Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Use of Polarization Lidar for Investigation of Meteorological Formations

This paper presents the results of theoretical and experimental, investigations of depolarization characteristics of different meteorological formations. Experimental investigations are carried out with a monostatic lidar. The ruby laser radiation is polarized in a vertical plane. The radiation reflected is accepted by a lens system of 150 rom in diameter and a viewing angle of 12' and further it is divided by Wollaston prism into the components polarized orthogonally. In this case the principal plane of the prism is exposed parallel with the laser polarization plane. Investigations show the degree of radiation polarization, reflected from water clouds, to be changed within 1/0.7 (seldom up to 0.6) depending on their density. In most cases a signal reflected from the cloud leading edge is polarized completely. The time shift is observed between polarized and crosspolarized components of a Fignal, reflected from a cloud, depending on the density of a meteorological object. While penetrating into the cloud depth a degree of polarization decreases up to 0.8-0.7, and the character of this decrease is different for various types of clouds. For crystal clouds the shift between the components of the reflected signal is not observed and the magnitude of polarization degree amounts to 0.1/0.3 in comparison with water clouds. The polarization degree of radiation reflected by fog is not less than 0.6, and that in the rains of average intensity (about 5 mm/h) is always about 1. The authors have suggested an algorithm of numerical solution of nonstationary transfer equation in the vector form to forecast the influence of multiple scattering effects on polarization characteristics of the lidar light signal. The method of statistical simulation (Monte-Carlo technique) forms the basis of the algorithm. Numerical estimates obtained for a model of stratocumulus at lambda = 0.6943 microns under boundary conditions close to the conditions of natural experiment being discussed proved to be in a good agreement with the results of observation. Specifically, Fig. 1 shows the profiles of polarization (p) versus depth (L) of the following drop formations: fog (curve 1) with horizontal meteorological visibility of 4 km two stratocumulus at a height of 1100 m with the attenuation factors delta = 0.01m(exp -1) (curve 2) and delta = 0.05m(exp -1) (curve 3). Curve 3 shows the results of numerical estimates and the value of their statistical error.

Balin, Yu. S.↗
NASA NTRS2016

Using FUN3D for Aeroelastic, Sonic Boom, and AeroPropulsoServoElastic (APSE) Analyses of a Supersonic Configuration

An overview of recent applications of the FUN3D CFD code to computational aeroelastic, sonic boom, and aeropropulsoservoelasticity (APSE) analyses of a low-boom supersonic configuration is presented. The overview includes details of the computational models developed including multiple unstructured CFD grids suitable for aeroelastic and sonic boom analyses. In addition, aeroelastic Reduced-Order Models (ROMs) are generated and used to rapidly compute the aeroelastic response and utter boundaries at multiple flight conditions.

Silva, Walter A.↗
NASA NTRS2016

A Status Review of the Commercial Supersonic Technology (CST) Aeroservoelasticity (ASE) Project

An overview of recent progress regarding the computational aeroelastic and aeroservoelastic (ASE) analyses of a low-boom supersonic configuration is presented. The overview includes details of the computational models developed to date with a focus on unstructured CFD grids, computational aeroelastic analyses, sonic boom propagation studies that include static aeroelastic effects, and gust loads analyses. In addition, flutter boundaries using aeroelastic Reduced-Order Models (ROMs) are presented at various Mach numbers of interest. Details regarding a collaboration with the Royal Institute of Technology (KTH, Stockholm, Sweden) to design, fabricate, and test a full-span aeroelastic wind-tunnel model are also presented.

Silva, Walter A.↗
NASA NTRS1993

Magellan Final Science Reports

This volume is a brief summary of the scientific results of the Magellan Venus mapping mission as reported by the Magellan science investigators. Magellan has exceeded all of its mission objectives by obtaining high resolution radar images, surface elevation, and radiometry for more than 98% of the planet. The amount of stereo data gathered on Venus is more than that available for any other planet. Magellan's fourth cycle collected gravity data from an elliptical orbit to provide information on the relationships between surface features and the interior of the planet. With the successful completion of the aerobraking experiment, the spacecraft, in its lower orbit around Venus, has captured high resolution gravity near the poles from the nearly circular orbit. Every attempt has been made to provide useful documentation for the complete Magellan data set. Magellan data have been released to the public through the Planetary Data System (PDS) and the National Space Science Data Center (NSSDC) in photographs, lithos, brochures, digital form, and compact discs. With the release of Magellan data on the compact disc read-only-memory (CD-ROM) a revolutionary new way of doing science has resulted. This technology provides a way to store, distribute and access large volumes of data. The Magellan science investigators have utilized this wealth of data to provide answers to questions we have been asking for a long time. I would like to personally thank everyone on the Magellan team for the success of this important mission, a mission that has revealed information that will help us to better understand our own Planet Earth.

Thompson, Thomas W.↗
NASA NTRS2017

Computational Results for the KTH-NASA Wind-Tunnel Model Used for Acquisition of Transonic Nonlinear Aeroelastic Data

A status report is provided on the collaboration between the Royal Institute of Technology (KTH) in Sweden and the NASA Langley Research Center regarding the aeroelastic analyses of a full-span fighter configuration wind-tunnel model. This wind-tunnel model was tested in the Transonic Dynamics Tunnel (TDT) in the summer of 2016. Large amounts of data were acquired including steady/unsteady pressures, accelerations, strains, and measured dynamic deformations. The aeroelastic analyses presented include linear aeroelastic analyses, CFD steady analyses, and analyses using CFD-based reduced-order models (ROMs).

Silva, Walter A.↗
NASA NTRS2018

Multidisciplinary Design Optimization and Cruise Mach Number Study of Truss-Braced Wing Aircraft

The Subsonic Ultra Green Aircraft Research (SUGAR) Phase III was led by Dr. Rakesh K. Kapania and Dr. Joseph A. Schetz at the Multidisciplinary Analysis and Design Center for Advanced Vehicles, Department of Aerospace and Ocean Engineering, Virginia Tech, Blacksburg VA. The research was performed from December 2014 to December 2015. Three major areas were investigated: Multidisciplinary Design Optimization (MDO) studies of truss braced wing (TBW) and strut braced wing (SBW) vehicles at cruise Mach numbers of 0.7 and 0.8 for a flight mission similar to current market single aisle configurations. The performance and the characteristics of the optimized vehicles were compared to the SUGAR Phase II TBW vehicle. These results were obtained without applying any of the extended transonic aerodynamic and aeroelastic tools that will be discussed later. It was found that the cruise Mach number has a large effect on the best “truss” configuration. At Mach 0.7, an SBW has a better fuel consumption and better take-off gross weight (TOGW). However, at Mach 0.8, the TBW is superior because the jury strut aids in satisfying the flutter constraint; Two-dimensional, steady, transonic aerodynamic analysis of the Boeing Airfoil J (BACJ) airfoil was performed for a range of thickness ratios, Mach numbers and lift coefficients. Reynolds-averaged Navier-Stokes (RANS) equations were solved to obtain the lift-curve slope, wave drag coefficient, the location of the center of pressure and to predict the separation at the trailing edge, which may lead to buffeting. One of the goals was to develop a database of lift-curve slope and the location of center of pressure, which could be used in a transonic aeroelastic analysis. Another goal was to compare the wave drag coefficients to those predicted by Lock’s fourth-power law and also to compare the transonic effects obtained from RANS simulations to those predicted by the Korn equations. A third goal was to develop a buffet boundary, which can be integrated into the MDO framework to prevent the optimized designs from probable buffeting; A state-space transonic aeroelastic analysis tool was developed, which can incorporate the nonlinear transonic effects in the unsteady aerodynamics but is yet computationally cheap when used within the VT MDO framework. The aeroelastic analysis uses Leishman- Beddoes (LB) indicial functions, which generated a state-space representation of the aeroelastic system. The indicial functions allow the incorporation of data for steady lift-curve slope and location of the center of pressure. Thus, the steady transonic effects are included, and the unsteady aerodynamic responses are a linearization about the steady results. The aeroelastic approach discretizes the wing into numerous strips, which results in a large eigenvalue problem as each strip has eight augmented aerodynamic states as per the LB theory. Thus, to reduce the computation expense, a reduced order model (ROM) was developed. The approach was validated using a few examples.

Kapania, Rakesh K.↗
NASA NTRS2019

Simulation and Testing of the Range of Motion of a Six Degree of Freedom Docking System

The soft capture system of the NASA Docking System (NDS) is a mechanism with six-degrees of freedom (6DOF). Although the nominal motion of the system is simple and largely in a single degree of freedom, complex movement is permissible within the requirements for docking. As such it is critical in the design, test, and verification of the docking system to fully understand the range of possible movement of the mechanism. This range of motion (ROM) must be large enough to accommodate all permitted docking sequences without internal collisions. This paper will discuss the methods used to perform these analysis for the NDS. Additionally, the testing sequences derived from this analysis will be presented, as illustrated in Figure 1. Finally, lessons learned from the analysis and test program will be discussed.

Docking System↗
NASA NTRSDate not supplied

Reduced-Order Aerodynamic Modeling Based on CFD Frequency Responses from Multisine Inputs

A system identification analysis was performed to determine a reduced-order model (ROM) of a computational fluid dynamics (CFD) solver in support of linear aeroservoelastic model development and feedback control design. The approach was applied to the FUN3D code for the half-span wind tunnel test article used in the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project. In a transonic flow condition, multiple inputs (11 structural mode displacements and 3 control surface deflections) were simultaneously excited with orthogonal phase-optimized multisines while multiple outputs (the corresponding 14 generalized aerodynamic forces) were recorded. From these recorded times series, the matrix of frequency responses was computed and subsequently fit using rational function approximations (RFAs). It was found that the entire (14 x 14) matrix of frequency responses could be determined from a single CFD run and that results generally followed trends predicted using other methods. Differences were attributed to the modeling fidelity and nonlinearities from structural mode and control surface interactions at higher reduced frequencies. More accurate fits of the RFAs to the frequency response data were obtained by making two CFD runs, one with only structural mode excitations and one with only control surface excitations, which reduced the degree of nonlinearity in the modeling data.

Aeroservoelasticity↗
NASA NTRS2018

Assessing the Altimetric Measurement from CYGNSS Data

The Cyclone Global Navigation Satellite System (CYGNSS) mission was designed to study hurricane intensification by measuring wind speeds in tropical cyclones. However, the delay-Doppler maps (DDM) that are produced can be used to estimate the sea surface height (SSH) at the specular reflection point on the ocean surface. Proofof-concept studies that DDMs are suitable to solve for SSH have been recently reported (Clarizia et al., 2016; Mashburn et al., 2018), based on data acquired by the demonstration satellite experiment Tech Demo Sat - 1 (TDS-1) carrying a GNSS-R receiver similar to the ones onboard CYGNSS. Although the precision of each 1sec averaged SSH is considerably lower than that of the existing satellite altimeters, by virtue of the dense coverage and frequent revisit time exhibited by the constellation of 8 microsats, the error may be smoothed down considerably by optimal interpolation (Li et al., 2016). Hence the CYGNSS dataset presents a potential opportunity to sample the tropical oceans, and investigate the sensitivity of the SSH measurements to mesoscale eddies. Our objective is to analyze the CYGNSS data and test a suite of retrieval algorithms, including that of Mashburn et al., 2018 to obtain SSH, to understand the error sources and possible corrections when available. Because of the limited antenna gain of the CYGNSS instrument, the power SNR for general wind conditions is expected to be too low to accurately track the reflection point contribution, resulting in altimetry errors of the order of several meters. Other significant error sources are the CYGNSS satellites orbit knowledge, the ionosphere, the troposphere, the mean sea surface and the tides; some of these errors can be reduced by using models. The corrected SSH data will be assimilated into the ROMS high-resolution ocean model to investigate their ability to reproduce mesoscale eddies in the tropical oceans.

Voronovich, Alexander↗
NASA NTRSDate not supplied

Upscaling of 500 °C Durable SiC JFET-R Integrated Circuits

At HiTEC2018, NASA Glenn Research Center reported the first demonstration of yearlong 500°C operation of ceramic-packaged “Generation 10” ~200-transistor integrated circuits (ICs) based on two-level interconnect silicon carbide (4H-SiC) junction field effect transistors and resistors (JFET-R). This HiTEC 2021submissionupdateson-going efforts at NASA Glenn spanning two subsequent prototype IC generations “11 and 12” to increase both complexity and durability of these ICs. Increased chip complexities of around 1000 transistors/chip for Gen. 11and near 3000 transistors/chip for Gen. 12 aremade possibleby reductions in minimum layout feature sizes (including resistorwidth shrinkage from 6 μm to 2μm) coupled with enlarged die size (from 3x3 mm to 5x5mm). Gen. 11 ICs electrically tested to date include an 8-bit delta-sigma analog to digital converter (ADC) as well as upscaled random access memory (RAM)and nearly 1 kbit read only memory (ROM). However, Gen. 11 prototype ICs exhibited significantly lower yield and durability than Gen. 10 ICs. Development of revised processing is being investigated towards mitigating these issues in subsequentGen. 12 fabrication runcurrentlyin progress.

Silicon Carbide↗
NASA NTRSDate not supplied

Upscaling of 500 °C Durable SiC JFET-R Integrated Circuits

At HiTEC 2018, NASA Glenn Research Center reported the first demonstration of yearlong 500 °C operation of ceramic-packaged “Generation 10” ~200-transistor integrated circuits (ICs) based on two-level interconnect silicon carbide (4H-SiC) junction field effect transistors and resistors (JFET-R). This HiTEC 2021 submission updates on-going efforts at NASA Glenn spanning two subsequent prototype IC generations “11 and 12” to increase both complexity and durability of these ICs. Increased chip complexities of around 1000 transistors/chip for Gen. 11 and near 3000 transistors/chip for Gen. 12 are made possible by reductions in minimum layout feature sizes (including resistor width shrinkage from 6 µm to 2 µm) coupled with enlarged die size (from 3 x 3 mm to 5 x 5 mm). Gen. 11 ICs electrically tested to date include an 8-bit delta-sigma analog to digital converter (ADC) as well as upscaled random access memory (RAM) and nearly 1 kbit read only memory (ROM). However, Gen. 11 prototype ICs exhibited significantly lower yield and durability than Gen. 10 ICs. Development of revised processing is being investigated towards mitigating these issues in subsequent Gen. 12 fabrication run currently in progress.

silicon carbide↗
NASA NTRSDate not supplied

Initial analysis of “stone” size Ryugu samples: current status

As a part of the initial analysis of the Ryugu samples, we perform a variety of analyses of millimeter-sized "stones". Our goals are to elucidate the entire formation process of C-type asteroid Ryugu from the viewpoint of petrology and mineralogy ande obtain necessary information by sample analysis, and then simulate the formation of Ryugu based on the evidencef obtained rom sample analysis. Eighteen stones (8 from Room A and 10 from Room C) were received from the ISAS curation facility on June 1, 2021, and brought into a fully nitrogen-displaced glove box at Tohoku University. At the same time, we also received the powder samples from Room A and Room C. To completely block the atmosphere from leaking into the container, all samples were put in the sample transport containers prepared by ISAS, transferred from the main chamber to the glovebox at ISAS, and then all containers were completely sealed in plastic bags with moisture and oxygen absorbers. No moisture or oxygen was detected when the bags were opened in the glove box at Tohoku University, so it was confirmed that there was no exposure to the atmosphere during transport. To date, a number of analyses have been carried out successfully and almost on schedule. The analysis started with the measurement of reflectance spectra, which are sensitive to atmospheric oxidation, hydroxylation, and adsorbed water. The visible, near-infrared, and mid-infrared reflectance spectra were measured while the samples were kept airtight. The spectra of powder samples and stone samples (as aggregates and as single stone) were successfully obtained. A major feature of the stone team's analysis is the use of synchrotron radiation facilities around the world. Since this analysis is non-destructive, stone samples whose reflectance spectra were measured were sent to KEK, SPring-8, ESRF (France), SOLEIL (France), DESY (Germany), and APS (USA). Using these synchrotron radiation facilities, high spatial resolution and sensitivity XRD, STXM, XANES, CT [1], IR-CT, FT-IR [2, 3], XRF, and Mössbauer analyses were performed. Most of the analyses were carried out under air-tight conditions on the stone samples and the particulates separated from the stone samples. These analyses allowed us to determine the three-dimensional distribution of minerals and elements, redox state, density and porosity of the stone samples. Furthermore, as a characteristic analysis of the stone team, light elemental analysis using negative Muon was performed at the MLF facility of J-PARC with an exceptionally long allocation of machine time. This is the only non-destructive method to measure the concentration of light elements in the whole (not the surface) of stone samples. Because the characteristic X-rays produced by muon irradiation are much higher in energy than the fluorescent X-rays produced by X-ray irradiation, there is little effect of self-absorption by the sample, and therefore, the concentration of light elements such as carbon, oxygen, and Na in the entire "stone" sample can be determined. Some stone samples are currently being measured for heat and strength physical properties in order to understand the physical properties of asteroid Ryugu. The data obtained from these measurements are useful for interpreting the remote-sensing data data taken from the surface layer of the asteroid Ryugu [4-7]. It is also important for understanding the behavior of the Ryugu material during impact events. The surfaces of many stone samples were observed by electron microscopy and other techniques, especially on natural “flat” surfaces formed on 5 stomes. As a result, characteristric mineral aggregates formed by the reactions with water and characteiristic impact features were observed on some of the samples. Based on the observations of surfaces and the synchrotron measurements of the whole stones, important objects such as characteristic structures and specific crystal aggregates for understanding the formation history of the asteroid were identified, and these parts were separated from the stone samples using an Xe beam (pFIB) and analyzed by various methods including transmission electron microscopy and synchrotron radiation analysis. Many stone samples, from which important objects have been separated, are embedded in epoxy resin and cut to produce many polished sections. Electron microscopy and spectroscopic measurements of the polished surfaces are being carried out to reveal the detailed mineralogical properties and elemental distribution inside the stone samples. In the fall, machine time for synchrotron radiation will begin, and we plan to analyze single crystals and characteristic objects separated from the stone samples.

Tomoki Nakamura↗
NASA NTRSDate not supplied

Flutter Prediction Report in Support of the High Angle Working Group at the Third Aeroelastic Prediction Workshop

This paper presents a summary of the computational flutter results associated with the AIAA third Aeroelastic Prediction Workshop (AePW-3) High Angle Working Group (HAWG). The computational results are compared against the experimental data collected during the Pitch and Plunge Apparatus (PAPA) Benchmark Supercritical Wing (BSCW) test campaign conducted in the Transonic Dynamics Tunnel (TDT) at NASA Langley Research Center thirty years ago. During that test several flutter points were identified at transonic conditions. One of these points, specifically near Mach 0.8 and 5° angle of attack, became a focal point of the computational challenge with in HAWG. Various fidelity time-domain, Reduced Order Model (ROM) and Linearized Frequency Domain (LFD) methods were used by seven participating teams. While there are encouraging trends in the computational results, the range of the predicted flutter dynamic pressure is still quite large due to the stall flutter mechanism. A description of each participating team’s software and methods is included.

Pawel Chwalowski↗
NASA NTRSDate not supplied

Artemis I Orion ESM Propulsion System Engine Performance

NASA's Orion spacecraft transports humans and cargo into cislunar space for the Artemis program. The European Service Module (ESM), supplied by ESA and its European industry partners, provides Orion with power and in-space propulsion. The Orion-ESM propulsion system is a bipropellant hypergolic propulsion system using monomethyl hydrazine (MMH) and nitrogen tetroxide (MON-3). Primary translational propulsion is provided by the Orbital Maneuvering System Engine(OMS-E), with backup translational propulsion provided by eight Auxiliary thrusters (AUX). Attitude control and small translational maneuvers are provided by twenty four Reaction Control System (RCS) engines. The 2022 Artemis I mission was the first integrated flight test of the Orion-ESM spacecraft and its propulsion system. The OMS-E used on Artemis I was a refurbished Space Shuttle OMS-E that previously flew on nineteen missions ranging f rom STS-41G in 1984 to STS-112 in 2002. The Auxiliary engines are modified Aerojet Rocketdyne R4D-11 engines produced specifically for the Orion program. The RCS engines are Ariane Group engines originally used for the Automated Transfer Vehicle (ATV) program. This paper will discuss the unique operational requirements for each engine on Orion and the development and qualification effort sat both the engine and system-level that were completed to enable a successful Artemis I mission. Next the paper will evaluate the in-f light performance of the engines during the Artemis I mission showing nominal performance as expected. Additionally, comparisons to models will be presented showing very good correlation. Finally, the paper will address the plan for the engines on future Orion missions and the evolution of the system operation.

liquid propulsion systems↗
NASA NTRSDate not supplied

Hierarchical Multiscale Process Modeling of A Textile Composite Y-Joint for the Aurora D8 Aircraft

Woven polymer matrix composites (PMCs) are widely used in aerospace applications for their favorable specific properties. However, the behavior of the inter- and intra-tow matrix during manufacturing of woven PMCs is difficult to isolate experimentally due to geometric and processing complexities. Classical closed-form homogenization approaches allow for composite thermos-chemo-mechanical properties to be characterized at any fiber volume fraction. In this work, virtual curing is applied to the inter- and intra-tow matrix materials of a plain weave repeating unit cell (RUC). Thermo-chemo-mechanical property evolution within the tows is calculated using the Concentric Cylinder Model (CCM) and the Rule of Mixtures (ROM). Curing is implemented through user-written subroutines within the commercial finite element method software Abaqus. Virtual curing results are compared with those from a linear-elastic thermal cool down simulation in Abaqus. Results indicate that tow property evolution during curing has a non-negligible effect on the final stress state.

curing↗