Influence of surface parameters on anode losses in arcjets
Surface parameters influence on energy transfer to arc jet anode, discussing work function, accommodation coefficient and diffuse reflection coefficient of electrons
Hassan, H. A.↗
SEARCH · Engineering Papers
Results for “Jet Surface”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Externally blown flap dynamic loads
Some of the principal results obtained in three series of measurements of fluctuating surface pressures induced on externally blown flaps by jet impingment are presented. Large- and small-scale models and hot- and cold-flow tests are considered. The discussion sets forth scaling parameters and consistent features of the root-mean-square values and spectra of the loading. Implications of these results with regard to sonic fatigue are indicated.
Lansing, D. L.↗
Fluctuating pressures on aircraft wing and flap surfaces associated with powered-lift systems
The present work presents results from two research studies that provide information on the fluctuating pressures generated by the use of powered-lift systems in STOL aircraft. Data are given for several chordwise and spanwise locations on large-scale models of an externally blown flap (EBF) configuration and an upper surface blown flap (USB) configuration in which actual jet engines were used. Pressure levels were high enough to indicate that special design effort will be required to avoid acoustic fatigue failures of wing and flap sturctures. The observation that pressure levels did not decrease very much with increased distance from the engine exhaust center line suggests that a STOL aircraft fuselage, which is in relatively close proximity to the engines for aerodynamic reasons, will be subjected to unusually high external overall fluctuating pressure levels (OAFPLs) that may cause difficulty in control of the cabin noise level.
Mixson, J. S.↗
STOL aircraft transient ground effects. Part 2: Experimental techniques feasibility study
Procedures for simulating transient effects associated with STOL aircraft landings and takeoffs were examined and a basis was developed for selection of an experimental approach based on consideration of simulation requirements, experimental techniques, facilities, and costs. The results are generally applicable to STOL aircraft employing any of the following powered lift systems: externally blown flap, upper surface blown flap, augmentor wing, or internally ducted jet flap. Scaling relationships were developed to apply the simulation requirements to model test situations. Procedures for the derivation of aerodynamic forces from the measured data were discussed. Various means of expressing the aerodynamic data in forms convenient for use in performance or stability and control applications were described. Five different experimental techniques were presented that depend on two different types of experimental facilities, wind tunnels and test tracks, and involving different types of model motion, and factors pertinent to selection were summarized.
Crowder, J. P.↗
Publications in acoustics and noise control from the NASA Langley Research Center during 1940 - 1974
This document contains reference lists of published Langley Research Center papers in various areas of acoustics and noise control for the period 1940-1974. The research work was performed either in-house by the center staff or by other personnel supported entirely or in part by grants or contracts. The references are listed chronologically and are grouped under the following general headings: (1) Duct acoustics, (2) Propagation and operations, (3) Rotating blade noise, (4) Jet noise, (5) Sonic boom, (6) Flow-surface interaction noise, (7) Human response, and (8) Structural response.
Smith, G. C.↗
Publications in acoustics and noise control from the NASA Langley Research Center during 1940-1976
Reference lists are presented of published research papers in various areas of acoustics and noise control for the period 1940-1976. The references are listed chronologically and are grouped under the following general headings: (1) Duct acoustics; (2) propagation and operations; (3) rotating blade noise; (4) jet noise; (5) sonic boom; (6) flow-surface interaction noise; (7) human response; (8) structural response; (9) prediction; and (10) miscellaneous.
Fryer, B. A.↗
Computation of transonic boattail flow with separation
The relaxation procedure of South and Jameson for the full potential transonic flow equation was coupled to a modified Reshotko-Tucker integral boundary-layer technique with an empirical model for separated flow. The viscous and inviscid flows were solved iteratively until convergence was obtained. This iterative method was then applied to the subsonic and transonic flow over a series of axisymmetric circular-arc boattails with solid jet plume simulators. Comparisons of theoretical and experimental surface pressures and boattail drag are presented over a free-stream Mach numbers below 0.90. The qualitative variation of boattail drag with free-stream Mach number and boattail angle well into the region of transonic drag rise was correctly predicted; however, the absolute drag levels were significantly underpredicted. For separated flows, the empirical discriminating streamline model gives good results up to a free-stream Mach number of about 0.90 and allows reasonable predictions for shock-induced separation if the proper separation location and separation turning angle are known.
Wilmoth, R. G.↗
Dust adhesion on Viking lander camera window
Studies of dust impingement on a duplicate Viking Lander camera window indicated the possibility of window obscuration after several days of exposure even at low dust concentration levels. As a result the following corrective measures were recommended: (1) The clearance between the housing surface and the camera post should be eliminated by using an appropriately designed plastic skirt: (2) The three horizontal ledges below the window inside the cavity act as bases for pile-up of dust that slides down the window surface; they should be replaced by a single inclined plane down which the dust will slide and fall out on the ground: (3) Adhered dust on the window surface can be removed by high pressure CO2 jets directed down against the window; the amount of CO2 gas needed for the entire mission can be carried in a 3 1/2-inch diameter sphere equipped with a remotely programable valve. These measures were incorporated in the design of the lander camera system. The continued high quality of photographs transmitted from the Viking spacecraft several months after landing attests to their effectiveness.
Singh, J. J.↗
Longitudinal aerodynamic characteristics of a wing-winglet model designed at M = 0.8, C sub L = 0.4 using linear aerodynamic theory
Wind tunnel test results have been presented herein for a subsonic transport type wing fitted with winglets. Wind planform was chosen to be representative of wings used on current jet transport aircraft, while wing and winglet camber surfaces were designed using two different linear aerodynamic design methods. The purpose of the wind tunnel investigation was to determine the effectiveness of these linear aerodynamic design computer codes in designing a non-planar transport configuration which would cruise efficiently. The design lift coefficient was chosen to be 0.4, at a design Mach number of 0.8. Force and limited pressure data were obtained for the basic wing, and for the wing fitted with the two different winglet designs, at Mach numbers of 0.60, 0.70, 0.75 and 0.80 over an angle of attack range of -2 to +6 degrees, at zero sideslip. The data have been presented without analysis to expedite publication.
Kuhlman, J. M.↗
First Halley multicolour camera imaging results from Giotto
The Giotto spacecraft's Halley Multicolor Camera imaging results have furnished flyby images that are centered on the brightest part of the inner coma; these show the silouette of a large, solid and irregularly shaped cometary nucleus and jetlike dust activity. The preliminary assessment of these data has yielded information on the dimensions and shape of the nucleus and dust emission activity. It is noted that only minor parts of the surface are active, with most of the surface being covered by a nonvolatile material. Dust jets dominate the inner coma, and are restricted to a subsolar hemisphere.
Keller, H. U.↗
A kinetic study of hydrous alteration of amorphous MgSiO smokes - Implications for cometary particles and chondrite matrix
Measurements of the rate of hydrous alteration of amorphous Mg-SiO smokes are reported as a function of temperature, as inferred by observing changes in the infrared spectra of these materials. It is shown that under the conditions reported for the nucleus of Comet Halley, based on measurements made by the Vega and Giotto missions, amorphous, anhydrous Mg-SiO smokes would become hydrated within several weeks in the dusty regolith observed on the surface. However, if such grains were released in 'jets' or from loose ice fragments, then previously amorphous grains would retain their anhydrous nature. Similarly, brief periods of aqueous activity on meteorite parent bodies would convert amorphous, fine-grained material to hydrated phyllosilicates much more rapidly than coarse mineral grains. A kinetic model might therefore be developed to explain the observed textural relationships in the matrices of carbonaceous chondrites such as Mokoia, where amorphous phyllosilicates are intimately associated with coarse anhydrous grains.
Nelson, Robert↗
Effects of very high turbulence on heat transfer
The effects of very high free stream turbulence on heat transfer were investigated experimentally by placing a flat plate, constant temperature heat transfer surface in a large diameter turbulent-free jet. The heat transfer rates measured were two to four times greater than those that would be predicted by accepted correlations for turbulent boundary layers. Thus, rather than establish a particular high turbulence flow field and then measure its effect on heat transfer, search for a flow field with very aggressive heat transfer characteristics and description of the aspects of the free stream turbulence associated with high levels of heat transfer is examined.
Maciejewski, Paul K.↗
Liquid jet breakup and atomization in rocket chambers under dense spray conditions
Two advanced diagnostic techniques were established and employed in this project. The first technique involves the use of a real-time x ray radiography system along with a high-speed CCD Xybion camera and an advanced digital image processor to investigate the breakup processes of the liquid core. The focus of this part of the project is to determine the inner structure of the liquid jet and via thin sheets of laser light, with the scatters light being photographed by a Xybion electronic camera synchronized to the laser pulse. This technique, which is capable of recording the breakup event occurring within 25 nano-seconds, enables us to freeze the motions of the jet and liquid droplets. The focus of this part of the project is to determine the outer structure of the liquid jet and to discover the configuration of the surface waves, the spray pattern, and the droplet size distribution in the non-dilute region. Results obtained by these two advanced diagnostic techniques will provide the much needed database for model development and accurate prediction of engine performance. The present work also represents a breakthrough in the area of advanced diagnostics of dense sprays.
Kuo, Kenneth K.↗
Aerodynamic control using forebody blowing and suction
Aerodynamic control using pneumatic forebody flow control was studied. Three methods of control were investigated: (1) blowing from a localized jet, (2) blowing from a slot, and (3) surface suction. Flow visualization and yawing moment measurements were performed on F/A-18 models in a water tunnel. The results show that all the methods were effective in controlling the forebody flow over a wide range of angles of attack and sideslip. The advantages and limitations of each of the control methods were discussed. The experiments suggested that all the control methods work basically on the principle of separation control. Based on the results of the water tunnel tests, the blowing or suction mass flow requirements appear to be within the limits of typical engine-bleed available from a modern fighter engine.
Ng, T. Terry↗
Impact of aeroelasticity on propulsion and longitudinal flight dynamics of an air-breathing hypersonic vehicle
Many air-breathing hypersonic aerospacecraft design concepts incorporate an elongated fuselage forebody acting as the aerodynamic compression surface for a hypersonic combustion module, or scram jet. This highly integrated design approach creates the potential for an unprecedented form of aero-propulsive-elastic interaction in which deflections of the vehicle fuselage give rise to propulsion transients, producing force and moment variations that may adversely impact the rigid body flight dynamics and/or further excite the fuselage bending modes. To investigate the potential for such interactions, a math model was developed which included the longitudinal flight dynamics, propulsion system, and first seven elastic modes of a hypersonic air-breathing vehicle. Perturbation time histories from a simulation incorporating this math model are presented that quantify the propulsive force and moment variations resulting from aeroelastic vehicle deflections. Root locus plots are presented to illustrate the effect of feeding the propulsive perturbations back into the aeroelastic model. A concluding section summarizes the implications of the observed effects for highly integrated hypersonic air-breathing vehicle concepts.
Raney, David L.↗
Sensitivity of blackbody reference panels to wind blast
As part of the effort at Stennis and JPL to discover the root causes of Thermal Infrared Multispectral Scanner's (TIMS') temperature calibration errors, a series of experiments were performed to measure the sensitivity of a heated plate to cooling by wind blast. A powerful blower which was capable of generating a jet of wind in excess of 200 miles per hour was set up. In the jet, an electrically heated copper plate, one quarter of an inch thick and six inches square, was mounted. The electrical heaters were capable of delivering a total power of 800 watts. The power to the heaters was feedback controlled with reference to a thermistor mounted on the back of the copper plate. The plate was mounted about 2.5 feet from the blower nozzle, at about 45 deg to the direction of the jet. The jet was wide enough to wash the whole surface and its temperature at the plate was about 28 C.
Hoover, Gordon↗
A wind tunnel investigation of the effects of micro-vortex generators and Gurney flaps on the high-lift characteristics of a business jet wing
A study of a full-scale, semi-span business jet wing has been conducted to investigate the potential of two types of high-lift devices for improving aircraft high-lift performance. The research effort involved low-speed wind-tunnel tests of micro-vortex generators and Gurney flaps applied to the flap system of the business jet wing and included force and moment measurements, surface pressure surveys and flow visualization on the wing and flap. Results showed that the micro-vortex generators tested had no beneficial effects on the longitudinal force characteristics in this particular application, while the Gurney flaps were an effective means of increasing lift. However, the Gurney flaps also caused an increase in drag in most circumstances.
Martuccio, Michelle Therese↗
Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel
A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.
Hunton, Lynn W.↗