Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FINITE ELEMENT METHOD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Multi-Scale Thermal Analysis for Design of SiC-Based Medium Voltage Motor Drive: Preprint

This paper describes a multi-scale thermal analysis approach for the design of an air-cooled 1.7-kV SiC MOSFET-based medium-voltage variable-speed motor drive. The National Renewable Energy Laboratory supported the project objectives by providing thermal management design support to the project partner The Ohio State University (OSU). The scope of the models and limited resources required efficient and flexible thermal models to be developed. Two modeling techniques are described that significantly reduced model run time and enabled more complex models to be run faster while retaining needed accuracy. The first technique uses the effectiveness-NTU method to extract convection boundary conditions from a computational fluid dynamics (CFD) model that can be applied to a fast-running finite element analysis model. The second is a porous media technique that enables system-level CFD simulations that incorporate effects from heat exchangers (e.g., pin fin heat sinks) that run in a fraction of the time required for fully resolved CFD simulations. The multi-scale approach to the thermal analysis enabled fast and accurate simulation for the converter design ranging from the die level up to the full system with 36 submodules. The modeling results were validated against experimental data from system tests performed by OSU.

DIRECT ENERGY CONVERSION↗
DOE OSTI2023

An $\bar{F}$ Meshfree Treatment for Nearly Incompressible Materials

The computational modeling of nearly incompressible materials is a difficult task for many numerical methods, and even after several decades of investigation, it is still an active research area. This report seeks to address the treatment of incompressible materials in meshfree methods using a synergistic combination of two treatments. The first treatment is an $\bar{F}$ method, where the decomposed dilatational and deviatoric parts are calculated over different smoothing domains. The second treatment “activates” additional nodes throughout the domain to increase the flexibility of the model. We implement this synergistic combination in the context of the reproducing kernel particle method (RKPM) and present results for the Cook’s membrane benchmark problem. The results are compared with those using the composite tet10 finite element with a volume-averaged J formulation. We show that the combined treatment is an effective way to deal with nearly incompressible materials in a meshfree framework and compares well with other highly-effective treatments.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Scalable Multiphysics Block Preconditioning for Low Mach Number Compressible Resistive MHD with Application to Magnetic Confinement Fusion

This study investigates multiphysics block preconditioners that are critical in devising scalable Newton–Krylov iterative solvers for longer time-scale fully implicit fluid plasma models. The specific model of interest is the visco-resistive, low Mach number, compressible magnetohydrodynamics (MHD) model. This model describes the dynamics of conducting fluids in the presence of electromagnetic fields and can be used to study aspects of astrophysical phenomena, important science and technology applications, and basic plasma physics. The specific application of interest that motivates this study is the macroscopic simulation of longer time-scale stability and disruptions of magnetic confinement fusion devices, specifically the ITER Tokamak. The computational solution of the governing balance equations for mass, momentum, heat transfer, and magnetic induction for resistive MHD systems can be extremely challenging. These difficulties arise from both the strong nonlinear, nonsymmetric coupling of fluid and electromagnetic phenomena as well as the significant range of time and length scales that the interactions of these physical mechanisms produce. To handle the range of time and spatial scales of interest, a fully implicit unstructured variational multiscale finite element formulation is employed. For the scalable solution of the Newton linearized systems, fully coupled block preconditioners are designed to leverage algebraic multigrid subsolves. In conclusion, results are presented for the strong and weak scaling of the method as well as the robustness of these techniques for a large range of Lundquist numbers.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Weak boundary conditions for Lagrangian shock hydrodynamics: A high-order finite element implementation on curved boundaries

Here, we propose a new Nitsche-type approach for weak enforcement of normal velocity boundary conditions for a Lagrangian discretization of the compressible shock-hydrodynamics equations using high-order finite elements on curved boundaries. Specifically, the variational formulation is appropriately modified to enforce free-slip wall boundary conditions, without perturbing the structure of the function spaces used to represent the solution, with a considerable simplification with respect to traditional approaches. Total energy is conserved and the resulting mass matrices are constant in time. The robustness and accuracy of the proposed method are validated with an extensive set of tests involving nontrivial curved boundaries.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Evaluation of the ring tension test (RTT) for robust determination of material strengths

The ring tension test (RTT) is an experimental method for determining mechanical behavior in a material’s circumferential or hoop direction. It is a crucial test for testing anisotropic materials with tube geometry, such as nuclear fuel cladding or irradiated pipes. Several RTT configurations exist, each with their own advantages and disadvantages. However, this test is significantly more complex than traditional tensile testing and can be especially sensitive to small differences and inconsistencies in the test setup and geometry, ultimately affecting the derived mechanical properties. Previous research has focused on method development, and little work has been done on understanding the subtle differences between an ideal test and experiments, specifically when the tests are performed on highly irradiated materials in hot cells. In this work, a finite element-based investigation of the RTT is conducted to fill this gap. The two most used test configurations are investigated, comparing their ability to determine accurate material strengths through plastic deformation. Several non-ideal conditions and uncontrollable effects which are likely to occur during experimental testing such as machining tolerances, variations of specimen geometry from nominal dimensions, rotation of specimens and fixturing, and other test setup discrepancies are studied. The sensitivity of measured strengths to these conditions is presented. A mechanics-based approach to describing and correcting raw data to determine actual strengths is also included for one of the configurations, resulting in a robust correction method with highly accurate material strength measurements. Finally, based on these analyses, the hemicylindrical mandrel configuration is recommended with a gauge region oriented at a 45° angle.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Simulation-driven optimization of high-order meshes in ALE hydrodynamics

Here we propose tools for high-order mesh optimization and demonstrate their benefits in the context of multi-material Arbitrary Lagrangian-Eulerian (ALE) compressible shock hydrodynamic applications. The mesh optimization process is driven by information provided by the simulation which uses the optimized mesh, such as shock positions, material regions, known error estimates, etc. These simulation features are usually represented discretely, for instance, as finite element functions on the Lagrangian mesh. The discrete nature of the input is critical for the practical applicability of the algorithms we propose and distinguishes this work from approaches that strictly require analytical information. Our methods are based on node movement through a high-order extension of the Target-Matrix Optimization Paradigm (TMOP). The proposed formulation is fully algebraic and relies only on local Jacobian matrices, so it is applicable to all types of mesh elements, in 2D and 3D, and any order of the mesh. We discuss the notions of constructing adaptive target matrices and obtaining their derivatives, reconstructing discrete data in intermediate meshes, node limiting that enables improvement of global mesh quality while preserving space-dependent local mesh features, and appropriate normalization of the objective function. The adaptivity methods are combined with automatic ALE triggers that can provide robustness of the mesh evolution and avoid excessive remap procedures. The benefits of the new high-order TMOP technology are illustrated on several simulations performed in the high-order ALE application BLAST.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Enhanced Collisional Losses from a Magnetic Mirror Using the Lenard-Bernstein Collision Operator

Collisions are crucial in governing particle and energy transport in plasmas confined in a magnetic mirror trap. Modern gyrokinetic codes model transport in magnetic mirrors, but some utilize approximate model collision operators. This study focuses on a Pastukhov-style method of images calculation of particle and energy confinement times using a Lenard-Bernstein model collision operator. Prior work on parallel particle and energy balances used a different Fokker-Planck plasma collision operator. The method must be extended in non-trivial ways to study the Lenard-Bernstein operator. To assess the effectiveness of our approach, we compare our results with a modern finite element solver. Our findings reveal that the particle confinement time scales like a exp( a 2 ) using the Lenard-Bernstein operator, in contrast to the more accurate scaling that the Coulomb collision operator would yield a 2 exp( a 2 ), where a 2 is approximately proportional to the ambipolar potential. We propose that codes solving for collisional losses in magnetic mirrors utilizing the Lenard-Bernstein or Dougherty collision operator scale their collision frequency of any electrostatically confined species. This study illuminates the collision operator’s intricate role in the Pastukhov-style method of images calculation of collisional confinement.

fusion plasma↗
DOE OSTI2024

A hybrid Monte Carlo, discontinuous Galerkin method for linear kinetic transport equations

Here we present a hybrid method for time-dependent particle transport problems that combines Monte Carlo (MC) estimation with deterministic solutions based on discrete ordinates. For spatial discretizations, the MC algorithm computes a piecewise constant solution and the discrete ordinates use bilinear discontinuous finite elements. From the hybridization of the problem, the resulting problem solved by Monte Carlo is scattering free, resulting in a simple, efficient solution procedure. Between time steps, we use a projection approach to “relabel” collided particles as uncollided particles. In conclusion, from a series of standard 2-D Cartesian test problems we observe that our hybrid method has improved accuracy and reduction in computational complexity of approximately an order of magnitude relative to standard discrete ordinates solutions.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

BISON Robustness and Performance Improvements

BISON is a modern finite-element based nuclear fuel performance code that has been under development at the Idaho National Laboratory (USA) since 2009 [1]. The code is applicable to both steady and transient fuel behavior and can be used to analyze 1D (spherically symmetric), 2D (axisymmetric and generalized plane strain) or 3D geometries. BISON is the fuel performance code used within CASL for LWR fuel under both normal operating and accident conditions. BISON is built using the INL Multiphysics ObjectOriented Simulation Environment, or MOOSE [2, 3]. MOOSE is a massively parallel, finite element-based framework to solve systems of coupled non-linear partial differential equations using the Jacobian-Free Newton Krylov (JFNK) method [4]. This enables investigation of computationally large problems, for example a full stack of discrete pellets in a LWR fuel rod, or every rod in a full reactor core. MOOSE supports the use of complex two and three-dimensional meshes and uses implicit time integration, important for the widely varied time scale in nuclear fuel simulation. An object-oriented architecture is employed which greatly minimizes the programming effort required to add new material and behavioral models. The flexibility of the implicit and fully coupled multiphysics approach comes with a need for constructing suitable approximations for the Jacobian matrix of the coupled system used for either preconditioning a Krylov solve or in a direct Newton solve. Preconditioning options for Bison problems need to be revisited with new preconditioning methods becoming available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Observation and Modeling of Dynamic Fracture Behaviors of Battery Cell Under Impact Loading Using Enhanced Representative Volume Element Concept

The burgeoning electric automobile industry has increased interest in battery safety. Battery cells experience significant mechanical stress during operation, including the impact of accidents and vibrations from driving. The potential for thermal runaway reactions in battery cells raises safety concerns. Although numerous researchers have defined the dynamic behavior of battery cells and proposed numerical models to describe it, few studies have focused on the high-strain rate mechanical impact phase correlated with the onset of fracture. In this study, we describe the dynamic behavior of pouch battery cells and propose a modeling method to study their mechanical failure under impact situations. Impact tests are conducted at various velocities and heights. To overcome numerical issues commonly encountered under rapid deformation scenarios, a new finite element model is developed based on the representative volume element model. The proposed approach efficiently simulates continuous crack propagation and brittleness behavior during impact by permitting the individual behavior of the cell components. Therefore, engineers can reliably design safer electric vehicle battery cells by measuring the properties of the cell components.

ENERGY STORAGE↗
DOE OSTI2024

Hybridized Discontinuous Galerkin Methods for Computational Fluid Dynamics

Hybridizable Discontinuous Galerkin (HDG) methods hold promise for any applications with significant advection character, including thermal hydraulics in light water reactors and advanced reactor concepts and fluid models of plasmas in magnetic confinement fusion. Its features include natural upwinding, local element conservation, and extensibility to arbitrarily high order accuracy. In the last fiscal year we have implemented HDG in the Multiphysics Object-Oriented Simulation Environment (MOOSE). We developed a first-of-its-kind automatic static condensation system in MOOSE’s underlying finite element library libMesh which can condense out arbitrarily many internal variables. Finally, we developed the first preconditioner for HDG discretizations of the Navier-Stokes equations which shows robust performance across a wide range of problem sizes and Reynolds numbers. This preconditioner yields solution times that are equivalent to the fastest developed for industry standard finite volume methods. Moreover, the arbitrarily high-order nature of HDG makes it a prime candidate for acceleration via graphical processing units (GPUs). We believe these developments will hold significant importance for future DOE Nuclear Energy (NE) and Fusion Energy Science (FES) programs.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Simulation of gas mixture dynamics in a pipeline network using explicit staggered-grid discretization

Here we develop an explicit staggered finite difference discretization scheme for simulating the transport of highly heterogeneous gas mixtures through pipeline networks. This study is motivated by the proposed blending of hydrogen into natural gas pipelines to reduce end use carbon emissions while using existing pipeline systems throughout their planned lifetimes. Our computational method accommodates an arbitrary number of constituent gases with very different physical properties that may be injected into a network with significant spatiotemporal variation. In this setting, the gas flow physics are highly location- and time- dependent, so that local composition and nodal mixing must be accounted for. The resulting conservation laws are formulated in terms of pressure, partial densities and flows, and volumetric and mass fractions of the constituents. We include non-ideal equations of state that employ linear approximations of gas compressibility factors, so that the pressure dynamics propagate locally according to a variable wave speed that depends on mixture composition and density. We derive compatibility relationships for network edge boundary values that are more complex than for a homogeneous gas. The simulation method is evaluated on initial boundary value problems for a single pipe and a small network, is cross-validated with a lumped element simulation, and used to demonstrate a local monitoring and control policy for maintaining allowable concentration levels.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Interface capturing simulations of bubble population effects in PWR subchannels

As the computational power of high-performance computing (HPC) facilities grows, so too does the feasibility of using first principle based simulation to study turbulent two-phase flows within complex pressurized water reactor (PWR) geometries. Direct numerical simulation (DNS), integrated with an interface capturing method, allows for the collection of high-fidelity numerical data using advanced analysis techniques. The research presented here employs the massively parallel, finite-element based, unstructured mesh code, PHASTA, to simulate a set of two-phase bubbly flows through PWR subchannel geometries including auxiliary structures (spacer grids and mixing vanes). The main objective of the presented work is to analyze bubble dynamics and turbulence interactions at varying bubble concentrations to support the development of advanced two-phase flow closure models. Turbulent two-phase flows in PWR subchannels were simulated at hydraulic Reynolds numbers of 81,000 with bubble concentrations of 3%–15% by gas volume fraction (768–3928 resolved bubbles, respectively) and compared against a 1% void fraction case (262 bubbles) that had been previously simulated. The finite element mesh utilized for the study at higher bubble concentrations was composed of 1.55 billion elements, compared to the previous study which employed 1.11 billion elements, ensuring all turbulence scales and individual bubbles within the flow are fully resolved. For each case, the resolved initial bubble size was 0.65 mm in diameter (resolved with 25 grid points across the diameter). The simulations were analyzed to find flow features such as the mean velocity profile, bubble relative velocity and the effect of the bubbles on the turbulent conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

MASTODON: An Open-Source Software for Seismic Analysis and Risk Assessment of Critical Infrastructure

Seismic analysis and risk assessment of safety-critical infrastructure like hospitals, nuclear power plants, dams, and facilities handling radioactive materials involve computationally intensive numerical models and coupled multiphysics scenarios. They are also performed in a strict regulatory environment that requires high software quality assurance standards, and in the case of safety-related nuclear facilities, a conformance to the American Society of Mechanical Engineers Nuclear Quality Assurance (NQA-1) standard. This paper introduces the open-source finite-element software, MASTODON (Multi-hazard Analysis of Stochastic Time-Domain Phenomena), which implements state-of-the-art seismic analysis and risk assessment tools in a quality-controlled environment. MASTODON is built on MOOSE (Multi-physics Object-Oriented Simulation Environment), which is a highly parallelizable, NQA-1 conforming, coupled multiphysics, finite-element framework developed at Idaho National Laboratory. MASTODON is capable of fault rupture and source-to-site wave propagation using the domain reduction method, nonlinear site response, and soil-structure interaction analysis, implicit and explicit time integration, automated stochastic simulations, and seismic probabilistic risk assessment. When coupled with other MOOSE applications, MASTODON can also solve strongly and weakly coupled multiphysics problems. This paper presents a summary of the capabilities of MASTODON and some demonstrative examples.

42 ENGINEERING↗
DOE OSTI2024

Performance-based earthquake early warning for tall buildings

The ShakeAlert Earthquake Early Warning (EEW) system aims to issue an advance warning to residents on the West Coast of the United States seconds before the ground shaking arrives, if the expected ground shaking exceeds a certain threshold. However, residents in tall buildings may experience much greater motion due to the dynamic response of the buildings. Therefore, there is an ongoing effort to extend ShakeAlert to include the contribution of building response to provide a more accurate estimation of the expected shaking intensity for tall buildings. Currently, the supposedly ideal solution of analyzing detailed finite element models of buildings under predicted ground-motion time histories is not theoretically or practically feasible. The authors have recently investigated existing simple methods to estimate peak floor acceleration (PFA) and determined these simple formulas are not practically suitable. Instead, this article explores another approach by extending the Pacific Earthquake Engineering Research Center (PEER) performance-based earthquake engineering (PBEE) to EEW, considering that every component involved in building response prediction is uncertain in the EEW scenario. Additionally, while this idea is not new and has been proposed by other researchers, it has two shortcomings: (1) the simple beam model used for response prediction is prone to modeling uncertainty, which has not been quantified, and (2) the ground motions used for probabilistic demand models are not suitable for EEW applications. In this article, we address these two issues by incorporating modeling errors into the parameters of the beam model and using a new set of ground motions, respectively. We demonstrate how this approach could practically work using data from a 52-story building in downtown Los Angeles. Using the criteria and thresholds employed by previous researchers, we show that if peak ground acceleration (PGA) is accurately estimated, this approach can predict the expected level of human comfort in tall buildings.

58 GEOSCIENCES↗
DOE OSTI2021

Hierarchical model reduction driven by a proper orthogonal decomposition for parametrized advection-diffusion-reaction problems

This work combines the Hierarchical Model (HiMod) reduction technique with a standard Proper Orthogonal Decomposition (POD) to solve parametrized partial differential equations for the modeling of advection-diffusion-reaction phenomena in elongated domains (e.g., pipes). This combination leads to what we define as HiPOD model reduction, which merges the reliability of HiMod reduction with the computational efficiency of POD. Two HiPOD techniques are presented and assessed by an extensive numerical verification.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Design and Analysis of Multifidelity Finite Element Simulations

Abstract The numerical accuracy of finite element analysis (FEA) depends on the number of finite elements used in the discretization of the space, which can be varied using the mesh size. The larger the number of elements, the more accurate the results are. However, the computational cost increases with the number of elements. In current practice, the experimenter chooses a mesh size that is expected to produce a reasonably accurate result, and for which the computer simulation can be completed in a reasonable amount of time. Improvements to this approach have been proposed using multifidelity modeling by choosing two or three mesh sizes. However, mesh size is a continuous parameter, and therefore, multifidelity simulations can be performed easily by choosing a different value for the mesh size for each of the simulations. In this article, we develop a method to optimally find the mesh sizes for each simulation and satisfy the same time constraints as a single or a double mesh size experiment. A range of different mesh sizes used in the proposed method allows one to fit multifidelity models more reliably and predict the outcome when meshes approach infinitesimally small, which is impossible to achieve in actual simulations. We illustrate our approach using an analytical function and a cantilever beam finite element analysis experiment.

Engineering↗
DOE OSTI2022

Non-intrusive reduced order modeling of natural convection in porous media using convolutional autoencoders: Comparison with linear subspace techniques

Natural convection in porous media is a highly nonlinear multiphysical problem relevant to many engineering applications (e.g., the process of CO 2 sequestration). Here, we extend and present a non-intrusive reduced order model of natural convection in porous media employing deep convolutional autoencoders for the compression and reconstruction and either radial basis function (RBF) interpolation or artificial neural networks (ANNs) for mapping parameters of partial differential equations (PDEs) on the corresponding nonlinear manifolds. To benchmark our approach, we also describe linear compression and reconstruction processes relying on proper orthogonal decomposition (POD) and ANNs. Further, we present comprehensive comparisons among different models through three benchmark problems. The reduced order models, linear and nonlinear approaches, are much faster than the finite element model, obtaining a maximum speed-up of 7 × 10 6 because our framework is not bound by the Courant–Friedrichs–Lewy condition; hence, it could deliver quantities of interest at any given time contrary to the finite element model. Our model’s accuracy still lies within a relative error of 7% in the worst-case scenario. We illustrate that, in specific settings, the nonlinear approach outperforms its linear counterpart and vice versa. We hypothesize that a visual comparison between principal component analysis (PCA) and t-Distributed Stochastic Neighbor Embedding (t-SNE) could indicate which method will perform better prior to employing any specific compression strategy.

97 MATHEMATICS AND COMPUTING↗