tests at 78 K on notched specimens of aluminum alloy. Method was developed for rocket engine turbopump parts made of high strength, heat treatable alloy with high silicon content; however, technique is applicable to other aluminum casting alloys.

Cooper, R. A.↗