Wave Tank Testing of 1-DoF Heaving Buoy for Controls Validation Purposes
This submission includes the wave tank testing data used to validate the controls optimization efforts of a heaving 1-DoF buoy.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This submission includes the wave tank testing data used to validate the controls optimization efforts of a heaving 1-DoF buoy.
This study experimentally and computationally investigates the heat transfer capability of supercritical carbon dioxide (sCO 2 ) single jet impingement. The evaluated jet Reynolds number range is between 80,000 and 600,000, with a nondimensional jet-to-target surface spacing of 2.8. CO 2 -impinging jet stagnation conditions were maintained at approximately 200 bar and a temperature of ∼400 °C for most experiments. The goal is to understand how changes in the aforementioned parameters influence heat transfer between the working fluid and the heated surface. Additionally, due to the elevated Reynolds numbers and difference in thermodynamic properties between air and CO 2 , air-derived impingement correlations may not be appropriate for CO 2 impingement; these correlations will be evaluated against experimental sCO 2 impingement data. At the time of this study, no sCO 2 impingement data was available relevant to sCO 2 power cycles. The target surface is a 1.5-in. diameter copper block centered on the 3 mm jet orifice. A mica heating element bolted to the bottom of the copper block provides a uniform heat flux. Thermocouples embedded in the copper block are used to determine the surface temperature. Nusselt numbers obtained from experimental sCO 2 test data are compared to area-averaged Nusselt numbers from air-derived correlations. The comparisons showed that air correlations drastically underpredict the heat transfer when sCO 2 is used as the working fluid. A modified sCO 2 correlation using experimental data at discussed conditions is derived based on an existing air correlation. A CFD study is also performed to further investigate sCO 2 heat transfer characteristics, and assess the numerical model applicability to this problem type.
The purpose of this CRADA was to develop, integrate, and test design changes to LLNL’s field prototype autonomous pathogen detection system (APDS). The desired result of this project was an improved design of the APDS, along with test data characterizing performance of the new hardware, software, and processes. This improved design was to be closer to the final production design for operation. The third amendment to the Statement of Work (SOW) significantly redefined the scope of the work from general improvements to creating a NGSS built system that included the improvements from before and prepared the system for head to head testing for the BioWatch Gen-3 program. All deliverables were met on time and on budget.
This memorandum documents laboratory thermomechanical triaxial strength testing of Waste Isolation Pilot Plant (WIPP) clean salt. The limited study completed independent, adjunct laboratory tests in the United States to assist in validating similar testing results being provided by the German facilities. The testing protocol consisted of completing confined triaxial, constant strain rate strength tests of intact WIPP clean salt at temperatures of 25°C and 100°C and at multiple confining pressures. The stratigraphy at WIPP also includes salt that has been labeled “argillaceous.” The much larger test matrix conducted in Germany included both the so-called clean and argillaceous salts. When combined, the total database of laboratory results will be used to develop input parameters for models, assess adequacy of existing models, and predict material behavior. These laboratory studies are also consistent with the goals of the international salt repository research program. The goal of this study was to complete a subset of a test matrix on clean salt from the WIPP undertaken by German research groups. The work was performed at RESPEC in Rapid City, South Dakota. A rigorous Quality Assurance protocol was applied, such that corroboration provides the potential of qualifying all of the test data gathered by German research groups.
The purpose of this CRADA was to develop, integrate, and test design changes to LLNL’s field prototype autonomous pathogen detection system (APDS). The desired result of this project was an improved design of the APDS, along with test data characterizing performance of the new hardware, software, and processes. This improved design was to be closer to the final production design for operation. The third amendment to the Statement of Work (SOW) significantly redefined the scope of the work from general improvements to creating a NGSS built system that included the improvements from before and prepared the system for head to head testing for the BioWatch Gen-3 program. All deliverables were met on time and on budget.
This study implements a data-intensive supervised ML approach through a quasi-experimental framework with the objective of quantifying the impact of oil and gas operator-specific proprietary data on ML-based predictive model performance relative to using oil and gas datasets that may be more commonly publicly available. The models are designed to jointly predict daily oil, gas, and water production for horizontal wells as a function of bottom-hole pressure drawdown, spatial placement across the study domain, and well completion attributes. Model performance is quantified on holdout test data to evaluate how each dataset affects resulting model variant performance.
The primary objective of this study is to validate the system analysis code, SAM, using experimental data from the Compact Integral Effects Test (CIET) facility. The System Analysis Module (SAM) is an advanced and modern system analysis tool being developed at Argonne National Laboratory under the U.S. DOE Office of Nuclear Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. Originally aiming at supporting sodium fast reactor (SFR) design, it is now extended to cover other non-light water reactor (non-LWR) concepts, such as high-temperature gas-cooled reactor (HTGR) designs, molten salt-fueled, and molten salt-cooled reactor designs. To support SAM code development for the wide range of non-LWR applications, it is of paramount importance to validate the code against experiments relevant to these reactor concepts. The Compact Integral Effects Test (CIET) facility, which was designed to reproduce the thermal-hydraulics response of fluoride salt-cooled high-temperature reactors (FHR) under both forced- and natural-circulation conditions, has been identified and selected as one of benchmark test facilities for SAM code validation. Among available CIET experiments, three sets of them with distinctive characteristics were selected for SAM code validation purpose. The three sets experiments are: 1) Power step change transient tests; 2) DHX-DRACS natural circulation tests; and 3) heater frequency response tests. For all tests, steady-state or transient, SAM-predicted results show very good agreement with experimental data. The successful validation of SAM against these selected CIET experiments demonstrates that the computer code is well suited for thermal-hydraulics analysis of FHR designs.
To make concentrating solar power (CSP) more cost competitive, rigourous optimizations must be run to improve plant design and operations. However, these optimizaitons rely on time consuming annual simulations that solve an electricity dispatch scheduling problem to maximize plant revenue. To reduce the runtime of annual dispatch simulations of CSP plants, a data clustering approach is utilized. This approach assumes that like days of revenue and electricity generation can be identified using weather and price data. Although weather and price are important factors for electricity production, this work investigates how thermal energy storage (TES) inventory at the beginning of a day, denoted as Si, can be used as a supplemental feature to group like days. A framework for creating and training a deep neural network to predict Si is proposed. This model is validated and assessed using eleven sets of testing data that were not used during training. Then, the data clustering approach is performed three seperate times with features of weather and price along with either Si from the neural network, Si from the full annual simulation, or no Si. Ultimately, the results suggest that using Si as an additional clustering feature improves the data clustering simulation accuracy by 1.4%.
Cellular solids such as elastomeric foams are used in many structural applications to absorb and dissipate energy, due to their light weight (low density) and high energy absorption capability. In this paper we will discuss foams derived from S5370, a silicone foam formulation developed by Dow Corning. In the application presented, the foam is consolidated into a cushion component of constant thickness but variable density. A mechanical material model developed by Lewis (2013), predicts material response, in part, as a function of relative density. To determine the required parameters for this model we have obtained the mechanical response in compression for ambient, cold and hot temperatures. The variable density cushion provided samples sufficient samples so that the effect of sample initial density on the mechanical response could be studied. The mechanical response data showed extreme sensitivity to relative density. We also observed at strains corresponding to 1 MPa a linear relationship between strain and initial density for all temperatures. Samples taken from parts with a history of thermal cycling demonstrated a stiffening response that was a function of temperature, with the trend of more stiffness as temperature increased above ambient. This observation is in agreement with the entropic effects on the thermo-mechanical behavior of silicone polymers. In this study, we present the experimental methods necessary for the development of a material model, the testing protocol, analysis of test data, and a discussion of load (stress) and gap (strain) as a function of sample initial densities and temperatures
Sustainable feedstock harvest strategies are needed to ensure bioenergy production does not irreversibly degrade soil resources. The objective for this study was to document corn (Zea mays L.) grain and stover fraction yields, plant nutrient removal and replacement costs, feedstock quality, soil-test changes, and soil quality indicator response to four stover harvest strategies for continuous corn and a corn-soybean [Glycine max. (L.) Merr.] rotation. The treatments included collecting (1) all standing plant material above a stubble height of 10 cm (whole plant), (2) the upper-half by height (ear shank upward), (3) the lower-half by height (from the 10 cm stubble height to just below the earshank), or (4) no removal. Collectable biomass from Treatment 2 averaged 3.9 ({+-}0.8) Mg ha{sup -1} for continuous corn (2005 through 2009), and 4.8 ({+-}0.4) Mg ha{sup -1} for the rotated corn (2005, 2007, and 2009). Compared to harvesting only the grain, collecting stover increased the average N-P-K removal by 29, 3 and 34 kg ha{sup -1} for continuous corn and 42, 3, and 34 kg ha{sup -1} for rotated corn, respectively. Harvesting the lower-half of the corn plant (Treatment 3) required two passes, resulted in frequent plugging of the combine, and provided a feedstock with low quality for conversion to biofuel. Therefore, Treatment 3 was replaced by a 'cobs-only' harvest starting in 2009. Structural sugars glucan and xylan accounted for up to 60% of the chemical composition, while galactan, arabinan, and mannose constituted less than 5% of the harvest fractions collected from 2005 through 2008. Soil-test data from samples collected after the first harvest (2005) revealed low to very low plant-available P and K levels which reduced soybean yield in 2006 after harvesting the whole-plant in 2005. Average continuous corn yields were 21% lower than rotated yields with no significant differences due to stover harvest. Rotated corn yields in 2009 showed some significant differences, presumably because soil-test P was again in the low range. A soil quality analysis using the Soil Management Assessment Framework (SMAF) with six indicators showed that soils at the continuous corn and rotated sites were functioning at an average of 93 and 83% of their inherent potential, respectively. With good crop management practices, including routine soil-testing, adequate fertilization, maintenance of soil organic matter, sustained soil structure, and prevention of wind, water or tillage erosion, a portion of the corn stover being produced in central Iowa, USA can be harvested in a sustainable manner.
The LSST Camera focal plane will be constructed with 21 144-Mpixel modules (\Raft Tower Module", RTM). An extensive operational test is performed to confirm the integrity of all connections and to verify the basic functionality. Each RTM undergoes at least four connectivity tests. A python script communicates with Java- based control software and performs the test. A python script parses the test data and generates a PDF report. The report includes a summary PASS/FAIL table, several hundred current, voltage and temperature parameters, and images taken with the CCD array at room temperature.
This report provides the mechanical test data of laser powder bed fusion (LPBF) 316H stainless steel (SS) collected during Fiscal Year 2024 (FY 24) under the US Department of Energy, Office of Nuclear Energy’s Advanced Materials and Manufacturing Technologies program, along with the current state of microstructural-based understandings of the behaviors. Materials with variabilities in manufacturing site, machine, laser parameters, powder chemistry, porosity, specimen geometry and heat treatment were tested in high-temperature tension, creep, fatigue and creep-fatigue. Electron microscopy and optical microscopy were performed on selected materials before and after the tests to provide microstructural-based understandings to the mechanical behavior. It was discovered that the as-built (AB) and stress-relieved (SR) materials exhibit similar behaviors in tension and creep, as do the solution-annealed (SA) and hot-isostatic pressed (HIP) materials. The AB and SR materials are softer but more ductile than the SA and HIP materials in tension. In creep, the LPBF materials have comparable rupture times but lower rupture strains compared to the wrought materials. The AB and SR materials have low creep rupture strains (<10%) when tested at 720°C and 800°C, while the SA and HIP materials are much more ductile. The LPBF materials exhibit large scatter in fatigue and creep-fatigue lives. The cyclic lives of creep-fatigue tests are lower than those of fatigue tests. In fatigue and creep-fatigue, SR materials outperform SA materials. A common observation from the cyclic tests is that, given the same post-build heat treatment, a lower initial peak stress generally results in a longer cyclic life regardless of hold time. It was also discovered that the batch variation can be more impactful than heat treatment, as demonstrated by the overall better performance of one batch of material than another, regardless of the heat treatment. The results provided insights into how different factors impact the behaviors of LPBF 316H SS. An outlook to FY 25 work scope is provided.
PBX 9502 is an important insensitive high explosive due to its combination of safety properties and detonation performance. It is a polymer-bonded formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the high explosive crystal, bound with Kel F-800 (FK-800), a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Two different types are used, one known as virgin that uses only pristine manufactured TATB, and a second known as recycled that has 50 wt.% of its TATB reclaimed from machining scraps of previously pressed virgin PBX 9502. Recycled lots have a higher percentage of fine particles compared to virgin lots, due to the fracturing and damage sustained by TATB crystals during pressing. We examine the influence that this TATB microstructure difference between virgin and recycled PBX 9502 has on detonation performance properties. New rate-stick geometry diameter effect, detonation front shape and cylinder expansion test data are obtained for two previously uncharacterized virgin lots and one recycled lot of PBX 9502. This is combined with previously published data for one virgin and one recycled lot for evaluation purposes. Detonation shock dynamics model calibrations are conducted on each of the five lots to provide an assessment of the detonation timing characteristics of virgin versus recycled PBX 9502 lots. For two of the virgin lots, detonations propagate slower in the rate-stick geometry than those in the two recycled lots. However, the other virgin lot tested has propagation rates comparable to that of the recycled lots for larger diameter rate-sticks. The latter result, though, is shown to be geometry dependent and depends on the range of detonation curvatures accessed in different geometries. New copper-confined, cylinder expansion tests are conducted on each of the three virgin and two recycled lots to obtain detonation product Jones-Wilkins-Lee equations of state, enabling an assessment of the metal push capabilities for each of the five lots. We find that the metal push capabilities, characterized by the evolution of the heat of detonation with volume, are similar between the virgin and recycled lots. Thus, changes in microstructure between different PBX 9502 lots seemingly affect the rate of reaction, but not the overall energy content.
A complete description of nucleon structure requires the simultaneous knowledge of both the spatial and momentum information of the ultimate constituents of the nucleon, the quarks and gluons. Generalized Parton Distributions (GPDs) provide such tools to describe nucleon structure. GPDs are measurable through hard exclusive processes like Deeply Virtual Compton Scattering (DVCS) and Deeply Virtual Meson Production (DVMP). GPDs can describe hard exclusive processes only if Bjorken factorization is achieved during the hard scattering process. While DVCS data have given hints of the factorization regime being attained, such hints have not been observed for DVMP data. Testing for factorization in DVMP processes is the topic of this thesis. Exclusive π 0 electroproduction has been measured by experiment E12-06-114 in Hall A of JLab. Cross sections have been measured at three fixed Bjorken- x ( x B ): 0.35, 0.48 and 0.6 in the Q 2 range 3 to 9 GeV 2 . In this document we present an analysis of a subset of the data: x B = 0.35 in the Q 2 range 3.1 to 4.5 GeV 2 . The different structure functions: unseparated cross section (σ T + ϵσ L ), longitudinal-transverse interference (σ LT ), transverse-transverse interference (σ TT ), and the polarized response (σ LT' ) terms were extracted. The data was compared to a transversity GPD model. The model fails to reproduce the data even though the order of magnitude is in agreement for both model and data. We observe a strong disagreement between the data and the model for σ LT in terms of both magnitude and the cross section sign. Our results are in a larger and wider Q 2 domain but they are in agreement with existing measurements.
The heterogeneity in the composition of municipal solid wastes (MSW) poses significant challenges in the production of biofuel and bioproducts. This research aims to enhance the accuracy and efficiency of waste analysis and characterization by introducing a fast characterization approach for MSW-derived refuse-derived fuels (RDF) by combining Laser-Induced Breakdown Spectroscopy (LIBS) with advanced machine learning (ML) techniques. The approach combines data pre-processing of LIBS spectra of RDF, and the development of ML models trained on domain and theory-based spectral features for predicting process parameters. These models are adept at predicting key process parameters like High Heating Value (HHV), carbon content, and volatile matter. This approach can achieve an average RRMSE of 2.13% and R 2 of 0.98 or higher for all considered parameters on testing data. This work demonstrates significant potential for improving waste sorting, processing efficiency, and environmental compliance over traditional labor- and time-intensive laboratory waste analysis and characterization.
Reliable and accurate estimation of an electric bus’s instantaneous energy consumption is critical in evaluating energy impacts of planning and control of electric bus operations. In this study, we developed machine learning-based long short-term memory (LSTM) and artificial neural network (ANN) models to estimate 1 Hz energy consumption of electric buses based on continuous monitoring data of electric buses in Chattanooga, Tennessee, in 2019 and 2020. We propose a data-partitioning algorithm to separate energy charging and discharging modes before applying data-driven estimation models. Here, a K-fold cross-validation-based model selection process was conducted to identify the optimal model structure and input variables in terms of prediction accuracy. The estimation results show the predicted mean absolute percentage error rates of LSTM and ANN models were 3% and 5%, respectively. We compared the proposed models with existing models in the literature based on the same testing data to demonstrate the predictability of our models.
Pulse jet mixing (PJM) tests with noncohesive solids in Newtonian liquid were conducted at three geometric scales to support the design of mixing systems for the Hanford Waste Treatment and Immobilization Plant. The test data will be used to develop mixing models. The models predict the cloud height (the height to which solids will be lifted by the PJM action) and the critical suspension velocity (the minimum velocity needed to ensure all solids have been lifted from the floor. From the cloud height estimate, the concentration of solids near the vessel floor and the minimum velocity predicted to lift solids can be calculated. The test objective was to observe the influence of vertically downward-directed jets on noncohesive solids in a series of scaled tanks with several bottom shapes. The test tanks and bottom shapes included small-and large-scale tanks with elliptical bottoms, a mid-scale tank with a spherical bottom, and a large-scale tank with an F&D bottom. During testing, the downward-directed jets were operated in either a steady flow condition or a pulsed (periodic) flow condition. The mobilization of the solids resulting from the jets was evaluated based on: the motion/agitation of the particulate on the tank floor and the elevation the solids reach within the tank; the height the solids material reaches in the tank is referred to as the cloud height (HC).
In random vibration environments, sinusoidal line noise may appear in the vibration signal and can affect analysis of the resulting data. We studied two methods which remove stationary sine tones from random noise: a matrix inversion algorithm and a chirp-z transform algorithm. In addition, we developed new methods to determine the frequency of the tonal noise. The results show that both of the removal methods can eliminate sine tones in prefabricated random vibration data when the sine-to-random ratio is at least 0.25. For smaller ratios down to 0.02 only the matrix inversion technique can remove the tones, but the metrics to evaluate its effectiveness also degrade. We also found that using fast Fourier transforms best identified the tonal noise, and determined that band-pass-filtering the signals prior to the process improved sine removal. When applied to actual vibration test data, the methods were not as effective at removing harmonic tones, which we believe to be a result of mixed-phase sinusoidal noise.