SEARCH · Engineering Papers

Results for “Mechanical Power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Atomic Oxygen (ATOX) simulation of Teflon FEP and Kapton H surfaces using a high intensity, low energy, mass selected, ion beam facility

A high intensity (greater than 10(exp 15) ions/sq cm) low energy (down to 5 eV) mass selected ion beam (MSIB) facility was used to study the effects of ATOX on two polymers commonly used for space applications (Kapton H and Teflon FEP). The polymers were exposed to O(+) and Ne(+) fluences on 10(exp 15) - 10(exp 19) ions/sq cm, using 30eV ions. A variety of analytical methods were used to analyze the eroded surfaces including: (1) atomic force microscopy (AFM) for morphology measurements; (2) total mass loss measurements using a microbalance; (3) surface chemical composition using x-ray photoelectron spectroscopy (XPS), and (4) residual gas analysis (RGA) of the released gases during bombardment. The relative significance of the collisional and chemical degradation processes was evaluated by comparing the effects of Ne(+) and O(+) bombardment. For 30 eV ions it was found that the Kapton is eroded via chemical mechanisms while Teflon FEP is eroded via collisional mechanisms. AFM analysis was found very powerful in revealing the evolution of the damage from its initial atomic scale (roughness of approx. 1 nm) to its final microscopic scale (roughness greater than 1 micron). Both the surface morphology and the average roughness of the bombarded surfaces (averaged over 1 micron x 1 micron images by the system's computer) were determined for each sample. For 30 eV a non linear increase of the Kapton roughness with the O(+) fluence was discovered (a slow increase rate for fluences phi less than 5 x 10(exp 17) O(+)/sq cm, and a rapid increase rate for phi greater than 5 x 10(exp 17) O(+)/sq cm). Comparative studies on the same materials exposed to RF and DC oxygen plasmas indicate that the specific details of the erosion depend on the simulation facility emphasizing the advantages of the ion beam facility.

Vered, R.↗

NASA NTRS1994

Active weld control

Through the two phases of this contract, sensors for welding applications and parameter extraction algorithms have been developed. These sensors form the foundation of a weld control system which can provide action weld control through the monitoring of the weld pool and keyhole in a VPPA welding process. Systems of this type offer the potential of quality enhancement and cost reduction (minimization of rework on faulty welds) for high-integrity welding applications. Sensors for preweld and postweld inspection, weld pool monitoring, keyhole/weld wire entry monitoring, and seam tracking were developed. Algorithms for signal extraction were also developed and analyzed to determine their application to an adaptive weld control system. The following sections discuss findings for each of the three sensors developed under this contract: (1) weld profiling sensor; (2) weld pool sensor; and (3) stereo seam tracker/keyhole imaging sensor. Hardened versions of these sensors were designed and built under this contract. A control system, described later, was developed on a multiprocessing/multitasking operating system for maximum power and flexibility. Documentation for sensor mechanical and electrical design is also included as appendices in this report.

Powell, Bradley W.↗

NASA NTRS1997

Low-Earth-Orbit (LEO) Life Cycle Evaluation of Nickel-Zinc Batteries

The conclusion of the Low-Earth-Orbit (LEO) life cycle evaluation of nickel-zinc batteries are: that composite nickel electrode provide excellent performance at a reduced weight and lower cost; calcium / zinc electrode minimizes shape change; unioptimized cell designs yield 60 Wh/kg; nickel-zinc delivers 600 cycles at 80% DOD; long cycle life obtainable at low DOD; high rate capability power density; long-term failure mechanism is stack dry; and anomalous overcharge (1120%) greatly affected cell performance but did not induce failure and was recoverable.

Coates, D.↗

NASA NTRS2002

SMEX-Lite Modular Solar Array Architecture

For the most part, Goddard solar arrays have been custom designs that are unique to each mission. The solar panel design has been frozen prior to issuing an RFP for their procurement. There has typically been 6-9 months between RFP release and contract award, followed by an additional 24 months for performance of the contract. For Small Explorer (SMEX) missions, with three years between mission definition and launch, this has been a significant problem. The SMEX solar panels have been sufficiently small that the contract performance period has been reduced to 12-15 months. The bulk of this time is used up in the final design definition and fabrication of flight solar cell assemblies. Even so, it has been virtually impossible to have the spacecraft design at a level of maturity sufficient to freeze the solar panel geometry and release the RFP in time to avoid schedule problems with integrating the solar panels to the spacecraft. With that in mind, the SMEX-Lite project team developed a modular architecture for the assembly of solar arrays to greatly reduce the cost and schedule associated with the development of a mission- specific solar array. In the modular architecture, solar cells are fabricated onto small substrate panels. This modular panel (approximately 8.5" x 17" in this case) becomes the building block for constructing solar arrays for multiple missions with varying power requirements and geometrical arrangements. The mechanical framework that holds these modules together as a solar array is the only mission-unique design, changing in size and shape as required for each mission. There are several advantages to this approach. First, the typical solar array development cycle requires a mission unique design, procurement, and qualification including a custom qualification panel. With the modular architecture, a single qualification of the SMEX-Lite modules and the associated mechanical framework in a typical configuration provided a qualification by similarity to multiple missions. It then becomes possible to procure solar array modules in advance of mission definition and respond quickly and inexpensively to a selected mission's unique requirements. The solar array modular architecture allows the procurement of solar array modules before the array geometry has been frozen. This reduces the effect of procurement lead-time on the mission integration and test flow by as much as 50%. Second, by spreading the non-recurring costs over multiple missions, the cost per unit area is also reduced. In the case of the SMEX-Lite procurement, this reduction was by about one third of the cost per unit area compared to previous SMEX mission-unique procurements. Third, the modular architecture greatly facilitates the infusion of new solar cell technologies into flight programs as these technologies become available. New solar cell technologies need only be fabricated onto a standard-sized module to be incorporated into the next available mission. The modular solar array can be flown in a mixed configuration with some new and some standard cell technologies. Since each module has its own wiring terminals, the array can be arranged as desired electrically with little impact to cost and schedule. The solar array modular architecture does impose some additional constraints on systems and subsystem engineers. First, they must work with discrete solar array modules rather than size the array to fit exactly within an available envelope. The array area is constrained to an integer multiple of the module area. Second, the modular design is optimized for space radiation and thermal environments not greatly different from a typical SMEX LEO environment. For example, a mission with a highly elliptical orbit (e.g., Polar, SMEX/FAST) would require thicker coverglasses to protect the solar cells from the more intense radiation environment.

Lyons, John↗

NASA NTRS2002

Characterization of 2219 Aluminum Produced by Electron Beam Freeform Fabrication

Researchers at NASA Langley Research Center are developing a new electron beam freeform fabrication (EB F(sup 3)) technique to fabricate metal parts. This process introduces metal wire into a molten pool created by a focused electron beam. Potential aerospace applications for this technology include ground-based fabrication of airframe structures and on-orbit construction and repair of space components and structures. Processing windows for reliably producing high quality 2219 aluminum parts using the EB F(sup 3) technique are being defined. The effects of translation speed, wire feed rate, and beam power on the resulting microstructures and mechanical properties are explored. Tensile properties (ultimate tensile strength, yield strength, and elongation) show little effect over the range of processing conditions tested. Basic processing-microstructure-property correlations are drawn for the EB F(sup 3) process.

Taminger, Karen M. B.↗

NASA NTRS2003

Investigation of Combined Motor/Magnetic Bearings for Flywheel Energy Storage Systems

Dr. Hofmann's work in the summer of 2003 consisted of two separate projects. In the first part of the summer, Dr. Hofmann prepared and collected information regarding rotor losses in synchronous machines; in particular, machines with low rotor losses operating in vacuum and supported by magnetic bearings, such as the motor/generator for flywheel energy storage systems. This work culminated in a presentation at NASA Glenn Research Center on this topic. In the second part, Dr. Hofmann investigated an approach to flywheel energy storage where the phases of the flywheel motor/generator are connected in parallel with the phases of an induction machine driving a mechanical actuator. With this approach, additional power electronics for driving the flywheel unit are not required. Simulations of the connection of a flywheel energy storage system to a model of an electromechanical actuator testbed at NASA Glenn were performed that validated the proposed approach. A proof-of-concept experiment using the D1 flywheel unit at NASA Glenn and a Sundstrand induction machine connected to a dynamometer was successfully conducted.

Hofmann, Heath↗

NASA NTRS1946

The Further Development of Heat-Resistant Materials for Aircraft Engines

The present report deals with the problems involved in the greater utilization and development of aircraft engine materials, and specifically; piston materials, cylinder heads, exhaust valves, and exhaust gas turbine blading. The blades of the exhaust gas turbine are likely to be the highest stressed components of modern power plants from a thermal-mechanical and chemical standpoint, even though the requirements on exhaust valves of engines with gasoline injection are in general no less stringent. For the fire plate in Diesel engines the specifications for mechanical strength and design are not so stringent, and the question of heat resistance, which under these circumstances is easier obtainable, predominates.

Bollenrath, Franz↗

NASA NTRS2005

G2 Flywheel Module Operated at 41,000 rpm

NASA Glenn Research Center s Flywheel Development Team designed, built, and successfully operated the new G2 flywheel to 41,000 rpm on September 2, 2004. This work was supported by the Aerospace Flywheel Technology Program--a NASA Office of Aerospace Technology ETC Program funded by the Energetics Project. The work was performed by a team of civil servants, contractors, and grantees managed by Glenn s Electrical Systems Development Branch, Structural Mechanics and Dynamics Branch, and Space Power & Propulsion Test Engineering Branch. The G2 flywheel was designed to be a low-cost modular testbed for flywheel system integration and component demonstrations.

Ralph H Jansen↗

NASA NTRS2005

Space Tethers Programmatic Infusion Opportunities

Programmatic opportunities abound for space Cables, Stringers and Tethers, justified by the tremendous performance advantages that these technologies offer and the rather wide gaps that must be filled by the NASA Exploration program, if the "sustainability goal" is to be met. A definition and characterization of the three categories are presented along with examples. A logical review of exploration requirements shows how each class can be infused throughout the program, from small experimental efforts to large system deployments. The economics of tethers in transportation is considered along with the impact of stringers for structural members. There is an array of synergistic methodologies that interlace their fabrication, implementation and operations. Cables, stringers and tethers can enhance a wide range of other space systems and technologies, including power storage, formation flying, instrumentation, docking mechanisms and long-life space components. The existing tether (i.e., MXER) program's accomplishments are considered consistent with NASA's new vision and can readily conform to requirements-driven technology development.

Bonometti, J. A.↗

NASA NTRS2006

Design of a Long Endurance Titan VTOL Vehicle

Saturn s moon Titan promises insight into many key scientific questions, many of which can be investigated only by in situ exploration of the surface and atmosphere of the moon. This research presents a vertical takeoff and landing (VTOL) vehicle designed to conduct a scientific investigation of Titan s atmosphere, clouds, haze, surface, and any possible oceans. In this investigation, multiple options for vertical takeoff and horizontal mobility were considered. A helicopter was baselined because of its many advantages over other types of vehicles, namely access to hazardous terrain and the ability to perform low speed aerial surveys. Using a nuclear power source and the atmosphere of Titan, a turbo expander cycle produces the 1.9 kW required by the vehicle for flight and operations, allowing it to sustain a long range, long duration mission that could traverse the majority of Titan. Such a power source could increase the lifespan and quality of science for planetary aerial flight to an extent that the limiting factor for the mission life is not available power but the life of the mechanical parts. Therefore, the mission could potentially last for years. This design is the first to investigate the implications of this potentially revolutionary technology on a Titan aerial vehicle.

Prakash, Ravi↗

NASA NTRS2011

Combined Structural and Trajectory Control of Variable-Geometry Planetary Entry Systems

Some of the key challenges of planetary entry are to dissipate the large kinetic energy of the entry vehicle and to land with precision. Past missions to Mars were based on unguided entry, where entry vehicles carried payloads of less than 0.6 T and landed within 100 km of the designated target. The Mars Science Laboratory (MSL) is expected to carry a mass of almost 1 T to within 20 km of the target site. Guided lifting entry is needed to meet these higher deceleration and targeting demands. If the aerodynamic characteristics of the decelerator are variable during flight, more trajectory options are possible, and can be tailored to specific mission requirements. In addition to the entry trajectory modulation, having variable aerodynamic properties will also favor maneuvering of the vehicle prior to descent. For proper supersonic parachute deployment, the vehicle needs to turn to a lower angle of attack. One approach to entry trajectory improvement and angle of attack control is to embed a variable geometry decelerator in the design of the vehicle. Variation in geometry enables the vehicle to adjust its aerodynamic performance continuously without additional fuel cost because only electric power is needed for actuating the mechanisms that control the shape change. Novel structural and control concepts have been developed that enable the decelerator to undergo variation in geometry. Changing the aerodynamic characteristics of a flight vehicle by active means can potentially provide a mechanically simple, affordable, and enabling solution for entry, descent, and landing across a wide range of mission types, sample capture and return, and reentry to Earth, Titan, Venus, or Mars. Unguided ballistic entry is not sufficient to meet this more stringent deceleration, heating, and targeting demands. Two structural concepts for implementing the cone angle variation, a segmented shell, and a corrugated shell, have been presented.

Quadrelli, Marco B.↗

NASA NTRS2013

The Thermal Hogan - A Means of Surviving the Lunar Night

document describes the Thermal Hogan, a new shelter concept that would be used on the Moon to moderate the extreme nighttime temperatures, allowing survival of equipment with minimal heater power. It is lightweight, has few mechanical parts, and would be relatively easy to deploy on the Moon. The Lunar Hogan has two parts: an insulated shelter and a thermal mass. The shelter is constructed of multilayer insulation (MLI) draped over a structural framework. Entry and egress are accomplished either by raising the structure or via a door constructed of the same MLI material as the shelter. The thermal mass can be manufactured from locally available materials, either by piling substantially sized rocks to a depth of 0.25 meter, or by filling a 0.25-meter-deep conductive honeycomb-like structure with lunar dust. For ease of transport, the structural framework and honeycomb can be collapsible. The door can be opened by pushing on it in either direction. Gravity would cause it to close and it could be sealed via magnetic strips on the doorframe.

Fruitwala, Neelay↗

NASA NTRS2017

Multifunctional Structures for High-Energy Lightweight Load-Bearing Storage

The Multifunctional Structures for High Energy Lightweight Load-bearing Storage (M-SHELLS) subproject is evaluating the feasibility of a structural hybrid super-capacitor concept, drawn from recent nano-technology advances in both electrochemistry and microstructures to create a transformative multi-functional airframe material which carries structural load and stores energy to save weight and enable electric aero propulsion. Multi-disciplinary engineering approach assures high energy storage and power levels, as well as good mechanical attributes.

Loyselle, Patricia↗

NASA NTRS2018

The CEOS Data Cube Portal: A User-Friendly, Open Source Software Solution for the Distribution, Exploration, Analysis, and Visualization of Analysis Ready Data

There is an urgent need to increase the capacity of developing countries to take part in the study and monitoring of their environments through remote sensing and space-based Earth observation technologies. The Open Data Cube (ODC) provides a mechanism for efficient storage and a powerful framework for processing and analyzing satellite data. While this is ideal for scientific research, the expansive feature space can also be daunting for end-users and decision-makers who simply require a solution which provides easy exploration, analysis, and visualization of Analysis Ready Data (ARD). Utilizing innovative web-design and a modular architecture, the Committee on Earth Observation Satellites (CEOS) has created a web-based user interface (UI) which harnesses the power of the ODC yet provides a simple and familiar user experience: the CEOS Data Cube (CDC). This paper presents an overview of the CDC architecture and the salient features of the UI. In order to provide adaptability, flexibility, scalability, and robustness, we leverage widely-adopted and well-supported technologies such as the Django web framework and the AWS Cloud platform. The fully-customizable source code of the UI is available at our public repository. Interested parties can download the source and build their own UIs. The UI empowers users by providing features that assist with streamlining data preparation, data processing, data visualization, and sub-setting ARD products in order to achieve a wide variety of Earth imaging objectives through an easy to use web interface.

User Interface↗

NASA NTRS1993

Near Grazing Scattering from Non-Gaussian Ocean Surfaces

From the experimental ocean scattering data, it has been observed that the backscattering cross section of a horizontally polarized wave can be as large as the vertical connterpart at near grazing incidence.

near-grazing↗

NASA NTRS2022

Development and Validation of a Canfield Joint as a Precision Pointing System for Deep Space Instrumentation

A mission plan for an integrated radio and optical communications payload, based on the Mars Reconnaissance Orbiter, is presented with emphasis on the derivation of precision pointing requirements. The Canfield joint, a parallel robotic linkage capable of hemispherical pointing, is discussed as a platform for optical communication and other deep space instrumentation. The capabilities of a prototype are compared to those of currently available gimbals qualified for deep space, and the advantages of the Canfield joint, including size, weight and power (SWaP) savings, cable handling, and mechanical redundancy, are discussed. Validation procedures and results for the space hardware prototype are presented. This work was undertaken through the Integrated Radio and Optical Communication (iROC) project at NASA Glenn Research Center.

Laser optical communications↗

NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Laboratory: Overview and Capability

A hardware-in-the-loop (HIL) laboratory is developed to investigate control technologies for electrified aircraft propulsion (EAP). The laboratory emulates a propulsion system by reproducing the mechanical shaft interface to the electrical power system in hardware. The experimental electric power system includes supercapacitor energy storage and a dynamically variable electrical load. A novel method of scaling power and inertia is provided in software to accurately reproduce the transient, off-design turbomachinery performance dynamics without including actual turbomachinery. An overview of how the HIL system can accommodate a broad range of EAP architectures, including power extraction and insertion, with capability for transient energy management is described. The real-time system operates in the 100kW power class and is instrumented to emulate turbomachinery – power system interactions. The platform is an agile, flexible laboratory for low-cost, risk-reduction development and testing of propulsion control, operability, and energy management technologies.

Controls↗

NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Laboratory: Overview and Capability

controls↗