Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ISOTHERMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Transient liquid-crystal technique used to produce high-resolution convective heat-transfer-coefficient maps

In this transient technique the preheated isothermal model wall simulates the classic one-dimensional, semi-infinite wall heat transfer conduction problem. By knowing the temperature of the air flowing through the model, the initial temperature of the model wall, and the surface cooling rate measured at any location with time (using the fast-response liquid-crystal patterns recorded on video tape), the heat transfer coefficient can be calculated for the color isothermal pattern produced. Although the test was run transiently, the heat transfer coefficients are for the steady-state case. The upstream thermal boundary condition was considered to be isothermal. This transient liquid-crystal heat-transfer technique was used in a transient air tunnel in which a square-inlet, 3-to-1 exit transition duct was placed. The duct was preheated prior to allowing room temperature air to be suddenly drawn through it. The resulting isothermal contours on the duct surfaces were revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record was made of the temperature and time data for all points on the duct surfaces during each test. The duct surfaces were uniformly heated using two heating systems: the first was an automatic temperature-controlled heater blanket completely surrounding the test duct like an oven, and the second was an internal hot-air loop through the inside of the test duct. The hot-air loop path was confined inside the test duct by insulated heat dams located at the inlet and exit ends of the test duct. A recirculating fan moved hot air into the duct inlet, through the duct, out of the duct exit, through the oven, and back to the duct inlet. The temperature nonuniformity of the test duct model wall was held very small. Test results are reported for two inlet Reynolds numbers of 200,000 and 1,150,000 (based on the square-inlet hydraulic diameter) and two free-stream turbulence intensities of about 1 percent, which is typical of wind tunnels, and up to 20 percent (using a grid), which is typical of real engine conditions.

Hippensteele, Steven A.↗

An overview of elevated temperature damage mechanisms and fatigue behavior of a unidirectional SCS-6/Ti-15-3 composite

The fatigue behavior of a unidirectionally reinforced titanium matrix composite (TMC), SiC/Ti-15-3, was thoroughly characterized to support life prediction modeling of advanced TMC disks designed for gas turbine engine applications. The results of this coupon-level experimental investigation are reviewed. On a stress basis, the isothermal fatigue behavior of the (0 deg) TMC revealed significant improvements over the unreinforced matrix. In contrast, the (90 deg) TMC exhibited degraded properties and lives for similar comparisons. This was attributed to the weak fiber/matrix interfacial bond. Encasing the (0 deg) TMC with a Ti-15-3 case did not affect isothermal fatigue lives at higher strain levels. However, at lower strain levels, rapid initiation and propagation of large fatigue cracks in the case degraded the fatigue lives. Thermomechanical fatigue (TMF) lives were significantly reduced for the (0 deg) TMC when compared to isothermal lives. At high strains, in-phase TMF produced extremely short lives. This degradation was attributed to fiber overload failures brought about by stress relaxation in the matrix. At low strains, out-of-phase TMF conditions became life limiting. Environment-assisted surface cracking was found to accelerate fatigue failure. This produced extensive matrix damage with minimal fiber damage. For the (90 deg) TMC, TMF conditions did not promote an additional degradation in cyclic life beyond that observed under isothermal conditions.

Castelli, Michael G.↗

The effects of a hot outer atmosphere on acoustic-gravity waves

We examine the effects of a hot chromosphere and corona on acoustic-gravity waves in the Sun. We use a simple solar model consisting of a neutrally stable polytrope smoothly matched to an isothermal chromosphere or corona. The temperature of the isothermal region is higher than the minimum temperature of the model. We ignore sphericity, magnetic fields, changes in the gravitational potential, and nonadiabatic effects. We find a family of atmospheric g-modes whose cavity is formed by the extremum in the buoyancy frequency at the transition region. The f-mode is the zero-order member of this family. For large values of the harmonic degree l, f-mode frequencies are below the classic f-mode frequency, mu=(gk)(exp 1/2), whereas at small values of l, the f-mode is identical to the classical f-mode solution. We also find a family of g-modes residing in the low chromosphere. Frequency shifts of p-modes can be positive or negative. When the frequency is less than the acoustic cutoff frequency of the upper isothermal atmsophere, the frequency of the upper isothermal atmosphere, the frequency shift is negative, but when the frequency is above this cutoff, the shifts can be positive. High-frequency acoustic waves which are not reflected by the photospheric cutoff are reflected at the corona by the high sound speed for moderate values of l and v. This result is independent of the solar model as long as the corona is very hot. The data are inconsistent with this result, and reasons for this discrepancy are discussed.

Hindman, Bradley W.↗

Protostellar Collapse with a Shock

We reexamine both numerically and analytically the collapse of the singular isothermal sphere in the context of low-mass star formation. We consider the case where the onset of collapse is initiated by some arbitrary process which is accompanied by a central output of either heat or kinetic energy. We find two classes of numerical solutions describing this manner of collapse. The first approaches in time the expansion wave solution of Shu, while the second class is characterized by an ever-decreasing central accretion rate and the presence of an outwardly propagating weak shock. The collapse solution which represents the dividing case between these two classes is determined analytically by a similarity analysis. This solution shares with the expansion wave solution the properties that the gas remains stationary with an r(exp -2) density profile at large radius and that, at small radius, the gas free-falls onto a nascent core at a constant rate which depends only on the isothermal sound speed. This accretion rate is a factor of approx. 0.1 that predicted by the expansion wave solution. This reduction is due in part to the presence of a weak shock which propagates outward at 1.26 times the sound speed. Gas in the postshock region first moves out subsonically but is then decelerated and begins to collapse. The existence of two classes of numerical collapse solutions is explained in terms of the instability to radial perturbations of the analytic solution. Collapse occurring in the manner described by some of our solutions would eventually unbind a finite-sized core. However, this does not constitute a violation of the instability properties of the singular isothermal sphere which is unstable both to collapse and to expansion. To emphasize this, we consider a purely expanding solution for isothermal spheres. This solution is found to be self-similar and results in a uniform density core in the central regions of the gas. Our solutions may be relevant to the 'luminosity' problem of protostellar cores since the predicted central accretion rates are significantly reduced relative to that of the expansion wave solution. Furthermore, our calculations indicate that star-forming cloud cores are not very tightly bound and that modest disturbances can easily result in both termination of infall and dispersal of unaccreted material.

Tsai, John C.↗

Protostellar Collapse with a Shock

We reexamine both numerically and analytically the collapse of the singular isothermal sphere in the context of low-mass star formation. We consider the case where the onset of collapse is initiated by some arbitrary process which is accompanied by a central output of either heat or kinetic energy. We find two classes of numerical solutions describing this manner of collapse. The first approaches in time the expansion wave solution of Shu, while the second class is characterized by an ever-decreasing central accretion rate and the presence of an outwardly propagating weak shock. The collapse solution which represents the dividing case between these two classes is determined analytically by a similarity analysis. This solution shares with the expansion wave solution the properties that the gas remains stationary with an r(sup -2) density profile at large radius and that, at small radius, the gas free-falls onto a nascent core at a constant rate which depends only on the isothermal sound speed. This accretion rate is a factor of approx. 0.1 that predicted by the expansion wave solution. This reduction is due in part to the presence of a weak shock which propagates outward at 1.26 times the sound speed. Gas in the postshock region first moves out subsonically but is then decelerated and begins to collapse. The existence of two classes of numerical collapse solutions is explained in terms of the instability to radial perturbations of the analytic solution. Collapse occurring in the manner described by some of our solutions would eventually unbind a finite-sized core. However, this does not constitute a violation of the instability properties of the singular isothermal sphere which is unstable both to collapse and to expansion. To emphasize this, we consider a purely expanding solution for isothermal spheres. This solution is found to be self-similar and results in a uniform density core in the central regions of the gas. Our solutions may be relevant to the 'luminosity' problem of protostellar cores since the predicted central accretion rates are significantly reduced relative to that of the expansion wave solution. Furthermore, our calculations indicate that star-forming cloud cores are not very tightly bound and that modest disturbances can easily result in both termination of infall and dispersal of unaccreted material.

Tsai, John C.↗

Thermal Control and Enhancement of Heat Transport Capacity of Two-Phase Loops With Electrohydrodynamic Conduction Pumping

There are three kinds of electrohydrodynamics (EHD) pumping based on Coulomb force: induction pumping, ion-drag pumping, and pure conduction pumping. EHD induction pumping relies on the generation of induced charges. This charge induction in the presence of an electric field takes place due to a non-uniformity in the electrical conductivity of the fluid which can be caused by a non-uniform temperature distribution and/or an inhomogeneity of the fluid (e.g. a two-phase fluid). Therefore, induction pumping cannot be utilized in an isothermal homogeneous liquid. In order to generate Coulomb force, a space charge must be generated. There are two main mechanisms for generating a space charge in an isothermal liquid. The first one is associated with the ion injection at a metal/liquid interface and the related pumping is referred to as ion-drag pumping. Ion-drag pumping is not desirable because it can deteriorate the electrical properties of the working fluid. The second space charge generation mechanism is associated with the heterocharge layers of finite thickness in the vicinity of the electrodes. Heterocharge layers result from dissociation of the neutral electrolytic species and recombination of the generated ions. This type of pumping is referred to as pure conduction pumping. This project investigates the EHD pumping through pure conduction phenomenon. Very limited work has been conducted in this field and the majority of the published papers in this area have mistakenly assumed that the electrostriction force was responsible for the net flow generated in an isothermal liquid. The main motivation behind this study is to investigate an EHD conduction pump for a two-phase loop to be operated in the microgravity environment. The pump is installed in the liquid return passage (isothermal liquid) from the condenser section to the evaporator section. Unique high voltage and ground electrodes have been designed that generate sufficient pressure heads with very low electric power requirements making the EHD conduction pumping attractive to applications such as two-phase systems (e.g. capillary pumped loops and heat pipes). Currently, the EHD conduction pump performance is being tested on a two-phase loop under various operating conditions in the laboratory environment. The simple non-mechanical and lightweight design of the EHD pump combined with the rapid control of performance by varying the applied electric field, low power consumption, and reliability offer significant advantages over other pumping mechanisms; particularly in reduced gravity applications.

Seyed-Yagoobi, J.↗

X-ray and Sunyaev-Zel'dovich Effect Measurements of the Gas Mass Fraction in Galaxy Clusters

We present gas mass fractions of 38 massive galaxy clusters spanning redshifts from 0.14 to 0.89, derived from Chandra X-ray data and OVRO/BIMA interferometric Sunyaev-Zel' dovich Effect (SZE) measurements. We use three models for the gas distribution: (1) an isothermal Beta-model fit jointly to the X-ray data at radii beyond 100 kpc and to all of the SZE data, (2) a nonisothermal double Beta-model fit jointly to all of the X-ray and SZE data, and (3) an isothermal Beta-model fit only to the SZE spatial data. We show that the simple isothermal model well characterizes the intracluster medium (ICM) outside of the cluster core, and provides consistently good fits to clusters spanning a wide range of morphological properties. The agreement in the results shows that the core can be satisfactorily accounted for by either excluding the core in fits to the X-ray data (the 100 kpc-cut model) or modeling the intracluster gas with a non-isothermal double Beta-model. We find that the SZE is largely insensitive to structure in the core.

LaRoque, Samuel J.↗

The RealGas and RealGasH2O Options of the TOUGH+ Code for the Simulation of Coupled Fluid and Heat Flow in Tight/Shale Gas Systems

We developed two new EOS additions to the TOUGH+ family of codes, the RealGasH2O and RealGas . The RealGasH2O EOS option describes the non-isothermal two-phase flow of water and a real gas mixture in gas reservoirs, with a particular focus in ultra-tight (such as tight-sand and shale gas) reservoirs. The gas mixture is treated as either a single-pseudo-component having a fixed composition, or as a multicomponent system composed of up to 9 individual real gases. The RealGas option has the same general capabilities, but does not include water, thus describing a single-phase, dry-gas system. In addition to the standard capabilities of all members of the TOUGH+ family of codes (fully-implicit, compositional simulators using both structured and unstructured grids), the capabilities of the two codes include: coupled flow and thermal effects in porous and/or fractured media, real gas behavior, inertial (Klinkenberg) effects, full micro-flow treatment, Darcy and non-Darcy flow through the matrix and fractures of fractured media, single- and multi-component gas sorption onto the grains of the porous media following several isotherm options, discrete and fracture representation, complex matrix-fracture relationships, and porosity-permeability dependence on pressure changes. The two options allow the study of flow and transport of fluids and heat over a wide range of time frames and spatial scales not only in gas reservoirs, but also in problems of geologic storage of greenhouse gas mixtures, and of geothermal reservoirs with multi-component condensable (H2O and CH4) and non-condensable gas mixtures. The codes are verified against available analytical and semi-analytical solutions. Their capabilities are demonstrated in a series of problems of increasing complexity, ranging from isothermal flow in simpler 1D and 2D conventional gas reservoirs, to non-isothermal gas flow in 3D fractured shale gas reservoirs involving 4 types of fractures, micro-flow, non-Darcy flow and gas composition changes during production.

03 NATURAL GAS↗

Ab initio study of phase transition and bulk modulus of NaH

The phase transition of NaH from NaCl- to CsCl-type structure is investigated by an ab initio plane-wave pseudopotential density functional theory method with the norm-conserving pseudopotential scheme in the frame of the generalized gradient approximation correction; the isothermal bulk modulus and its first and second pressure derivatives of the NaCl- and CsCl-type structures under high pressure and temperature are obtained through the quasi-harmonic Debye model. The phase transition obtained from the usual condition of equal enthalpies occurs at the pressure of 32 GPa, which is consistent with the experimental and other calculated values. Through the quasi-harmonic Debye model, in which the phononic effects are considered, the dependences of cell volume V and lattice constant a on temperature T at zero pressure, the isothermal bulk modulus B{sub 0} and its pressure derivatives B{sub 0}'and B{sub 0}'' on pressure P along isotherms 0, 300, and 600 K, are also successfully obtained. -- The isothermal bulk modulus B{sub T}, adiabatic bulk modulus B{sub S}, primitive cell volume V, and lattice constant a of an NaH with an NaCl-type structure as a function temperature T at zero pressure. When T<100 K, B nearly keeps constant; when T>100 K, B decreases dramatically as T increases. Correspondingly, when T<100 K, the primitive cell volume and lattice parameter of an NaH with an NaCl-type structure have a little change; when T>100 K, the primitive cell volume and lattice parameter changes rapidly as T increases. It is the rapid volume or lattice parameter variation that makes the bulk modulus B rapidly decrease. Display Omitted Research highlights: The transition phase of an NaH from NaCl to CsCl structure has been investigated. The relationship between B and T for an NaH at zero pressure has been given. The B{sub T} and its pressure derivatives of an NaH at high pressure have been obtained.

36 MATERIALS SCIENCE↗

Thermodynamical and structural insights of orange II adsorption by Mg{sub R}AlNO{sub 3} layered double hydroxides

[Mg{sub 1-x} Al{sub x}(OH){sub 2}][(NO{sub 3}){sub x}, nH{sub 2}O] Layered Double Hydroxide (LDH) sorbents with variable Mg/Al molar (R=(1-x)/x) ratios were investigated for adsorption of azo dye, orange II (OII) at various pH and temperature conditions. Mg{sub 2}AlNO{sub 3} displays the highest adsorption capacity with 3.611 mmol of OII per gram of Mg{sub 2}AlNO{sub 3} at 40 {sup o}C. Adsorption isotherms have been fitted using the Langmuir model and free energy of adsorption ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}) and entropy ({Delta}S{sup o}) were calculated. The experimental values for {Delta}G{sup o} in temperature range between 10 and 40 {sup o}C were found to be negative indicating that a spontaneous process occurred. Positive calculated enthalpy values, characteristic of an endothermic process were found. Characterization of solids (PXRD, FTIR, UV-vis, TGA/DTA, adsorption isotherm BET analysis, SEM and Zetametry) before and after adsorption showed that adsorption proceeds in two steps. First, adsorption occurs at the LDH surface, followed by intercalation via anion exchange. -- Graphical Abstract: Structural and thermodynamical insight of adsorption/Intercalation of OII in Mg{sub R}Al LDH Display Omitted Highlights: {yields} The nitrate containing hydrotalcite-like compounds (Mg{sub R}AlNO{sub 3} LDH) were prepared by the coprecipitation method. {yields} Adsorption of anionic orange dye(OII) is studied on LDHs at different temperatures. {yields} The adsorption process is well described by the Langmuir isotherm model. {yields} Mg{sub 2}AlNO{sub 3} displays the highest adsorption capacity with 3.611 mmol of OII per gram of Mg{sub 2}AlNO{sub 3} at 40 {sup o}C. {yields} Adsorption process does not occur on the surface of the LDH only but an intercalation process is also occurring concomitantly according to the thermodynamical values.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dependence of Water Vapour Adsorption on the Polarity of the Graphene Surfaces of Multi-wall Carbon Nanotubes

The adsorption of water by the graphene surfaces of multi-wall carbon nanotubes (MWCNTs) in either the untreated (4.3 atom% oxygen) or oxidised (22.3 atom% oxygen) surface states has been studied. Different concentrations of surface oxygen groups, which have been directly measured using XPS, give rise to distinctly different shapes of water adsorption isotherms. Those from the untreated materials follow the pressure axis which lends them a Type III character in the BDDT classification. However, since they display a clear point of inflection at the lowest pressure, they are strictly speaking Type II isotherms but indicative of relatively few polar interactions and weak water adsorptivity. In sharp contrast, the isotherms from the oxidised MWCNTs are typically Type II and are characterised by a marked positive curvature in their low pressure region due to the increased numbers of specific interactions occurring between water molecules and the polar surface oxygen groups. The water adsorption data were modelled by the equation of D'Arcy and Watt with a direct correlation being observed between the surface polarity parameters (amL and a0) and also as (the limiting water uptake) and the surface oxygen levels of the MWCNTs. The difference in polar surface energy was confirmed by measurements of the calorimetric enthalpies of immersion in water ( hi), which were -54 mJ/m2 for the untreated and -192 mJ/m2 for the oxidised materials. These values also reflect the difference in the integral net enthalpies of adsorption for the two hydrophilic surfaces: a value of ca. -35 mJ/m2 being obtained for an oxygen-free (hydrophobic) surface. Water adsorption on these hydrophilic graphene surfaces was shown to occur by specific hydrogen bonding and was therefore strongly dependent on the numbers of oxygen-containing polar surface sites. This behaviour is well known for other types of porous and non-porous carbon materials and is also predicted for carbon nanotubes by molecular simulation studies. The work described herein therefore provides early experimental confirmation of the quantitative role of surface oxygen chemistry in determining the water adsorption character of MWCNT graphene surfaces; it also validates previous simulation studies.

08 HYDROGEN↗

Study and Modeling of the Magnetocaloric Effect in the La{sub 0.67}Ba{sub 0.33}Mn{sub 0.9}Fe{sub 0.1}O{sub 3} Compound

The simulated magnetic entropy change of La{sub 0.67}Ba{sub 0.33}Mn{sub 0.9}Fe{sub 0.1}O{sub 3} manganite was determined using the mean field theory and a scaling method. Based on the Brillouin function, this method allowed us to simulate magnetic isotherms which are crucial for the simulation of the magnetic entropy change. The simulated entropy change is very close to that determined from experimental magnetic isotherms. In particular, the experimental and simulated maximum entropy change and relative cooling power are respectively suitable and in good agreement. The Bean–Rodbell model was used to simulate magnetization versus temperature curve. The obtained Curie temperature value is much well than that determined experimentally. Under low values of applied field, a phenomenological model has been intervened to simulate magnetization, magnetic entropy change, and the specific heat change versus temperature. This scaling method based on mean field theory leads to a direct estimation of the exchange parameter (λ ), the saturation magnetization (M{sub 0}), the total angular momentum (J), and the gyromagnetic factor (g) of our material. These parameters were used for simulating M(T,H) isotherms, which are used for the estimation of the magnetic entropy change (ΔS{sub M}) of La{sub 0.67}Ba{sub 0.33}Mn{sub 0.9}Fe{sub 0.1}O{sub 3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Equilibrium, kinetic, and thermodynamic studies on the sorption of some heavy metal ions by the phosphorus-containing polymer sorbent

The sorption of Cu+{sup 2}, Ni+{sup 2}, Co+{sup 2}, and Zn+{sup 2} ions onto the phosphorus-containing sorbent were studied as a function of the contact time, temperature, and concentration of the initial metal ions. The equilibrium studies are presented by the Langmuir, Freundlich, and Temkin isotherm models. The sorption data are well described by the Langmuir isotherm model, and they also can be simulated by the Freundlich isotherm model. The pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were applied to test the experimental data of the kinetic studies. The pseudo-second-order kinetic model provided the best correlation of the experimental data compared to the other kinetic models. The sorption capacity of the metal ions increased with temperature increasing. The positive value of enthalpy (ΔH°) and the negative value of Gibbs free energy (ΔG°) indicated that the sorption process was endothermic and spontaneous.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Processing Parameters and Shape of Blade on the Solidification of Single-Crystal CMSX-4 Ni-Based Superalloy

The effect of mold withdrawal velocity, heater and pouring temperatures and the thickness of blade root on the solidification parameters and shape of the liquidus isotherm as well as microstructure of single-crystal CMSX-4 nickel-based superalloy, manufactured by the Bridgman method, has been analyzed in the article. The temperature gradient G, solidification rate v and location of the liquidus isotherm were determined in relation to the radiation baffle on the basis of temperature measurements conducted in nine test points along the height of castings (140 mm) with different thicknesses of root (27, 15 and 7 mm) and withdrawal velocities of 3 and 5 mm/min. The increase of root thickness, relative to the airfoil, resulted in the rise of inhomogeneity of solidification parameters as well as the primary dendrite arm spacing and unsteady state solidification along the whole blade height. However, in the case of blade with constant thickness, the steady-state solidification was created at the distance of 65 to 130 mm from its base. The increase of mold withdrawal velocity caused the decrease of temperature gradient. However, the solidification rate was different from the mold withdrawal velocity, especially in the root and middle part of the airfoil. The increase of heater temperature resulted in a rise of temperature gradient and reduction of the curvature of the liquidus isotherm, whereas the pouring temperature did not affect the solidification parameters in the blade. Particularly unfavorable conditions of the solidification process could occur in the middle part of the airfoil and root because of the lowest value of G/v and the largest primary dendrite arm spacing.

36 MATERIALS SCIENCE↗

Modelisation of chloride reactive transport in concrete including thermodynamic equilibrium, kinetic control and surface complexation

In this study, a new physically and chemically based model taking into account thermodynamic equilibrium, kinetics and surface complexation is proposed to predict the ingress of chloride ions into saturated concretes. The numerical results of this multi-ionic model are compared to experimental data such as total and free chloride concentration profiles and chloride binding isotherms. With only one set of parameters, the results show very good agreement for chloride binding isotherm of concretes with different w/b, types of binders (CEM I, CEM III, and CEM I with fly ash) and various exposure conditions (NaCl solution at different concentrations). Such a model overcomes the use of empirical chloride binding isotherms that can be difficult to asses for concretes with supplementary cementitious materials. The very good results underline the need to take into account all the physical and chemical phenomena included in the model.

36 MATERIALS SCIENCE↗

Methylmercury sorption onto engineered materials

Four commercially available sorbents (BioChar (BC), ThiolSAMMS® (TS), SediMite (SM), and Organoclay™ PM-199 (OC-199)) were tested for their ability to sorb methylmercury (MeHg) and MeHg complexed with dissolved organic matter (DOM). Testing sorption behavior with DOM is more representative of the environmental conditions and mercury speciation expected during in-situ remediation efforts. Isotherms were fit using a robust, iterative re-weighting scheme. This fitting method improves upon the traditionally used indirect sorption method by removing the dependence between aqueous and solid phase concentrations in isotherm fitting. Developed isotherms reflect that without DOM, BC, TS, and SM adsorbed similar amounts of MeHg while OC-199 sorbed substantially less MeHg. Below an equilibrium concentration of 5.6 ng L -1 BC was the best performing sorbent, between 5.6 and 20. ng L -1 SM sorbed the most MeHg, and above an equilibrium concentration of 20.9 ng L -1 TS outperformed the other sorbents. BC and OC-199 showed indication of MeHg sorption saturation over the tested concentration range of 3.5–680 ng L -1 . With DOM, SM outperformed the other sorbents at equilibrium concentrations less than 0.98 ng L -1 and TS was the superior MeHg:DOM sorbent at higher concentrations. MeHg:DOM sorption was controlled by DOM-sorbent interactions. DOM decreased MeHg sorption onto BC and SM whereas TS exhibited similar sorption with and without DOM. OC-199 had slightly higher MeHg uptake with DOM. East Fork Poplar Creek (EFPC), an industrially Hg contaminated site, was used as a case study example to build a relationship between aqueous and fish MeHg concentrations and subsequently compare the cost of sorbent materials required to meet regulatory objectives. For this case study, SM provided the most cost-effective sorbent option for in-situ remediation efforts to reduce aqueous MeHg concentrations.

36 MATERIALS SCIENCE↗

Calorimetry can detect the early onset of hydrolysis in hybrid supercapacitors with aqueous electrolytes

This study investigates the effect of cation species on the onset of electrolyte hydrolysis in hybrid supercapacitors with aqueous electrolytes using isothermal operando calorimetry. The cells consisted of a positive α-MnO 2 cryptomelane electrode and a negative activated carbon (AC) electrode with either 0.5 M K 2 SO 4 or 0.5 M Cs 2 SO 4 aqueous electrolytes. They were characterized using cyclic voltammetry and galvanostatic cycling. In addition, the instantaneous heat generation rate at each electrode was measured using a custom isothermal operando calorimeter. Heat generation associated with resistive losses (Joule heating) and reversible ion adsorption/desorption was clearly identified. For larger potential windows, an endothermic dip, attributed to the onset of hydrolysis, was observed at the positive α-MnO 2 electrode where K + and Cs + ions engaged in fast surface redox reactions. Interestingly, this endothermic dip appeared at 1.8 V and 2.0 V for K 2 SO 4 and Cs 2 SO 4 aqueous electrolytes, respectively. The difference in the stable operating potential window was attributed to thinner solvation shell around Cs + cation than for K + thus reducing the amount of water present near the electrodes as ions partially shed their solvation shells during adsorption. The early onset of hydrolysis could be observed by isothermal operando calorimetry before it could be observed with conventional electrochemical methods.

42 ENGINEERING↗

Giant magnetic coercivity in orthorhombic YNi{sub 4}Si-type SmNi{sub 4}Si compound

Magnetic properties, magnetocaloric effect and heat capacity of the YNi{sub 4}Si-type SmNi{sub 4}Si compound have been investigated. SmNi{sub 4}Si exhibits ferromagnetic transition at 17 K. Below ~9 K, the magnetic isotherms of SmNi{sub 4}Si show metamagnetic-like behavior with critical field of 20 kOe at 5 K. Heat capacity measurements of SmNi{sub 4}Si show the electronic heat capacity coefficient γ=94 mJ/(mol K{sup 2}), phonon coefficient β=0.35 mJ/(mol K{sup 4}) and Debye temperature T{sub D}=310 K. The magnetocaloric effect of SmNi{sub 4}Si is calculated in terms of isothermal magnetic entropy change which is obtained by the isothermal magnetization (ΔS{sub m}{sup magn}) and heat capacity measurements (ΔS{sub m}{sup heat}). Both ΔS{sub m}{sup magn} and ΔS{sub m}{sup heat} reach a maximum of –1.0 J/kg K at 17 K for a field change of 50 kOe and they show positive values for a field change of 20 kOe at ~9 K. Below 15 K, SmNi{sub 4}Si shows large magnetic hysteresis with considerable remanence. At 5 K it exhibits giant coercive field of 58 kOe in an applied field of 90 kOe. - Highlights: • YNi{sub 4}Si-type SmNi{sub 4}Si has Curie point at 17 K. • ΔS{sub m}{sup magn} of SmNi{sub 4}Si reaches value of –1.0 J/kg K in 0–50 kOe near Curie point. • ΔS{sub m}{sup magn} of SmNi{sub 4}Si shows value of –0.4 and +0.8 J/kg K at 17 and 9 K in 0–20 kOe. • SmNi{sub 4}Si shows electronic heat capacity the 94 mJ/(mol K{sup 2}) and Debye T{sub D}=310 K. • SmNi{sub 4}Si shows huge magnetic hysteresis with coercive field of 58 kOe at 5 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗