Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

NMR studies of the ground states of Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 Heusler alloys

Three temperature-induced phase transitions at T=T 1 , T M /T A , and T C , related to the ferromagnetic order of the martensitic phase (FMMP), martensitic (structural) transitions (MT), and the ferromagnetic order of the austenitic phase (FMAP), respectively, have been observed in the off-stoichiometric Heusler alloys, Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 . In this work, the phase transitions temperatures are found to be depended on alloy composition. A kinetic arrest of the AP was observed for Ni 47.5 Co 2.5 Mn 35 In 15 in the magnetization measurements during field-cooling cycle (FCC) at 50 kOe. Depending upon the cooling protocols, ZFC and FCC (at H = 50 kOe), two different ground states of the alloys can be found in Ni 47.5 Co 2.5 Mn 35 In 15 and Ni 45 Co 5 Mn 37 In 13 alloys. The ground states (T=4.2 K and external field H=0) of the alloys was found to be characterized by three main line: two, partially overlapping, at higher frequencies (300-450 MHz), most likely corresponding of manganese resonance lines and one at lower frequency at about 200 MHz. A significant shift in the spectrum of Ni 45 Co 5 Mn 37 In 13 by about 100 MHz to higher frequencies was observed. The correlation of magnetizations obtained from magnetic moment and NMR studies is discussed.

36 MATERIALS SCIENCE↗

Effects of doping, hydrostatic pressure, and thermal quenching on the phase transitions and magnetocaloric properties in Mn 1– x Co x NiGe

The effects of doping, hydrostatic pressure, and thermal quenching on the phase transitions and magnetocaloric properties of the Mn 1–x Co x NiGe system have been investigated. Cobalt doping on the Mn site shifted the martensitic structural transition toward lower temperature until it was ultimately absent, leaving only a magnetic transition from a ferromagnetic (FM) to a paramagnetic (PM) state in the high-temperature hexagonal phase. Co-occurrence of the magnetic and structural transitions to form a first-order magnetostructural transition (MST) from the FM orthorhombic to the PM hexagonal phase was observed in samples with 0.05 < x < 0.20. An additional antiferromagnetic–ferromagnetic-like transition was observed in the martensite phase for 0.05 < x < 0.10, which gradually vanished with increasing Co concentration (x > 0.10) or magnetic field (H > 0.5 T). The application of external hydrostatic pressure shifted the structural transition to lower temperature until an MST was formed in samples with x = 0.03 and 0.05, inducing large magnetic entropy changes up to –80.3 J kg –1 K –1 (x = 0.03) for a 7-T field change under 10.6-kbar pressure. Similar to the effects of the application of hydrostatic pressure, an MST was formed near room temperature in the sample with x = 0.03 by annealing at high temperature (1200 °C) followed by quenching, resulting in a large magnetic entropy change of –56.2 J kg –1 K –1 . Furthermore, these experimental results show that the application of pressure and thermal quenching, in addition to compositional variations, are effective methods to create magnetostructural transitions in the MnNiGe system, resulting in large magnetocaloric effects.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Assessment of minnealloy fabrication via three routes

Transformer cores exhibiting higher operating power and improved efficiency are of great interest to electrical utilities, industry, and the de-carbonization effort. Minnealloy, α″-Fe16(C,N)2, a martensite made only of iron, nitrogen, and carbon, has shown the largest saturation magnetization of any soft ferromagnet, 250 emu/g, and tunable magnetocrystalline anisotropy. Given this represents a significant increase in power transferred per cycle compared to legacy transformer core materials, we investigate three novel, industrially scalable routes for fabricating Minnealloy. The martensite phase content is investigated for each route. Vibrating sample magnetometry is used to investigate the change in saturation magnetization and coercivity with respect to the relative content of the desired phase and other iron, iron-nitride, and iron oxide phase impurities. The relationship between structure and magnetic properties of bulk α″-Fe16(C,N)2 is investigated using LDA, PBE, and PBEsol exchange-correlation functionals within the frameworks of Hubbard-corrected density functional theory (DFT+U).

36 MATERIALS SCIENCE↗

Reply to Martinez-Canales et al.: The structure(s) of lithium at low temperatures

In our recent article, we proposed that Fermiology measurements can be used as a complementary probe for determining the low-temperature state of Li. In a letter criticizing our conclusions, Martinez-Canales, Loa, and Ackland (MLA) claim (i) that “obtaining dHvA signals from martensitic microstructures is usually impossible” and (ii) that the experimental data of Hunt et al., in particular, cannot be used to infer useful information about the martensitic phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Atom-probe study of Cu and NiAl nanoscale precipitation and interfacial segregation in a nanoparticle-strengthened steel

The Cu and NiAl nanoscale precipitation and interfacial segregation in the martensite and austenite phases within a high-strength steel were studied by atom-probe tomography (APT). In the martensite phase, APT reveals the precipitation of isolated NiAl nanoparticles and NiAl/Cu co-precipitates, indicating that NiAl nanoparticles form first in the precipitation sequence. In comparison, the austenite phase contains only Cu nanoparticles with Ni segregation at the particle/matrix interface, in which the Ni segregation reduces the Cu nanoparticle interfacial energy. In addition, Mn and C exhibit an enrichment at the martensite/austenite interface, and the mechanism for the interfacial segregation was also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Large magnetocaloric effect in rapidly quenched Mn 50- x Co x Ni 40 In 10 nanomaterials

The effect of Co addition on magnetic hysteresis, martensitic transformation temperature, and magnetic entropy change of rapidly-quenched Mn 50- x Co x Ni 40 In 10 alloy nanomaterials has been investigated. The melt-spun Mn 50 Ni 40 In 10 sample exhibits a small magnetic hysteresis which is further reduced by Co doping as measured between 0 and 2 T. The martensitic transformation temperature increases linearly with the electron concentration in the alloy from 195 K for Mn 50 Ni 40 In 10 to 378 K for Mn 45 Co 5 Ni 40 In 10 . The Mn 47 Co 3 Ni 40 In 10 alloy, which has phase-transition temperature close to room temperature, exhibits a substantial peak entropy change of 29.7 J kg -1 K -1 at magnetic field change of 2 T. Our results demonstrate that Mn 47 Co 3 Ni 40 In 10 nanomaterial exhibits promising magnetocaloric properties for near-room-temperature magnetic refrigeration.

Physics↗

Controlling phase transitions in MnNiGe using thermal quenching and hydrostatic pressure

Here, the phase transitions in MnNiGe compounds were explored by manipulating the heat treatment conditions and through hydrostatic pressure application. As the quenching temperature increased, both the first-order martensitic structural transition temperatures and magnetic transition temperatures decreased relative to those in the slowly-cooled samples. When the samples were quenched from 1200 °C, the first-order martensitic structural transition temperature lowered by more than 200 K. The structural transitions also shifted to lower temperature with the application of hydrostatic pressure during measurement. Temperature-dependent x-ray diffraction results reveal that the changes of the cell parameters resulting from the structural transitions are nearly identical for all samples regardless of the extensive variation in their structural transition temperatures. In addition, neutron scattering measurements confirm the magnetic structure transition between simple and cycloidal spiral magnetic structures.

36 MATERIALS SCIENCE↗

In situ measurement of phase transformations and residual stress evolution during welding using spatially distributed fiber-optic strain sensors

Welding of high-strength steels can result in large tensile strains as the base metal and filler material cool from their molten state. To combat these large tensile strains, low-transformation-temperature (LTT) metal fillers have been proposed. These fillers undergo a martensitic phase transformation at a lower temperature which can ultimately reduce the tensile strain or can even introduce compressive strain adjacent to the weld metal. However, the process for optimizing the composition of the LTT material, as well as various weld parameters for each unique weld geometry, can be quite expensive, especially if the acceptance criterion requires using neutrons, x-ray beams, or destructive techniques to characterize residual stresses. This work describes a simple, low-cost method for quantifying residual stresses and phase transformations in situ during welding. Spatially distributed fiber-optic sensors were bonded to a cast iron plate, along with tack-welded thermocouples, to measure temperature and strain during multiple passes with LTT filler metals. Results show that the fiber-optic sensors can successfully resolve compressive strain adjacent to the weld region caused by the martensitic phase transformations in the LTT filler material.

47 OTHER INSTRUMENTATION↗

Fermi surface studies of the low-temperature structure of sodium

Sodium is the most abundant alkali-metal element and has one of the simplest electronic structures of any metal. At ambient conditions, sodium forms a body-centered-cubic lattice. However, during cooling, it undergoes a partial martensitic phase transition to a complex mixture of rhombohedral polytypes commencing from 36 K. Although the Fermi surface (FS) of bcc sodium has been extensively studied, not much attention has been given to the FS of the martensite structure. Here we report results for the Fermi surface and quantum oscillation (QO) frequencies of several energetically favorable crystal structures of Na at low temperature from first-principles calculations. Interestingly we find that despite drastic differences in the crystal structures of the candidate low-temperature phases of sodium, for all these phases the strongest quantum oscillation peak is centered at 28 kT. Our theoretical results are accompanied by experimental data of QO on a multigrain sodium sample at T = 0.3 K and B max = 18 T exhibiting a sharp peak at 28 kT, independent of the sample orientation. The persistence of this peak even in the presence of the structural transitions has an implication for using the quantum oscillations of polycrystalline sodium for high magnetic field calibration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Intermittent dynamics in externally driven ferroelastics and strain glasses

The interplay of elastic anisotropy and disorder dictates many of the properties of ferroic materials, specifically martensites. Here we use a phase-field model for ferroelastic athermal materials to study their response to an increasing external stress that couples to the strain order parameter. We show that these systems evolve through avalanches and study the avalanche-size distribution for ferroelastic systems (large anisotropy and/or small disorder) and for the strain glass (small anisotropy and/or large disorder) using various statistical analysis techniques, including the maximum likelihood method. The model predicts that in the former case the distribution is subcritical or power law (in agreement with experimental observations), whereas in the latter case it becomes supercritical. Finally, our results are consistent with experiments on martensitic materials, and we predict specific avalanche behavior that can be tested and used as an alternative means to characterize strain glasses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crystal plasticity analysis of stress partitioning mechanisms and their microstructural dependence in advanced steels

Two-phase advanced steels contain an optimized combination of high yield strength and large elongation strain at failure, as a result of stress partitioning between a hard phase (martensite) and a ductile phase (ferrite or austenite). Provided with strong interfaces between the constituent phases, the failure in the brittle martensite phase will be delayed by the surrounding geometric constraints, while the rule of mixture will dictate a large strength of the composite. To this end, the microstructural design of these composites is imperative especially in terms of the stress partitioning mechanisms among the constituent phases. Based on the characteristic microstructures of dual phase and multilayered steels, two polycrystalline aggregate models are constructed to simulate the microscopic lattice strain evolution of these materials during uniaxial tensile tests. By comparing the lattice strain evolution from crystal plasticity finite element simulations with advanced in situ diffraction measurements in literature, this study investigates the correlations between the material microstructure and the micromechanical interactions on the intergranular and interphase levels. Finally, it is found that although the applied stress will be ultimately accommodated by the hard phase and hard grain families, the sequence of the stress partitioning on grain and phase levels can be altered by microstructural designs. Implications of these findings on delaying localized failure are also discussed.

36 MATERIALS SCIENCE↗

A novel physics-based and data-supported microstructure model for part-scale simulation of laser powder bed fusion of Ti-6Al-4V

The elasto-plastic material behavior, material strength and failure modes of metals fabricated by additive manufacturing technologies are significantly determined by the underlying process-specific microstructure evolution. In this work a novel physics-based and data-supported phenomenological microstructure model for Ti-6Al-4V is proposed that is suitable for the part-scale simulation of laser powder bed fusion processes. The model predicts spatially homogenized phase fractions of the most relevant microstructural species, namely the stable β-phase, the stable α s -phase as well as the metastable Martensite α m -phase, in a physically consistent manner. In particular, the modeled microstructure evolution, in form of diffusion-based and non-diffusional transformations, is a pure consequence of energy and mobility competitions among the different species, without the need for heuristic transformation criteria as often applied in existing models. The mathematically consistent formulation of the evolution equations in rate form renders the model suitable for the practically relevant scenario of temperature- or time-dependent diffusion coefficients, arbitrary temperature profiles, and multiple coexisting phases. Due to its physically motivated foundation, the proposed model requires only a minimal number of free parameters, which are determined in an inverse identification process considering a broad experimental data basis in form of time-temperature transformation diagrams. Subsequently, the predictive ability of the model is demonstrated by means of continuous cooling transformation diagrams, showing that experimentally observed characteristics such as critical cooling rates emerge naturally from the proposed microstructure model, instead of being enforced as heuristic transformation criteria. Eventually, the proposed model is exploited to predict the microstructure evolution for a realistic selective laser melting application scenario and for the cooling/quenching process of a Ti-6Al-4V cube of practically relevant size. Numerical results confirm experimental observations that Martensite is the dominating microstructure species in regimes of high cooling rates, e.g., due to highly localized heat sources or in near-surface domains, while a proper manipulation of the temperature field, e.g., by preheating the base-plate in selective laser melting, can suppress the formation of this metastable phase.

Inverse parameter identification↗

Multitask graph neural networks for elastoplastic response prediction in dual-phase polycrystals

Microstructure-sensitive prediction of elastoplastic response remains a recurring bottleneck in multiscale damage and fatigue modeling, where large ensembles of statistically distinct polycrystals are required to quantify variability and extreme-value behavior. In this work, we develop a multitask graph neural network (GNN) surrogate that maps dual-phase ferrite–martensite polycrystal microstructures to Statistical Volume Element (SVE)-level elastoplastic Quantities of Interest (QoIs). Each SVE is represented as a grain-adjacency graph, with node features encoding phase, geometry, and crystallographic orientation, and edge features encoding relative misorientation. A message-passing graph convolution generates node embeddings, which are pooled into a graph representation and passed to a multitask regression head that jointly predicts 10 scalar QoIs and vector-valued stress–strain responses in orthogonal loading directions across multiple martensite volume fractions and SVE sizes. Results show high accuracy for scalar QoIs and strong agreement for full stress–strain trajectories, with population envelopes reproducing both median behavior and finite-SVE variability across compositions and partition scales. A unified model trained on pooled volume-fraction data preserves most within-regime accuracy relative to regime-specific models while also capturing the broader cross-regime variation reflected in the pooled test set. Distributional comparisons further demonstrate that the surrogate preserves heterogeneity under SVE partitioning, enabling statistically consistent block-wise random-field construction for mesoscale analyses. Overall, the proposed grain-graph surrogate provides a practical pathway to accelerate ensemble-based studies of SVE-level constitutive variability in dual-phase polycrystals.

Crystal plasticity↗

Characterization of microstructure and property evolution in advanced cladding and duct: Materials exposed to high dose and elevated temperature

Designing materials for performance in high-radiation fields can be accelerated through a carefully chosen combination of advanced multiscale modeling paired with appropriate experimental validation. Here, the studies reported in this work, the combined efforts of six universities working together as the Consortium on Cladding and Structural Materials, use that approach to focus on improving the scientific basis for the response of ferritic–martensitic steels to irradiation. A combination of modern modeling techniques with controlled experimentation has specifically focused on improving the understanding of radiation-induced segregation, precipitate formation and growth under radiation, the stability of oxide nanoclusters, and the development of dislocation networks under radiation. Experimental studies use both model and commercial alloys, irradiated with both ion beams and neutrons. Lastly, transmission electron microscopy and atom probe are combined with both first-principles and rate theory approaches to advance the understanding of ferritic–martensitic steels.

36 MATERIALS SCIENCE↗

Shape Memory Alloys and their Applications in Power Generation and Refrigeration

The shape memory effect is closely related to the reversible martensitic phase transformation, which is diffusionless and involves shear deformation. The recoverable transformation between the two phases with different crystalline symmetry results in reversible changes in physical properties such as electrical conductivity, magnetization, and elasticity. Accompanying the transformation is a change of entropy. Fascinating applications are developed based on these changes. In this paper, the history, fundamentals and technical challenges of both thermoelastic and ferromagnetic shape memory alloys are briefly reviewed; applications related to energy conversion such as power generation and refrigeration as well as recent developments will be discussed.

energy generation↗

Report on Thermal Aging Effects on Tensile Properties of Advanced Austenitic Steels

This report provides an update on the evaluation of thermal-aging induced degradation of tensile properties of advanced HT-UPS austenitic stainless steels. The report is the second deliverable (level 3) in FY11 (M3A11AN04030103), under the Work Package A-11AN040301, “Advanced Alloy Testing” performed by Argonne National Laboratory, as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing tensile data on aged alloys and a mechanistic model, validated by experiments, with a predictive capability on long-term performance. The scope of work is to evaluate the effect of thermal aging on the tensile properties of advanced alloys such as ferritic-martensitic steels, mod.9Cr-1Mo (G91), G92, and advanced austenitic stainless steel, HT-UPS. The aging experiments have been conducted over a temperature of 550-750°C for various time periods to simulate the microstructural changes in the alloys. In addition, a mechanistic model based on thermodynamics and kinetics has been used to address the changes in microstructure of the alloys as a function of time and temperature, which is developed in the companion work package at ANL. The focus of this project is advanced alloy testing and understanding the effects of long-term thermal aging on the tensile properties. The first deliverable of FY11 reported the tensile testing results of thermally-aged G92 in the normalized and tempered condition (H1 G92), G92 in the cold-rolled condition (H2 G92), and reference alloy, G91 ferritic-martensitic steels. This report summarizes the tensile data of thermally aged HT-UPS austenitic stainless steel. Two heats of HT-UPS have been investigated, i.e., solution-annealed HT-UPS (SA HT-UPS) and hot-rolled HT-UPS (HR HT-UPS). Tensile data have been obtained for SA HT-UPS thermally-aged for up to 18031 h at 550°C and for up to 17595 h at 650°C, as well as for HR HT-UPS thermally aged for up to 6909 h at 550°C, 4293 h at 600°C, and 5407 h at 650°C. Major finding are: (1) the solution-annealed HT-UPS showed continued, moderate increase in strength and decrease in ductility with increasing aging time up to 18034 h at 550°C. Thermal aging at 650°C increased the yield stress and decreased the ultimate tensile strength and drastically reduced the ductility in the SA HT-UPS. For the HR HT-UPS, thermal aging at 550°C for up to 6909 h showed little influence on its tensile behavior. Thermal aging at 600°C for 4293 h increased the strength and decreased the ductility. The 650°C-thermally-aged HR HT-UPS specimens showed very different strengthening, strain hardening, and flow localization behavior. Thermal aging at 650°C increased the yield stress but decreased the ultimate tensile stress for the HR HT-UPS. (2) Dynamic strain aging (DSA) was observed in both the solution-annealed HT-UPS and the hot-rolled HT-UPS at temperatures between 550-650°C at a strain rate of 0.001 s -1 . Extensive precipitation in the matrix after thermal aging at 600 and 650°C significantly reduced serrated plastic flow observed in the stress-strain curves, i.e. less effect of DSA. Because the DSA phenomenon can have significant influence on tensile, creep strength, and fatigue resistance, and the DSA effects in HT-UPS steels were observed in the temperature range of interest to the SFR applications, the DSA phenomenon in the HT.

Li, Meimei↗

Mechanical Properties and Radiation Resistance of Nanoprecipitates-Strengthened Advanced Ferritic Alloys

Five ferritic alloys and a ferritic-martensitic steel, designed by computational thermodynamics using recently developed database, were assessed in this work. A previous Fe-Cr-Zr ferritic alloy, named as Z6, was further investigated because of its amorphization behavior after a peak damage of 50 displacements per atom (dpa) at 400°C. Alloying elements of Zr, Nb, and Mo were varied to form four new ferritic alloys, named as Z1N33A, BL-Nb, BL-NbZr, and BL-Mo, which have reduced Zr-bearing Laves phase and complemented with B2-NiAl phase. The ferritic-martensitic steel, named as TTZ2M, favored MX-type (M=metal, X=C/N) precipitates with controlled M 23 C 6 and Laves phases.

36 MATERIALS SCIENCE↗