Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Refractory material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Non-Classical Creep Behavior of Fusion-Cast Alumina Refractories

The compressive creep behavior of a typical 50% -/50% -alumina fusion-cast refractory block was examined as a function of temperature. Test temperatures (1450-1650oC) were chosen to correspond to those typical of service conditions, while relatively high compressive test stresses (0.6 and 1.0 MPa compared to 0.2-0.4 MPa which is typical of service) were chosen to promote exaggerated deformation and to more accurately measure the resulting creep strain. It was found that the measured creep strain responses in this alumina were a sum of (contracting) compressive creep strain and expansion strain due to time and temperature dependent microcracking. Long term, isothtermal expansion tests were also conducted, and their results allowed for the deconvolution of the compressive creep and expansion strains present in the measured creep strain test data. The analysis shows that despite complications associated with conflicting expansion and contraction effects, classical creep analysis may be used with this alumina refractory after the strains associated with the non-steady-state mechanism are considered and accounted for.

36 MATERIALS SCIENCE↗

Fabrication of Lanthanum Telluride 14-1-11 Zintl High-Temperature Thermoelectric Couple

The development of more efficient thermoelectric couple technology capable of operating with high-grade heat sources up to 1,275 K is key to improving the performance of radioisotope thermoelectric generators. Lanthanum telluride La3-xTe4 and 14-1-11 Zintls (Yb14MnSb11) have been identified as very promising materials. The fabrication of advanced high-temperature thermoelectric couples requires the joining of several dissimilar materials, typically including a number of diffusion bonding and brazing steps, to achieve a device capable of operating at elevated temperatures across a large temperature differential (up to 900 K). A thermoelectric couple typically comprises a heat collector/ exchanger, metallic interconnects on both hot and cold sides, n-type and ptype conductivity thermoelectric elements, and cold-side hardware to connect to the cold-side heat rejection and provide electrical connections. Differences in the physical, mechanical, and chemical properties of the materials that make up the thermoelectric couple, especially differences in the coefficients of thermal expansion (CTE), result in undesirable interfacial stresses that can lead to mechanical failure of the device. The problem is further complicated by the fact that the thermoelectric materials under consideration have large CTE values, are brittle, and cracks can propagate through them with minimal resistance. The inherent challenge of bonding brittle, high-thermal-expansion thermoelectric materials to a hot shoe material that is thick enough to carry the requisite electrical current was overcome. A critical advantage over prior art is that this device was constructed using all diffusion bonds and a minimum number of assembly steps. The fabrication process and the materials used are described in the following steps: (1) Applying a thin refractory metal foil to both sides of lanthanum telluride. To fabricate the n-type leg of the advanced thermoelectric couple, the pre-synthesized lanthanum telluride coupon was diffusion bonded to the metal foil using a thin adhesion layer. (2) Repeating a similar process for the 14-1-11 Zintl p-type leg of the advanced thermoelectric couple. (3) Bonding thick CTE-matched metal plates on the metallized lanthanum telluride and Yb14MnSb11 to form the hot and cold sides of the thermoelectric couple. The calculated conversion efficiency of such an advanced couple would be about 10.5 percent, about 35 percent better than heritage radioisotope thermoelectric technology that relies on Si-Ge alloys. In addition, unlike Si-Ge alloys, these materials can be combined with many other thermoelectric materials optimized for operation at lower temperatures to achieve conversion efficiency in excess of 15 percent (a factor of 2 increase over heritage technology).

Ravi, Vilupanur A.↗

Development of Fiber Laser Weld Parameters for Stainless Steel and Refractory Metals

Laser welds were made in 21-6-9 stainless steel, vanadium and tantalum using LLNL's new 6kW fiber laser to target 1 mm penetration depths. The materials were machined into flat coupon samples with standard step-joint geometries, and were welded in a continuous wave mode. The laser was characterized using the Primes laser beam diagnostic system so that the beams can be reproduced in the future. The optical configuration consisted of a 200 {micro}m fiber, 200 mm collimator and 250 mm focusing lens, which delivered electron-beam level power densities in the 5 to 20 kW/mm2 range. The three different materials required different power densities to produce the desired penetration, and this report summarizes the results of this screening study that was directed at developing a first approximation to the proper welding parameters for future work. The results show that 1 mm penetrations can be achieved using a 400W beam for 21-6-9 stainless steel, a 600W beam for vanadium, and a 1,100W beam for tantalum using sharp focus and a travel speed of 40 inch/min. Future welds should incorporate a trailing gas shield to prevent discoloration of the surface and to prevent oxygen and nitrogen pickup in the welds.

36 MATERIALS SCIENCE↗

Clinical Outcomes of Transcatheter Arterial Embolisation for Chronic Knee Pain: Mild-to-Moderate Versus Severe Knee Osteoarthritis

Purpose: This retrospective study was conducted to compare the clinical outcomes of transcatheter arterial embolisation for chronic knee pain in patients with mild-to-moderate versus severe knee osteoarthritis. Materials and Methods: This study included patients (n = 41) who were refractory to conservative treatments and who underwent transcatheter arterial embolisation using imipenem/cilastatin sodium between June 2017 and July 2018. A total of 71 knees, including 30 bilateral cases, were treated and categorised into two groups according to the Kellgren–Lawrence grade: mild-to-moderate osteoarthritis (n = 59, Kellgren–Lawrence grade 1–3) and severe osteoarthritis (n = 12, Kellgren–Lawrence grade 4). The clinical outcomes were measured by the visual analogue scale score. Results: There were no significant differences in age, body mass index or baseline visual analogue scale scores between the two groups. The mean visual analogue scale scores in the mild-to-moderate osteoarthritis group were significantly decreased at 1 day, 1 week, 1 month, 3 months, and 6-months (5.5 at baseline vs. 3.2, 3.1, 2.9, 2.2, and 1.9, after treatment; all P = .00). These improvements were maintained at a mean of 10 ± 3 months (range 6–19 months) post-treatment. The visual analogue scale scores were significantly decreased in the severe osteoarthritis group for 1 month post-treatment (6.3 at baseline vs. 4.1, 4.1, and 4.4 at 1 day, 1 week, and 1 month; all P < .01). However, a decrease in pain was not statistically significant from 3 to 6 months (5.4 and 5.9 at 3 months and 6 months, respectively). Conclusion: Transcatheter arterial embolisation effectively relieved pain in patients with mild-to-moderate osteoarthritis. In patients with severe osteoarthritis, pain severity decreased for 1 month but gradually increased to the initial severity score within 3 months. Level of Evidence: 4, Case series.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

The electronic structure of the CuRh{sub 1-x}Mg{sub x}O{sub 2} thermoelectric materials: An X-ray photoelectron spectroscopy study

A detailed X-ray photoelectron spectroscopy study has been performed for the CuRh{sub 1-x}Mg{sub x}O{sub 2} (x=0, 0.04 and 0.10) series for a better understanding of the role of the Mg{sup 2+} substitution on the electrical properties and the value of the Seebeck coefficient. This study is based on an analysis of different compounds such as Rh{sub 2}O{sub 3}, Sr{sub 2}RhO{sub 4} and CuCrO{sub 2} in order to characterize different oxidation states (Rh{sup 3+} and Rh{sup 4+} in octahedral oxygen environment and Cu{sup +} in a dumbbell O-Cu-O coordination). The Cu2p signal of copper in the non-doped compounds CuCrO{sub 2} and CuRhO{sub 2} reveals different electronic structures. An evolution of the Cu2p core signal with the increase of Mg{sup 2+} content in the CuRh{sub 1-x}Mg{sub x}O{sub 2} is highlighted by XPS. The differences observed, especially for the Cu2p core peaks are discussed for the non-doped compounds CuCrO{sub 2} and CuRhO{sub 2} as for the CuRh{sub 1-x}Mg{sub x}O{sub 2} series upon Mg{sup 2+} substitution. - Graphical Abstract: The role of the Mg substitution in the CuRh{sub 1-x}Mg{sub x}O{sub 2} as a function of x (x=0, 0.04 and 0.1) has been investigated by following the evolution of the Cu2p spectra obtained by X-ray photoelectron spectroscopy. The filled peaks are assigned to main peak A and A{sub sat} satellites, the hatched peaks to main peak B and B{sub sat} satellites. Highlights: > XPS investigations on CuRh{sub 1-x}Mg{sub x}O{sub 2} (x=0-0.04-0.1) delafossites. > Influence of magnesium doping on to the electrical properties and the electronic structures. > Copper cation keeps two oxidation states Cu{sup +}/Cu{sup 2+} in the CuRh{sub 1-x}Mg{sub x}O{sub 2} (x=0-0.4-0.1) with an increase of the Cu{sup 2+}/Cu ratio with the x value. > Cu layer seems to contribute to complex electrical transport in such delafossites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of XCT for Matrix Density Measurement of Particle Fuel Forms

Particle fuel forms generally consist of a dispersion of fuel, such as tristructural isotropic (TRISO) particles, within a refractory matrix (e.g., graphite or silicon carbide). The density of matrix materials for particle fuel forms is of interest for modeling fuel form strength and thermal properties and may be specified as a quality control parameter, depending on reactor design. Some of the uncertainty associated with traditional, manual approaches can be eliminated by performing x-ray computed tomography (XCT) on the fuel forms and applying image processing methods to generate a precise count of the number of particles. This also removes the need to include determination of particle count within each individual fuel form during fabrication. Unfortunately, reconstruction artifacts from high-Z uranium-bearing kernels prevent accurate measurement of individual particle volumes using this approach, so the use of mean particle mass and volume are still necessary for computation of average fuel form matrix density. This method of using XCT to count particles in individual fuel form for determination of average matrix density was applied to three archived compacts from the Advanced Gas Reactor Fuel Development and Qualification (AGR)-1 campaign, four archived compacts with uranium carbide/uranium oxide (UCO) TRISO from the AGR-2 campaign, and three archived UO 2 -TRISO compacts from the AGR-2 campaign. The resulting density values were compared with those previously reported, showing slight changes due to uncertainties in the previously used number of particles in each of these cylindrical, graphite matrix compacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Interdisciplinary research concerning the nature and properties of ceramic materials

Research projects involving the development of ceramic materials are discussed. The following areas of research are reported: (1) refractory structural ceramics, (2) solid electrolyte ceramics, and (3) ceramic processing. The laboratory equipment used and the procedures followed for various development and evaluation techniques are described.

Mueller, J. I.↗

Fibrous refractory composite insulation

Family of high-temperature, low-density refractory composite insulations made from aluminoborosilicate and silica fibers has insulating material with improved mechanical and thermal properties. Composition is useful for reusable heat-shield materials.

Goldstein, H. E.↗

Adherence of sputtered titanium carbides

The study searches for interface treatment that would increase the adhesion of TiC coating to nickel- and titanium-base alloys. Rene 41 (19 wt percent Cr, 11 wt percent Mo, 3 wt percent Ti, balance Ni) and Ti-6Al-4V (6 wt percent Al, 4 wt percent V, balance Ti) are considered. Adhesion of the coatings is evaluated in pin-and disk friction tests. The coatings and interface regions are examined by X-ray photoelectron spectroscopy. Results suggest that sputtered refractory compound coatings adhere best when a mixed compound of coating and substrate metals is formed in the interfacial region. The most effective type of refractory compound interface appears to depend on both substrate and coating material. A combination of metallic interlayer deposition and mixed compound interface formation may be more effective for some substrate coating combinations than either alone.

Brainard, W. A.↗

Factors Influencing Dwell Fatigue Cracking in Notches of Powder Metallurgy Superalloys

The influences of heat treatment and cyclic dwells on the notch fatigue resistance of powder metallurgy disk superalloys were investigated for low solvus high refractory (LSHR) and ME3 disk alloys. Disks were processed to produce material conditions with varied microstructures and associated mechanical properties. Notched specimens were first subjected to baseline dwell fatigue cycles having a dwell at maximum load, as well as tensile, stress relaxation, creep rupture, and dwell fatigue crack growth tests at 704 C. Several material heat treatments displayed a bimodal distribution of fatigue life with the lives varying by two orders-of-magnitude, while others had more consistent fatigue lives. This response was compared to other mechanical properties, in search of correlations. The wide scatter in baseline dwell fatigue life was observed only for material conditions resistant to stress relaxation. For selected materials and conditions, additional tests were then performed with the dwells shifted in part or in total to minimum tensile load. The tests performed with dwells at minimum load exhibited lower fatigue lives than max dwell tests, and also exhibited early crack initiation and a substantial increase in the number of initiation sites. These results could be explained in part by modeling evolution of peak stresses in the notch with continued dwell fatigue cycling. Fatigue-environment interactions were determined to limit life for the fatigue cycles with dwells.

Gabb, T. P.↗

Ultrahigh Performance Metallic Turbine Blades for Extreme Environments

In ULTIMATE Phase-I, The Boeing Company and Alloyed Inc. aimed to produce ultrahigh performance metallic extreme environment turbine blades with a base blade alloy capable of inert operation at 1300C, and a maximum coated blade operating temperature up to 1800C. High-performance structural designs for extreme service conditions place additional demands on the present material capability and can potentially outpace the current state-of-the-art in the alloy design space and metal processing. As a part of exploration and adoption of novel concepts for material maturation, the team explored a series of capable base novel refractory complex concentrated alloy (RCCA) compositions and potential powder enhancements. Advanced manufacturing processes, with a focus on laser powder bed fusion additive manufacturing (AM) and powder metallurgy (PM) approaches, were applied to consolidate new alloys and for near net shape processing of blades from the base RCCA.

Yousefiani, Ali↗

Design of an alumina forming coating for Nb-base refractory alloys

Refractory multi-principal element alloys (RMPEAs) promise to significantly enhance gas turbine engine efficiency, but their poor oxidation performance inhibits their implementation. Alumina-forming bond coat alloys can provide oxidation protection, but discovering suitable chemistries remains a challenge. We employed a design methodology that screens for alumina-formation capability using Al activity and phase constitution predictions from CalPhaD (Thermo-Calc). Alloy down-selection from approximately 7,800 alloys in the Nb-Si-Ti-Al-Hf system was conducted via analysis of calculated thermodynamic properties with number-density topology style maps. This approach is validated by creating and testing the composition Nb 12 Si 23 Ti 24 Al 36 Hf 5 , which forms protective alumina scales up to 1400 °C and resists pesting at 800 °C. Further, the alloy has an average coefficient of thermal expansion of ~10.1 ppm/K, making it well matched to Nb-based refractory alloys. The methodology will be useful for the design of coatings for RMPEAs, enabling their implementation and significant efficiency benefits sooner.

36 MATERIALS SCIENCE↗

Additive Manufacturing of Ultrahigh Temperature Refractory Metal Alloys

The project advances the manufacture of RMA for ultrahigh-temperature service with three main innovations: a thermodynamically derived high-throughput AM synthesis and characterization using reactive synthesis of elemental powders, a new dimensional number to predict processing parameters, and a novel processing scheme for the fabrication of components with functional grading microstructures. With these advances, the project demonstrates in Phase I the manufacture of RMAs exhibiting room temperature compression ductility above 20%, room temperature fracture toughness above 10 MPam 0.5 , and the fabrication of tensile test samples that have a transformative impact on the manufacturing of RMAs by enabling cost-efficient and large-scale fabrication of components.

33 ADVANCED PROPULSION SYSTEMS↗

Effect of cycled combustion ageing on a cordierite burner plate

A combination of {sup 57}Fe-Moessbauer spectroscopy and X-ray Powder Diffraction analysis has been employed to study modifications in chemical and mechanical stability occurring in a cordierite burner aged under combustion conditions which simulate the working of domestic boilers. Moessbauer study shows that Fe is distributed into the structural sites of the cordierite lattice as Fe{sup 2+} and Fe{sup 3+} ions located mostly at octahedral sites. Ferric oxide impurities, mainly hematite, are also present in the starting cordierite material accounting for {approx_equal}40% of the total iron phases. From Moessbauer and X-ray diffraction data it can be deduced that, under the combustion conditions used, new crystalline phases were formed, some of the substitutional Fe{sup 3+} ions existing in the cordierite lattice were reduced to Fe{sup 2+}, and ferric oxides underwent a sintering process which results in hematite with higher particle size. All these findings were detected in the burner zone located in the proximity of the flame and were related to possible chemical reactions which might explain the observed deterioration of the burner material. Research Highlights: {yields}Depth profile analyses used as a probe to understand changes in refractory structure. {yields}All changes take place in the uppermost surface of the burner, close to the flame. {yields}Reduction to Fe{sup 2+} of substitutional Fe{sup 3+} ions and partial cordierite decomposition. {yields}Heating-cooling cycling induces a sintering of the existing iron oxide particles. {yields}Chemical changes can explain the alterations observed in the material microstructure.

36 MATERIALS SCIENCE↗

Effects of Ti, Zr, and Hf on the Phase Stability of Mo-Mo 3 Si+Mo 5 SiB 2 Alloys at 1600 C

Understanding the stability of the three-phase Mo{_}+Mo{sub 3}Si+Mo{sub 5}SiB{sub 2} region is important for alloy design of Mo-Si-B-based refractory metal intermetallic composites. In this work, thermodynamic modeling is coupled with guided experiments to study phase stability in this three-phase region of the Mo-Si-B-X (X = Ti, Zr, Hf) system. Both the calculated and experimental results show that additions of Zr and Hf limit significantly the stability of the three-phase region because of the formation of the ternary phases MoSiZr and MoSiHf, while Ti addition leads to a much larger region of stability for the three-phase equilibrium.

36 MATERIALS SCIENCE↗

Novel Processing of Unique Ceramic-Based Nuclear Materials and Fuels

Advances in nuclear reactor technology and the use of gas-cooled fast reactors require the development of new materials that can operate at the higher temperatures expected in these systems. These include refractory alloys base on Nb, Zr, Ta, Mo, W, and Re; ceramics and composites such as those based on silicon carbide (SiCf-SiC); carbon-carbon composites; and advanced coatings. Besides the ability to handle higher expected temperatures, effective heat transfer between reactor componets is necessary for improved efficiency. Improving thermal conductivity of the materials used in nuclear fuels and other temperature critical components can lower the center-line fuel temperature and thereby enhance durability and reduce the risk of premature failure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Boron capture stabilizing the diffusion barriers in a two-step Mo-Si-B coated refractory multi-principal element alloy

A Mo-Si-B based coating has been applied on a refractory multi-principal element alloy (RMPEA) using a two-step coating strategy and has endured more than 750 hours of thermal cycling oxidation exposure between room temperature to 1300°C with a minimal weight change. Here, the formation of the Mo 5 SiB 2 diffusion barrier in the coating prevents the inward diffusion of the coating components. Then, boron is captured by the RMPEA, resulting in the formation of a solid solution X 5 SiB 2 (X= W, Mo, Ta, Nb, V) layer and an RMPEA-B boride layer underneath it that acts as the second diffusion barrier.

36 MATERIALS SCIENCE↗