Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Radiochronological Age of a Uranium Metal Sample from an Abandoned Facility

A piece of scrap uranium metal bar buried in the dirt floor of an old, abandoned metal rolling mill was analyzed using multi-collector inductively coupled plasma mass spectroscopy (MC-ICP-MS). The mill rolled uranium rods in the 1940s and 1950s. Samples of the contaminated dirt in which the bar was buried were also analyzed. The isotopic composition of uranium in the bar and dirt samples were both the same as natural uranium, though a few samples of dirt also contained recycled uranium; likely a result of contamination with other material rolled at the mill. The time elapsed since the uranium metal bar was last purified can be determined by the in-growth of the isotope {sup 230}Th from the decay of {sup 234}U, assuming that only uranium isotopes were present in the bar after purification. The age of the metal bar was determined to be 61 years at the time of this analysis and corresponds to a purification date of July 1950 {+-} 1.5 years.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Deformability of Oxide Inclusions in Tire Cord Steels

The deformation of oxide inclusions in tire cord steels during hot rolling was analyzed, and the factors influencing their deformability at high and low temperatures were evaluated and discussed. The aspect ratio of oxide inclusions decreased with the increasing reduction ratio of the steel during hot rolling owing to the fracture of the inclusions. The aspect ratio obtained after the first hot-rolling process was used to characterize the high-temperature deformability of the inclusions. The deformation first increased and then decreased with the increasing (MgO + Al{sub 2}O{sub 3})/(SiO{sub 2} + MnO) ratio of the inclusions. It also increased with the decreasing melting temperatures of the inclusions. Young’s modulus was used to evaluate the low-temperature deformability of the inclusions. An empirical formula was fitted to calculate the Young’s moduli of the oxides using the mean atomic volume. The moduli values of the inclusions causing wire fracture were significantly greater than the average. To reduce fracture in tire cord steel wires during cold drawing, it is proposed that inclusions be controlled to those with high SiO{sub 2} content and extremely low Al{sub 2}O{sub 3} content. This proposal is based on the hypothesis that the deformabilities of oxides during cold drawing are inversely proportional to their Young’s moduli. The future study thus proposed includes an experimental confirmation for the abovementioned predictions.

36 MATERIALS SCIENCE↗

An Integrated Study on the Evolution of Inclusions in EH36 Shipbuilding Steel with Mg Addition: From Casting to Welding

Inclusion evolution behaviors, in terms of composition, size, and number density, and associated influence on the microstructures of the as-cast slabs, rolled plates, and simulated welded samples of plain EH36 and EH36-Mg shipbuilding steels have been systematically investigated. The results indicate that the inclusions in the as-cast plain EH36 are almost Al-Ca-S-O-(Mn) complex oxides with sizes ranging from 1.0 to 2.0 μm. After Mg addition, a large amount of individually fine MnS precipitates and Mg-containing Ti-Al-Mg-O-(Mn-S) complex inclusions are generated, which significantly refine the microstructure and are conducive to the nucleation of acicular ferrite in the rolled and welded sample. Moreover, after rolling and welding thermal simulation, the number of individual MnS decreases gradually due to its precipitation on the surface of Ti-Al-Mg-O oxides.

36 MATERIALS SCIENCE↗

Feasibility Study of Continuous Casting of Steel Billets in Twin-Belt Caster

Integrated casting and rolling in a series production line is well established for the non-ferrous metals through the use of twin-belt casting technology. However, this twin-belt casting with high mass flow is not yet commercialized in the continuous production of steel alloys. A novel steel casting for the in-line rolling (named LUUP method) is presented and one main focus of this work is to design a casting machine: twin-belt caster. Influence of mass flow rate and dimensional ratio on the solidification, compensation, and total process length is addressed. A gap-dependent belt and dam block side heat transfer is modeled. The admissible casting speed due to the limitations of caster length and shell strength is addressed. The total process length only depends on the mass flow rate. A 2D traveling slice numerical model is presented with realistic boundary conditions for the entire process starting from the meniscus to roll mill entry.

36 MATERIALS SCIENCE↗

Characterization of Microstructure, Mechanical Properties and Formability of Cryorolled AA5083 Alloy Sheets

In this work, microstructure, mechanical properties and formability of cryorolled and annealed AA5083 alloy sheets have been characterized and a comparison has been made with cold rolled and annealed sheets. Five-millimeter-thick sheets of this alloy were cryorolled in multiple passes to a final thickness of 1 mm (80% reduction with a true strain of 1.6). Effect of annealing time and temperature on hardness has been studied, and it has been found that a short annealing at 275 °C for 15 min after cryorolling would yield a good combination of strength and ductility. Microstructural investigations showed that the cryorolled and short annealed samples possess bimodal grain structure which is responsible for better mechanical properties than cold rolled sheets. From the experimentally determined forming limit diagrams, the limit strains of cryorolled sheets have been found to be almost equal to conventional cold rolled and annealed sheets in all modes of deformation. No major differences have been found in strain distribution also. This work clearly demonstrates that cryorolling of AA5083 alloy sheets followed by a short annealing with bimodal grain structure can be used for sheet metal forming applications with higher strength and toughness than conventional sheets without any reduction in formability.

36 MATERIALS SCIENCE↗

Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite–austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

36 MATERIALS SCIENCE↗

Improved Mechanical Properties of Structural Steel via Developing Bimodal Grain Size Distribution and Intercritical Heat Treatment

Intercritical annealing and tempering heat treatment combined with cold rolling were applied for improvement of tensile properties and strain-hardening rate of structural steel. Coarse dual-phase (DP) microstructure was processed via intercritical heat treatment of the ferritic–pearlitic sheet, which resulted in the increase in tensile strength and disappearance of the yield point phenomenon. However, the tensile toughness was not effectively enhanced, which is indicative of unaltered strength–ductility trade-off. A bimodal-sized ferrite structure was obtained by cold rolling of the DP microstructure followed by subcritical annealing (tempering), where its characteristic features are high yield stress and relatively poor work-hardening response. Afterward, the intercritical annealing of the bimodal steel resulted in the development of fine DP steel with excellent work-hardening capacity and pronounced enhancement of tensile toughness. Conclusively, this work demonstrates the possibility of controlling the tensile properties and work-hardening behavior of conventional steels by simple heat treatment routes with the aid of cold rolling.

36 MATERIALS SCIENCE↗

Stress-induced α″ phase in a beta Ti–19Nb–1.5Mo–4Zr–8Sn alloy

Highlights: • Morphologies/distributions of α″ produced by stretching/rolling are similar. • Under small deformation, α″ martensite consists of parallel lamellar structures. • Under larger deformations, martensite has ladder-like pattern and parallel ellipsoids. • With the increase of deformation hardness decreases firstly and then increases. - Abstract: The morphological evolution of the stress-induced α″ martensite with increases in the stretching and rolling deformation degrees as well as the related orientation relationship were investigated in a β titanium alloy (Ti–19Nb–1.5Mo–4Zr–8Sn)·For a stretching deformation of 1%, the α″ martensite exhibited a packet morphology consisting of parallel lamellar structures. On the other hand, in the 2%-rolled sample, the α″ martensite exhibited a long lath-like distribution, which was accompanied by a few small pieces. With an increase in the deformation degree, the α″ martensite gradually exhibited a ladder-like structure consisting of long and short α″ laths or ellipsoids. The existence of these self-accommodating martensitic variants decreased the elastic energy. The parallel α″ laths present within a single packet were found to have the same orientation. The interface between the α″ and β phases was coherent, and their lattice constant relationships were identified as √2a{sub β}≈b{sub α″}≈c{sub α″} and a{sub β} ≈ a{sub α″}. Further, with the increase in the deformation degree, the hardness of the alloy first decreased and then increased; this was the case both the stretched as well as the rolled samples.

36 MATERIALS SCIENCE↗

In situ NiTi/Nb(Ti) composite

Graphical abstract: - Highlights: • In situ NiTi/Nb(Ti) composites were fabricated. • The transformation temperature was affected by the mixing Ti:Ni atomic ratios. • The NiTi component became micron-scale lamella after forging and rolling. • The composite exhibited high strength and high damping capacity. - Abstract: This paper reports on the creation of a series of in situ NiTi/Nb(Ti) composites with controllable transformation temperatures based on the pseudo-binary hypereutectic transformation of NiTi–Nb system. The composite constituent morphology was controlled by forging and rolling. It is found that the thickness of the NiTi lamella in the composite reached micron level after the hot-forging and cold-rolling. The NiTi/Nb(Ti) composite exhibited high damping capacity as well as high yield strength.

36 MATERIALS SCIENCE↗

Origin of texture development in orthorhombic uranium

We study texture evolution of alpha-uranium (α-U) during plane strain compression and uniaxial compression to high strains at different temperatures. We combine a multiscale polycrystal constitutive model and detailed analysis of texture data to uncover the slip and twinning modes responsible for the formation of individual texture components. The analysis indicates that during plane strain compression, floor slip (001)[100] results in the formation of two pronounced {001}{001} texture peaks tilted 10–15° away from the normal toward the rolling direction. During both high-temperature (573 K) through-thickness compression and plane strain compression, the active slip modes are floor slip (001)[100] and chimney slip 1/2{110} <11¯0> with slightly different ratios. {130} <31¯0> deformation twinning is profuse during rolling and in-plane compression and decreases with increasing temperature, but is not as active for through-thickness compression. Lastly, we comment on some similarities between rolling textures of α-U, which has a c/a ratio of 1.734, and those that develop in hexagonal close packed metals with similarly high c/a ratios like Zn (1.856) and Cd (1.885) and are dominated by basal slip.

36 MATERIALS SCIENCE↗

Oil miscible phosphonium-phosphate ionic liquid as novel antiwear and antipitting additive for low-viscosity rear axle lubricants

Here we explored the feasibility of using a phosphonium phosphate ionic liquid as a candidate anti-wear and anti-pitting additive for rear axle lubricant. This particular IL was first added to a VHVI8 base oil at 2–3% concentration and demonstrated effective surface protection for wear and micro-cracking under rolling-sliding contacts. The promising results directed to a step further to produce a series of IL-containing low-viscosity (about a half of SAE 75W-90) fully formulated gear oils. Selected IL-containing experimental oils showed superior mitigation of rolling contact fatigue to a commercial SAE 75W-90 gear oil in bench-scale rolling-sliding tests. Full-scale hub dynamometer tests were then conducted and demonstrated more than 3% power output and torque generation for an IL-containing low-viscosity gear oil benchmarked against commercial baselines.

36 MATERIALS SCIENCE↗

Mechanical Separation of Metallic Copper from Polymer-Insulated Copper Wire

It is very important to recycling of polymer-insulated copper wire to remove copper from the wire without any contamination. A rolling machine and a blender were used to separate and recover the copper wires from a polymer coated cable. In the experiment using a rolling machine, the recovery of copper was improved by an increase in the number of rolling times and by lowering the cable temperature. All of the copper was recovered from a cable of 115 K in temperature. In the other experiment using a blender, the weight of the recovery of copper was increased by shortening the cable length and by increasing the rotary speed of the blender and the treating time. All the copper in a cut cable of 3mm long was recovered from a cable.

36 MATERIALS SCIENCE↗

Experimental investigation of anisotropy evolution of AZ31 magnesium alloy sheets under tensile loading

Increasing demand for lighter final products has created new opportunities for the application of new light weight materials. Due to high strength to density ratio and good magnetic resistance properties, magnesium alloys are good candidates to replace steel and aluminum for same application. However, limited numbers of active slip deformation mechanisms, result in a decreased formability at room temperature. Furthermore, wrought magnesium alloys have an initial crystallographic texture, remained from the prior rolling operations, which makes them highly anisotropic. In this paper, tensile tests are performed at room temperature and 200 deg. C at different strain rates and orientations relative to the rolling direction, including rolling, 30 deg., 45 deg., 60 deg. and transverse orientation. The strain rates adopted for these experiments varied from 0.001 to 1.0. The testing results show the effect of temperature on the strain rate sensitivity of AZ31 sheets. The extent of deformation is continuously recorded using two separate high temperature extensometers. The results of testing show an increase in the r-values with the plastic deformation. The strain rate sensitivity of AZ31 increased as the temperature was elevated. At higher strain rates the measured r-values are larger and the slope of its evolution with the plastic strain is steeper.

36 MATERIALS SCIENCE↗

A Novel Method of Modeling the Deformation Resistance for Clad Sheet

Because of the excellent thermal conductivity, the clad sheet (3003/4004/3003) of aluminum alloy is extensively used in various heat exchangers, such as radiator, motorcar air conditioning, evaporator, and so on. The deformation resistance model plays an important role in designing the process parameters of hot continuous rolling. However, the complex behaviors of the plastic deformation of the clad sheet make the modeling very difficult. In this work, a novel method for modeling the deformation resistance of clad sheet was proposed by combining the finite element analysis with experiments. The deformation resistance model of aluminum 3003 and 4004 was proposed through hot compression test on the Gleeble-1500 thermo-simulation machine. And the deformation resistance model of clad sheet was proposed through finite element analysis using DEFORM-2D software. The relationship between cladding ratio and the deformation resistance was discussed in detail. The results of hot compression simulation demonstrate that the cladding ratio has great effects on the resistance of the clad sheet. Taking the cladding ratio into consideration, the mathematical model of the deformation resistance for clad sheet has been proved to have perfect forecasting precision of different cladding ratio. Therefore, the presented model can be used to predict the rolling force of clad sheet during the hot continuous rolling process.

36 MATERIALS SCIENCE↗

ISS-flation

Inflation may occur while rolling into the metastable supersymmetry-breaking vacuum of massive supersymmetric QCD. We explore the range of parameters in which slow-roll inflation and long-lived metastable supersymmetry breaking may be simultaneously realized. The end of slow-roll inflation in this context coincides with the spontaneous breaking of a global symmetry, which may give rise to significant curvature perturbations via inhomogeneous preheating. Such spontaneous symmetry breaking at the end of inflation may give rise to observable non-gaussianities, distinguishing this scenario from more conventional models of supersymmetric hybrid inflation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Processing and mechanical properties - 2016-0032

Hot extrusion is used within the forming route of cladding tubes to deform the billets into tube hollows, which are then cold-rolled to produce the final tubes with the suitable properties for in-reactor use. The hot extrusion goals are to give the appropriate geometry for cold pilgering (diameter and wall thickness suitable for cold-rolling mills, good concentricity) without surface defects and microstructural heterogeneities, which are detrimental for subsequent rolling. To ensure a good quality of the tube hollows, extrusion parameters (e.g., temperature of the billet, ram speed, extrusion ratio, lubrication) and extrusion tools have to be chosen as a function of the press capacity and mechanical and microstructural properties of the extruded alloy. For this purpose, finite-element and analytical models are used in addition to experimental tests. These models, particularly the former, can take into account the thermomechanical coupling that occurs in the tube and the tools during extrusion and provides a good prediction of the extrusion pressure and thermomechanical history of the extruded product. Together with a microstructural evolution model identified with small-scale extrusion tests, torsion tests, and heat treatments, this last result can also be used to calculate the fragmentation of the microstructure in the die and the meta-dynamic recrystallization after extrusion. Once validated against experimental data, numerical models were used to better understand and master the extrusion loads, the microstructure evolutions at the front end of the extruded tubes, and the temperature and stresses applied to the tools. (authors)

36 MATERIALS SCIENCE↗

Characterization of Tubing from Advanced ODS alloy (FCRD-NFA1)

Fabrication methods are being developed and tested for producing fuel clad tubing of the advanced ODS 14YWT and FCRD-NFA1 ferritic alloys. Three fabrication methods were based on plastically deforming a machined thick-wall tube sample of the ODS alloys by pilgering, hydrostatic extrusion or drawing to decrease the outer diameter and wall thickness and increase the length of the final tube. The fourth fabrication method consisted of the additive manufacturing approach involving solid-state spray deposition (SSSD) of ball milled and annealed powder of 14YWT for producing thin-wall tubes. Of the four fabrication methods, two methods were successful at producing tubing for further characterization: production of tubing by high-velocity oxy-fuel spray forming and production of tubing using high-temperature hydrostatic extrusion. The characterization described shows through neutron diffraction the texture produced during extrusion while maintaining the beneficial oxide dispersion. In this research, the parameters for innovative thermal spray deposition and hot extrusion processing methods have been developed to produce the final nanostructured ferritic alloy (NFA) tubes having approximately 0.5 mm wall thickness. Effect of different processing routes on texture and grain boundary characteristics has been investigated. It was found that hydrostatic extrusion results in combination of plane strain and shear deformations which generate rolling textures of α- and γ-fibers on {001}<110> and {111}<110> together with a shear texture of ζ-fiber on {011}<211> and {011}<011>. On the other hand, multi-step plane strain deformation in cross directions leads to a strong rolling textures of θ- and ε-fiber on {001}<110> together with weak γ-fiber on {111}<112>. Even though the amount of the equivalent strain is similar, shear deformation leads to much lower texture indexes compared to the plane strain deformations. Moreover, while 50% of hot rolling brings about a large number of high-angle grain boundaries (HAB), 44% of shear deformation results in large amount of low-angle boundaries (LAB) showing the incomplete recrystallization.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Non-destructive Quantitative Phase Analysis and Microstructural Characterization of Zirconium Coated U-10Mo Fuel Foils via Neutron Diffraction

This report uses neutron diffraction to investigate the crystal phase composition of uranium-molybdenum alloy foils (U-10Mo) for the CONVERT MP-1 Reactor Conversion Project, and determines the effect on alpha-uranium contamination following the deposition of a Zr metal diffusion layer by various methods: plasma spray deposition of Zr powders at LANL and hot co-rolling with Zr foils at BWXT. In summary, there is minimal decomposition of the gamma phase U-10Mo foil to alpha phase contamination following both plasma spraying and hot co-rolling. The average unit cell volume, i.e. lattice spacing, of the Zr layer can be mathematically extracted from the diffraction data; co-rolled Zr matches well with literature values of bulk Zr, while plasma sprayed Zr shows a slight increase in the lattice spacing, indicative of interstitial oxygen in the lattice. Neutron diffraction is a beneficial alternative to conventional methods of phase composition, i.e. x ray diffraction (XRD) and destructive metallography. XRD has minimal penetration depth in high atomic number materials, particularly uranium, and can only probe the first few microns of the fuel plate; neutrons pass completely through the foil, allowing for bulk analysis of the foil composition and no issues with addition of cladding layers, as in the final, aluminum-clad reactor fuel plates. Destructive metallography requires skilled technicians, cutting of the foil into small sections, hazardous etching conditions, long polishing and microscopy times, etc.; the neutron diffraction system has an automated sample loader and can fit larger foils, so there is minimal analysis preparation; the total spectrum acquisition time is ~ 1 hour per sample. The neutron diffraction results are limited by spectra refinement/calculation times and the availability of the neutron beam source. In the case of LANSCE at Los Alamos, the beam operates ~50% of the year. Following the lessons learned from these preliminary results, optimizations to the process and analysis can be made, and neutron diffraction can become a viable and efficient technique for gamma/alpha phase composition determination for nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗