Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reentry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Thermal Testing of Ablators in the NASA Johnson Space Center Radiant Heat Test Facility

A spacecraft's thermal protection system (TPS) is required to survive the harsh environment experienced during reentry. Accurate thermal modeling of the TPS is required to since uncertainties in the thermal response result in higher design margins and an increase in mass. The Radiant Heat Test Facility (RHTF) located at the NASA Johnson Space Center (JSC) replicates the reentry temperatures and pressures on system level full scale TPS test models for the validation of thermal math models. Reusable TPS, i.e. tile or reinforced carbon-carbon (RCC), have been the primary materials tested in the past. However, current capsule designs for MPCV and commercial programs have required the use of an ablator TPS. The RHTF has successfully completed a pathfinder program on avcoat ablator material to demonstrate the feasibility of ablator testing. The test results and corresponding ablation analysis results are presented in this paper.

Del Papa, Steven↗
NASA NTRS2020

Aeroheating Measurements of BOLT Aerodynamic Fairings and Transition Module

The Air Force Office of Scientific Research (AFOSR) has sponsored the Boundary Layer Transition (BOLT) Experiments to investigate hypersonic boundary layer transition on a low-curvature, concave surface with swept leading edges. This paper presents aeroheating measurements on a subscale model of the BOLT Flight Geometry, aerodynamic fairings, and Transition Module (TSM) in the NASA Langley 20-Inch Mach 6 Air Tunnel. The purpose of the test was to investigate and identify any areas of localized heating on the TSM for inclusion in the BOLT Critical Design Review (CDR). Surface heating distributions were measured using global phosphor thermography, and data were obtained for a range of model attitudes and free stream Reynolds numbers. Measurements showed low heating on the fairings and TSM. Additional analysis was completed after the CDR to compare heating on the TSM for the nominal BOLT vehicle reentry angle-of-attack with heating on the TSM for possible reentry angle-of-attack excursions. The results of this analysis were used in conjunction with thermal analyses from Johns Hopkins Applied Physics Lab (JHU/APL) and the Air Force Research Laboratory (AFRL) to assess the need for thermal protection on the flight vehicle TSM.

Rieken, Elizabeth F.↗
NASA NTRSDate not supplied

NASA Orbital Debris Mitigation Requirements Applied to Batteries

This presentation reviews the current state of NASA orbital debris mitigation requirements with respect to spacecraft batteries. NASA requirements address the probability of accidental explosion during and after mission operations, and probability of human casualty resulting from reentry. Excluding post-mission explosion, these probabilities must be evaluated against quantitative limits. Reentry demisability models provide the quantitative results to assess compliance with the casualty threshold. Some projects show compliance with the explosion requirement using manufacturers’ stated component or assembly reliabilities, while others cite similarity with past accepted projects. With the required threshold included in the USG ODMSP, NASA encourages the use of – and seeks – standardized methods to help quantify the probability of accidental explosion.

Batteries↗
NASA NTRSDate not supplied

NASA Efforts to Explore Additively Manufactured Thermal Protection Systems

Development of the thermal protection system (TPS) needed to protect external and internal surfaces during launch, ascent, cruise, and reentry, is a very specialized field with expertise developed over seven decades and has enabled successful robotic as well as human exploration. Well known examples are: 1) the ablative heatshield that protected Apollo Astronauts during reentry in 1960’s, 2) reusable TPS used on the Space Shuttle Orbiter, which is now sought after by commercial space industry, and 3) hot structures, such as Carbon-Carbon and other high temperature materials needed to operate control surfaces and sharp leading edges during hypervelocity flight. TPS function demands fail-safe design to ensure mission success. One TPS does not fit all, and each application requires a unique material along with manufacturing and integration approach. TPS mass is a key metric. A robust but inefficient TPS reduces payload mass. Mission- and domain-unique TPS development and flight certification efforts have been expensive with long lead times. As a result, there are limited TPS choices with high cost. For future commercial efforts to be successful, the ability to rapidly develop TPS, based on specific needs and at a lower cost, without compromising either mass efficiency or functionality is necessary. NASA is looking into this. Additive manufacturing (AM) techniques have shown their utility in making complex parts and, through automation, the potential to reduce cost and schedule in some applications. The promise of additive manufacturing to TPS, while exciting, is unexplored. In the past several years, NASA has made exploratory investments in internal development as well as in small business and universities through SBIR and STTR programs. In addition, NASA is bringing together the TPS as well as Additive Manufacturing communities to explore approaches to prioritize focus areas for broad benefits. The very first “Additively Manufactured Thermal Protection System Workshop,” to be held at NASA Johnson Space Center in Houston at the end of March of this year, is the culmination of a year-long effort to engage the research, development, and user communities involved in both TPS as well as additive manufacturing. The workshop participants include representatives from large and small commercial space industry, DoD, Federally Funded Research and Development Centers, University Researchers and NASA personnel. The proposed talk will highlight future TPS needs of both emerging commercial and Government interests, NASA’s development efforts in additively manufactured TPS, and the findings and recommendations from the first AM TPS Workshop.

Ethiraj Venkatapathy↗
NASA NTRSDate not supplied

Characterizing Char Rate and Extent in Fiber-Reinforced Plastics Using X-ray Computed Tomography

Orbital debris is a growing problem for the space industry and the world in general, and an important component of the problem is what happens when that debris reenters the Earth’s atmosphere. With more spacecraft opting for fiber-reinforced polymer (FRP) components, we need to understand the thermal destruction process of these materials during an atmospheric reentry and how much of the material can survive to impact the ground. The NASA Orbital Debris Program Office (ODPO) has developed a new charring model for FRP components to be integrated into the latest version of the Object Reentry Survival Analysis Tool (ORSAT). To validate this new model, the ODPO performed several test series using the Inductively Coupled Plasma (ICP) Torch facility at UT Austin. To measure the extent of charred material at different conditions, some of the test samples were scanned using x-ray computed tomography (CT) by the Astromaterials Curation Lab at Johnson Space Center. 3D image analysis was then used to calculate the volume and density of the char in each test sample. This paper presents the image analysis methodology, an assessment of the accuracy of the data analysis, and a comparison with calculations using the ORSAT charring model.

Benton Greene↗
NASA NTRSDate not supplied

Recent Langley Aerothermodynamic Laboratory Testing (2019-2022)

In support of flight programs, multiple wind tunnel entries were conducted on reentry vehicle configurations to investigate blunt body aeroheating environments. Blunt body block thermal protection system (TPS) roughness, the Low-Earth Orbit Flight Test of an Inflatable Decelerator aeroshell scalloping, and a woven TPS all were tested to determine the effects of those parameters on increased surface heating to the vehicle. Commercial Crew Program studies also utilized the speed and ease of testing in the LAL to analyze parametric databases of low-earth reentry configurations, like the Boeing CST-100, and vehicles designed to travel to the moon or Mars, such as the SpaceX Starship. LAL wind tunnel investigations also supported several DoD and AFRL flight projects, such as HIFiRE 6 and BOLT. External customers leveraged the LAL testing capability to advance their research programs, including UPSTAR, RocketLab, and Lawrence Livermore National Laboratory. Academia groups benefitted from the inexpensive cost to test in the tunnels for many university collaborations, such as studies conducted in partnership with the University of Maryland on a flat plate, using a pressure rake and investigating fluid structure interactions. Multiple studies in collaboration with Purdue considered boundary layer transition on various cone configurations. Another study was conducted using a cone with shaped roughness elements borrowed from the Arnold Engineering Development Complex. Internal testing included studies using a phosphor thermography system that can measure higher temperatures than the current LAL phosphor capability and a characterization study of the noise in the wind tunnel flow. The breadth of testing across research and commercial paradigms, both internal and external to NASA, different configurations, a variety of test techniques and aerodynamic and aerothermal environments will be discussed in this overview presentation of the recent work conducted in the LAL.

wind tunnel test↗
NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Gregory T Swanson↗
NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Greg Swanson↗
NASA NTRSDate not supplied

Ballistic Lunar Return Trajectories for Sustainable Cargo Return and Entry System Technology Development

As part of the sustained approach for the lunar Gateway and Artemis program as a whole, NASA is extending the logistics supply chain beyond low Earth orbit and to the Moon. This supply chain includes the possibility of lunar sample and cargo return. To enable these future return missions, the possibility for incorporating demonstration payloads including various entry, descent, and landing technologies is examined. Possible implementations include deployable entry vehicles, high speed sample return capsules, aeroassist technologies, and control technologies for guided hypersonic flight. The mission concepts utilize the secondary payload capabilities provided on a relatively low-cost logistic module. The logistic module may perform close Earth flyby, pointing, and release of return systems prior to disposal, with reentry velocities for payloads on the order of 11.5 km/sec. In this paper, we study the various return mission architectures available during the Artemis program to define the range of mission possibilities. Potential options include a reusable logistics module using a hypersonic inflatable aerodynamic decelerator, externally mounted entry system vehicle technologies, and a reusable sample return vehicle using a similar inflatable architecture with a feathered configuration with applied aerodynamic control. In these cases, the use of a ballistic lunar return trajectory is assumed, and a sensitivity analysis of midcourse corrections and the possibility of a lunar gravity assist for refining Earth entry interface points is provided. Furthermore, a novel controller for controlling a vehicle during reentry imposing heating limitations is introduced.

Matthew M. Wittal↗
NASA NTRSDate not supplied

Heritage to Flight; The Test Program that Brought an Inflation System Back to Life for the Low Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID)

Following the success of the Inflatable Reentry Vehicle Experiment-3 (IRVE-3) project, the Terrestrial Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Orbital Reentry (THOR) project was stood up with a “built to print” Inflation System utilizing the IRVE-3 flight spares. When THOR was canceled, this Inflation System had already been tested and assembled, ready for use. Thus, when the Low Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was spun up, the THOR system seemed like a good candidate to salvage flight ready hardware. There were, however, some key differences in the IRVE/THOR system and the LOFTID one. LOFTID’s HIAD was two times the size of IRVE for starters and would require much higher flows to accommodate inflating such an article within a specific timeframe. With new requirements and a tight schedule, the LOFTID Inflation team set to work to verify flight readiness under LOFTID conditions and eliminate the need to requalify new hardware. LOFTID, utilizing an Inflation System built primarily hardware from IRVE-3 spares, successfully flew in November of 2022. This paper will outline the mission differences, the test campaign used to prepare LOFTID’s Inflation System for flight, and some lessons learned in repurposing older hardware.

Inflation System↗
NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

On November 10, 2022, NASA launched the Low-earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle as a secondary payload mounted inside the launch vehicle adaptor on an Atlas V out of the Vandenburg Space Force Base (VSFB). The primary payload, Joint Polar Satellite System-2 (JPSS-2), was delivered successfully to a sun synchronous trajectory shortly after launch, at which point the Centaur upper stage performed a burn to de-orbit the system. Once on the desired trajectory to enter the atmosphere the payload adaptor canister was ejected by the payload adapter separation system to expose the packed LOFTID vehicle, then the LOFTID aeroshell, a Hypersonic Inflatable Aerodynamic Decelerator (HIAD), was deployed and inflated as planned. The Centaur pointed the LOFTID vehicle to the desired attitude to enter the atmosphere, spun the assembly to roughly three rpm, and separated the reentry vehicle. The LOFTID vehicle entered the atmosphere over Alaska at >8km/sec and decelerated as designed demonstrating stable flight from hypersonic entry through subsonic parachute deployment. On-board visible light cameras captured the reactions of the heatshield through all phases of flight, and co-located infrared light cameras captured the temperature distribution of the aft side of the heat shield anchored to a distribution of thermocouples on the inflatable structure (IS) in the field of view. Thermocouples were also embedded in the forward side of the aeroshell both in the Flexible Thermal Protection System (FTPS) as well as the IS. Heat Flux Gages and Pressure Transducers measured the heating rate and surface pressure experienced by the rigid nose of the reentry vehicle. Loadcells measured the interface loads between the IS and the rigid centerbody. This paper will discuss many of the key instruments flown on the successful LOFTID technology demonstration mission and will provide some high level results, while pointing to more detailed papers on the post-flight analyses.

Gregory T Swanson↗
NASA NTRSDate not supplied

LOFTID (Low-Earth Orbit Flight Test of an Inflatable Decelerator) PASS (Payload Adapter Separation System) Design & Qualification

On November 10, 2022, NASA, in partnership with United Launch Alliance (ULA), launched Low-earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) as a secondary payload on an Atlas V Centaur out of the Vandenburg Space Force Base (VSFB). After successfully delivering the primary payload, Joint Polar Satellite System-2 (JPSS-2), to a sun synchronous trajectory, the Centaur upper stage reoriented LOFTID onto the desired reentry trajectory. After conducting a de-orbit burn to enter the atmosphere the Payload Adaptor was ejected to expose the packed LOFTID vehicle. The LOFTID Hypersonic Inflatable Aerodynamic Decelerator (HIAD) was deployed and inflated. The Centaur pointed LOFTID to the desired entry attitude and spun the vehicle up to roughly three rpm before separating the reentry vehicle over the Middle East. The LOFTID vehicle flew freely before reentering the atmosphere over Alaska at >8km/sec and decelerating as designed. LOFTID demonstrated stable flight from hypersonic entry through subsonic parachute deployment. LOFTID was enabled by a mission-unique Payload Adapter Separation System (PASS) which separated the Payload Adapter prior to the start of the LOFTID flight demonstration, allowing the launch vehicle to accommodate a superstack of two independent, similarly sized payloads. This paper will discuss the design, development, and qualification effort of the LOFTID PASS.

Sean M Hancock↗
NASA NTRSDate not supplied

Heritage to Flight: The Test Program that Brought an Inflation System Back to Life for LOFTID

Following the success of the Inflatable Reentry Vehicle Experiment-3 (IRVE-3) project, the Terrestrial Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Orbital Reentry (THOR) project was stood up with a “built to print” Inflation System utilizing the IRVE-3 flight spares. When THOR was canceled, this Inflation System had already been tested and assembled, ready for use. Thus, when the Low Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was spun up, the THOR system seemed like a good candidate to salvage flight ready hardware. There were, however, some key differences in the IRVE/THOR system and the LOFTID one. LOFTID’s HIAD was two times the size of IRVE for starters and would require much higher flows to accommodate inflating such an article within a specific timeframe. With new requirements and a tight schedule, the LOFTID Inflation team set to work to verify flight readiness under LOFTID conditions and eliminate the need to requalify new hardware. LOFTID, utilizing an Inflation System built primarily hardware from IRVE-3 spares, successfully flew in November of 2022. This paper will outline the mission differences, the test campaign used to prepare LOFTID’s Inflation System for flight, and some lessons learned in repurposing older hardware.

Inflation System↗
NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

On November 10, 2022, NASA launched the Low-earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle as a secondary payload mounted inside the launch vehicle adaptor on an Atlas V out of the Vandenburg Space Force Base (VSFB). The primary payload, Joint Polar Satellite System-2 (JPSS-2), was delivered successfully to a sun synchronous trajectory shortly after launch, at which point the Centaur upper stage performed a burn to de-orbit the system. Once on the desired trajectory to enter the atmosphere the payload adaptor canister was ejected by the payload adapter separation system to expose the packed LOFTID vehicle, then the LOFTID aeroshell, a Hypersonic Inflatable Aerodynamic Decelerator (HIAD), was deployed and inflated as planned. The Centaur pointed the LOFTID vehicle to the desired attitude to enter the atmosphere, spun the assembly to roughly three rpm, and separated the reentry vehicle. The LOFTID vehicle entered the atmosphere over Alaska at >8km/sec and decelerated as designed demonstrating stable flight from hypersonic entry through subsonic parachute deployment. On-board visible light cameras captured the reactions of the heatshield through all phases of flight, and co-located infrared light cameras captured the temperature distribution of the aft side of the heat shield anchored to a distribution of thermocouples on the inflatable structure (IS) in the field of view. Thermocouples were also embedded in the forward side of the aeroshell both in the Flexible Thermal Protection System (FTPS) as well as the IS. Heat Flux Gages and Pressure Transducers measured the heating rate and surface pressure experienced by the rigid nose of the reentry vehicle. Loadcells measured the interface loads between the IS and the rigid centerbody. This paper will discuss many of the key instruments flown on the successful LOFTID technology demonstration mission and will provide some high level results, while pointing to more detailed papers on the post-flight analyses.

spacecraft design↗
NASA NTRSDate not supplied

Heritage to Flight: The Test Program that Brought an Inflation System Back to Life for LOFTID

Following the success of the Inflatable Reentry Vehicle Experiment-3 (IRVE-3) project, the Terrestrial Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Orbital Reentry (THOR) project was stood up with a “built to print” Inflation System utilizing the IRVE-3 flight spares. When THOR was canceled, this Inflation System had already been tested and assembled, ready for use. Thus, when the Low Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was spun up, the THOR system seemed like a good candidate to salvage flight ready hardware. There were, however, some key differences in the IRVE/THOR system and the LOFTID one. LOFTID’s HIAD was two times the size of IRVE for starters and would require much higher flows to accommodate inflating such an article within a specific timeframe. With new requirements and a tight schedule, the LOFTID Inflation team set to work to verify flight readiness under LOFTID conditions and eliminate the need to requalify new hardware. LOFTID, utilizing an Inflation System built primarily hardware from IRVE-3 spares, successfully flew in November of 2022. This paper will outline the mission differences, the test campaign used to prepare LOFTID’s Inflation System for flight, and some lessons learned in repurposing older hardware.

Inflation System↗
NASA NTRS2024

The NASA Orbital Debris Program Office - In Service of Space Safety

Since the NASA Orbital Debris Program Office’s (ODPO) founding in 1979 at the Johnson Space Center in Houston, Texas, it has been at the forefront of orbital debris research, modeling, and policy development. The ODPO has worked in collaboration with NASA and other U.S. government missions since the 1980s to mitigate the growth of the orbital debris environment and protect the population of the Earth. Two main products from the ODPO, the Orbital Debris Engineering Model (ORDEM) and the Debris Assessment Software (DAS), are frequently among the top three most-downloaded software packages from the NASA Software Catalog. These products are provided free of charge to the public in furtherance of the goal to ensure that new space missions, in compliance with NASA’s orbital debris mitigation requirements, are developed, operated, and disposed of responsibly. In addition to these external-facing software tools, the ODPO maintains high-fidelity internal tools for reentry simulation (the Object Reentry Survival Analysis Tool, ORSAT), short-term risk assessment for robotic and human spaceflight missions (the Satellite Breakup Risk Assessment Module, SBRAM), among others. Using data from the ORDEM model, as well as using the Meteoroid Environment Model (MEM) developed by the Meteoroid Environment Office (MEO) at NASA’s Marshall Space Flight Center, the Hypervelocity Impact Technology (HVIT) team uses the BUMPER code to assess penetration risk to space vehicles in Earth orbit and beyond. This paper will discuss the services that the ODPO and HVIT provide, from mission concept development through end-of-mission, for NASA-related and commercial missions.

Chris Ostrom↗