Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LASER OUTPUT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

On the possibility of a new passively Q-switched laser operation mode with periodic wavelength switching

The possibility of cw-pumped passively Q-switched laser operation has been examined theoretically. Also, we have proposed laser operation mode in which the output wavelength automatically switches between two values without any changes in cavity parameters. Using numerical simulation and an Er:YAG laser with a Co:ZnSe passive Q-switch as an example, we have found parameters that ensure such operation mode. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Continuous-wave and actively Q-switched resonantly dual-end-pumped Er : YAG ceramic laser emitting at 1.6 μm

We demonstrate a continuous-wave (cw) and actively Q-switched Er : YAG ceramic laser resonantly dual-end-pumped by a 1532 nm fibre-coupled laser diode. A maximum cw output power of 1.48 W at 1645.3 nm is obtained at an absorbed pump power of 12.72 W, corresponding to a slope efficiency of 19.2%. In the Q-switched regime the maximum pulse energy of 0.84 mJ is reached at a pulse repetition rate of 100 Hz, pulse duration of 48.03 ns and absorbed pump power of 10.51 W. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An intensity-modulated dual-wavelength He-Ne laser for remote sensing of methane

A new type of dual wavelength He-Ne laser is described in which the output power at each of the two wavelengths is modulated with equal amplitude and opposite phase to each other. This laser source can greatly simplify the setup and improve the sensitivity of the differential absorption measurements for the methane detection, as verified by a preliminary experiment. A simple scheme to measure the concentration of methane is also proposed.

Uehara, K.↗

Temporal pre-pulse shaping in dual pulse laser produced plasma for the optimization of the EUV source in tin microdroplet system

Dual-laser beams interacting with small droplets of liquid tin are currently the most efficient systems for producing the 13.5 nm EUV photon radiation source required for the next generation microchips. Usually, EUV light is produced during the second main-pulse stage, while the pre-pulse (PP) is used for target preparation, i.e., droplet preheating, vaporization, and target deformation. However, the PP laser energy can be utilized more efficiently if the EUV producing plasma is being developed during the PP stage as well. In this work, we study the ways of optimization of the PP laser temporal shape to achieve conditions for maximum EUV output during the pre-pulse. The size of the deformed droplet is kept optimized for the following main laser pulse. Our simulations showed a significant increase in the EUV output at the pre-pulse stage when a ramping profile is used for the laser temporal shape. Using the ramped square pre-pulse produces 24% gain in the EUV output in comparison with the standard Gaussian temporal profile (i.e., regular Nd:YAG shape) for the same energy of the laser pulse.

36 MATERIALS SCIENCE↗

Efficient CW diode-pumped Tm, Ho:YLF laser with tunability near 2.067 microns

A conversion efficiency of 42 percent and slope efficiency of approximately 60 percent relative to absorbed pump power are reported from a continuous wave diode-pumped Tm, Ho:YLF laser at 2 microns with output power of 84 mW at sub-ambient temperatures. The emission spectrum is etalon tunable over a range of 16/cm centered on 2.067 microns, with fine tuning capability of the transition frequency with crystal temperature at a measured rate of about -0.03/cm-K. The effective emission cross section is measured to be 5 x 10 exp -21 sq cm. These and other aspects of the laser performance are discussed in the context of calculated atmospheric absorption characteristics in this spectral region and potential use in remote sensing applications.

Mcguckin, B. T.↗

Noise power spectral density of a fibre scattered-light interferometer with a semiconductor laser source

Spectral characteristics of the noise intensity fluctuations at the output of a scattered-light interferometer, caused by phase fluctuations of semiconductor laser radiation are considered. This kind of noise is one of the main factors limiting sensitivity of interferometric sensors. For the first time, to our knowledge, the expression is obtained for the average noise power spectral density at the interferometer output versus the degree of a light source coherence and length of the scattering segment. Also, the approximate expressions are considered which determine the power spectral density in the low-frequency range (up to 200 kHz) and in the limiting case of extended scattering segments. The expression obtained for the noise power spectral density agrees with experimental normalised power spectra with a high accuracy. (interferometry of radiation)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Self-Modulated Laser Rangefinder

Longitudinal resonance modes exploited. Self-modulated-laser ranging system exploits presence of signals differing in frequency by longitudinalmode separation frequency fm. Two square-law photodetectors have outputs modulated by fm, and phase difference between two outputs is related to target distance. Laser transmitter/receiver measures distances as well as displacements of distant objects (such as vibrating buildings).

Abshire, J. B.↗

Direct solar-pumped iodine laser amplifier

During this period the parametric studies of the iodine laser oscillator pumped by a Vortek simulator were carried out before amplifier studies. The amplifier studies are postponed to the extended period after completing the parametric studies. In addition, the kinetic modeling of a solar-pumped iodine laser amplifier, and the experimental work for a solar pumped dye laser amplifier are in progress. This report contains three parts: (1) a 10 W CW iodine laser pumped by a Vortek solar simulator; (2) kinetic modeling to predict the time to lasing threshold, lasing time, and energy output of solar-pumped iodine laser; and (3) the study of the dye laser amplifier pumped by a Tamarack solar simulator.

Han, K. S.↗

Optogalvanic stabilization and offset tuning of a carbon dioxide waveguide laser

A feedback loop employing the change in discharge impedance with output power is used to stabilize the frequency of a CO2 waveguide laser. The relatively high operating pressure of the laser combined with a zero offset feature in the feedback loop allows continuous tuning of the stabilized frequency over a 300-400 MHz range.

Kavaya, M. J.↗

Fiber-coupled laser-driven flyer plates system

A system for the launch of hypervelocity flyer plates has been developed and characterized. Laser-driven flyers were launched from the substrate backed aluminum-alumina-aluminum sandwiched films. A laser-induced plasma is used to drive flyers with typical thickness of 5.5 {mu}m and diameters of less than 1 mm, to achieve velocities of a few km/s. These flyer plates have many applications, from micrometeorite simulation to laser ignition. The flyer plates considered here have up to three layers: an ablation layer, to form plasma; an insulating layer; and a final, thicker layer that forms the final flyer plates. This technique was developed aiming at improving the energy efficiency of the system. The kinetic energy of flyers launched with the additional layer was found to be enhanced by a factor of near 2 (up to 30%). The optical fiber delivery system governs the output spatial profile of the laser spot and power capacity. Moreover, a technique for coupling high-power laser pulses into an optical fiber has been developed. This fiber optic system has been successfully used to launch flyer plates, and the surface finishing quality of the fiber was found to be an important factor. Importantly, measurements of the flyer performance including the mean velocities and planarity were made by an optical time-of-arrival technique using an optical fiber array probe, demonstrating the good planarity of the flyer and the achievable average velocity of 1.7 km/s with approaching 1 mm diameter. Finally, the relationship between flyer velocities and incident laser pulses energy was also investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the possibility of increasing the pulse energy of a passively Q-switched erbium glass minilaser

A simple method to increase the output energy of a passively Q-switched erbium glass laser is proposed. Using the amplitude modulation of losses at the active element face, the fundamental mode was reliably suppressed and the laser operated in a selected higher-order mode. The output energy was experimentally increased by a factor of 2.1, and the range of allowable pump energy instability was extended threefold. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-power optical parametric oscillator based on a high-pulse repetition rate, master Nd : KGW laser

An optical scheme of an optical parametric oscillator with a master laser based on an Nd : KGW active element excited by two orthogonally oriented diode side pump modules is proposed to form radiation pulses with energies above 30 mJ and a repetition rate of 1 – 20 Hz in the eye-safe spectral range of 1.5 – 1.6 μm. The two-module excitation of the active medium makes the distribution of the master laser radiation intensity in the output beam cross section more uniform and provides a reliable operation of the optical parametric oscillator. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser Texturing of Magnetic Recording Media Final Report CRADA No. TSV-1298-96

The Commercial Laser Systems Group at LLNL developed a concept for patterning of computer magnetic recording discs. Magnetic recording media require texturing over areas designated for contact in order to minimize friction with data transducing heads. In fabricating a hard disk, an aluminum nickel-phosphorous substrate was polished to a specular finish then a mechanical means was used to roughen an annular area intended to be the head contact band. In a previous patent (US Patent 5,062,021) it was proposed that the focused output of a low power laser with short pulse length could be used to generate the textured pattern. However, the patterned area typically required 75,000 textured spots that needed to be rapidly (less than 10 seconds) printed with good uniformity. A means to achieve the accurate placement and uniform profile, as well as a meaningfully rapid process time, was not discussed in the referenced patent. The LLNL team devised a system that could rapidly and inexpensively accomplish the texturing.

36 MATERIALS SCIENCE↗

X-ray Lasers: The evolution from Star Wars to the table-top [PowerPoint]

X-ray lasers have evolved from a Star Wars missile defense system to a table-top research tool: (1) LLNL proposes X-ray laser schemes in the 1970’s, (2) First X-ray lasers demonstrated in early 1980’s were nuclear pumped, (3) Demonstrated the world’s shortest wavelength, highest energy laser, (4) First laboratory X-ray laser demonstrated on Novette in 1984, (5) A decade of progress using the Nova laser (5 kJ) from 1985 to 1996, (6) X-ray lasers produced at the COMET table-top facility (<10 J) since 1997, (7) X-ray lasers used for plasma interferometry and other applications, (8) 10 Hz X-ray laser at 18.9 nm demonstrated in 2004 using 0.15 J drive, (9) 100 Hz X-ray laser at 13.9 nm produces 1 µJ of saturated output using 0.9 J drive from diode-pumped optical laser in 2014.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Solar power satellite system definition study. Volume 4: Silicon solar cell annealing test, phase 1

Laser annealing tests were conducted on ten 50 micron cells. Two were control cells that were not irradiated. These showed no loss in output due to exposure to the laser. Two cells were broken in handling. Six cells were successfully tested. All cells tested without breakage showed some recovery. One cell was subjected to two cycles and showed recovery on both cycles. Cells that were moderately degraded appeared to recover more completely than those more severly degraded. Exposure times ranged from two to ten seconds at 500 degrees centigrade. There was some indication that longer exposure was beneficial.

Walker, F.↗

Temperature Model of a New High-powered SrBr{sub 2} Laser

The radial temperature in the cross-section of a strontium copper bromide vapor laser is studied on the basis of a previously constructed mathematical model. The model has been expanded so as to allow for changes to the structural elements of the tube, in order to develop a new laser with an increased power output. The limits of the maximum allowed operating temperature of the gas have been established. The numerical results of the simulations have been presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characterization of a Nd:YAG doubled pulsed laser system

A description of a frequency doubled, double pulsed Nd:YAG laser that is to be used to pump an injection locked Ti:Sapphire power oscillator is presented. These two lasers make up the transmitter portion of the Lidar Atmospheric Sensing Experiment (LAWSE) instrument. LASE is a Lidar/DIAL experiment that is to measure water vapor in the troposphere. By utilizing the twin concept, both pulses can be produced with a single laser system, thereby minimizing cost, size, and weight. Alignment problems associated with having two separate lasers each produce one of the twin pulses are also alleviated. The LASE transmitter consists of a doubled pulsed Nd:YAG laser that will pump a Ti:Sapphire power oscillator that will be injection-locked by a diode laser. The wavelength of the Ti:Sapphire output will be tunable from 813 to 818 nm. A performance summary of the pump laser is given. The data verify that the pump laser can meet the performance requirements to pump the Ti:Sapphire power oscillator.

Williams-Byrd, Julie A.↗

High Efficiency Fiber-Coupled Diode Lasers for Resonant Pumping of Fiber Lasers

In this program, we have been developing high power, high efficiency laser diodes in InP, operating at 1532 nm and 1910 nm. These lasers have applications in resonant pumping eye-safe laser gain media, such as Erbium or Thulium doped fiber lasers, emitting in the ranges of 1600 nm and 1800-2000 nm, respectively. While such fiber lasers may be pumped with shorter wavelength diode lasers (e.g. 790 nm or 976 nm GaAs didoes), there are advantages to pumping with diode laser light that is closer in wavelength to the fiber laser emission, a technique known as resonant pumping. These advantages include lower quantum defect (the energy lost due to pump and emission at different wavelengths), increased eye-safety of system, decreased waste heat, and potential for lower overall system efficiency. We have achieved diode laser performance with peak electrical-to-optical (EO) efficiency of 39% at 15xx nm and 13% at 19xx nm, a significant advancement over current state-of-the-art. The rated output power and efficiency for these lasers are 4.0 W at 34% EO for 15xx nm, and 1.1 W at 11% EO for 19xx nm. We have designed and built a fiber-coupled-module at 15xx nm. There are many improvements to be made to increase the output power and efficiency of the module, but in our preliminary demonstration, we have achieved a fiber coupling efficiency of 85%.

99 GENERAL AND MISCELLANEOUS↗