Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Key Performance Indicator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Using SMAP Level-4 Soil Moisture to Constrain MOD16 Evapotranspiration over the Contiguous USA

Evapotranspiration (ET) is a key hydrologic variable linking the Earth’s water, carbon and energy cycles. At large spatial scales, remote sensing-based (RS) models are often used to quantify ET. Despite the large number of RS ET models available, few include soil moisture as a key environmental input, which can degrade model accuracy and utility. Here, we use model assimilation enhanced soil moisture estimates from the NASA SMAP (Soil Moisture Active Passive) mission as a water supply control in the MOD16 ET algorithm framework. SMAP-derived daily surface (0-5cm depth) and root zone (0-1m depth) soil moisture are used with MODIS (Moderate Resolution Imaging Spectroradiometer) vegetation observations, and 4km gridded regional surface meteorology (Gridmet) as primary inputs for estimating daily ET and underlying model soil and stomatal conductance terms. We calibrated the model environmental response parameters using tower eddy covariance ET observations representing major North American biomes. The model ET results were validated using a holdout set of tower observations spanning a large regional climate gradient. The updated ET estimates outperform the baseline MOD16 product across all tower validation sites (RMSE = 0.758 vs 1.108 mm day-1; R2 = 0.68 vs0.45, respectively). Smaller relative improvements were obtained using a recalibrated model with 4km Gridmet meteorology, but no soil moisture control (RMSE = 0.813 mm day-1; R2 = 0.66), indicating that these changes are essential for the improved model performance. The soil moisture-constrained model improvements and relative benefits from the SMAP observations are greater in arid climates, consistent with stronger soil moisture control on ET in water-limited regions. The use of SMAP soil moisture as an additional model constraint improves MOD16 regional performance and provides a new framework for investigating both soil and atmosphere controls on ET.

SMAP↗
DOE OSTI2023

Quantitative Analysis of Origin of Lithium Inventory Loss and Interface Evolution over Extended Fast Charge Aging in Li Ion Batteries

During the extreme fast charging (XFC) of lithium-ion batteries, lithium inventory loss (LLI) and reaction mechanisms at the anode/electrolyte interface are crucial factors in performance and safety. Determining the causes of LLI and quantifying them remain an essential challenge. We present mechanistic research on the evolution and interactions of aging mechanisms at the anode/electrolyte interface. We used NMC 532 /graphite pouch cells charged at rates of 1, 6, and 9 C up to 1000 cycles for our investigation. The cell components were characterized after cycling using electrochemical measurements, inductively coupled plasma optical emission spectroscopy, 7 Li solid-state nuclear magnetic resonance spectroscopy, and high-performance liquid chromatography/mass spectrometry. The results indicate that cells charged at 1 C exhibit no Li plating, and the increase of SEI thickness is the dominant source of the Li loss. In contrast, Li loss in cells charged at 9 C is related to the formation of the metallic plating layers (42%) the SEI layer (38.1%) and irreversible intercalation into the bulk graphite (19%). XPS analysis suggests that the charging rate has little influence on the evolution of SEI composition. The interactions between competing aging mechanisms were evaluated by a correlation analysis. In conclusion, the quantitative method established in this work provides a comprehensive analytical framework for understanding the synergistic coupling of anodic degradation mechanisms, forecasting SEI failure scenarios, and assessing the XFC lithium-ion battery capacity fade.

25 ENERGY STORAGE↗
NASA NTRS2015

Compatibility of the Radio Frequency Mass Gauge with Composite Tanks

The radio frequency mass gauge (RFMG) is a low-gravity propellant quantity gauge being developed at NASA for possible use in long-duration space missions utilizing cryogenic propellants. As part of the RFMG technology development process, we evaluated the compatibility of the RFMG with a graphite-epoxy composite material used to construct propellant tanks. The key material property that can affect compatibility with the RFMG is the electrical conductivity. Using samples of 8552IM7 graphite-epoxy composite, we characterized the resistivity and reflectivity over a range of frequencies. An RF impedance analyzer was used to characterize the out-of-plane electrical properties (along the sample thickness) in the frequency range 10 to 1800 MHZ. The resistivity value at 500 MHz was 4.8 ohm-cm. Microwave waveguide measurements of samples in the range 1.7 2.6 GHz, performed by inserting the samples into a WR-430 waveguide, showed reflectivity values above 98. Together, these results suggested that a tank constructed from graphite-epoxy composite would produce good quality electromagnetic tank modes, which is needed for the RFMG. This was verified by room-temperature measurements of the electromagnetic modes of a 2.4 m diameter tank constructed by Boeing from similar graphite-epoxy composite material. The quality factor Q of the tank electromagnetic modes, measured via RF reflection measurements from an antenna mounted in the tank, was typically in the range 400 Q 3000. The good quality modes observed in the tank indicate that the RFMG is compatible with graphite-epoxy tanks, and thus the RFMG could be used as a low-gravity propellant quantity gauge in such tanks filled with cryogenic propellants.

Radio frequencies↗
DOE OSTI2026

Production and Evaluation of Fluorophore-Doped Polymer Substrates to Screen for Plastic-Degrading Enzymes

Fast and sensitive analytical methods are the key to efficient screening of plastic-degrading enzymes. Here, we present a streamlined and affordable approach to assess the enzymatic deconstruction of insoluble synthetic polymers by blending them with a fluorescent dye, rhodamine 6G, and we evaluate this screening method using poly(ethylene terephthalate) (PET) as a model material. Our results indicate that enzymatic depolymerization of the rhodamine-doped PET can be observed in a high-throughput fashion by following release of the fluorophore. The fluorescence data obtained during the hydrolysis of rhodamine-doped PET by 14 PET hydrolases, produced with a robotic platform, correlated with the quantitative chromatographic analysis of PET degradation products. Remarkably, the use of the rhodamine-loaded PET substrate resulted in negligibly low background signals even when detecting PETase activity in crude cell lysates, suggesting suitability for screening of a wide variety of samples. Encouraged by these results, we next produced a selection of polyethylene- and nylon-based materials loaded with rhodamine 6G. While rapid leaching of fluorophore observed with nylon substrates limits the utility of the method for detecting nylonase activity, the rhodamine-loaded polyethylene showed promising performance in passive diffusion tests, indicating that this latter substrate may be used to screen for polyolefin-degrading enzymes.

09 BIOMASS FUELS↗
DOE OSTI2021

Strong Fermi-level pinning at metal contacts to halide perovskites

The performance of halide perovskite-based electronic and optoelectronic devices is often related to interfacial charge transport. To shed light on the underlying physical and chemical properties of CH 3 NH 3 PbI 3 (MAPbI 3 ) in direct contact with common electrodes Al, Ti, Cr, Ag, and Au, the evolution of interfacial properties and Fermi level pinning is systematically studied. Given a unique experimental facility, pristine interfaces without any exposure to ambient air were prepared. We observe aggregation of substantial amounts of metallic lead (Pb 0 ) at the metal/MAPbI 3 interface, resulting from the interfacial reaction between the deposited metal and iodine ions from MAPbI 3 . It is found that the Schottky barrier height at the metal/MAPbI 3 interface is independent of the metal work function due to strong Fermi level pinning, possibly due to the metallic Pb 0 aggregates, which act as interfacial trap sites. The charge neutrality level of MAPbI 3 is consistent with the energy level of Pb 0 -related defects, indicating that Pb 0 interfacial trap states can be nonradiative recombination sites. Here this work underlines that control of chemical bonding at interfaces is a key factor for designing future halide perovskite-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Dilute Source CO 2 Capture: Management of Atmospheric Coal-Produced Legacy Emissions (Final Technical Report)

This report presents the scientific and technical findings by Carbon Engineering Ltd (CE) resulting from the DOE sponsored research and development project on Direct Air Capture (DAC) process. The work was performed by CE under the Award DE-FE0026861 from the US Department of Energy’s (DOE) National Energy Technology Laboratory (NETL). The work plan was centered on advancing the Recipient’s DAC technology, developing a better understanding of its performance and cost. The report outlines the results from two key activities that were performed under this award: Studying the performance characteristics of the DAC plant at both pilot and lab scale Techno-economic analysis (TEA) to study two implementations of CE’s proprietary DAC process: i) An early commercial DAC process that captures ~1 MT CO 2 /year of atmospheric CO 2 (Baseline case), and ii) A modified early commercial DAC process that captures 1 MT CO 2 /year of flue gas CO 2 downstream of a subcritical PC post-CCS power plant (Case 1 Option C). Within the first key activity of the project, significant operational improvements and learnings were realized, including for key equipment in the DAC process in addition to the overall system. Learnings included impact of equipment design on the capture, calcination and slaking processes, and operational parameter modifications for optimizing the pelletization process, along with the complex interactions and associated considerations of these on overall system performance. In parallel, benchtop scale equipment was successfully utilized to validate pilot scale data, such as, retention in the pellet reactor, and capture performance parameters of the air contactor. CE continues to conduct core research and development activities; the learnings from this DOE project will contribute to the design, testing and operation activities of CE’s fully integrated DAC validation plant, as well as the first commercial DAC plant. The second key activity incorporated the above learnings, as well as input from vendors and EPC experts, to produce the TEA report. More specifically, the TEA results were based on measured pilot plant performance data for all major unit operations, and on an energy and material balance for the process at commercial scale computed using an Aspen One® process simulation. The cost estimation methodology follows AACE International recommended practices; with an uncertainty range of -15%/+30%. Depending on financial assumptions, energy costs, and the specific choice of inputs and outputs, the levelized cost per ton CO 2 captured from the atmosphere for an early commercial plant for the baseline case ranges from 227 to 304 $/t-CO 2 . And, the levelized cost to capture 98% of the flue gas CO 2 emissions in a subcritical PC power plant (Case 1 Option C) through a combination of Cansolv carbon capture system and a modified DAC system was estimated to range from 109 to 160 $/MWh of net power generated. Process improvement opportunities identified during this work, in addition to cost reduction opportunities identified during the Value Engineering exercise associated with the Baseline case indicate that significant reductions in capital costs are available as CE scales up and proceeds through deployment of initial facilities.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS2011

Miniature Sapphire Acoustic Resonator - MSAR

A room temperature sapphire acoustics resonator incorporated into an oscillator represents a possible opportunity to improve on quartz ultrastable oscillator (USO) performance, which has been a staple for NASA missions since the inception of spaceflight. Where quartz technology is very mature and shows a performance improvement of perhaps 1 dB/decade, these sapphire acoustic resonators when integrated with matured quartz electronics could achieve a frequency stability improvement of 10 dB or more. As quartz oscillators are an essential element of nearly all types of frequency standards and reference systems, the success of MSAR would advance the development of frequency standards and systems for both groundbased and flight-based projects. Current quartz oscillator technology is limited by quartz mechanical Q. With a possible improvement of more than x 10 Q with sapphire acoustic modes, the stability limit of current quartz oscillators may be improved tenfold, to 10(exp -14) at 1 second. The electromagnetic modes of sapphire that were previously developed at JPL require cryogenic temperatures to achieve the high Q levels needed to achieve this stability level. However sapphire fs acoustic modes, which have not been used before in a high-stability oscillator, indicate the required Q values (as high as Q = 10(exp 8)) may be achieved at room temperature in the kHz range. Even though sapphire is not piezoelectric, such a high Q should allow electrostatic excitation of the acoustic modes with a combination of DC and AC voltages across a small sapphire disk (approximately equal to l mm thick). The first evaluations under this task will test predictions of an estimated input impedance of 10 kilohms at Q = 10(exp 8), and explore the Q values that can be realized in a smaller resonator, which has not been previously tested for acoustic modes. This initial Q measurement and excitation demonstration can be viewed similar to a transducer converting electrical energy to mechanical energy and back. Such an electrostatic tweeter type excitation of a mechanical resonator will be tested at 5 MHz. Finite element calculation will be applied to resonator design for the desired resonator frequency and optimum configuration. The experiment consists of the sapphire resonator sandwiched between parallel electrodes. A DC+AC voltage can be applied to generate a force to act on a sapphire resonator. With the frequency of the AC voltage tuned to the sapphire resonator frequency, a resonant condition occurs and the sapphire Q can be measured with a high-frequency impedance analyzer. To achieve high Q values, many experimental factors such as vacuum seal, gas damping effects, charge buildup on the sapphire surface, heat dissipation, sapphire anchoring, and the sapphire mounting configuration will need attention. The effects of these parameters will be calculated and folded into the resonator design. It is envisioned that the initial test configuration would allow for movable electrodes to check gap spacing dependency and verify the input impedance prediction. Quartz oscillators are key components in nearly all ground- and space-based communication, tracking, and radio science applications. They play a key role as local oscillators for atomic frequency standards and serve as flywheel oscillators or to improve phase noise in high performance frequency and timing distribution systems. With ultra-stable performance from one to three seconds, an Earth-orbit or moon-based MSAR can enhance available performance options for spacecraft due to elimination of atmospheric path degradation.

Wang, Rabi T.↗
DOE OSTI2024

Optimal load attachment of a deeply embedded ring anchor in clay

A Deeply Embedded Ring Anchor (DERA) system has been developed as a cost-effective solution for mooring arrays of floating offshore wind turbines (FOWTs) to the seabed. The DERA boasts several key features, including its versatility in various soil types, compact size, compatibility with diverse mooring systems, multi-line potential, and robust performance even under unintentional loading conditions. While prior preliminary studies have provided valuable insights into how the DERA can enhance cost-effectiveness by offering a high load capacity, these studies have predominantly focused on optimizing anchor performance under translational horizontal and vertical loading. However, to design the DERA optimally, we must also consider its ability to handle inclined loading conditions in addition to lateral and axial loadings. Due to its shorter length compared to a conventional caisson, the DERA has less resistance to moments, making it more sensitive to horizontal load capacity and the optimal load attachment depth concerning load angle. For this reason, our study introduces an analytical approach to evaluate the effects of inclined loading on anchor performance, utilizing the previously validated upper bound plastic limit analysis (PLA) method. In investigating the optimal load attachment of the DERA, this paper conducts a parametric study to analyze how factors such as load attachment depth, anchor aspect ratio, and load inclination affect the DERA’s load capacity. Our findings indicate that PLA can serve as a valuable analytical tool for assessing the ultimate load capacity of the DERA, particularly under inclined loading conditions.

42 ENGINEERING↗
DOE OSTI2020

A Pilot-Scale Evaluation of Natural Gas-Based Foam at Elevated Pressure and Temperature Conditions

Abstract Nitrogen (N2) and Carbon Dioxide (CO2) foams have been used as hydraulic fracturing fluids for several decades to reduce water usage and minimize damage in water-sensitive reservoirs. These foam treatments require gases to be liquefied and transported to site. An alternative approach would be to use natural gas (NG) that is readily available from nearby wells, pipelines, and processing facilities as the internal, gaseous phase to create a NG-based foam. Hydraulic fracturing with NG foam is a relatively inexpensive option, makes use of an abundant and often wasted resource, and may even provide production benefits in certain reservoirs. As part of an ongoing development project sponsored by the Department of Energy (DOE), the surface process to create NG foam is being developed and the properties of NG foam are being explored. This paper presents recent results from a rigorous pilot-scale demonstration of NG foam over a range of operating scenarios relevant to surface and bottomhole conditions with a variety of base-fluid mixtures. The Pilot-scale Foam Test Facility (PFTF) used in these investigations is first described. The PFTF is capable of generating foamed fluids at pressures up to 7,500 psig and at temperatures in excess of 300°F. Then, results from several investigations aimed at proving NG foam at conditions relevant to the field are presented. NG foam was characterized using rheology measurements and flow visualization techniques. Experiments were performed to investigate the texture and stability of NG foam generated by two different mixing methods: one using a custom designed tee to match mixing velocities in the field where the gas phase is jetted into the aqueous stream, and another to ensure comprehensive mixing for laboratory analysis. Parametric studies were conducted to explore the effects of flow rate, foam quality, and temperature on the stability of NG foam. Moreover, different fluid preparations were used to investigate the effect of base fluid and additive concentrations on the stability of NG foams. Additional laboratory studies that investigated foam stability with produced water and multicomponent NG mixtures are also reported. The NG foams explored in these investigations exhibited typical, shear-thinning behavior observed in rheological studies of N2- and CO2-based foams. The measured viscosity and observed stability indicate that NG foams are well suited for fracturing applications. Like other foams, NG foam exhibits sensitivity to operating temperature characterized by a decrease in apparent viscosity as temperature increases. Rapid foam breakdown was observed at significantly elevated temperatures exceeding 290°F. In addition to fluid characterization, these investigations also yielded several key lessons that should be applied to future field demonstrations of NG foam.

Beck, Griffin↗
DOE OSTI2023

Performance Assessment for the Disposal of Low-Level Waste in the 200 West Area Burial Grounds (Annual Status Report FY 2022)

This annual review provides the projected dose estimates of radionuclide inventories disposed in the active 200 West Area Low-Level Waste Burial Grounds (LLBGs) since September 26, 1988. These estimates are calculated using the original dose methodology developed in the performance assessment (PA) analysis (WHC-EP-0645). The estimates are compared with the performance objectives defined in U.S. Department of Energy requirements (DOE O 435.1 and its companion documents DOE M 435.1-1 and DOE-STD-5002-2017). All performance objectives are currently satisfied, and operational waste acceptance criteria (HNF-EP-0063) and waste acceptance practices continue to be sufficient to maintain compliance with performance objectives. Inventory estimates and associated dose estimates from future waste disposal actions are unchanged from previous years’ evaluations that indicate potential impacts well below performance objectives; therefore, future compliance with DOE O 435.1 is expected. Within the active burial grounds, low-level and mixed low-level waste currently may be disposed only in two lined trenches in the 218-W-5 Burial Ground (Trenches 31 and 34) until they are either filled or a decision is made to close these trenches. Some mixed low-level waste is also disposed at the Environmental Restoration Disposal Facility in the 200 West Area (which is covered under a separate PA). During this (fiscal year 2022) reporting period (October 1, 2021, through September 30, 2022), waste was disposed to the 200 West Area LLBGs. Continued groundwater monitoring of the 200 West Area LLBGs indicates no groundwater contamination due to LLBG waste. Current assumptions about future land use at the Hanford Site are consistent with PA analysis assumptions of a postclosure facility that will not be degraded by human activity. The LLBGs are in an area identified for waste management and containment of residual contamination (DOE/EIS-0391). The current closure plan for the LLBGs (DOE/RL-2000-70) estimates that the 200 West LLBGs will be closed in the 2050 timeframe. The Disposal Authorization Statement, other technical basis documents, and the radioactive waste management basis are of continued adequacy to meet the performance objectives of DOE O 435.1. Overall, there are no substantive changes to primary PA assumptions and no changes to the PA analysis conclusion; therefore, compliance with DOE O 435.1 and the Disposal Authorization Statement is maintained. A new PA to evaluate the long-term impacts of three disposal trenches that are currently active within the 200 East and 200 West Areas (Trench 94 in the 200 East Area and Trenches 31 and 34 in the 200 West Area) was initiated in fiscal year 2019 and completed in fiscal year 2022. Corrective actions addressing 3 key issues and 31 secondary issues identified during the review process were developed and submitted to the Low-Level Waste Disposal Facility Federal Review Group Co-Chairs for review and approval. This PA provides additional technical basis for the continued adequacy of the existing Operating Disposal Authorization Statement.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2015

Compatibility of the Radio Frequency Mass Gauge with Graphite-Epoxy Composite Tanks

The radio frequency mass gauge (RFMG) is a low-gravity propellant quantity gauge being developed at NASA for possible use in long-duration space missions utilizing cryogenic propellants. As part of the RFMG technology development process, we evaluated the compatibility of the RFMG with a graphite-epoxy composite material used to construct propellant tanks. The key material property that can affect compatibility with the RFMG is the electrical conductivity. Using samples of 8552/IM7 graphite-epoxy composite, we characterized the resistivity and reflectivity over a range of frequencies. An RF impedance analyzer was used to characterize the out-of-plane electrical properties (along the sample thickness) in the frequency range 10 to 1800 MHZ. The resistivity value at 500 MHz was 4.8 ohm-cm. Microwave waveguide measurements of samples in the range 1.7 - 2.6 GHz, performed by inserting the samples into a WR-430 waveguide, showed reflectivity values above 98%. Together, these results suggested that a tank constructed from graphite/epoxy composite would produce good quality electromagnetic tank modes, which is needed for the RFMG. This was verified by room-temperature measurements of the electromagnetic modes of a 2.4 m diameter tank constructed by Boeing from similar graphite-epoxy composite material. The quality factor Q of the tank electromagnetic modes, measured via RF reflection measurements from an antenna mounted in the tank, was typically in the range 400 less than Q less than 3000. The good quality modes observed in the tank indicate that the RFMG is compatible with graphite-epoxy tanks, and thus the RFMG could be used as a low-gravity propellant quantity gauge in such tanks filled with cryogenic propellants.

Propellant tanks↗
DOE OSTI2024

A hierarchal model for bacterial cell inactivation in solution by direct and indirect treatment using cold atmospheric plasmas

Cold atmospheric plasma devices have shown promise for a variety of plasma medical applications, including wound healing and bacterial inactivation often performed in liquids. In the latter application, plasma-produced reactive oxygen and nitrogen species (RONS) interact with and damage bacterial cells, though the exact mechanism by which cell damage occurs is unclear. Computational models can help elucidate relationships between plasma-produced RONS and cell killing by enabling direct comparison between dissimilar plasma devices and by examining the effects of changing operating parameters in these devices. In biological applications, computational models of plasma-liquid interactions would be most effective in design and optimization of plasma devices if there is a corresponding prediction of the biological outcome. In this work, we propose a hierarchal model for planktonic bacterial cell inactivation by plasma produced RONS in liquid. A previously developed reaction mechanism for plasma induced modification of cysteine was extended to provide a basis for cell killing by plasma-produced RONS. Results from the model are compared to literature values to provide proof of concept. Differences in time to bacterial inactivation as a function of plasma operating parameters including gas composition and plasma source configuration are discussed. Results indicate that optimizing gas-phase reactive nitrogen species production may be key in the design of plasma devices for disinfection.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Enhanced phagocytosis and complement-mediated killing of Mannheimia haemolytica serotype 1 following in-frame CMP-sialic acid synthetase ( neuA ) gene deletion

ABSTRACT Mannheimia haemolyticais the most significant bacterial pathogen associated with the bovine respiratory disease complex. Although sialic acid is a known virulence factor in other members of Pasteurellaceae, such asHistophilus somniandPasteurella multocida, the significance of sialic acid to the virulence ofM. haemolyticais currently unknown. Therefore, the role of sialic acid as a virulence determinant ofM. haemolyticawas investigated by constructing an in-frameneuA[CMP-N-acetylneuraminic acid (Neu5Ac/sialic) synthetase] mutant, which was shown by high-performance anion exchange chromatographic analysis (HPAEC) to be devoid of sialic acid on the lipopolysaccharide (LPS). Both theneuAmutant and wild-type parent strains exhibited similar growth rates in the growth curve assay. Real-time qPCR and ELISA evaluation showed no differences in proinflammatory cytokine expressions (IL-1β, IL-6, and IL-8) between theneuAmutant and parent strain when peripheral blood mononuclear cells were incubated with LPS. Interestingly, theneuAmutant was three to four logs more sensitive to a whole-blood bacterial killing assay than the parent strain. Similar results were also observed in plasma and serum bacterial killing assays. Flow cytometry analyses showed higher uptake ofneuAmutant by phagocytes, compared to the parent strain, in the whole-blood phagocytosis assay; however, no difference in reactive oxygen species production in neutrophils or monocytes was detected for either strain. Taken together, these results indicate that sialylation ofM. haemolyticaLPS plays a vital role in reducing complement-mediated and phagocytic killing. IMPORTANCE The Gram-negative coccobacillusMannheimia haemolyticais a natural inhabitant of the upper respiratory tract in ruminants and the most common bacterial agent involved in bovine respiratory disease complex development. Key virulence factors harbored byM. haemolyticaare leukotoxin, lipopolysaccharide, capsule, adhesins, and neuraminidase which are involved in evading innate and adaptive immune responses. In this study, we have shown that CMP-sialic acid synthetase (neuA) is necessary for the incorporation of sialic acid onto the membrane, and inactivation ofneuAresults in increased phagocytosis and complement-mediated killing ofM. haemolytica,thus demonstrating that sialylation contributes to the virulence ofM. haemolytica.

Microbiology↗
DOE OSTI2023

Stability of Cu(In x Ga 1− x )Se 2 Solar Cells Utilizing RbF Postdeposition Treatment under a Sulfur Atmosphere

Alkali halide postdeposition treatments (PDTs) have become a key tool to maximize efficiency in Cu(In x Ga 1− x )Se 2 (CIGS) photovoltaics. RbF PDTs have emerged as an alternative to the more common Na‐ and K‐based techniques. This study utilizes temperature‐dependent current–voltage ( JVT ) measurements to study a unique RbF PDT performed in a S atmosphere. The samples are measured before and after 6 months in a desiccator to study device stability. Both samples contain Na and K which diffuse from the soda–lime glass substrate. A reference sample and a RbF + S PDT sample both show the development of a rear contact barrier after aging. The contact barrier is higher for the RbF + S PDT sample, leading to decreased current in forward bias. Series resistance is also higher in the RbF + S PDT device which leads to lower fill factor. However, after aging the reference sample has a larger decrease in open‐circuit voltage ( V OC ). Ideality factor measurements suggest Shockley–Read–Hall recombination dominates both samples. V OC versus temperature and a temperature‐dependent activation energy model are used to calculate diode activation energies for each sample condition. Both techniques produce similar values that indicate recombination primarily occurs within the bulk absorber.

14 SOLAR ENERGY↗
DOE OSTI2021

Evaluation of Triage Methods for Criticality Accidents

Studies indicate that early identification of persons involved in and receiving high doses of radiation in accidents is key to providing life-saving medical treatment. Although the risk of criticality accidents is low the potential impact to workers is significant. For facilities that employ large numbers of workers a key element in the response to a radiological emergency is identifying personnel that received significant, and potentially harmful, doses. Also important is having the ability to screen large numbers of workers to identify persons that did not receive significant exposure so as to reduce the impact on emergency response efforts. At the Y-12 National Security Complex the focus on criticality accident response is the rapid triage of personnel in order to identify persons exposed to large radiation doses and to prioritize those persons receiving the highest exposures. Once identified personnel are transported to local medical facilities including the Radiation Emergency Assistance Center/Training Site (REAC/TS) for medical evaluation and treatment. The Y-12 external dosimetry program utilizes a number of techniques to identify and prioritize workers and these methods were evaluated at a criticality dosimetry intercomparison exercise. Finally, the methods used were shown to perform as intended and other sites may consider incorporating these methods into their accident dosimetry response procedures.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2026

BSMV-mediated genome editing exhibits host-specific heritability: germline transmission in barley and somatic edits in Nicotiana benthamiana

Plant RNA virus–mediated guide RNA (gRNA) delivery represents a transformative advance in genome editing technologies. Unlike conventional transformation methods that rely on labor-intensive tissue culture and regeneration for each individual gRNA delivery, viral vectors can rapidly and systemically transmit gRNAs into pre-established Cas-expressing plants, providing an accelerated route for functional genomics and trait discovery directly in planta . However, key design parameters, including subgenomic promoter choice, transcript architecture, and their effects on viral fitness and editing outcomes, remain to be elucidated for most viral platforms. We developed five Barley stripe mosaic virus (BSMV) vectors, each with distinct subgenomic promoter elements to drive single gRNA expression. These were initially evaluated in Cas9-expressing transgenic Nicotiana benthamiana plants targeting the Phytoene desaturase ( PDS ) gene to compare their editing efficiencies. Single gRNAs expressed under the duplicated γb subgenomic promoter or when fused directly to the γb genome achieved the highest mutation frequencies (up to 90% at 60 days post-inoculation), whereas β1- and β2-driven sgRNAs produced delayed and reduced editing. Thus, promoter selection critically determines gRNA accumulation and the efficacy of BSMV-mediated genome editing. The top-performing design was then applied to Cas9-expressing barley ( Hordeum vulgare ) targeting HvCMF7 (conferring green-white variegation) and HvGW2.1 (impacts grain width and weight). BSMV spread systemically throughout barley, inducing somatic and heritable mutations at frequencies up to 100%, with virus-free edited progeny. In contrast, despite robust somatic editing in N. benthamiana, no heritable mutations were detected indicating species-dependent limitations in germline transmission. Our systematic comparison of subgenomic promoter architectures establishes clear design principles for optimizing viral vector–mediated delivery. Promoter choice and transcript structure critically shape editing efficiency and viral stability. The host-specific boundary for germline editing, defined by efficient heritable editing in barley but not N. benthamiana , highlights where BSMV offers advantages and where alternative vectors or hybrid strategies are required, guiding rational platform selection for diverse crop species and applications. Collectively, these findings establish BSMV as a promising next-generation vector for rapid, tissue culture–free, and transformation-independent genome editing in cereals and other recalcitrant monocots.

barley↗
NASA NTRS2009

Evaluating the Impact of Land Use Change on Submerged Aquatic Vegetation Stressors in Mobile Bay

Alabama coastal systems have been subjected to increasing pressure from a variety of activities including urban and rural development, shoreline modifications, industrial activities, and dredging of shipping and navigation channels. The impacts on coastal ecosystems are often observed through the use of indicator species. One such indicator species for aquatic ecosystem health is submerged aquatic vegetation (SAV). Watershed and hydrodynamic modeling has been performed to evaluate the impact of land use change in Mobile and Baldwin counties on SAV stressors and controlling factors (temperature, salinity, and sediment) in Mobile Bay. Watershed modeling using the Loading Simulation Package in C++ (LSPC) was performed for all watersheds contiguous to Mobile Bay for land use scenarios in 1948, 1992, 2001, and 2030. Landsat-derived National Land Cover Data (NLCD) were used in the 1992 and 2001 simulations after having been reclassified to a common classification scheme. The Prescott Spatial Growth Model was used to project the 2030 land use scenario based on current trends. The LSPC model simulations provided output on changes in flow, temperature, and sediment for 22 discharge points into the Bay. Theses results were inputted in the Environmental Fluid Dynamics Computer Code (EFDC) hydrodynamic model to generate data on changes in temperature, salinity, and sediment on a grid with four vertical profiles throughout Mobile Bay. The changes in the aquatic ecosystem were used to perform an ecological analysis to evaluate the impact on SAV habitat suitability. This is the key product benefiting the Mobile Bay coastal environmental managers that integrates the influences of temperature, salinity, and sediment due to land use driven flow changes with the restoration potential of SAVs.

Al-Hamdan, Mohammad↗
DOE OSTI2023

Observing the onset of the accretion wake in Vela X-1

High-mass X-ray binaries (HMXBs) offer a unique opportunity to investigate accretion onto compact objects and the wind structure in massive stars. A key source for such studies is the bright neutron star HMXB Vela X-1 whose convenient physical and orbital parameters facilitate analyses and in particular enable studies of the wind structure in HMXBs. Here, we analyse simultaneous XMM-Newton and NuSTAR observations at $\phi_{orb}$ ≈ 0.36–0.52 and perform time-resolved spectral analysis down to the pulse period of the neutron star based on our previous NuSTAR-only results. For the first time, we are able to trace the onset of the wakes in a broad 0.5–78 keV range with a high-time resolution of ~283 s and compare our results with theoretical predictions. Here we observed a clear rise in the absorption column density of the stellar wind N H,1 starting at orbital phase ~0.44, corresponding to the wake structure entering our line of sight towards the neutron star, together with local extrema throughout the observation, which are possibly associated with clumps or other structures in the wind. Periods of high absorption reveal the presence of multiple fluorescent emission lines of highly ionised species, mainly in the soft-X-ray band between 0.5 and 4 keV, indicating photoionisation of the wind.

79 ASTRONOMY AND ASTROPHYSICS↗