Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Observing System Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Influence of head orientation on visually induced pitch and roll sensation

Observers viewing rotating scenes in their periphery frequently experience self-motion in the opposite direction. A full field flight simulator projection system was used to investigate the sensations resulting from pitch, roll, and yaw stimuli at various head orientations. Steady yaw rate (circularvection) and development of a constant roll tilt angle, for the head erect and constant velocity yaw and roll stimuli, confirmed previous reports. Pitch stimuli also were found to produce a sensation of tilting to a steady pitch angle, which was much stronger for pitch forward than backward. Pitch and roll effects were strongly dependent on head position, increasing for the head rolled 90 deg to the side or inverted, and decreasing for the head pitched 25 deg forward. These results support a hypothesis that visually induced tilt is limited by conflict with otolith information.

Young, L. R.↗
NASA NTRS1975

Thermal diffusivity measurements of particulates using the differentiated line source

A method is described in which thermal diffusivity measurements can be made on particulate materials using the identical instrumentation as described in previous papers for measuring thermal conductivity. The measurements for the two properties can be made simultaneously, thus eliminating the changes in conditions when they are made separately. This system has particular application for studies of simulated lunar, planetary, or asteroidal surfaces in which laboratory measurements can be correlated with astronomical observations of thermal inertia. A representative set of data is shown which gives thermal diffusivity and thermal conductivity measurements on a particulate basalt in which the values for each temperature were taken simultaneously. A value for specific heat is calculated for measurements taken at each temperature.

West, E. A.↗
NASA NTRS1989

Solution of the hydrodynamic device model using high-order non-oscillatory shock capturing algorithms

A micron n+ - n - n+ silicon diode is simulated via the hydrodynamic model for carrier transport. The numerical algorithms employed are for the non-steady case, and a limiting process is used to reach steady state. The simulation employs shock capturing algorithms, and indeed shocks, or very rapid transition regimes, are observed in the transient case for the coupled system, consisting of the potential equation and the conservation equations describing charge, momentum, and energy transfer for the electron carriers. These algorithms, termed essentially non-oscillatory, were successfully applied in other contexts to model the flow in gas dynamics, magnetohydrodynamics, and other physical situations involving the conservation laws in fluid mechanics. The method here is first order in time, but the use of small time steps allows for good accuracy. Runge-Kutta methods allow one to achieve higher accuracy in time if desired. The spatial accuracy is of high order in regions of smoothness.

Fatemi, Emad↗
NASA NTRS1988

In-flight inertial guidance alignment

This work reports on an extension of a recent work by Goshen-Meskin and Bar-Itzhack (1988). That work dealt with the observability analysis of inertial-navigation systems during in-flight alignment. The work was confined to the analysis of altitude damped systems; hence, the error model considered was a two-channel model. The present work deals with an undamped three-channel error model. An analysis similar to the previous one is carried out. It is shown that it is possible to fully observe, and thus estimate, all the states of the system. This is in contrast to the previous two-channel system, in which it is impossible to fully observe and estimate all the states of the system. The conclusions of the analysis presented in this paper are verified through covariance simulation which yields identical results.

Bar-Itzhack, I. Y.↗
NASA NTRS1991

Climate dynamics experiments using a GCM simulations

The study of surface-atmosphere interactions has begun with studies of the effect of altering the ocean and land boundaries. A ten year simulation of global climate using observed sea surface temperature anomalies has begun using the NCAR Community Climate Model (CCM1). The results for low resolution (R15) were computed for the first 8 years of the simulation and compared with the observed surface temperatures and the MSU (Microwave Sounding Unit) observations of tropospheric temperature. A simulation at higher resolution (T42) was done to ascertain the effect of interactive soil hydrology on the system response to an El Nino sea surface temperature perturbation. Initial analysis of this simulations was completed.

Fitzjarrald, Dan↗
NASA NTRS1991

Solution of the hydrodynamic device model using high-order non-oscillatory shock capturing algorithms

A micron n+ - n - n+ silicon diode is simulated via the hydrodynamic model for carrier transport. The numerical algorithms employed are for the non-steady case, and a limiting process is used to reach steady state. The simulation employs shock capturing algorithms, and indeed shocks, or very rapid transition regimes, are observed in the transient case for the coupled system, consisting of the potential equation and the conservation equations describing charge, momentum, and energy transfer for the electron carriers. These algorithms, termed essentially nonoscillatory, were successfully applied in other contexts to model the flow in gas dynamics, magnetohydrodynamics, and other physical situations involving the conservation laws in fluid mechanics. The method here is first order in time, but the use of small time steps allows for good accuracy. Runge-Kutta methods allow one to achieve higher accuracy in time if desired. The spatial accuracy is of high order in regions of smoothness.

Fatemi, Emad↗
NASA NTRS1993

Stellar Photometry Software

We describe the Stellar Photometry Software (SPS), which combines in a single program procedures for locating stars, computing a mean stellar point-spread function (PSF), and performing aperture and/or multiple PSF-fitting photometry, along with related bookkeeping functions. The software can be run either interactively or in batch mode on computers using the UNIX operating system. The performance of SPS is compared to that of the photometry programs DoPHOT and IRAF/DAOPHOT, using both real and simulated CCD observations. A direct comparison of the instrumental magnitudes shows that all three programs produce comparable results.

Janes, Kenneth A.↗
NASA NTRS1997

Nucleation and Convection Effects in Protein Crystal Growth

Work during the second year under this grant (NAG8-1161) resulted in several major achievements. We have characterized protein impurities as well as microheterogeneities in the proteins hen egg white lysozyme and horse spleen apoferritin, and demonstrated the effects of these impurities on nucleation and crystallization. In particular, the purification of apoferritin resulted in crystals with an X-ray diffraction resolution of better than 1.8 A, i.e. a 1 A improvement over earlier work on the cubic form. Furthermore, we have shown, in association with studies of liquid-liquid phase separation, that depending on the growth conditions, lysozyme can produce all growth morphologies that have been observed with other proteins. Finally, in connection with our experimental and simulation work on growth step bunching, we have developed a system-dependent criterion for advantages and disadvantages of crystallization from solution under reduced gravity. In the following, these efforts are described in some detail.

Rosenberger, Franz↗
NASA NTRS2008

Effects of Varying Surface Inclines and Suit Pressure: Implications on Space Suit Design

Suited human performance studies in reduced gravity environments to date include limited observations from Apollo Lunar surface Extravehicular Activities (EVA) and from previous studies conducted in partial gravity simulation environments. The Constellation Program EVA Systems Project office has initiated tests to develop design requirements for the next generation Lunar EVA suit. Theses studies were conducted in the Space Vehicle Mock-Up Facility (SVMF) at Johnson Space Center from which the results provided recommendations for suit weight, mass, center of gravity, pressure, and suit kinematic constraints that optimize human performance in partial gravity environments.

Clowers, Kurt↗
NASA NTRS2007

Preliminary Evaluation of GEOS-5 Aerosol and CO Distributions Forecast During TC4

The NASA Tropical Composition, Cloud, and Climate Coupling (TC4) Mission was based out San Jose, Costa Rica during July and August 2007. During TC4 the NASA Global Modeling and Assimilation Office (GMAO) ran twice-daily 0.5 x 0.666 global 5-day forecasts of the Goddard Earth Observing System atmospheric general circulation model and data assimilation system (GEOS-5). This implementation of GEOS-5 contained an aerosol and carbon monoxide (CO) model to provide online forecast tropospheric distributions of dust, sea salt, sulfate, and carbonaceous aerosols and CO for both the planning of flights and for science. Here we provide a description of the aerosol and CO modeling system and give a preliminary evaluation of forecast tracer distributions. Our comparisons to satellite observations of aerosol and CO show qualitatively similar simulated distributions of tracers to those observed. During TC4 copious amounts of dust were observed in the Caribbean. The model generally reproduced the observations of the timing of dust events and the vertical structure in the lower atmosphere. However, the model simulations had too much aerosol at high altitudes relative to airborne Cloud Physics Lidar observations. The results were similar for biomass burning aerosol and CO tracers, where the model showed higher simulated concentrations of these tracers at aircraft flight altitude than observations.

Colarco, Peter R.↗
NASA NTRS2011

Response of the Antarctic Stratosphere to Warm Pool EI Nino Events in the GEOS CCM

A new type of EI Nino event has been identified in the last decade. During "warm pool" EI Nino (WPEN) events, sea surface temperatures (SSTs) in the central equatorial Pacific are warmer than average. The EI Nino signal propagates poleward and upward as large-scale atmospheric waves, causing unusual weather patterns and warming the polar stratosphere. In austral summer, observations show that the Antarctic lower stratosphere is several degrees (K) warmer during WPEN events than during the neutral phase of EI Nino/Southern Oscillation (ENSO). Furthermore, the stratospheric response to WPEN events depends of the direction of tropical stratospheric winds: the Antarctic warming is largest when WPEN events are coincident with westward winds in the tropical lower and middle stratosphere i.e., the westward phase of the quasi-biennial oscillation (QBO). Westward winds are associated with enhanced convection in the subtropics, and with increased poleward wave activity. In this paper, a new formulation of the Goddard Earth Observing System Chemistry-Climate Model, Version 2 (GEOS V2 CCM) is used to substantiate the observed stratospheric response to WPEN events. One simulation is driven by SSTs typical of a WPEN event, while another simulation is driven by ENSO neutral SSTs; both represent a present-day climate. Differences between the two simulations can be directly attributed to the anomalous WPEN SSTs. During WPEN events, relative to ENSO neutral, the model simulates the observed increase in poleward planetary wave activity in the South Pacific during austral spring, as well as the relative warming of the Antarctic lower stratosphere in austral summer. However, the modeled response to WPEN does not depend on the phase of the QBO. The modeled tropical wind oscillation does not extend far enough into the lower stratosphere and upper troposphere, likely explaining the model's insensitivity to the phase of the QBO during WPEN events.

Hurwitz, Margaret M.↗
NASA NTRS2011

Fused Reality for Enhanced Flight Test Capabilities

The feasibility of using Fused Reality-based simulation technology to enhance flight test capabilities has been investigated. In terms of relevancy to piloted evaluation, there remains no substitute for actual flight tests, even when considering the fidelity and effectiveness of modern ground-based simulators. In addition to real-world cueing (vestibular, visual, aural, environmental, etc.), flight tests provide subtle but key intangibles that cannot be duplicated in a ground-based simulator. There is, however, a cost to be paid for the benefits of flight in terms of budget, mission complexity, and safety, including the need for ground and control-room personnel, additional aircraft, etc. A Fused Reality(tm) (FR) Flight system was developed that allows a virtual environment to be integrated with the test aircraft so that tasks such as aerial refueling, formation flying, or approach and landing can be accomplished without additional aircraft resources or the risk of operating in close proximity to the ground or other aircraft. Furthermore, the dynamic motions of the simulated objects can be directly correlated with the responses of the test aircraft. The FR Flight system will allow real-time observation of, and manual interaction with, the cockpit environment that serves as a frame for the virtual out-the-window scene.

Bachelder, Ed↗
NASA NTRS2011

Physical Validation of GPM Retrieval Algorithms Over Land: An Overview of the Mid-Latitude Continental Convective Clouds Experiment (MC3E)

The joint NASA Global Precipitation Measurement (GPM) -- DOE Atmospheric Radiation Measurement (ARM) Midlatitude Continental Convective Clouds Experiment (MC3E) was conducted from April 22-June 6, 2011, centered on the DOE-ARM Southern Great Plains Central Facility site in northern Oklahoma. GPM field campaign objectives focused on the collection of airborne and ground-based measurements of warm-season continental precipitation processes to support refinement of GPM retrieval algorithm physics over land, and to improve the fidelity of coupled cloud resolving and land-surface satellite simulator models. DOE ARM objectives were synergistically focused on relating observations of cloud microphysics and the surrounding environment to feedbacks on convective system dynamics, an effort driven by the need to better represent those interactions in numerical modeling frameworks. More specific topics addressed by MC3E include ice processes and ice characteristics as coupled to precipitation at the surface and radiometer signals measured in space, the correlation properties of rainfall and drop size distributions and impacts on dual-frequency radar retrieval algorithms, the transition of cloud water to rain water (e.g., autoconversion processes) and the vertical distribution of cloud water in precipitating clouds, and vertical draft structure statistics in cumulus convection. The MC3E observational strategy relied on NASA ER-2 high-altitude airborne multi-frequency radar (HIWRAP Ka-Ku band) and radiometer (AMPR, CoSMIR; 10-183 GHz) sampling (a GPM "proxy") over an atmospheric column being simultaneously profiled in situ by the University of North Dakota Citation microphysics aircraft, an array of ground-based multi-frequency scanning polarimetric radars (DOE Ka-W, X and C-band; NASA D3R Ka-Ku and NPOL S-bands) and wind-profilers (S/UHF bands), supported by a dense network of over 20 disdrometers and rain gauges, all nested in the coverage of a six-station mesoscale rawinsonde network. As an exploratory effort to examine land-surface emissivity impacts on retrieval algorithms, and to demonstrate airborne soil moisture retrieval capabilities, the University of Tennessee Space Institute Piper aircraft carrying the MAPIR L-band radiometer was also flown during the latter half of the experiment in coordination with the ER-2. The observational strategy provided a means to sample the atmospheric column in a redundant framework that enables inter-calibration and constraint of measured and retrieved precipitation characteristics such as particle size distributions, or water contents- all within the umbrella of "proxy" satellite measurements (i.e., the ER-2). Complimenting the precipitation sampling framework, frequent and coincident launches of atmospheric soundings (e.g., 4-8/day) then provided a much larger mesoscale view of the thermodynamic and winds environment, a data set useful for initializing cloud models. The datasets collected represent a variety cloud and precipitation types including isolated cumulus clouds, severe thunderstorms, mesoscale convective systems, and widespread regions of light to moderate stratiform precipitation. We will present the MC3E experiment design, an overview of operations, and a summary of preliminary results.

Petersen, Walter A.↗
NASA NTRS2016

Functional Fault Model Development Process to Support Design Analysis and Operational Assessment

A functional fault model (FFM) is an abstract representation of the failure space of a given system. As such, it simulates the propagation of failure effects along paths between the origin of the system failure modes and points within the system capable of observing the failure effects. As a result, FFMs may be used to diagnose the presence of failures in the modeled system. FFMs necessarily contain a significant amount of information about the design, operations, and failure modes and effects. One of the important benefits of FFMs is that they may be qualitative, rather than quantitative and, as a result, may be implemented early in the design process when there is more potential to positively impact the system design. FFMs may therefore be developed and matured throughout the monitored system's design process and may subsequently be used to provide real-time diagnostic assessments that support system operations. This paper provides an overview of a generalized NASA process that is being used to develop and apply FFMs. FFM technology has been evolving for more than 25 years. The FFM development process presented in this paper was refined during NASA's Ares I, Space Launch System, and Ground Systems Development and Operations programs (i.e., from about 2007 to the present). Process refinement took place as new modeling, analysis, and verification tools were created to enhance FFM capabilities. In this paper, standard elements of a model development process (i.e., knowledge acquisition, conceptual design, implementation & verification, and application) are described within the context of FFMs. Further, newer tools and analytical capabilities that may benefit the broader systems engineering process are identified and briefly described. The discussion is intended as a high-level guide for future FFM modelers.

Verification↗
NASA NTRS2017

New High-Altitude GPS Navigation Results from the Magnetospheric Multiscale Spacecraft and Simulations at Lunar Distances

As reported in a companion work, in its first phase, NASA's 2015 highly elliptic Magnetospheric Multiscale (MMS) mission set a record for the highest altitude operational use of on-board GPS-based navigation, returning state estimates at 12 Earth radii. In early 2017 MMS transitioned to its second phase which doubled the apogee distance to 25 Earth radii, approaching halfway to the Moon. This paper will present results for GPS observability and navigation performance achieved in MMS Phase 2. Additionally, it will provide simulation results predicting the performance of the MMS navigation system applied to a pair of concept missions at Lunar distances. These studies will demonstrate how high-sensitivity GPS (or GNSS) receivers paired with onboard navigation software, as in MMS-Navigation system, can extend the envelope of autonomous onboard GPS navigation far from the Earth.

Winternitz, Luke B.↗
NASA NTRS2017

Development and Testing of a Multi-Transducer System for Measuring Height of Condensed Water in Steam Pipes with Steady-State and Turbulent Flow Conditions

One of the critical requirements for ensuring the safety of a steam pipe is to monitor the condensed water level under operation. For this objective, the authors initially developed methods and obtained preliminary test results based on the use of ultrasonic pulse-echo transducers and enhanced signal-processing tool; however, the methodology needed further development in order to obtain measurements in turbulent dynamic flow conditions. To improve the reliability of measurements taken in turbulent flow conditions, an experimental system was developed using multiple transducers driven by a multiplexer, and a data acquisition module capable of operating in any flow conditions. The system consists of a simulation testbed, which allows testing the performance over a range of flow rates and water levels and to observe flow conditions and patterns, as well as measure actual water level, flow velocities, wave conditions, etc. In this paper, we present the development details that include description of the testbed for simulating the flow of condensed water, the multiple transducers arrangement, the signal processing method, and the test results of both steady state and turbulent flow.

Lih, Shyh-Shiuh↗
NASA NTRS2004

Characteristics of Heavy Summer Rainfall in Southwestern Taiwan in Relation to Orographic Effects

On the windward side of southwestern Taiwan, about a quarter to a half of all rainfall during mid-July through August from 1994 to 2000 came from convective systems embedded in the southwesterly monsoon flow. k this study, the causes of two heavy rainfall events (daily rainfall exceeding 100 mm day over at least three rainfall stations) observed over the slopes and/or lowlands of southwestern Taiwan were examined. Data from European Center for Medium-Range Weather Forecasts /Tropical Ocean- Global Atmosphere (EC/TOGA) analyses, the rainfall stations of the Automatic Rainfall and Meteorological Telemetry System (ARMTS) and the conventional surface stations over Taiwan, and the simulation results from a regional-scale numerical model were used to accomplish the objectives. In one event (393 mm day on 9 August 1999), heavy rainfall was observed over the windward slopes of southern Taiwan in a potentially unstable environment with very humid air around 850 hPa. The extreme accumulation was simulated and attributed to orographic lifting effects. No preexisting convection drifted in from the Taiwan Strait into western Taiwan.

Chen, Ching-Sen↗
NASA NTRS1992

DIAL simulations for satellite water vapor profile measurements within the BEST project

The project BEST has been proposed by several laboratories of the French Space Agency (CNES) as part of the GEWEX program. Its objective is the study of the energy budget of the tropical system, and aims at measuring different components of the water cycle by coupling several observing systems. As part of this, Service d'Aeronomie (SA) proposed to study a Differential Absorption Lidar (DIAL) system to measure tropical water vapor profiles and to determine humidity convergence fields, when coupled with the Doppler wind lidar. We have performed simulation analyses for water vapor measurement from the selected orbit of 400 km. For these simulations, we have adopted an atmospheric model developed at SA. We have optimized, by a Monte Carlo statistical method, the system parameters and evaluated bias and standard deviation of the retrieved water vapor mixing ratio.

Chazette, P.↗