Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scanning electron microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Direct measurement of electron channeling in a crystal using scanning transmission electron microscopy

Self-focusing of an atomic-scale high-energy electron wave packet by channeling along a zone axis in crystalline silicon is directly measured by scanning transmission electron microscopy using thin epitaxial SrTiO{sub 3}(100) islands grown on Si(100) as test objects. As the electron probe propagates down a silicon atom column, it is progressively focused onto the column, resulting in a fourfold increase in the scattered signal at the channeling maximum. This results in an enhancement of the visibility of the SrTiO{sub 3} islands, which is lost if the sample is flipped upside down and the channeling occurs only after the probe scatters off the SrTiO{sub 3} layer. The evolution of the probe wave function calculated by the multislice method accurately predicts the trends in the channeling signal on an absolute thickness scale. We find that while electron channeling enhances the visibility of on-column atoms, it suppresses the contribution from off-column atoms. It can therefore be used as a filter to selectively image the atoms that are most aligned with the atomic columns of the substrate. By using this technique, coherent islands can be distinguished from relaxed islands. For SrTiO{sub 3} films formed in a topotactic reaction on Si(100), we show that only {approx}55% of the SrTiO{sub 3} is aligned with the Si atom columns. The fraction of coherent SrTiO{sub 3} islands on Si(100) can be increased by choosing growth conditions away from equilibrium.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cathodoluminescence of stacking fault bound excitons for local probing of the exciton diffusion length in single GaN nanowires

We perform correlated studies of individual GaN nanowires in scanning electron microscopy combined to low temperature cathodoluminescence, microphotoluminescence, and scanning transmission electron microscopy. We show that some nanowires exhibit well localized regions emitting light at the energy of a stacking fault bound exciton (3.42 eV) and are able to observe the presence of a single stacking fault in these regions. Precise measurements of the cathodoluminescence signal in the vicinity of the stacking fault give access to the exciton diffusion length near this location.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Direct measurement of the thermal expansion coefficient of epitaxial WSe 2 by four-dimensional scanning transmission electron microscopy

Current reports of thermal expansion coefficients (TEC) of two-dimensional (2D) materials show large discrepancies that span orders of magnitude. Determining the TEC of any 2D material remains difficult due to approaches involving indirect measurement of samples that are atomically thin and optically transparent. We demonstrate a methodology to address this discrepancy and directly measure TEC of nominally monolayer epitaxial WSe 2 using four-dimensional scanning transmission electron microscopy (4D-STEM). Experimentally, WSe 2 from metal-organic chemical vapor deposition (MOCVD) was heated through a temperature range of 18- 564 °C using a barrel-style heating sample holder to observe temperature-induced structural changes without additional alterations or destruction of the sample. By combining 4D-STEM measurements with quantitative structural analysis, the thermal expansion coefficient of nominally monolayer polycrystalline epitaxial 2D WSe 2 was determined to be (3.5 ± 0.9) × 10 -6 K -1 and (5.7 ± 2) × 10 -5 K -1 for the in- and out-of-plane TEC, respectively, and (3.6 ± 0.2) × 10 -5 K -1 for the unit cell volume TEC, in good agreement with historically determined values for bulk crystals.

2D materials↗

Direct imaging of light elements by annular dark-field aberration-corrected scanning transmission electron microscopy

In this report, we show that an annular dark-field detector in an aberration-corrected scanning transmission electron microscope allows the direct observation of light element columns in crystalline lattices. At specific imaging conditions, an enhancement of the intensities of light element columns in the presence of heavy element columns is observed. Experimental results are presented for imaging the nitrogen and carbon atomic columns at the GaN-SiC interface and within the GaN and SiC compounds. The crystal polarity of GaN at the interface is identified. The obtained findings are discussed and are well supported by image simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructure of high-strength foam concrete

Foam concretes are divided into two groups: on the one hand the physically foamed concrete is mixed in fast rotating pug mill mixers by using foaming agents. This concrete cures under atmospheric conditions. On the other hand the autoclaved aerated concrete is chemically foamed by adding aluminium powder. Afterwards it is cured in a saturated steam atmosphere. New alternatives for the application of foam concretes arise from the combination of chemical foaming and air curing in manufacturing processes. These foam concretes are new and innovative building materials with interesting properties: low mass density and high strength. Responsible for these properties are the macro-, meso- and microporosity. Macropores are created by adding aluminium powder in different volumes and with different particle size distributions. However, the microstructure of the cement matrix is affected by meso- and micropores. In addition, the matrix of the hardened cement paste can be optimized by the specific use of chemical additives for concrete. The influence of aluminium powder and chemical additives on the properties of the microstructure of the hardened cement matrices were investigated by using petrographic microscopy as well as scanning electron microscopy.

36 MATERIALS SCIENCE↗

Solid Phase Characterization of Tank 241-AY-102 Annulus Space Particulate

The Special Analytical Studies Group at the 222-S Laboratory (222-S) examined the particulate recovered from a series of samples from the annular space of tank 241-AY-102 (AY-102) using solid phase characterization (SPC) methods. These include scanning electron microscopy (SEM) using the ASPEX® scanning electron microscope, X-ray diffraction (XRD) using the Rigaku® MiniFlex X-ray diffractometer, and polarized light microscopy (PLM) using the Nikon® Eclipse Pol optical microscope. The SEM is equipped with an energy dispersive X-ray spectrometer (EDS) to provide chemical information.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Molecular self-assembled designing and characterization of TiO2 NPs-CdS QDs-dye composite for photoanode materials

Highlights: • Initially TiO{sub 2} NPs were synthesized by sol-gel method and CdS QDs by one pot synthesis method. • The connectivity between TiO{sub 2} NPs and CdS QDs was well revealed by zeta potential and FTIR techniques. • This binary system was sensitized with N719 dye molecule for better photoanode material. • Ternary TiO{sub 2} NPs-CdS QDs-N719 dye photoanode showed higher conversion efficiency than its binary photoanode devices. - Abstract: Ternary based photoanodes have been prepared by using titanium dioxide (TiO{sub 2}) nanoparticles (NPs), cadmium sulfide (CdS) quantum dots (QDs) and N719 dye. Initially, CdS QDs and TiO{sub 2} NPs were synthesized by one pot synthesis and sol-gel method, respectively. CdS QDs were connected electrostatically to the surfaces of TiO{sub 2} NPs, and after that, this binary hybrid further self-assembled with N719 dye to form the composites. The NPs, QDs and the resultant composites are characterized by using different techniques. The connectivity of these anatase TiO{sub 2} NPs with cubic CdS QDs are confirmed by FTIR; while the broad coverage of these materials is studied through UV–Visible diffuse reflectance spectroscopy (DRS). The surface topology and the cross-sectional morphology of thin films are studied by high resolution transmission electron microscopy (HR-TEM) and field emission scanning electron microscopy (FE-SEM) techniques; while the structural properties of NPs and QDs are studied by X-ray diffractometer (XRD). The synergetic co-sensitization of CdS and N719 dye significantly enhancing the overall power conversion efficiency (η) of TiO{sub 2} up to 2.37% (J{sub sc} = 10.31 mA/cm{sup 2} and V{sub oc} of 550 mV) (100 mW/cm{sup 2}). The J{sub sc}, V{sub oc}, and η values along with Incident photon to current conversion efficiency (IPCE) value of ternary photoelectrode-based solar devices, is almost double to that of either binary TiO{sub 2} NPs-CdS QDs or binary TiO{sub 2} NPs-N719 binary systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Unexpected bismuth concentration profiles in metal-organic vapor phase epitaxy-grown Ga(As{sub 1−x}Bi{sub x})/GaAs superlattices revealed by Z-contrast scanning transmission electron microscopy imaging

A set of GaAs{sub 1−x}Bi{sub x}/GaAs multilayer quantum-well structures was deposited by metal-organic vapor phase epitaxy at 390 °C and 420 °C. The precursor fluxes were introduced with the intent of growing discrete and compositionally uniform GaAs{sub 1−x}Bi{sub x} well and GaAs barrier layers in the epitaxial films. High-resolution high-angle annular-dark-field (or “Z-contrast”) scanning transmission electron microscopy imaging revealed concentration profiles that were periodic in the growth direction, but far more complicated in shape than the intended square wave. The observed composition profiles could explain various reports of physical properties measurements that suggest compositional inhomogeneity in GaAs{sub 1−x}Bi{sub x} alloys as they currently are grown.

36 MATERIALS SCIENCE↗

Ultra-fast solid state electro-optical modulator based on liquid crystal polymer and liquid crystal composites

A different generation of polymer-dispersed liquid crystals (PDLCs) based on a liquid crystalline polymer host is reported wherein the fluid behavior of the reactive mesogenic monomer is an enabler to concentration windows (liquid crystal polymer/liquid crystal) (and subsequent morphologies) not previously explored. These liquid crystal (LC) polymer/LC composites, LCPDLCs, exhibit excellent optical and electro-optical properties with negligible scattering losses in both the ON and OFF states. These systems thus have application in systems where fast phase modulation of optical signal instead of amplitude control is needed. Polarized optical microscopy and high resolution scanning electron microscopy confirm a bicontinuous morphology composed of aligned LC polymer coexisting with a phase separated LC fluid. Operating voltages, switching times, and spectra of LCPDLCs compare favourably to conventional PDLC films. The LCPDLCs exhibit a low switching voltage (4–5 V/μm), symmetric and submillisecond (200 μs) on/off response times, and high transmission in both the as formed and switched state in a phase modulation geometry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Scale Spallation During Coiling on the Electrochemical and Pickling Behavior of a Hot-Rolled Dual-Phase Steel

Tertiary oxide scale consists of magnetite and hematite, and in dual-phase steel strips were observed after the exit of final rolling stand in a thin slab casting rolling (TSCR) mill. Microscopic observation confirmed that these scales cracked and spalled off from many places of surface during coiling causing a non-uniform oxide layer on the steel surface. The present work discusses the synergistic effect of such non-uniform oxide layer and run-out-table cooling water on the electrochemical behavior of the dual-phase steel. The electrochemical response was assessed with the help of dynamic and linear polarization tests considering cooling water as electrolyte. The presence of non-uniform scale produced high cathodic (scaled zone) to anodic (spalled-off zone) area ratio that eventually led to extensive pitting corrosion in the present steel. Furthermore, the pickling behavior of the steel was also studied in detail. It was observed that the steel surface, with spalled-off area of about one-tenth of total surface area, corroded preferentially 3-4 times faster at spalled-off area than that of the uniformly pickled surface. The characterization study was performed using scanning electron microscopy, confocal laser 3D scanning microscopy, x-ray diffraction and Raman spectroscopy in order to establish the reasons for pitting corrosion due to the scale spallation.

36 MATERIALS SCIENCE↗

TEM characterization of Au-based alloys to join YSZ to steel for SOFC applications

The microstructures of two gold-based alloys with compositions (in wt.%) of 96.4Au-3Ni-0.6Ti and 97.5Au-0.75Ni-1.75V following oxidation at 850 Degree-Sign C for 200 min were characterized by analytical transmission electron microscopy with energy dispersive spectroscopy and by scanning electron microscopy. In the oxidized 96.4Au-3Ni-0.6Ti interlayer, a dense scale composed of nickel oxide (NiO) and nickel titanate (NiTiO{sub 3}) formed at the alloy surface. No evidence of titanium oxide was found because there was not enough Ti present to form titanium oxide. In the oxidized 97.5Au-0.75Ni-1.75V interlayer, loose vanadium oxide (V{sub 2}O{sub 5}) and nickel vanadate (Ni{sub 2}V{sub 2}O{sub 7}) formed and were distributed within the oxidized 97.5Au-0.75Ni-1.75V interlayer. Similarly, because of the low Ni content in the alloys, no NiO formed. The oxide products in the 96.4Au-3Ni-0.6Ti and 97.5Au-0.75Ni-1.75V interlayers after oxidation are consistent with the Pilling-Bedworth (PB) ratio considerations. - Highlights: Black-Right-Pointing-Pointer Two commercial Au-based reactive metallic interlayers were oxidized at 850 Degree-Sign C for 200 min. Black-Right-Pointing-Pointer The oxidized products at the surface were characterized by TEM/EDS and SEM. Black-Right-Pointing-Pointer NiO and NiTiO{sub 3} formed at the oxidized 96.4Au-3Ni-0.6Ti interlayer. Black-Right-Pointing-Pointer V{sub 2}O{sub 5} and Ni{sub 2}V{sub 2}O{sub 7} were found in the oxidized 97.5Au-0.75Ni-1.75V interlayer. Black-Right-Pointing-Pointer These oxide products are consistent with the Pilling-Bedworth (PB) ratio considerations.

36 MATERIALS SCIENCE↗

Interpretable and Efficient Interferometric Contrast in Scanning Transmission Electron Microscopy with a Diffraction-Grating Beam Splitter

Efficient imaging of biomolecules, 2D materials and electromagnetic fields depends on retrieval of the phase of transmitted electrons. We demonstrate a method to measure phase in a scanning transmission electron microscope using a nanofabricated diffraction grating to produce multiple probe beams. The measured phase is more interpretable than phase-contrast scanning transmission electron microscopy techniques without an off-axis reference wave, and the resolution could surpass that of off-axis electron holography. Here, we apply the technique to image nanoparticles, carbon sub- strates and electric fields. The contrast observed in experiments agrees well with contrast predicted in simulations.

36 MATERIALS SCIENCE↗

Development of an in-situ multi-component reinforced Al-based metal matrix composite by direct metal laser sintering technique — Optimization of process parameters

In the present investigation, an in-situ multi-component reinforced aluminum based metal matrix composite was fabricated by the combination of self-propagating high-temperature synthesis and direct metal laser sintering process. The different mixtures of Al, TiO{sub 2} and B{sub 4}C powders were used to initiate and maintain the self-propagating high-temperature synthesis by laser during the sintering process. It was found from the X-ray diffraction analysis and scanning electron microscopy that the reinforcements like Al{sub 2}O{sub 3}, TiC, and TiB{sub 2} were formed in the composite. The scanning electron microscopy revealed the distribution of the reinforcement phases in the composite and phase identities. The variable parameters such as powder layer thickness, laser power, scanning speed, hatching distance and composition of the powder mixture were optimized for higher density, lower porosity and higher microhardness using Taguchi method. Experimental investigation shows that the density of the specimen mainly depends upon the hatching distance, composition and layer thickness. On the other hand, hatching distance, layer thickness and laser power are the significant parameters which influence the porosity. The composition, laser power and layer thickness are the key influencing parameters for microhardness. - Highlights: • The reinforcements such as Al{sub 2}O{sub 3}, TiC, and TiB{sub 2} were produced in Al-MMC through SHS. • The density is mainly influenced by the material composition and hatching distance. • Hatching distance is the major influencing parameter on porosity. • The material composition is the significant parameter to enhance the microhardness. • The SEM micrographs reveal the distribution of TiC, TiB{sub 2} and Al{sub 2}O{sub 3} in the composite.

36 MATERIALS SCIENCE↗

Holders for in situ treatments of scanning tunneling microscopy tips

We have developed holders for scanning tunneling microscopy tips that can be used for in situ treatments of the tips, such as electron bombardment (EB) heating, ion sputtering, and the coating of magnetic materials. The holders can be readily installed into the transfer paths and do not require any special type of base stages. Scanning electron microscopy is used to characterize the tip apex after EB heating. Also, spin-polarized scanning tunneling spectroscopy using an Fe coated W tip on the Cr(001) single crystal surface is performed in order to confirm both the capability of heating a tip up to about 2200 K and the spin sensitivity of the magnetically coated tip.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Scattering Matrix Determination in Crystalline Materials from 4D Scanning Transmission Electron Microscopy at a Single Defocus Value

Recent work has revived interest in the scattering matrix formulation of electron scattering in transmission electron microscopy as a stepping stone toward atomic-resolution structure determination in the presence of multiple scattering. Here, we discuss ways of visualizing the scattering matrix that make its properties clear. Through a simulation-based case study incorporating shot noise, we shown how regularizing on this continuity enables the scattering matrix to be reconstructed from 4D scanning transmission electron microscopy (STEM) measurements from a single defocus value. Intriguingly, for crystalline samples, this process also yields the sample thickness to nanometer accuracy with no a priori knowledge about the sample structure. The reconstruction quality is gauged by using the reconstructed scattering matrix to simulate STEM images at defocus values different from that of the data from which it was reconstructed.

36 MATERIALS SCIENCE↗

Atomic-Resolution Study of Grain Boundaries in CdTe Using Scanning Transmission Electron Microscopy

CdTe is one of the most promising photovoltaic materials due to its near optimum band gap and a high absorption coefficient. However, the efficiencies of both champion poly-crystalline CdTe photovoltaic cells as well as production line modules are still significantly below the theoretical Shockley-Queisser limit of ~30%. Reduction of non-radiative recombination at grain boundaries is believed to be the key to improving the efficiency of polycrystalline CdTe-based solar cells. Here, atomistic-level characterization, including scanning transmission electron microscopy (STEM) and first principles density functional theory (DFT) modeling, is crucial in developing a fundamental understanding of how grain boundaries affect the solar cells’ efficiency.

14 SOLAR ENERGY↗

Particle and crystallite size effects on the modulated structure of multiferroic CaMn{sub 7}O{sub 12}

A systematic study of the atomic position modulation in polycrystalline CaMn{sub 7}O{sub 12} with different particle sizes (determined from scanning electron microscopy) and crystallite sizes (determined from X-ray diffraction) is reported. The morphology and phase composition are characterised by scanning electron microscopy, selected area electron diffraction and energy dispersive X-ray spectroscopy. The crystal structure and the atomic position modulation in polycrystalline CaMn{sub 7}O{sub 12} samples are explored with high-resolution synchrotron radiation based powder X-ray diffraction. The modulation vector and the modulation amplitudes observed at T=10 K do not change as a function of particle size, crystallite size and microstrain fluctuations. In addition, we report and discuss the formation of the additional CaMn{sub 4}O{sub 8} nanowire phase during high temperature annealing. - Graphical abstract: The particle size morphology of the multiferroic CaMn{sub 7}O{sub 12} has a weak influence on the atomic position modulation length and the amplitude of the atomic position modulation below T=250 K. Highlights: Black-Right-Pointing-Pointer Atomic position modulation occurs in CaMn{sub 7}O{sub 12} with different particle sizes. Black-Right-Pointing-Pointer The modulation length is the same for different CaMn{sub 7}O{sub 12} particle sizes. Black-Right-Pointing-Pointer Nanowire shaped crystals of CaMn{sub 4}O{sub 8} can be synthesized.

36 MATERIALS SCIENCE↗