Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAT PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

An experimental investigation with artificial sunlight of a solar hot-water heater

Thermal performance measurements were made of a commercial solar hot water heater in a solar simulator to determine basic performance characteristics of a traditional type of flat plate collector, with and without side reflectors (to increase the solar flux). Information on each of the following was obtained; (1) the effect of flow and incidence angle on the efficiency of a flat plate collector (but only without side reflectors); (2) transient performance under flow and nonflow conditions; (3) the effectiveness of reflectors to increase collector efficiency for a zero radiation angle at fluid temperatures required for solar air conditioning; and (4) the limits of applicability of a collector efficiency correlation based on the Hottel Whillier equation.

Simon, F. F.↗

The DOE photovoltaics program

As part of the National Solar Energy program, the US Department of Energy is now engaged in the development of technically feasible, low cost candidate component and system technologies to the point where technical readiness can be demonstrated by 1982. The overall strategy is to pursue parallel options that continue to show promise of meeting the program goals, thus increasing the probability that at least one technology will be successful. Included in technology development are both flat plate solar collectors and concentrator solar collectors, as well as the balance of system components, such as structures, power conditioning, power controls, protection, and storage. Generally, these last items are common to both flat plate and concentrator systems, but otherwise there is considerable disparity in design philosophy, photovoltaic cell requirements, and possible applications between the two systems. Objectives for research activities at NASA Lewis for stand alone applications, and at Sandia Laboratories where intermediate load center applications are addressed, are highlighted as well as college projects directed by Oak Ridge National Laboratory, and international applications managed by the Solar Energy Research Institute. Joint DOD/DOE effects for military applications are also summarized.

Ferber, R. R.↗

Concentrator hot-spot testing, phase 1

Results of a study to determine the hot-spot susceptibility of concentrator cells, to provide a hot-spot qualification test for concentrator modules, and to provide guidelines for reducing hot-spot susceptibility are presented. Hot-spot heating occurs in a photovoltaic module when the short-circuit current of a cell is lower than the string operating current forcing the cell into reverse bias with a concurrent power dissipation. Although the basis for the concentrator module hot-spot qualification test is the test developed for flat-plate modules, issues, such as providing cell illumination, introduce additional complexities into the testing procedure. The same general guidelines apply for protecting concentrator modules from hot-spot stressing as apply to flat-plate modules. Therefore, recommendations are made on the number of bypass diodes required per given number of series cells per module or source circuit. In addition, a new method for determining the cell temperature in the laboratory or in the field is discussed.

Gonzalez, C. C.↗

Low-cost solar array progress and plans

It is pointed out that significant redirection has occurred in the U.S. Department of Energy (DOE) Photovoltaics Program, and thus in the Flat-Plate Solar Array Project (FSA), since the 3rd European Communities Conference. The Silicon Materials Task has now the objective to sponsor theoretical and experimental research on silicon material refinement technology suitable for photovoltaic flat-plate solar arrays. With respect to the hydrochlorination reaction, a process proof of concept was completed through definition of reaction kinetics, catalyst, and reaction characteristics. In connection with the dichlorosilane chemical vapor desposition process, a preliminary design was completed of an experimental process system development unit with a capacity of 100 to 200 MT/yr of Si.Attention is also given to the silicon-sheet formation research area, environmental isolation research, the cell and module formation task, the engineering sciences area, and the module performance and failure analysis area.

Callaghan, W. T.↗

Wave phenomena in a high Reynolds number compressible boundary layer

The behavior of spatially unstable waves in a high Reynolds number compressible laminar boundary layer is investigated by solution of the laminar two-dimensional compressible Navier-Stokes equations (solved to fourth-order accuracy) over a flat plate with a fluctuating disturbance generated at the inflow. A significant nonlinear distortion is produced, in qualitative agreement with experimental data. It is shown that increasing compressibility can significantly stabilize the flow over a flat plate, and that the mechanism of phase cancellation is a viable mechanism for the control of growing disturbances.

Bayliss, A.↗

Sensor Development for Active Flow Control

Presented are the developmental efforts for MEMS sensors for a closed-loop active flow control in a low-speed wind tunnel evaluation. The MEMS sensors are designed in-house and fabricated out of house, and the shear sensors are a thermal type that are collocated with temperature and pressure sensors on a flexible polyimide sheet, which conforms to surfaces of a simple curvature. A total of 6 sensors are located within a 1.5 by 3 mm area as a cluster with each sensor being 300 pm square. The thickness of this sensor cluster is 75 pm. Outputs from the shear sensors have been compared with respect to those of the Preston tube for evaluation of the sensors on a flat plate. Pressure sensors are the absolute type and have recorded pressure measurements within 0.05 percent of the tunnel ESP pressure sensor readings. The sensors and signal conditioning electronics have been tested on both a flat plate and a ramp in Langley s 15-Inch Low-Turbulence Tunnel. The system configuration and control PC is configured with LabView, where calibration constants are stored for desired compensation and correction. The preliminary test results are presented within.

Kahng, Seun K.↗

Transitional Boundary-Layer Solutions Using a Mixing-Length and a Two-Equation Turbulence Model

Boundary-layer solutions were obtained using the conventional two-layer mixing-length turbulence model and the Wilcox-Traci two-equation model of turbulence. Both flatplate and blunt-body geometries were considered. The most significant result of the study is development of approximations for the two-equation model which permit streamwise stepsize comparable to that used in mixing-length computations. Additionally, a set of model-equation boundary conditions derived which apply equally well to both flat-plate and blunt-body geometries. Solutions obtained with the two-equations turbulence model are compared with experimental data and/or corresponding solutions obtained using the mixing-length model. Agreement is satisfactory for flat-plate boundary layers but not for blunt body boundary layers.

Anderson, E. C.↗

Potential of thin-film solar cell module technology

During the past five years, thin-film cell technology has made remarkable progress as a potential alternative to crystalline silicon cell technology. The efficiency of a single-junction thin-film cell, which is the most promising for use in flat-plate modules, is now in the range of 11 percent with 1-sq cm cells consisting of amorphous silicon, CuInSe2 or CdTe materials. Cell efficiencies higher than 18 percent, suitable for 15 percent-efficient flat plate modules, would require a multijunction configuration such as the CdTe/CuInSe2 and tandem amorphous-silicon (a-Si) alloy cells. Assessments are presented of the technology status of thin-film-cell module research and the potential of achieving the higher efficiencies required for large-scale penetration into the photovoltaic (PV) energy market.

Shimada, K.↗

Progress towards a model to describe jet/aerodynamic-surface interference effects

A first generation model is presented which relates the pressure distribution on an aerodynamic surface to properties of the jet plume. The characteristics of a jet in a cross flow are of primary importance in determining the pressure distribution on the aerodynamic surface and are assumed to be (1) a pair of contrasting vortices associated with a jet in a crossflow, (2) entrainment of crossflow fluid into the jet plume, and (3) a wake region near the aerodynamic surface and extending downstream from the jet orifice. The model is applied to the configuration of a round jet exhausting perpendicularly through a flat plate into a uniform crossflow for a range of jet-to-crossflow velocity ratios from three to ten. It is demonstrated that the model is capable of describing the measured pressure distribution on the flat plate with model parameters that are compatable with the incomplete description of the vortex pair that is available. The fore and moments on one plate are presented as functions of jet-to-crossflow velocity ratios.

Fearn, R. L.↗

Some comparisons of linear stability theory with experiment at supersonic and hypersonic speed

Measurements of waves initiated by wind-tunnel sounds are obtained for both supersonic and hypersonic speed. Flat-plate experiments carried out at Mach numbers of 4.5, 3.7, and 2.4 under the condition of laminar tunnel-wall boundary layers whereby a low background fluctuation level prevailed are outlined, as well as flat-plate experiments with sound-induced waves at supersonic speeds. Experimental studies of 'natural' wave growth on sharp cones at zero angle of attack and Mach numbers near 8 are discussed. Attention is focused on experimental research needed on boundary-layer receptivity to eddy Mach-wave radiation, hypersonic speed, and the stability-transition relationship in zero-pressure-gradient layers.

Kendall, James M., Jr.↗

Shock wave-boundary layer interactions in rarefied gas flows

A numerical study is presented, using the direct simulation Monte Carlo (DSMC) method, of shock wave-boundary layer interactions in low density supersonic flows. Test cases include two-dimensional, axially-symmetric and three-dimensional flows. The effective displacement angle of the boundary layer is calculated for representative flat plate, wedge, and cone flows. The maximum pressure, shear stress, and heat transfer in the shock formation region is determined in each case. The two-dimensional reflection of an oblique shock wave from a flat plate is studied, as is the three-dimensional interaction of such a wave with a sidewall boundary layer.

Bird, G. A.↗

Long Hole Film Cooling Dataset for CFD Development : Infrared Thermography and Thermocouple Surveys - Part 1

An experiment investigating flow and heat transfer of long (length to diameter ratio of 18) cylindrical film cooling holes has been completed. In this paper, the thermal field in the flow and on the surface of the film cooled flat plate is presented for nominal freestream turbulence intensities of 1.5 and 8 percent. The holes are inclined at 30deg above the downstream direction, injecting chilled air of density ratio 1.0 onto the surface of a flat plate. The diameter of the hole is 0.75 in. (0.01905 m) with center to center spacing (pitch) of 3 hole diameters. Coolant was injected into the mainstream flow at nominal blowing ratios of 0.5, 1.0, 1.5, and 2.0. The Reynolds number of the freestream was approximately 11,000 based on hole diameter. Thermocouple surveys were used to characterize the thermal field. Infrared thermography was used to determine the adiabatic film effectiveness on the plate. Hotwire anemometry was used to provide flowfield physics and turbulence measurements. The results are compared to existing data in the literature. The aim of this work is to produce a benchmark dataset for Computational Fluid Dynamics (CFD) development to eliminate the effects of hole length to diameter ratio and to improve resolution in the near-hole region. In this report, a Time-Filtered Navier Stokes (TFNS), also known as Partially Resolved Navier Stokes (PRNS), method that was implemented in the Glenn-HT code is used to model coolant-mainstream interaction. This method is a high fidelity unsteady method that aims to represent large scale flow features and mixing more accurately.

Shyam, Vikram↗

Impact and Penetration of Thin Aluminum 2024 Flat Panels at Oblique Angles of Incidence

The U.S. Federal Aviation Administration (FAA) and the National Aeronautics and Space Administration (NASA) are actively involved in improving the predictive capabilities of transient finite element computational methods for application to safety issues involving unintended impacts on aircraft and aircraft engine structures. One aspect of this work involves the development of an improved deformation and failure model for metallic materials, known as the Tabulated Johnson-Cook model, or MAT224, which has been implemented in the LS-DYNA commercial transient finite element analysis code (LSTC Corp., Livermore, CA) (Ref. 1). In this model the yield stress is a function of strain, strain rate and temperature and the plastic failure strain is a function of the state of stress, temperature and strain rate. The failure criterion is based on the accumulation of plastic strain in an element. The model also incorporates a regularization scheme to account for the dependency of plastic failure strain on mesh size. For a given material the model requires a significant amount of testing to determine the yield stress and failure strain as a function of the three-dimensional state of stress, strain rate and temperature. In addition, experiments are required to validate the model. Currently the model has been developed for Aluminum 2024 and validated against a series of ballistic impact tests on flat plates of various thicknesses (Refs. 1 to 3). Full development of the model for Titanium 6Al-4V is being completed, and mechanical testing for Inconel 718 has begun. The validation testing for the models involves ballistic impact tests using cylindrical projectiles impacting flat plates at a normal incidence (Ref. 2). By varying the thickness of the plates, different stress states and resulting failure modes are induced, providing a range of conditions over which the model can be validated. The objective of the study reported here was to provide experimental data to evaluate the model under more extreme conditions, using a projectile with a more complex shape and sharp contacts, impacting flat panels at oblique angles of incidence.

Ruggeri, Charles R.↗

Use of Glass Reinforced Concrete (GRC) as a substrate for photovoltaic modules

A substrate for flat plate photovoltaic solar panel arrays using a glass fiber reinforced concrete (GRC) material was developed. The installed cost of this GRC panel is 30% less than the cost goal of the Near Term Low-Cost Flat Plate Photovoltaic Solar Array Program. The 4 ft by 8 ft panel is fabricated from readily available inexpensive materials, weighs a nominal 190 lbs., has exceptionally good strength and durability properties (rigid and resists weathering), is amenable to mass production and is easily installed on simple mountings. Solar cells are encapsulated in ethylene/vinyl acetate with Tedlar backing and Korad cover film. The laminates are attached to the GRC substrate with acrylic transfer tape and edge sealed with silicone RTV adhesive.

Eirls, J. L.↗

Measurements of forces, moments, and pressures on a generic store separating from a box cavity at supersonic speeds

An experimental investigation was conducted to measure the forces, moments, and pressure distributions on the generic store separating from a rectangular box cavity contained in a flat plate surface at supersonic speeds. Pressure distributions inside the cavity and oil flow and vapor-screen photographs of the cavity flow field were also obtained. The measurements were obtained for the store separating from a flat plate surface, from two shallow cavities having length to depth ratios (L/h) of 16.778 and 12.073, and from a deep cavity having L/h = 6.730. Measurements for the shallow cavities were obtained both with and without rectangular doors attached to sides of the cavities. The tests were conducted at free stream Mach numbers of 1.69, 2.00 and 2.65 for a free stream Reynolds number per foot of 2 x 10(exp 6). Presented here are a discussion of the results, a complete tabulation of the pressure data, figures of both the pressure and force and moment data, and representative oil flow and vapor screen photographs.

Stallings, Robert L., Jr.↗

The Effect of Porosity on the Lift and Drag of Bird's Wings

Bird's wings are porous. The mass flux through the wings for various simulated wing loadings was measured and found to average about 2 x 10(exp -4) g/s.sq cm for one feather thickness at the average pigeon wing loading of 45 newtons/sq m. The calculated effect of the flux on lift was found to be less than 1/2 of 1%. Experiments at a typical pigeon flight Reynolds number of 10(exp 5) on flat plates with 3.5% and 14.5% open area spread over the trailing 58% of the chord showed that it is possible to both increase and decrease profile drag, relative to the drag on a non-porous flat plate, by < or = 5%. Stall on the porous plates occurred up to 3 deg earlier than stall on the non-porous plates. From lift calculations and drag measurements it is shown that the effects of porosity on the gliding characteristics of birds are negligible.

Lichter, Seth↗

Long Hole Film Cooling Dataset for CFD Development - Flow and Film Effectiveness

An experiment investigating flow and heat transfer of long (length to diameter ratio of 18) cylindrical film cooling holes has been completed. In this paper, the thermal field in the flow and on the surface of the film cooled flat plate is presented for nominal freestream turbulence intensities of 1.5 and 8 percent. The holes are inclined at 30 deg above the downstream direction, injecting chilled air of density ratio 1.0 onto the surface of a flat plate. The diameter of the hole is 0.75 in. (approx. 0.02 m) with center to center spacing (pitch) of 3 hole diameters. Coolant was injected into the mainstream flow at nominal blowing ratios of 0.5, 1.0, 1.5, and 2.0. The Reynolds number of the freestream was approximately 11,000 based on hole diameter. Thermocouple surveys were used to characterize the thermal field. Infrared thermography was used to determine the adiabatic film effectiveness on the plate. Hotwire anemometry was used to provide flowfield physics and turbulence measurements. The results are compared to existing data in the literature. The aim of this work is to produce a benchmark dataset for Computational Fluid Dynamics (CFD) development to eliminate the effects of hole length to diameter ratio and to improve resolution in the near-hole region. In this report, a Time Filtered Navier Stokes (TFNS), also known as Partially Resolved Navier Stokes (PRNS), method that was implemented in the Glenn-HT code is used to model coolant-mainstream interaction. This method is a high fidelity unsteady method that aims to represent large scale flow features and mixing more accurately.

Shyam, Vikram↗

Effects of roughness on heating and boundary-layer transition. Part 2: effects of discrete roughness on heating

A preliminary investigation on the effects of roughness on heating in delta wing orbiters was conducted on the windward surface of the vehicle. The purpose of the experiment was to determine the feasibility of using parametric relationships obtained from discrete roughness effects on heating in flat plates and cones, to complex shuttle configurations. An attempt was also made to characterize what parameters were needed to influence roughness. Experimental results show that effective roughness Reynolds numbers are less than or equal to those of flat plates at the same edge Mach number, but, the roughness correlations for plates and cones cannot be applied to the shuttle configuration.

Mateer, G. G.↗