Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Device for steam cladding oxidation testing at TREAT

To compare the chemical degradation of conventional zirconium alloy (Zry) cladding to advance silicon carbide (SiC) cladding in a post loss of coolant accident (LOCA) environment, new nuclear testing capabilities are necessary. The Transient Reactor Test (TREAT) Facility at Idaho National Laboratory (INL) has matured its transient fuel testing capabilities since its 2017 restart. The most recent experiment architecture is the Transient Water Irradiation System in TREAT (TWIST), which is designed to support qualification of accident tolerant fuels in light water reactors. INL has designed and analyzed a natural circulation steam flow modification for TWIST to produce prototypic conditions of cladding oxidation. The in-situ device will be electrically heated to drive natural circulation. Moreover, the SiC cladding requires heating above 1700 °C to observe failure, thus internal prototypic nuclear heating with radiation effects will be used. Thermal hydraulic analysis with RELAP5-3D (Reactor Excursion and Leak Analysis Program) estimated steam fluxes greater than 50 mg cm −2 s −1 can be achieved. These fluxes are adequate to test Zry cladding according to draft regulatory guides and to test SiC cladding according to past experiments.

Oxidation↗
DOE OSTI2026

Simple device modification simultaneously enhances indoor passive evaporative cooling power and duration

Passive evaporative cooling from a damp cloth or vessel can be used for localized cooling of perishables such as food and medicine, drinking water, and even people. Such applications have two key objectives, which are normally in tension with each other: minimizing the water consumption rate and maximizing the cooling (steady-state temperature swing between the cool cloth and the warm surroundings). Here, we present a simple device that delivers higher performance in both metrics simultaneously by adding a perforated aluminum foil sheet suspended over a stagnant air layer to thermally shield the evaporating surface while also facilitating mass transfer. Experimental results demonstrate a simultaneous 10%–25% increase in temperature swing and 2–3× reduction in water consumption rate as compared to conventional evaporative cooling. This improvement is achieved through careful modeling to optimize the coupled heat and mass transfer through the airgap (thermally insulating and vapor permeable) and perforated foil (infrared reflective and vapor permeable).

Chen, Sarah Mizuno↗
DOE OSTI2021

A tutorial on radio frequency sheath physics for magnetically confined fusion devices

Radio frequency (RF) sheaths occur under a wide variety of conditions when RF waves, material surfaces and plasma coexist. RF sheaths are of special importance in describing the interaction of ion cyclotron range of frequency (ICRF) waves with the boundary plasma in tokamaks, stellarators and other magnetic confinement devices. In this article the basic physics of RF sheaths is discussed in the context of magnetic fusion research. Techniques for modelling RF sheaths, their interaction with RF wave fields and the resulting consequences are highlighted. The article is intended as a guide for the early-career ICRF researcher, but it may equally well serve to provide an overview of basic RF sheath concepts and modelling directions for any interested fusion scientist.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of the electron density and temperature gradient on drift-wave turbulence in the Large Plasma Device

In this paper we present an experimental study of edge turbulence in the Large Plasma Device at UCLA. We utilize a scan of discharge power and prefill pressure (neutral density) to show experimentally that turbulent density fluctuations decrease with decreasing density gradient, as predicted for resistive drift-wave turbulence (RDWT). As expected for RDWT, we observe that the cross-phase between the density and potential fluctuations is close to 0. Moreover, the addition of an electron temperature gradient leads to a reduction in the amplitude of the density fluctuations, as expected for RDWT. However, counter to theoretical expectations, we find that the potential fluctuations do not follow the same trends as the density fluctuations for changes either in density gradients or the addition of a temperature gradient. The disconnect between the density and potential fluctuations is connected to changes in the parallel flows as a result of differences in the prefill pressure, i.e. neutral density. Further analysis of the density and potential fluctuation spectra show that the electron temperature gradient reduces the low frequency fluctuations up to $10 \,{\rm kHz}$ and the introduction of a temperature gradient leads to an unexpected ${\sim }{\rm \pi}$ shift of the density–potential cross-phase at ${\sim }10\,{\rm kHz}$ , while maintaining the typical resistive drift-wave cross-phase at lower frequencies. These experiments partly confirm existing knowledge on resistive drift-wave turbulence, but also introduce new observations that indicate a need for dedicated nonlinear three-dimensional turbulence simulations that include neutrals.

Physics↗
DOE OSTI2024

Plasma potential shaping using end-electrodes in the Large Plasma Device

We perform experiments in the Large Plasma Device at the University of California, Los Angeles, studying how different end-electrode biasing schemes modify the radial potential profile in the machine. We impose biasing profiles of different polarities and gradient signs on a set of five concentric electrodes placed 12 m downstream from the plasma source. We find that imposing concave-down profiles (negative potential radial gradient) on the electrodes creates radial potential profiles halfway up the plasma column that are comparable to those imposed on the electrodes and a few electron temperature in height, regardless of the biasing polarity. On the other hand, imposing concave-up profiles (positive potential radial gradient) leads to non-monotonic radial potential profiles. This observation can be explained by the current drawn through the electrodes and the parallel plasma resistivity, highlighting their important role in controlling the rotation of plasma. Concave-down plasma potential profiles, obtained by drawing electrons on the axis, are predicted to drive azimuthal drift velocities that can approach significant fractions of the ion sound speed in the central region of the plasma column.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Three-Dimensional Mass Spectrometric Imaging of Biological Structures Using a Vacuum-Compatible Microfluidic Device

Three-dimensional (3D) molecular imaging of biological structures is important for a wide range of research. In recent decades, secondary ion mass spectrometry (SIMS) has been recognized as a powerful technique for both two-dimensional (2D) and 3D molecular imaging. Sample fixations (e. g., chemical fixation and cryogenic fixation methods) are necessary to adapt biological samples to the vacuum condition in the SIMS chamber, which has been demonstrated to be non-trivial and less controllable, thus limiting the wider application of SIMS on 3D molecular analysis of biological samples. Our group recently developed in situ liquid SIMS that offers great opportunities for the molecular study of various liquids and liquid interfaces. In this work, we demonstrate that a further development of the vacuum-compatible microfluidic device used in in situ liquid SIMS provides a convenient freeze-fixation of biological samples and leads to more controllable and convenient 3D molecular imaging. The special design of this new vacuum-compatible liquid chamber allows an easy determination of sputter rates of ice, which is critical for calibrating the depth scale of frozen biological samples. Sputter yield of a 20 keV Ar 1800 + ion on ice has been determined as 1500 (± 8%) water molecules per Ar 1800 + ion, consistent with our results from molecular dynamics simulations. Moreover, using the information of ice sputter yield, we successfully conduct 3D molecular imaging of frozen homogenized milk and observe network structures of interesting organic and inorganic species. Finally, taken together, our results will significantly benefit various research fields relying on 3D molecular imaging of biological structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Proton Conducting Neuromorphic Materials and Devices

Neuromorphic computing and artificial intelligence hardware generally aims to emulate features found in biological neural circuit components and to enable the development of energy-efficient machines. In the biological brain, ionic currents and temporal concentration gradients control information flow and storage. It is therefore of interest to examine materials and devices for neuromorphic computing wherein ionic and electronic currents can propagate. Protons being mobile under an external electric field offers a compelling avenue for facilitating biological functionalities in artificial synapses and neurons. In this review, we first highlight the interesting biological analog of protons as neurotransmitters in various animals. We then discuss the experimental approaches and mechanisms of proton doping in various classes of inorganic and organic proton-conducting materials for the advancement of neuromorphic architectures. Since hydrogen is among the lightest of elements, characterization in a solid matrix requires advanced techniques. We review powerful synchrotron-based spectroscopic techniques for characterizing hydrogen doping in various materials as well as complementary scattering techniques to detect hydrogen. First-principles calculations are then discussed as they help provide an understanding of proton migration and electronic structure modification. Outstanding scientific challenges to further our understanding of proton doping and its use in emerging neuromorphic electronics are pointed out.

36 MATERIALS SCIENCE↗
DOE OSTI2025

X-ray Transient Absorption Spectroscopy Reveals Light Responses of Cobalt Centers in Co-Pi OER Catalytical Devices under Electrochemical Biases

Here, operando X-ray transient absorption measurements were successfully performed for the first time on the Co-Pi catalyst, confirming a photoreduction in Co-Pi under 400 nm blue light excitation. This provides key insights into spectroelectrochemical mechanistic studies of relevant oxygen evolution catalysts and guidance for photocatalysis using these metal oxides. Limiting blue-light exposure of these films should allow for better self-healing and higher turnover in photon-driven water oxidation. These results also demonstrate the importance of performing XTA measurements under operating conditions. Further development of this technique will allow for analysis of complex materials such as tethered molecules on surfaces and in complex device architectures to yield beneficial data for applied materials.

electrochemical cells↗
DOE OSTI2025

A Computational Framework for Simulations of Dissipative Nonadiabatic Dynamics on Hybrid Oscillator-Qubit Quantum Devices

Here, we introduce a computational framework for simulating nonadiabatic vibronic dynamics on circuit quantum electrodynamics (cQED) platforms. Our approach leverages hybrid oscillator-qubit quantum hardware with midcircuit measurements and resets, enabling the incorporation of environmental effects such as dissipation and dephasing. To demonstrate its capabilities, we simulate energy transfer dynamics in a triad model of photosynthetic chromophores inspired by natural antenna systems. We specifically investigate the role of dissipation during the relaxation dynamics following photoexcitation, where electronic transitions are coupled to the evolution of quantum vibrational modes. Our results indicate that hybrid oscillator-qubit devices, operating with noise levels below the intrinsic dissipation rates of typical molecular antenna systems, can achieve the simulation fidelity required for practical computations on near-term and early fault-tolerant quantum computing platforms.

Hamiltonians↗
DOE OSTI2024

Bismuth in Lead–Tin Alloy Perovskites: Effect on Material Properties and Photovoltaic Device Performance

Metal halide perovskites (MHPs) have a strong potential for optoelectronic applications, especially photovoltaics. A significant advantage offered by MHPs is their bandgap tunability via chemical substitution and alloying, with lead–tin alloys producing the narrowest reported bandgaps of ~1.2 eV. Efforts to further narrow the bandgap of MHPs by alloying in other elements, such as bismuth, have largely been unsuccessful due to the introduction of defective electronic states, which severely diminish electronic quality. Here, in this study, we examine the effects of bismuth on a lead–tin alloyed MHP, motivated by the narrow bandgap of alloyed lead–tin MHPs. We find that the defect screening observed in lead–tin MHPs is not sufficient to screen the defect level introduced by bismuth, as evidenced by quenched photoluminescence, decreased mobility, and severely reduced performance in a photovoltaic device. Density functional theory calculations suggest that midgap states are introduced by bismuth addition over a range of chemical and compositional conditions. We further observe through wavelength-dependent photoconductivity that free carriers are generated out to ~0.9 eV in bismuth-containing samples, which could be of potential interest for NIR photodetection.

14 SOLAR ENERGY↗
DOE OSTI2020

Curved Three-Dimensional Cobalt Nanohelices for Use in Domain Wall Device Applications

Three-dimensional fabrication of nanostructures opens new possibilities to not only understand the fundamental effects of shape and of the interactions between the nanostructures, but also to develop novel technological applications. Of course, this is of particular importance for magnetic nanostructures, where curvilinear geometry can lead to the emergence of novel topological effects and spin excitations. In this work, we have used the focused electron beam ion deposition (FEBID) method to fabricate three-dimensional magnetic cobalt nanohelices with controlled geometry such as chirality, and curvature. Additionally, using a combination of off-axis electron holography and electron tomography, we are able to determine the way in which the quantitative nanoscale magnetization distribution is related to the 3D morphology and curvature of the nanohelices. These results pave a way forward for development of future 3D magnetic nanostructures to explore novel physics as well as for applications such as magnetic field sensors, spin-wave filters, and magneto-optical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Growth of Nanometer-Thick γ-InSe on Si(111) 7 × 7 by Molecular Beam Epitaxy for Field-Effect Transistors and Optoelectronic Devices

γ-InSe is a semiconductor that holds promising potential in high-performance field-effect transistors and optoelectronic devices. Large-scale, single-phase γ-InSe deposition has proven challenging because of the difficulty in precise control of stoichiometry and the coexistence of different indium selenide phases. In this study, we demonstrate the wafer-scale combinatorial approach to map out the growth window as functions of the Se/In ratio and growth temperature for γ-InSe on the Si(111) 7 × 7 substrate in molecular beam epitaxy. X-ray diffraction (XRD) was used to identify the indium selenide phases, while atomic force microscopy revealed four distinct surface morphologies of γ-InSe, enabling a discussion of the growth mechanisms associated with each morphology. Cross-sectional atomic resolution scanning transmission electron microscopy confirmed that the film was of high crystalline quality and had nearly single-phase γ-InSe. In conclusion, our comprehensive study elucidates the In–Se phase map for thin film growth parameters, providing invaluable landmarks for the reproducible synthesis of high-quality γ-InSe layers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tuning the Magnetic Properties of CrI 3 Using Ni Thin Film Deposition for Applications in Spintronic Devices

Chromium triiodide (CrI 3 ), a van der Waals magnet, has recently been shown to host Ising ferromagnetism down to the monolayer limit. It is a potentially important material in 2D magnet-based applications, such as magnetic sensors and spintronic devices. Prior studies have revealed the coexistence of two different types of interlayer magnetic coupling, the antiferromagnetic (AFM) coupling near the surface and ferromagnetic (FM) coupling in the deep bulk layers, in pristine CrI 3 crystals below the Curie temperature. In this study, we used Ni thin film deposition to tune the surface magnetic states in bulk CrI 3 . A nanometer thickness (4 nm thick) of Ni was deposited on the surface of CrI 3 using electron-beam evaporation to form a Ni/CrI 3 heterostructure. The deposited Ni thin layer forms nanoclusters that completely cover the CrI 3 surface. Magnetic states of CrI 3 before and after Ni deposition are probed by ultralow-frequency magneto-Raman spectroscopy. Instead of seeing three spin wave branches in Raman scattering below 2 T, as in pristine bulk CrI 3 , in Ni/CrI 3 , we observe only a single spin wave branch, which is softened compared to that in pristine CrI 3 and displays a Zeeman shift under an out-of-plane magnetic field up to 7 T. This observation reveals that the AFM layers on pristine CrI 3 crystal surfaces transit into FM layers, so the entire CrI 3 crystal is in the FM state after Ni deposition. First-principles calculations show that Ni atoms tend to diffuse into the CrI 3 lattice, and the FM interlayer coupling has a much lower energy than AFM coupling in the presence of Ni atoms. As a result, our studies show that the magnetic state of CrI 3 can be modified through deposition of a thin metal layer on the surface, offering a route for controlling the spin degree of freedom in van der Waals magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chemical Vapor Deposition-Grown Hexagonal Boron Nitride and Graphene for Tandem Dielectric Capacitive Polymer Devices

To address the low energy density of polymeric capacitors, this work explores how tandem combinations of antagonistic properties can enhance energy storage. We introduce multilayer architecture integrating chemical vapor deposition (CVD)-grown ≈2 nm hexagonal boron nitride (hBN) and graphene with ferroelectric polyvinylidene fluoride (PVDF) and linear polyetherimide (PEI) layers to suppress leakage paths, reduce loss, and promote Maxwell–Wagner–Sillars polarization. Raman spectroscopy, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), and plasma focused ion beam (PFIB) analyses confirm robust material integration. In conclusion, for the tandem device, E BD ≈600 V/μm, while individual layers show lower values (PVDF|Graphene (Gr)|PVDF ≈ 50 V/μm and PEI|hBN|PEI ≈ 275 V/μm), yielding an overall ≈6000% enhancement and demonstrating the effectiveness of the 2D multilayer design.

Chemical vapor deposition (CVD)↗
DOE OSTI2024

Simultaneous Solid Electrolyte Deposition and Cathode Lithiation for Thin Film Batteries and Lithium Iontronic Devices

Here we show that the deposition of the solid-state electrolyte LiPON onto films of V 2 O 5 leads to their uniform lithiation of up to 2.2 Li per V 2 O 5 , without affecting the Li concentration in the LiPON and its ionic conductivity. Our results indicate that Li incorporation occurs during LiPON deposition, in contrast to earlier mechanisms proposed to explain postdeposition Li transfer between LiPON and LiCoO 2 . We use our discovery to demonstrate symmetric thin film batteries with a capacity of >270 mAh/g, at a rate of 20C, and 1600 cycles with only 8.4% loss in capacity. We also show how autolithiation can simplify fabrication of Li iontronic transistors attractive for emerging neuromorphic computing applications. Our discovery that LiPON deposition results in autolithiation of the underlying insertion oxide has the potential to substantially simplify and enhance the fabrication process for thin film solid state Li ion batteries and emerging lithium iontronic neuromorphic computing devices.

25 ENERGY STORAGE↗
DOE OSTI2022

Charge-Density-Wave Thin-Film Devices Printed with Chemically Exfoliated 1T-TaS 2 Ink

In this work, we report on the preparation of inks containing fillers derived from quasi-two-dimensional charge-density-wave materials, their application for inkjet printing, and the evaluation of their electronic properties in printed thin-film form. The inks were prepared by liquid-phase exfoliation of CVT-grown 1T-TaS 2 crystals to produce fillers with nm-scale thickness and μm-scale lateral dimensions. Exfoliated 1T-TaS 2 was dispersed in a mixture of isopropyl alcohol and ethylene glycol to allow fine-tuning of filler particles thermophysical properties for inkjet printing. The temperature-dependent electrical and current fluctuation measurements of printed thin films demonstrated that the charge-density-wave properties of 1T-TaS 2 are preserved after processing. The functionality of the printed thin-film devices can be defined by the nearly commensurate to the commensurate charge-density-wave phase transition of individual exfoliated 1T-TaS 2 filler particles rather than by electron-hopping transport between them. The obtained results are important for the development of printed electronics with diverse functionality achieved by the incorporation of quasi-two-dimensional van der Waals quantum materials.

1T-TaS2↗
DOE OSTI2021

Visualizing the strongly reshaped skyrmion Hall effect in multilayer wire devices

Magnetic skyrmions are nanoscale spin textures touted as next-generation computing elements. When subjected to lateral currents, skyrmions move at considerable speeds. Their topological charge results in an additional transverse deflection known as the skyrmion Hall effect (SkHE). While promising, their dynamic phenomenology with current, skyrmion size, geometric effects and disorder remain to be established. Here we report on the ensemble dynamics of individual skyrmions forming dense arrays in Pt/Co/MgO wires by examining over 20,000 instances of motion across currents and fields. The skyrmion speed reaches 24 m/s in the plastic flow regime and is surprisingly robust to positional and size variations. Meanwhile, the SkHE saturates at ~22 ° , is substantially reshaped by the wire edge, and crucially increases weakly with skyrmion size. Particle model simulations suggest that the SkHE size dependence - contrary to analytical predictions - arises from the interplay of intrinsic and pinning-driven effects. These results establish a robust framework to harness SkHE and achieve high-throughput skyrmion motion in wire devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ultracompact mirror device for forming 20-nm achromatic soft-X-ray focus toward multimodal and multicolor nanoanalyses

Abstract Nanoscale soft-X-ray microscopy is a powerful analysis tool in biological, chemical, and physical sciences. To enhance its probe sensitivity and leverage multimodal soft-X-ray microscopy, precise achromatic focusing devices, which are challenging to fabricate, are essential. Here, we develop an ultracompact Kirkpatrick-Baez (ucKB) mirror, which is ideal for the high-performance nanofocusing of broadband-energy X-rays. We apply our advanced fabrication techniques and short-focal-length strategy to realize diffraction-limited focusing over the entire soft-X-ray range. We achieve a focus size of 20.4 nm at 2 keV, which represents a significant improvement in achromatic soft-X-ray focusing. The ucKB mirror extends soft-X-ray fluorescence microscopy by producing a bicolor nanoprobe with a 1- or 2-keV photon energy. We propose a subcellular chemical mapping method that allows a comprehensive analysis of specimen morphology and the distribution of light elements and metal elements. ucKB mirrors will improve soft-X-ray nanoanalyses by facilitating photon-hungry, multimodal, and polychromatic methods, even with table-top X-ray sources.

Science & Technology - Other Topics↗